Orion XTR-X4R, XTR, X4R Owner's Manual
4-Way Electronic Crossover Network
w/Remote Level Control
XTR-X4R
OWNER’S MANUAL
TABLE OF CONTENTS
WHAT’S IN THE BOX
PRACTICE SAFE SOUND
TM
RECORD YOUR SERIAL NUMBER AND DATE
1
10
INTRODUCTION...
ORION
To ensure your warranty (see back cover), please record
the following information regarding your new amplifier.
Model:
Serial Number:
Date of Purchase:
Purchased from:
WHAT’S IN THE BOX
PRACTICE SAFE SOUND
TM
RECORD YOUR SERIAL NUMBER AND DATE
2 channel input & 4 channel output electronics crossover
Red light illuminated control panel
Rotary control knobs
12dB per octave crossover slope
PWM power supply
Remote level controls
Front & sub/rear input mode switch
Variable low pass frequency control 50Hz-500Hz
(SUB/REAR OUTPUT)
Manual on/off switch on each output channel
Variable bass boost controls 0dB-12dB
Stereo/mono mode control on front input
Variable high-pass frequency control 90Hz-1.1KHz
(MID OUTPUT)
Variable low-pass frequency control 2KHz-8KHz(MID OUTPUT)
Band pass/ high pass selector(MID OUTPUT)
Sub & rear phase shift control 0-180
Variable high-pass frequency control 1.2KHz-14KHz
(HIGH OUTPUT)
Adjustable level control on all output channels
Max variable output level controls 11 volts
Variable Subsonic filter control 20Hz-40Hz
FEATURES AND SPECIFICATIONS
1
POW ER
SUB SON IC FIL TER LOW P ASS LOW P ASS PHA SE
180
0
BA SS BOO ST
0 dB +12 d B
PHA SE
0 180
HIG H PAS S HIG H PAS S
MON O
STE REO
ON
OFF
ON
OFF
ON
OFF
ON
OFF
MOD E
FRO NT
SUB /REA R
INP UT
LEV EL
MIN MAX
LEV EL
MIN MAX
LEV EL
MIN MAX
LEV EL
MIN MAX
FUS E
+12 V
REM OTE
GRO UND
R
L
FRON T
INPU T
SUB /REA R
INPU T
R
L
FLAT
OUTP UT
R
L
SUB/ REAR
OUTP UT
R
L
MID
OUTP UT
R
L
HIGH
OUTP UT
R
L
4-WA Y EL EC T RO NI C CR OS SOVER
FL AT OUT PUT
SU B/RE AR OU TPU T
MI D OUTP UT
HI GH OUT PUT
SU B/RE AR IN PUT
FR ONT IN PUT
REM OTE
20H z 40H z 50H z 500H z
2KH z 8KHz
MOD E
HIGH P ASS
BAND P ASS
90H z 1.2 KHz1.1 KHz
14K Hz
XTR -X 4R
3
6
9
10
5
7
2
22
17
18
19
20
21
23
4
24
811
12
13
141516
REMOTE
CONTROL
MIN MAX
XTR -X 4R
FEATURES AND SPECIFICATIONS
1. LEVEL CONTROL
2. PHASE SWITCH
3.VARIABLE HIGH-PASS FREQUENCY CONTROL
4.HIGH OUTPUT LEVEL CONTROL
5.VARIABLE LOW-PASS FREQUENCY CONTROL
6.BAND PASS/HIGH PASS SELECTOR
7.VARIABLE HIGH-PASS FREQUENCY CONTROL
8.MID OUTPUT LEVEL CONTROL
9.VARIABLE LOW-PASS FREQUENCY CONTROL
10. PHASE CONTROL
11.SUB/REAR OUTPUT LEVEL CONTROL
12.SUBSONIC FILTER
13.BASS BOOST CONTROL
14.FLAT OUTPUT LEVEL CONTROL
15.SUB/REAR/FRONT INPUT SWITCH
16.STEREO/MONO INPUT SWITCH
17.SUB/REAR INPUT PORT
18.FLAT OUTPUT PORT
19.SUB/REAR OUTPUT PORT
20.MID OUTPUT PORT
21.HIGH OUTPUT PORT
22.FRONT INPUT PORT
23.REMOTE CONTROL JACK
24.POWER TERMINALS
This control sets the sub/rear gain control.
Shift allows 0 degree to 180 degrees.
By turning the selector you can choose the high-pass crossover points from 1.2KHz-14KHz.
For adjusting the high output level.
By turning the selector you can choose the low-pass crossover points from 2KHz-8KHz.
When this switch is in high pass mode, the low pass filter cannot be used. it can convert rear
channel to band pass in tri amp system.
By turning the selector you can choose the high-pass crossover points from 90Hz-1.1KHz.
For adjusting the mid output level.
By turning the selector you can choose the low-pass crossover points from 50Hz-500Hz.
Shift allows 0 degree to 180 degrees.
For adjusting the sub/rear output level.
Use this control to filter out low frequency noise and rumble.
This control adjusts the bass boost gain(0 to12dB)
For adjusting the flat output level.
For selection of independent input or input from front RCA
For selection of stereo or mono mode front inputs.
To be connected to the sub/rear outputs of the source unit.
To be connected to the amplifier left/right inputs.
To be connected to the sub channel amplifier left/right inputs.
To be connected to the rear channel amplifier left/right inputs.
To be connected to the front channel amplifier left/right inputs.
To be connected to the front outputs of the source unit.
Plug the modular telephone style cord connected to the remote control unit into this jack
Use these connectors to deliver power, ground, and remote turn-on control to the unit
0dB-12dB
1.2KHz-14KHz
90Hz-1.1KHz
2KHz-8KHz
50Hz-500Hz
20Hz-40Hz
-High Pass
-Mid High Pass
-Mid Low Pass
-Sub/rear(Low Pass)
-Subsonic Filter
more than 90dB
11V
5.9˝x12.7˝x1.8˝
150 x 322 x 45.5
This control sets the sub/rear level control.
Loading...