How it Works
Orion
Loading...
OSHD-410H
Installation Manual
95 pgs3.6 Mb0

Orion OSHD-410H, OSHD-810, OSHD-1610 Installation Manual

OSHD-410H & OSHD-810 & OSHD-1610
OSHD-410H/OSHD-810/OSHD-1610
Digital Video Recorder
Installation / User Manual
OSHD-410H & OSHD-810 & OSHD-1610
HD-CCTV DVR
Install & User Guide
HD-CCTV DVR Manual. Thank you for purchasing a Orion Technology A/S Digital Video Recorder. Before installation or operation please become familiar with the user manual and other referenced manuals mentioned in the booklet. User manual, software and hardware described here are protected by copyright by law. With the exception of copying for general use within fair use, copying and reprinting of the user manual, either partially or in entirety, or translating it into any another language without the consent of our Corporate office is strictly prohibited.
Product Warranty and Limited Responsibility
The manufacturer does not assume any responsibility concerning the sale of this product and does not delegate any right to any third party to take any responsibility on its behalf. The product warranty does not cover cases of accidents, negligence, alteration, misuse or abuse. No warranty is offered for any attachments or parts not supplied by the manufacturer.
The manufacturer does not assume any responsibility for followings
Malfunctions due to negligence by user  Deliberate disassembly and replacement by user  Connection of power source other than a properly rated power source  Malfunctions caused by natural disasters (fire, flood, tidal wave, etc)  The warranty period for HDD is one year  Any data damage due to HDD damage
The product is not for exclusive use of crime prevention but for assistance in cases as fire or theft. We take no responsibility for damage from any incident.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB
cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to
promote the sustainable reuse of material resources.
OSHD-410H & OSHD-810 & OSHD-1610
Household users should contact either the retailer where they purchased this product or their local government office, for details of where and how they can
take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household
waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above
the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free
battery return system.
Copyright ©2012 ORION TECHNOLOGY A/S. All rights reserved.
OSHD-410H & OSHD-810 & OSHD-1610
0. Introduction
0.1. Warning
Warning
Please do not bend or press power cord by force which could lead to fire. Be careful not to pull Do not pull power cord by force or with wet hands to avoid fire or electric shock. In case of changing built-in lithium battery, it should be replaced with same brand or similar one to prevent a danger of
explosion. Since old batteries could be a factor of environment contamination, please disposed of them properly.
Do not throw the batteries in fire or heating units. Neither short circuit nor disassembly is prohibited. Do not recharge
battery used for remote controller.
 Do not open the top cover otherwise it could lead to electric shock and product damage.  The previous recorded data is deleted if record continues when HDD is full so please check disk setup status.  Manufacturer takes no responsibility for any damaged data due to customer’s carelessness or negligence.
Caution
Do not place heavy objects on the top of the produc, it will damage the unit Product is for indoor use only and it is not for outdoor use. Use product to its environmental specifications
(Temperature & Humidity). To clean the product, gently wipe the outside with a clean dry cloth.
Product uses AC power of 110V ~ 240V. Be cautious not to cause electric damages to the product. Be careful not to drop the product. Physical shocks may harm the product including internal HDD. In addition, please
make sure the product is secured after installation.
Product is made of metal you can hurt another human if you throw or used as a weapon. Keep away from the reach
of children.
If Product does not operate properly, please contact the closest ORION TECHNOLOGY A/S distributor for service.
Tampering or disassembling the product will void the warranty.
The product can transmit real time video over network or internet and can be used for monitoring purpose based on
installation. So please check and review related regulations before installation. Experience and technical skills are needed for the installation of this product. Improper installation may cause fire, electric shocks, or defects. Any installation job should be performed by the vendor you purchased this product from.
The content of this manual can differ according to firmware or Software upgrading, and the standard and appearance of products may be changed for the improvement of quality without an advance notice. System Power Off In case user turn off device by force while device is working, it could give damage on HDD and device so please turn off device safely using power button located in the front panel. Working Temperature The working temperature of the product is 5°C~45°C or 41°F~113°F. Product may not work properly out of recommended working temperature range for a long period of time. Please keep this product within recommended temperature range.
OSHD-410H & OSHD-810 & OSHD-1610
CCOONNTTEENNTTSS
0. INTRODUCTION ............................................................................................................ 3
0.1. Warning ...................................................................................................................................................... 3
1. KEY FEATURES ............................................................................................................ 9
1.1. Accessories .............................................................................................................................................. 12
1.2. Description & Function ............................................................................................................................. 13
1.2.1. Front .................................................................................................................................................. 13
1.2.2. Rear .................................................................................................................................................. 15
1.2.3. Remote Controller ............................................................................................................................. 15
1.2.3.1. Remote Controller ID setup ........................................................................................................... 16
1.2.3.2. Select remote controller ID ............................................................................................................ 16
2. INSTALLATION ............................................................................................................ 17
2.1. Before Installation .................................................................................................................................... 17
2.1.1. RACK installation .............................................................................................................................. 17
2.1.2. Caution for HDD installation .............................................................................................................. 17
2.1.3. HDD installation ................................................................................................................................ 17
2.1.4. Add HDD ........................................................................................................................................... 18
2.2. Connecting other devices ......................................................................................................................... 19
2.2.1. Basic connections ............................................................................................................................. 19
2.2.1.1. Connecting monitor ....................................................................................................................... 19
2.2.1.2. Connecting camera ....................................................................................................................... 20
2.2.1.3. Connecting power ......................................................................................................................... 20
2.2.1.4. Connecting audio .......................................................................................................................... 20
2.2.2. Connection map with other devices .................................................................................................. 21
2.2.3. Connecting external device .............................................................................................................. 21
2.2.3.1. Connecting USB Device ................................................................................................................ 21
2.2.3.2. Connecting eSATA Device ............................................................................................................ 21
2.2.4. Connecting OSN-04ST ..................................................................................................................... 22
2.2.4.1. Connecting OSN-04ST with DVR .................................................................................................. 22
2.2.4.2. Set ID setup ................................................................................................................................... 22
2.2.5. Connecting and configuring DIO ports .............................................................................................. 22
2.2.5.1. Wire handling ................................................................................................................................ 22
2.2.5.2. Inserting & removing wire .............................................................................................................. 23
2.2.5.3. Connecting sensor ........................................................................................................................ 23
2.2.5.4. Connecting relay ........................................................................................................................... 23
2.2.5.5. Connecting COM1 serial port with external devices ..................................................................... 24
2.2.5.6. Connecting COM2,3 serial port ..................................................................................................... 24
2.2.5.7. Configuring an extension of PTZ & Keybaord ............................................................................... 25
3. MENU USAGE ............................................................................................................. 27
3.1. Menu Structure ......................................................................................................................................... 27
OSHD-410H & OSHD-810 & OSHD-1610
3.2. Function Menu ......................................................................................................................................... 27
3.3. Factory Reset ........................................................................................................................................... 27
3.4. OSD menu configuration .......................................................................................................................... 28
3.4.1. Menu structure .................................................................................................................................. 28
3.4.2. Basic Setting ..................................................................................................................................... 29
3.4.2.1. Viewing Image. .............................................................................................................................. 29
3.4.2.2. Setting Date & Time ...................................................................................................................... 29
3.4.2.3. Record Setting ............................................................................................................................... 30
3.5. Use of Input/output devices...................................................................................................................... 31
3.5.1. Copy .................................................................................................................................................. 31
3.5.2. Sensor Setting .................................................................................................................................. 32
3.5.2.1. All Sensor ...................................................................................................................................... 32
3.5.2.2. Each Sensor .................................................................................................................................. 32
3.5.3. Relay Setting ..................................................................................................................................... 32
3.5.4. Serial Setting ..................................................................................................................................... 32
3.5.4.1. Serial (COM1) Setting ................................................................................................................... 32
3.5.4.2. Text Setting .................................................................................................................................... 33
3.5.5. HDD Use ........................................................................................................................................... 33
3.5.5.1. HDD Registration & Format ........................................................................................................... 33
3.5.5.2. HDD Replacement ........................................................................................................................ 33
3.5.6. Remote monitoring & control ............................................................................................................ 34
3.5.6.1. Ethernet Connection ...................................................................................................................... 34
3.5.6.2. Network Setting ............................................................................................................................. 34
4. MONITORING .............................................................................................................. 35
4.1. Login Screen ............................................................................................................................................ 35
4.2. Basic Screen ............................................................................................................................................ 35
4.3. Single Screen ........................................................................................................................................... 35
4.4. Multi Screen ............................................................................................................................................. 35
4.5. Screen Description ................................................................................................................................... 35
4.6. Auto Switch Mode(Sequence) ................................................................................................................. 36
4.7. Event Screen ............................................................................................................................................ 36
4.8. Zoom Screen Mode .................................................................................................................................. 36
4.9. Pause Live Screen ................................................................................................................................... 37
4.10. PTZ Control .......................................................................................................................................... 37
4.10.1. Focus ............................................................................................................................................. 37
4.10.2. Zoom ............................................................................................................................................. 37
4.10.3. Pan/Tilt/Zoom ................................................................................................................................ 38
4.10.4. Load Preset ................................................................................................................................... 38
4.10.5. Save Preset ................................................................................................................................... 38
4.10.6. Auxiliary On ................................................................................................................................... 38
OSHD-410H & OSHD-810 & OSHD-1610
4.10.7. Auxiliary Off ................................................................................................................................... 38
4.10.8. Menu ............................................................................................................................................. 38
5. SEARCH & PLAYBACK .............................................................................................. 39
5.1. Playback ................................................................................................................................................... 39
5.1.1. Playback with Basic Screen .............................................................................................................. 39
5.1.2. Playback Function ............................................................................................................................. 39
5.2. Search Mode ............................................................................................................................................ 40
5.2.1. Time Search ...................................................................................................................................... 40
5.2.2. Calendar Search ............................................................................................................................... 40
5.2.3. Event Search .................................................................................................................................... 40
5.2.4. Thumbnail Search ............................................................................................................................. 41
5.3. Copy ......................................................................................................................................................... 41
5.3.1. DVD .................................................................................................................................................. 41
5.3.2. EXE ................................................................................................................................................... 41
5.3.3. AVI .................................................................................................................................................... 42
6. CONFIGURATION ....................................................................................................... 43
6.1. System Setup ........................................................................................................................................... 43
6.1.1. Date/Time.......................................................................................................................................... 43
6.1.1.1. Time Setup .................................................................................................................................... 43
6.1.1.2. NTP Setup ..................................................................................................................................... 44
6.1.2. Disk ................................................................................................................................................... 45
6.1.2.1. Disk Manager ................................................................................................................................ 46
6.1.2.2. Disk Status .................................................................................................................................... 47
6.1.2.3. Disk Mirroring ................................................................................................................................ 47
6.1.2.4. Mirroring HDD Replacement ......................................................................................................... 49
6.1.3. User Setup ........................................................................................................................................ 50
6.1.4. Utility ................................................................................................................................................. 51
6.2. Network .................................................................................................................................................... 53
6.2.1. xDSL ................................................................................................................................................. 55
6.2.2. WRS .................................................................................................................................................. 55
6.2.3. Radius ............................................................................................................................................... 56
6.3. Device Setup ............................................................................................................................................ 56
6.3.1. Camera Setup ................................................................................................................................... 56
6.3.1.1. Using Channel ............................................................................................................................... 57
6.3.1.2. Title ................................................................................................................................................ 57
6.3.1.3. Input Resolution ............................................................................................................................ 57
6.3.2. Monitor Setup .................................................................................................................................... 57
6.3.3. Audio Setup ...................................................................................................................................... 59
6.3.4. Text Setup ......................................................................................................................................... 60
6.3.5. Serial Setup ...................................................................................................................................... 61
OSHD-410H & OSHD-810 & OSHD-1610
6.3.5.1. PTZ Setup ..................................................................................................................................... 61
6.4. Event Setup .............................................................................................................................................. 62
6.4.1. Event Check ...................................................................................................................................... 62
6.4.2. Sync Event ........................................................................................................................................ 62
6.4.2.1. Relay 1~4 ...................................................................................................................................... 63
6.4.2.2. Buzzer ........................................................................................................................................... 63
6.4.2.3. E-Mail Setup .................................................................................................................................. 63
6.4.2.4. FTP Image Backup ........................................................................................................................ 64
6.4.2.5. Twitter Synchronization ................................................................................................................. 65
6.4.3. Motion Detection ............................................................................................................................... 67
6.4.4. Sensor ............................................................................................................................................... 68
6.4.5. Preset ................................................................................................................................................ 68
6.5. Recording Setup ...................................................................................................................................... 68
6.5.1. Manual/Continuous/Schedule recording setup ................................................................................. 68
6.5.1.1. Manual Recording ......................................................................................................................... 69
6.5.1.2. Continuous Recording ................................................................................................................... 69
6.5.1.3. Schedule Recording ...................................................................................................................... 69
6.5.1.4. Event Recording Setup ................................................................................................................. 70
6.5.2. Program Setup .................................................................................................................................. 70
7. WEB VIEWER .............................................................................................................. 72
7.1. System requirement ................................................................................................................................. 72
7.2. Installation ................................................................................................................................................ 72
7.3. Login ........................................................................................................................................................ 72
7.4. User Setup ............................................................................................................................................... 72
7.5. Monitor ..................................................................................................................................................... 73
7.5.1. Screen division and changing video position .................................................................................... 73
7.5.2. Move to playback .............................................................................................................................. 74
7.5.3. Channel On/Off ................................................................................................................................. 74
7.5.4. Sensor Indication .............................................................................................................................. 74
7.5.5. Relay Operation ................................................................................................................................ 74
7.5.6. Using Microphone ............................................................................................................................. 75
7.5.7. Event information .............................................................................................................................. 75
7.5.8. Video Recording & Save ................................................................................................................... 75
7.5.8.1. Video Recording ............................................................................................................................ 75
7.5.8.2. Saving Video ................................................................................................................................. 76
7.5.9. Using PTZ ......................................................................................................................................... 76
7.5.10. Using Audio ................................................................................................................................... 77
7.6. Playback ................................................................................................................................................... 77
7.6.1. Video Division & Changing Channel ................................................................................................. 77
7.6.2. Image Saving .................................................................................................................................... 77
OSHD-410H & OSHD-810 & OSHD-1610
7.6.3. Print ................................................................................................................................................... 78
7.6.4. Back up ............................................................................................................................................. 78
7.6.5. Web Monitor Movement .................................................................................................................... 78
7.6.6. Channel On/Off ................................................................................................................................. 78
7.6.7. Saving time & Checking Rec, Capacity ............................................................................................ 79
7.6.8. Calendar Search ............................................................................................................................... 79
7.6.9. Function button under bottom of image ............................................................................................ 79
7.7. JAVA Viewer ............................................................................................................................................. 80
7.8. Mobile Viewer ........................................................................................................................................... 80
8. APPENDIX ................................................................................................................... 81
8.1. Trouble Shooting [FAQ] ............................................................................................................................ 81
8.2. Compatible HDD ...................................................................................................................................... 83
8.3. Compatible CD/DVD list ........................................................................................................................... 83
8.4. Factory Default ......................................................................................................................................... 84
8.4.1. Reset value for Recording Program ................................................................................................. 87
8.5. Menu Structure ......................................................................................................................................... 88
8.6. Specification ............................................................................................................................................. 90
8.7. Product Dimension ................................................................................................................................... 93
OSHD-410H & OSHD-810 & OSHD-1610
1. Key Features
FULL HD image supports
The product supports live monitoring and playback for HD-SDI high quality video of 1080p (1920x1080) / 720p (1280x720) resolution. Max 240 frames per second can be saved and Max 15 second recordable before event triggeres.
HD-SDI video record OSHD-410H model
o HD 1080p : 60fps o HD 720p : 120fps
OSHD-810 model
o HD 1080p : 120fps o HD 720p : 240fps
Supports manual & schedule recording Support archiving event list (Sensor, Video loss, Motion detection, Text) Available record Max 5 seconds before triggering an event per each channel
FULL HD high quality video will be able to show superior resolution compared with SD video product. Over 1200 TV lines at 1080p resolution can be visible.
SD
Full HD
D1 Resolution
1080P Resolution
720P Resolution
HD-SDI transmission
The product can transfer HD (High-Definition) signal image using HD-SDI technology via coax cable. Please be noted that this product doesn’t accept SD signal. The supportable resolution is as below.
Transmission method
o SMPTE 292M : HD-SDI
Resolution
o SMPTE 296M : 1280x720p 25/30/50/60Hz o SMPTE 274M : 1920x1080p 25/30Hz
Full HD : 1080p
HD : 720p
SD : D1
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 10
Monitoring screen
Supports real live video with high resolution per each channel and variable display mode. Also COVERT(hiding image) feature will secure privacy.
Various monitoring mode Single, Multi screen division Auto switching (Sequence) Event Popup Live/Playback 16 times (horizontal 16x, vertical 16x) digital zoom supports (D-Zoom)
Audio recording Supports real-time audio input and recording
Simultaneous 4ch audio input & recording available
Input : 4ch RCA, Output : 1ch RCA(Rear)
Simultaneous audio recording and playback available
Search / Playback
It supports variable and convenient functions for search & playback and FULL frame playback in 4 screen multi division.
QUAD Multi Full Frame playback Playback by time, Date, Channel Time/Calendar/Event/Thumbnail search Pre/Pose search from a freeze frame
Save and Backup
Internal HDD is supplied and image can be copied to DVD-R, CD-R, USB memory at user’s choice.
Various backup device supports : DVD-R, USB memory
HDD external unit (Expended external storage device) : Storage capacify extended via e-SATA HDD
or OSN-04ST
Network
It supports variable network like LAN, XDSL and easily control from remote site using web browser and customized CMS program.
HD Live monitoring/playback/backup from remote site
Multi-streaming feature for slow network environment (CIF/Half-D1/D1 monitoring)
Event information(Image) transmission using E-Mail/Twitter/FTP
Playback in PC, save, search and DVR configuration feature via CMS
Available to search, playback and backup from remote site
Customized Android, Iphone application
10/100Mbps Ethernet/xDSL support s
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 11
Max 1024 DVRs management
ETC
Supports User friendly GUI and mouse function
Easy and simple firmware upgrade by USB memory
Record data backup function thru USB
PTZ control, PRESET support
Available to control up to 16 DVRs with one remote controller
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 12
1.1. Accessories
Check if below items are included.
DVR
Remote Controller
Mouse
Battery
Rack Bracket & Screw
Screw for HDD installation
AC code
SW & Manual CD
Quick Guide
User’s Manual
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 13
1.2. Description & Function
1.2.1. Front
Category
Function
1
DVD-Multi for backup
Back up use for recorded data by DVD/CD media
2
Jog / shuttle
Playback direction change and speed control.
3
Touch channel button
Select channel by touch during live and playback.
Channel LED
Shows image input status and event working status.
4
REC
To start and stop Manual record
LOCK
To lock the buttons on the front panel/remote controller in monitoring status
5
ESC
To exit menu or close pop-up window
MENU
To enter Menu
6
Record LED
Display recording status
Event LED
Display event status when event is triggered.
Copy LED
Display copy status once copy is under process by flickering
Network LED
Display network connection status by flickering
Internal HDD LED
It flickers while internal HDD is recording
ExternalHDD LED
It flickers while eSATA HDD is recording
7
FUNC button
Runs FUNC menu where user can use main menu, screen division, auto sequence, copy, search, playback, keylock, logout, poweroff
SEAR button
Runs menu for search by time, calendar, event, thumbnail
COPY button
Runs menu for copy AVI, EXE thru DDVD, USB
RELAY button
Runs Relay On/Off manually
ZOOM button
Max 16 times zoon in live/playback screen and get into digital zoom mode
SEQ button
Runs Max 16 scenario of auto sequence in live mode
MULTI button
Changes division mode in live and playback mode
8
■(STOP)
Stop playback
◀l(SREW)
To move to reverse direction by one frame
◀◀(REW)
To move or select in menu and change replay speed to reverse direction in playback mode.
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 14
◀▶(PLAY)
To select playback mode and change playback direction.
▶▶(FWD)
To move or select in menu and change replay speed to forward direction in playback mode.
l▶(SFWD)
To move to forward direction by one frame
ll(PAUSE)
Pause playback
9
USB port
USB Memory, USB connection port
10
◀(Left move)
To move to left in menu
▶(Right move)
To move to right in menu.
▲(Upper move)
To move to upper in menu
▼(Down move)
To move to lower in menu.
Enter(select)
To select menu or enter the selected menu
11
Power
To turn On/Off power
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 15
1.2.2. Rear
2 3 4 5
7 8 9 10 1312 15
6
1411
1
No
In/Out port name
Function
1
Power connector
Socket for AC100V~AC240V power cord..
2
Sensor IN
Input for external sensor.
3
Relay
Relay Connection terminal.
4
Com2,3
RS-485 device connection
5
RS-485 termination
Set RS-485 termination
6
Ground
Ground between DVR & external device.
7
Channel input
BNC input for camera connection
8
Audio input(RCA)
RCA connection for Audio input
9
Audio output
Speaker output terminal.
10
Com1
RS-232C D-SUB..
11
VGA Output
Video output port to connect PC monitor.
12
HDMI Output
HDMI output port to connect PC monitor.
13
eSATA port
For eSATA external HDD connection
14
Storage
Connected to customized network storagee device(OSN-04ST) for use
15
Ethernet
For network connection (RJ-45)
1.2.3. Remote Controller
It is available to use all functions of DVR. If several DVR are set, each one can be set with unique ID number, they can be controlled with one remote controller. To use remote controller, it is necessary to set ID first. Keep pressing ID button repeatedly (Up to Max. 16 times) and use it matching DVR & ID.
(Refer to the picture for remote controller working angle)
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 16
MON REC
ID
Select Remote ID
COPY
Save record data into USB or CD/DVD
SEQ
Auto screen switch
MULTI
Screen division change
SELECT
No use
BACKUP
No use
MON
Change monitor
MENU
Change menu screen
ENTER
Select menu
Stop, Slow backward, Slow
forward, Pause
PTZ
Control PAN/TILT
LOAD PRESET
Lead PRESET
SAVE PRESET
Save PRESET
Search speed down, Reverse playback, Forward playback, Search speed up
EXIT
Cancel setup, get out of menu
Playback speed down, stop, playback/pause, playback speed up
HELP
Execute FUNC menu
RECORD
User record start or stop
+10
Select number over 10(+10 +1)
CHANNEL BUTTON
Select channel
ZOOM
Execute digital zoom
SEARCH
Display search menu
RELAY OFF
Alarm OFF manually
LOCK
Lock monitor screen
RELAY ON
Alarm ON manually
1.2.3.1. Remote Controller ID setup
MENU SYSTEM UTILITY
User can control multiple units with single remote controller by using different controller’s IDs. An ID can be set from 1~16 and to use all ID, please set ‘ALL’.
1.2.3.2. Select remote controller ID
Keep on pressing ID button of remote controller during 2 sec until there is BEEP sound to select DVR.
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 17
2. Installation
2.1. Before Installation
DVR is high quality security device having large capacity of HDD and important curcuits. So any high temperature occurred internally could make DVR work abnormally so please read through below installation advice before installation.
The followings are advice in case DVR is installed in the Rack.
1. Don’t keep inside of rack sealded where DVR is installed.
2. Keep airflow well thru inlet and outlet.
3. In case there is another device installed together, secure additional space and install air ventilation.
4. Installation of fan for air circulation is strongly recommended.
(Install filter around inlet or outlet for harmful substances)
5. Keep temperature around DVR as 0°C~40°C.
2.1.1. RACK installation
Engage rack brackets on both side of DVR using screw. Make sure to safely secure bracket and screws are place properly.
2.1.2. Caution for HDD installation
1. HDD is easy to get damaged even in small shock so please try not to give any shock on the HDD during
installation.
2. Be careful in handling cables not to take off insulated coat during installation.
3. Be careful not to lose screws and parts.
4. (In case screws and parts are not engaged well, products might not be working properly)
5. Check HDD compatible list before adding HDD.
6. (Please check with CS team for compatible list)
7. HDD used in PC or other DVR model must be re formatted and partition table should be deleted for re-use
in this product.
2.1.3. HDD installation
1. Loosen a bracket screw from DVR.
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 18
2. Push HDD bracket to the marked direction to separate it from fixed position.
3. Lift HDD bracket out of bottom of DVR.
4. Insert HDD into bracket and engate 4 screws to hold HDD.
5. Install HDD bracket with HDD into DVR then hold it with screw to fix it to the bottom part of DVR.
<Note> Socket arrangement of SATA cable in main b’d is as follows. Max 4ea HDDs can be installed in DVR.
Main b’d socket
Disk manager
J6
Int A
J7
Int B
J8
Int C
J9
Int D
2.1.4. Add HDD
User can install additional HDD. Make sure to take off power cord before installation to protect DVR against possible damage and expected electric shock.
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 19
Please refer to nearby vendor of the product from it was purchased from to know more about additional HDD installation.
◈ Note about data loss
Be aware of data damage of HDD. Check HDD compatibility before installing additional HDD. Be careful not to give any shock on HDD during operation which could lead to possible damage or malfunction.
◈ Case for damage on HDD and its data
To reduce damage coming from HDD damage, please copy data as often as you can. Data can be damaged while user take DVR off or any external shock on DVR during installation. DVR shut down due to power failure could damage HDD either. Please don’t move DVR while HDD is working.
2.2. Connecting other devices
2.2.1. Basic connections
2.2.1.1. Connecting monitor
Check resolution of monitor before connection.
HDMI port : 1920 x 1080p ( HDMI v1.2 Standard ) VGA port : 1920 x 1080p CVT-RB ( VESA Standard )
<Note>
Make sure to use standard camera supporting HD-SDI standard. (HD-SDI) Normal HDMI monitor and VGA monitor are not supported at the same time. In case monitor supporting both 1080p and 1920x1080p CVT-RB they can be connected and used at the same time.
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 20
2.2.1.2. Connecting camera
Connect DVR with HD-SDI cable using recommended coax cable. Input video type is recognized upon turning on DVR.
There is no limitation on same resolution cameras but in case 1080p and 720p are mixed to input, 720p must be connected on lower channel numbers while 1080p on higher number channel. e.g. No. 1,2 channel 720p connection / No. 3,4 channel 1080p connection / No. 5,6 channel 720p connection / No. 7,8 channel 1080p connection
Recommended cable
Cable type
HD-SDI transmission distance
Remark
5C2V
about 100M
Cable for analog signal
4C-FB(T), 4C-HFB(T), RG59
about 150M
High-foamed cable, double or trishield recommended
5C-FB(T), 5C-HFB(T), L-6CHD, RG6
about 200M
Customized for HD-SDI
<Note>
Transmission distance will be various based on reduction rate of 750MHz (reduction rate of
dB/100m < 25dB is recommended).
Foamed or high-foamed trishield cable is recommended. Please refer to KSC-3617,(5C-FBT), RG-6/U for recommended cable. Impedance 75Ω must be used for coax cable connection and connector work. Be ware of deformation of cable coming from high pressure over the cable. Don’t pull the cable by force. HD-SDI transmission length will be various based on cable manufacturer, installation environment.
2.2.1.3. Connecting power
When supplying power, DVR starts booting automatically. In order to cut off power, press power switch on DVR front during 5 seconds, then select “YES” after appearing a pop-up window. For supplying power again, push the Power button.
2.2.1.4. Connecting audio
Connect audio to DVR using RCA cable as following picture.
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 21
2.2.2. Connection map with other devices
2.2.3. Connecting external device
2.2.3.1. Connecting USB Device
USB port can be used for copy of recorded data and for mouse. USB Device spec will not be over following specification.
USB Spec.
Ver 2.0
Usable device
USB Memory Stick,
Voltage spec
Max. 200mA per DC 5V / Port
<Note> USB momory needs to be FAT32 formatted. USB Flash memory requires additional program on MS Windows could not be used in DVR.
2.2.3.2. Connecting eSATA Device
There is 1 port for external eSATA. Additional power for eSATA device will be required.
<Note>
1) Check compatibility of eSATA with DVR as not all eSATA might be compatible with DVR.
2) DVR might not be recognizing eSATA when eSATA is connected to DVR while DVR is working. So we recommend user to connect eSATA as following step.
3) Turn off DVR.
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 22
4) Turn off eSATA then connect it with DVR.
5) Turn of eSATA.
6) Turn on DVR.
2.2.4. Connecting OSN-04ST
2.2.4.1. Connecting OSN-04ST with DVR
(1) Connect OSN-04ST with DVR using Gigabit Ethernet Cable. (2) Connect OSN-04ST with DVR directly thru storage port of DVR.
<Note>
1) Network cable used should be Gigabit Ethernet Cable (Category-6). Otherwise connection will not be achieved.
2) Connect OSN-04ST with DVR directly using cable. In case there is hub between DVR and OSN-04ST, we can’t guarantee normal operation.
2.2.4.2. Set ID setup
Use Rotary Switch to setup ID. Different ID is required when over 2ea OSN-04ST are connected.
Use driver to setup ID value. 100x is for ID value for unit 100, 10x for ID value for unit 10, 1x for ID value for unit1. ID setup value must be between 2 ~254.
e.g.) 100x=1 , 10x=2 , 1x=3 setup means ID 123 of OSN-04ST.
<Note>
1) It takes around 1 minute for connection between DVR and OSN-04ST.
4ea LED in the front will be flickering while it tries connection. They will be all on (or off, flicker) after
connection is achieved and user can check HDD list in Disk Manager menu.
2.2.5. Connecting and configuring DIO ports
2.2.5.1. Wire handling
When connecting a wire to a terminal block, follow the instruction below. Not the different type of wire that can be used
Standard wire: Peel off the wiring cover 8~10mm and solder it. Wire gage should AWG 22~26. Sold wire: Peel off the wiring cover 8~10mm and solder it.Wire gage should be AWG 20~26.
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 23
2.2.5.2. Inserting & removing wire
To insert & remove wire in Terminal Block, use a screw driver in the diagram like below.
2.2.5.3. Connecting sensor
Spec
In order to run sensor input DVR normally, the following conditions are required.
Spec
Input Ch
4EA(8EA) Transistor input
Input type
N.C, N.O supprt
Supported sensor
Dry contact sensor
Way of connecting
Connecting the trimmed wire to terminal block
Performance
Available input pulse range
Minimum 500ms Output current
Typical DC 12mA
Connecting sensor input
Please refer to following picture for sensor input. The below picture is example of sensor connection having Dry Contact type. Please refer to “Wire Handling” for more information.
2.2.5.4. Connecting relay
Spec
In order to run relay output of DVR normally, the following conditions are required.
Spec
Output Ch.
4EA relay outputs
Output type
Dry contact
Connecting type
Connect the trimmed wire to terminal block
Performance
DC
30V 1A
AC
125V 0.5A
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 24
Connecting relay
Connect R1 ~ R4 with referring to the following images, it shows to connect a warning light. Please refer the “Wire Handling”
2.2.5.5. Connecting COM1 serial port with external devices
Text input device connection (ATM / POS / Access Control)
Using COM1/RS232, TEXT DATA can be recorded with synchronizing POS/ATM.
Like above picture, connect COM1/RS232 (9pin D-Sub) in Device menu and configure Serial and Text
2.2.5.6. Connecting COM2,3 serial port
Connecting Serial Port for Pan/Tilt/Zoom
If DVR supports thru. COM port, it is available to connect PTZ camera and control it. For a list of supported protocols, please refer to the list “Available PTZ list”. The following figure shows how to connect PTZ camera to RS485 (COM2/COM3). When using another serial port, connect it with referring to each connection diagram below. Please refer the “Wire Handling”.
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 25
Connecting Serial Port for Transparent device
This is function to support direct connection between serial port of PC and COM port of DVR and this is for development of Application throughout SDK. This is not used in general case so please contact customer service for more details about this function
Serial communication port diagram
<Note>
Single device connection per each COM port is recommended. To connect multi devices to single port requires specialized knowledge and without this, it could lead to malfunction of device. Single serial port can have one PTZ protocol so PTZ protocol can be set in Serial Port menu and PTZ address can be set in camera menu.
Text Device Keyboard Device
COM1
RXD
TXD
GND
TX RX
GND
Keyboard Device Dome Camera PTZ Receiver
COM2 COM3
TR+ TR-
GND
TR+ TR-
TR+ TR-
GND
TR+ TR-
2.2.5.7. Configuring an extension of PTZ & Keybaord
It is available to connect up to 255 DVR using keyboard controlling all buttons of DVR & channels which are connected with PTZ. Also, multiple keyboards extension as Slave can be used limitless with Master Keyboard. In ths case, Master Keyboard has priority for all controls. Please refer the instruction manual for PTZ keyboard connection & its way of control which comes with PTZ/ Keyboard.
Confituration using 2 serial ports
In case user use 2 serial ports, user can control PTZ(DOME) using Keyboard by connecting PTZ(DOME) and Keyboard device to COM2 and COM3.
The below diagram represents configuration of multi DVRs with PTZ(DOME). To control PTZ(DOME) using keyboard, please select DVR ID then select camera for control.
Control device
Connection device
Keyboard (Master/Slave)
All DVRs can be controlled, All PTZ(DOME) can be controlled
DVR
PTZ(DOME) directly connected to DVR can be controlled
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 26
Slave 1
Serial Cable Video Cable
Slave 2
Slave 255
Master
DVR 255
DVR 1
DVR 2
DVR 3
DOME 1 DOME 2 DOME 16
DOME 1 DOME 2 DOME 16
DOME 1 DOME 2 DOME 16
DOME 1 DOME 2 DOME 16
COM2 COM3
Confituration using 1 serial ports
In case user use 1 serial port, user can connect either of PTZ(DOME) or Keyboard to one of COM2 or COM3 so user can select PTZ(DOME) throughout keyboard. And user can select controllable connection device based on COM port setup of DVR. User can also control DVR individually by selecting DVR ID from keyboard.
In case PTZ(DOME) is setup on DVR COM port user can use it as following method.
Control device
Connection device
Keyboard (Master/Slave)
All DVRs can’t be controlled/ All PTZ(DOME) can be controlled
DVR
Only PTZ(DOME) directly connected to DVR can be controlled
In case Keyboard is setup on DVR COM port user can use it as following method.
Control device
Connection device
Keyboard (Master/Slave)
All DVRs can be controlled, All PTZ(DOME) can be controlled
DVR
All PTZ(DOME) can’t be controlled
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 27
3. Menu Usage
3.1. Menu Structure
The menu structure will be shown like below image, and each menu setting method is described in explanation of set items.
Date/Time Disk User Setup Utility
Network xDSL WRS Radius
Camera Monitor Audio Text Serial
Event Motion Sensor Preset
Record Program
3.2. Function Menu
To run Function menu, please, click the right button of mouse
in live monitoring or playback status or push “Func” button on
the front panel. The Function menu can be controlled by mouse. Each function can be executed by clicking right button of mouse and click desired icon. The Function menu also can be controlled by front part of DVR’s buttons. Please refer to below picture for the Function menu structure. Please be noted that Function menu will disappear if there is no operation during 20 seconds.
Function menu in live screen
Function menu in playback screen
3.3. Factory Reset
System Setting System Setting
In order to reset value to factory value, go to System Setting System Setting, and once press Factory Reset then the warning message will be appear, click “Yes” to reset the DVR value to factory.
OSHD-410H & OSHD-810 & OSHD-1610
Install & User Manual - Firmware 3.X 28
3.4. OSD menu configuration
Press [MENU] in keypad of front to open the main menu;
3.4.1. Menu structure
Press [MENU] key in front panel or press [Main Menu] button to get into setup menu.
(1) Main menu: The selected tab is shown in bright color and the related sub-menu will be shown left- below the tab. To move to the previous/next tab, use the [◀/▶] arrow buttons. To move to a sub-menu press the [Enter] key or click the mouse button when you use mouse. (2) Sub-menu : Selected sub-menu is shown as tab title and the related setting will be shown. To move to the previous/next tab, use the [◀/▶▲/▼] arrow buttons. To move to the related setting press [Enter] or click the mouse. To move to upper main menu, press [ESC] button.
(3) Setting page: The selected tab is shown as orange, To move to the previous/next tab, use the [◀/▶] or [▲/▼] arrow button or click the mouse. To configuration setting, press [Enter] key for value setting or click the mouse. When setting value is a word, a dialogue box to edit the word will be open. When setting value is number, it should be set with using [◀/▶] or [▲/▼] or click the related numbers by mouse. Press [ESC] button or click [Enter] by mouse when the value is set. Also [ESC] button or click the mouse is available to upper sub­menu.
Dialogue box to edit a word Dialogue box to edit a word is image shown as below; It is available to input both word and Number.
Main menu
Sub menu
Setup dialog box
Loading...
+ 66 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use