Orion OR-S7020i, OR-S7030i User Manual

H.264 Network Camera

User Manual

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with a dry cloth.

7) Do not block any of the ventilation openings. Install in accordance with the manufacturer's
instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
that produce heat.

9) Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

10) Only use the attachments/accessories specified by the manufacturer.

11) Use only with a cart, stand, tripod, bracket,

or table specified by the manufacturer,
or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.

12) Unplug this apparatus during lightning storms or when unused for long periods of time.

13) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged

in any way, such as power supply cord or plug damage, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.

Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do
not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

In USA and Canada, Use Class 2 Power Supply Only

This product was tested with a UPS to satisfy EN 61000-4-11 test conditions (voltage dips and short interruptions test)

under the EN 50130-4: 2011 standard.

Contents

1. Product Features ........................................................................................................................... 4

2. Accessing the Camera ................................................................................................................... 14

2.1 Access from a Browser ............................................................................................................. 14

2.2 Accessing the IP Camera from the Internet .................................................................................. 14

2.3 Adjusting the Image ................................................................................................................. 14

2.4 Live View ................................................................................................................................ 15

2.5 Video Stream Types ................................................................................................................. 16

2.6 How to Stream H.264 ............................................................................................................... 16

3. Setup .......................................................................................................................................... 17

3.1 Analog Output ......................................................................................................................... 17

3.2 Video ..................................................................................................................................... 17

3.2.1 Codec ............................................................................................................................. 17

3.2.2 Camera ............................................................................................................................ 19

3.3 Audio ..................................................................................................................................... 20

3.4 Live ........................................................................................................................................ 21

3.4.1 Setup .............................................................................................................................. 21

3.4.2 Privacy Mask .................................................................................................................... 21

3.5 SD Card .................................................................................................................................. 22

3.5.1 Config ............................................................................................................................. 22

3.5.2 Event ............................................................................................................................... 23

3.5.3 Periodical ......................................................................................................................... 24

3.6 FTP ........................................................................................................................................ 25

3.6.1 Config ............................................................................................................................. 25

3.6.2 Event ............................................................................................................................... 26

3.6.3 Periodical ......................................................................................................................... 27

3.7 Event ..................................................................................................................................... 27

3.7.1 Alarm Port ........................................................................................................................ 27

3.7.2 Motion ............................................................................................................................. 28

3.7.3 Mapping ........................................................................................................................... 28

3.8 Network .................................................................................................................................. 29

3.8.1 IP Setup ........................................................................................................................... 29

3.8.2 Service Port ...................................................................................................................... 30

3.8.3 RTP ................................................................................................................................. 31

3.8.4 E-mail ............................................................................................................................. 32

3.8.5 DDNS .............................................................................................................................. 33

3.8.6 UPnP ............................................................................................................................... 33

3.9 PTZ ........................................................................................................................................ 34

3.9.1 Preset .............................................................................................................................. 34

3.9.2 Preset .............................................................................................................................. 35

3.9.3 Scan ............................................................................................................................... 36

3.9.4 Tour ................................................................................................................................ 36

3.9 System ................................................................................................................................... 37

3.9.1 User ................................................................................................................................ 37

3.9.2 Date/Time ........................................................................................................................ 37

3.9.3 Maintenance ..................................................................................................................... 38

3.9.4 Information ....................................................................................................................... 38

4. Accessory List .............................................................................................................................. 39

1. Product Features

Part Names and Descriptions

- Outdoor Model

⑩

Video output
for service monitor

⑨Micro SD card slot

(SDHC Supported)

⑥Alarm In

⑤

Alarm Out

④Power

⑧Reset Button

①

②Audio In (Black)

③

Audio Out (White)

- Indoor Model

⑦

Status LED

Network

⑩

Video output
for service monitor

⑨Micro SD card slot

(SDHC Supported)

⑥Alarm In

⑤

Alarm Out

④Power

⑦

Status LED

⑧Reset Button

①

Network

②Audio In (Black)

③

Audio Out (White)

1.

Network connector

The PTZ Camera series connects to the network via a standard network cable,
and automatically detects the speed of the local network segment (10BaseT/100BaseTX Ethernet).
This socket must be used to power the PTZ Camera series via Power over Ethernet (PoE).
The camera auto-senses the correct power level when using a PoE(IEEE802.3at) switch, router or injector.

*A ferrite core accessory is included to be used when connecting the network cable in order to suppress

electromagnetic waves.

2.

Audio in

Audio in (line level), for line-in mono signal (only left channel is used from a stereo signal)

3.

Audio out

The Audio output (line level), which coul d be connected to a line output of an active speaker with a built-in
amplifier.

4.

Power Connector

24VAC power connector

5.

Alarm out

Two relay output (2A: AC120V / DC24V)

COM (Alarm Out 2)
Alarm Out 2
COM (Alarm Out 1)
Alarm Out 1

6.

Alarm In

Two analog (dry contact) alarm input

COM (Alarm In 2)
Alarm In 2
COM (Alarm In 1)
Alarm In 1

LED

Color

Indication System Status

Network

Green

On

Connection to 10/100Mbps Network / LAN.

Flash

Indication of network activity.

Unlit

No network connection established.

Status

Red

On Camera is booting up.

Flash

Firmware Upload in progress.

7.

Status LED

8.

Reset Button

Press this button to restore the ca mera configuration to its factory default settings.

9.

Micro SD card

Save snapshot images onto a Micro SD card.

10.

Video Output for Service monitor

This analog video output is available when installation mode is set to ON. Use accessory cable to video output.

Outdoor Model Installation Method

Hex Screw M4X15 (X2)

Mount Adaptor

Silica Gel

1.

Remove the two hex screws and twist to remove the mount
adapter.

2.

Turn the mount adaptor counter clockwise to
remove from product.

1. Attach the included silica gel accessory to inner dome with

double-sided tape.

Wall Installation: Wall Mount

Wall Mount Bracket (Option)

Mount Adaptor

Gasket Wall Mount

Anchor Bolt (X4)

1.

Affix the wall mount bracket to the wall with anchor bolts.

2.

Place mount adaptor in wall mount bracket, rotate clockwise,

and tighten with screws.

Dome Safety Wire

3.
the body and tighten clockwise with hex screws.

4.

Align housing safety wire to product hooks, connect cables, and align mount adapter with

Connect dome safety wire and secure dome cover.

Hex Screw M4X15 (X2)

Housing Safety Wire

Alignment Mark

Hex Screw M4X20 (X4)

Dome Cover

Ceiling Pendant Installation: Ceiling Mount

Ceiling Mount Bracket (Option)

Mount Adaptor

Anchor Bolt(X4)

Gasket Ceiling Mount

1. Affix the ceiling mount bracket to the wall with anchor bolts.

2. Place mount adaptor in ceiling mount bracket, rotate clockwise,
and tighten with screws.

Hex Screw M4X15 (X2)

Housing Safety Wire

Dome Safety Wire

Alignment Mark

]

Hex Screw M4X20 (X4)

Dome Cover

3. Align housing safety wire to product hooks, connect cables, and align mount adapter with
the body and tighten clockwise with hex screws.

4. Connect dome safety wire and secure dome cover.

In-Ceiling Installation: In-ceiling Mount (Indoor)

Safety wire

Mounting wing

1. Drill a hole in the ceiling (Ø170mm). Connect safety wire to hook on module to secure camera.

2. Turn three mounting wing screws clockwise to secure product.

Mounting wing Screw (X3)

Tapping Screw (X2)

Dome Cover

3. Secure tapping screws to prevent product movement.

4. Insert dome cover and twist clockwise to secure.

2. Accessing the Camera

 Follow the instructions in the IP Camera Installation Guide to install the camera. This IP Camera can be

accessed on most standard operating systems and web browsers. For the best performance, Windows 7
and Internet Explorer 9 (32bit) is recommended.

2.1 Access from a Browser

1. Open a web browser (Internet Explorer 9 32 bit recommended).

2. Enter the IP address or host name of the IP Camera in the Location/Address field of the browser and
press Enter.

3. A dialog box will pop up to Log-In. The default user name is ADMIN and the default password is

1234.

4. The IP Camera’s Live View will now be displayed on the web browser.
Note: The layout of the live view page for the IP Camera may have been customized to meet specific requirements.
Consequently, some of the examples and functions featured here may differ from a user’s experience.

2.2 Accessing the IP Camera from the Internet

 Once installed, the IP Camera is accessible on the Local Area Network (LAN). Configure the

router/firewall to allow incoming data traffic to access the IP Camera from the Internet. For security
reasons, this is usually done through a specific port. Please refer to the router/firewall documentation for
further information and instructions.

2.3 Adjusting the Image

 To adjust the position of the lens:

1. Open the Live View page in a web browser. Select the Setup tab and open the Installation page.

Select Video Format.

2. Connect an analog monitor to the Video Out with a BNC cable. Use the image to confirm the

camera is position properly.

3. Check and confirm the image is set as desired on the Lenz Adjustment in Live View page.

2.4 Live View

PC(Client) Speaker

PC(Client) Microphone

Digital Zoom

Snap Shot

Full Screen

Video Stream change: First stream  Second stream

Play: Click this button by manually to start the stream

Stop: Click this button by manually to stop streaming

NOTE: It is possible that not all the buttons described below will be visible unless the Live View page has been
customized to display them.

2.5 Video Stream Types

 H.264 Protocols and Communication Methods:

o Real-time Transport Protocol (RTP): RTP is a protocol that allows programs to manage the real-

time transmission of multimedia data, via unicast or multicast.

o Real Time Streaming Protocol (RTSP): RTSP serves as a control protocol to negotiate the type of

transport protocol to use for the stream. RTSP is used by a viewing client to start a unicast session.

o User Datagram Protocol (UDP): UDP is a communications protocol that offers limited service for

exchanging data in a network that uses the Internet Protocol (IP). UDP is an alternative to the
Transmission Control Protocol (TCP). The advantage of UDP is that it is not required to deliver all
data and may drop network packets when there is network congestion. This is suitable for live video
as there is no point in re-transmitting old information that will not be displayed anyway.

o Unicasting: Unicasting is communication between a single sender and a single receiver over a

network. This means that the video stream goes independently to each user and each user gets a
personal stream. A benefit of unicasting is if one stream fails it only affects one user.

o Multicasting: Multicasting is a bandwidth-conserving technology that reduces bandwidth usage by

simultaneously delivering a single stream of information to multiple network recipients. This
technology is used primarily on delimited networks (intranets) as each user needs an uninterrupted
data flow and should not rely on network routers.

2.6 How to Stream H.264

 Deciding on the combination of protocols and methods to use depends on user viewing requirements a

local network properties. Setting the preferred method(s) is done on the Setup page.

o RTP+RTSP: This method (actually RTP over UDP and RTSP over TCP) should be the first

consideration for live video, especially when it is important to always have an up-to-date video
stream, even if some of the images are lost due to network problems. This can be configured as
unicast or multicast.

o RTP/RTSP/Multicasting: This provides the most efficient use of bandwidth, especially when there

are large numbers of clients connecting simultaneously. Note, however, that a multicast broadcast
cannot pass a network router unless the router is configured to allow this. For example, it is
impossible to multicast over the Internet.

o RTP/RTSP/Unicasting: This should be used for video-on-demand broadcasting so that there is no

video traffic on the network until a client connects and requests the stream. However, as more and
more unicasts clients connect, the traffic on the network will increase and may cause congestion.
Although there is a maximum of 8 unicast viewers, note that all multicast viewers combined count
as 1 unicast viewer.

o RTP/RTSP: This unicast method is RTP tunneled over RTSP. This could be used to exploit the fact

that it is relatively simple to configure firewalls to allow RTSP traffic.

3. Setup

 Administrators with unrestricted access can configure the IP Camera in the web browser through the

Setup tab.

3.1 Analog Output

 Toggle the Analog Output ON to connect via BNC output or toggle OFF and click SAVE.

[Not all IP Cameras have an Analog Output]

3.2 Video

3.2.1 Codec

 These are tools to control the camera network streams, adjust network stream video quality settings,

and control the video bit rate.

o Codec: H.264 and MJPEG are supported. Both streams cannot be set to MJPEG. Note that

NONE is also a selection for the 2nd Stream.

 H.264 is a video compression standard that makes good use of bandwidth and which

can provide high-quality video streams at less than 1 Mbit/s. The H.264 standard
provides scope for a large range of different coding tools for use by various
applications in different situations, and the IP Camera provides certain subsets of
these tools. Using H.264, it is also possible to control the bit rate, which in turn
allows the amount of bandwidth usage to be controlled.

o Size: Video output resolution.
o Frame Rate (FPS): Choose the number of image frames per second, from 1-30fps in

normal mode or 1-15fps when slow shutter mode is enabled. If slow shutter mode is enabled
and the low light condition is met, the frame rate automatically goes down to half of the
normal mode setting.

o GOP Size: The GOP Size can be set from 1-60 frames.
o Bit-rate Control: When using H.264 compression, if there is only a limited amount of

bandwidth available a constant bit-rate (CBR) is recommended, although this may
compromise image quality. Use a variable bit-rate (VBR) for the best possible image quality.

o Average Bit-rate: Can be set from 512Kbps-10Mbps.

 Recommended bit-rate for D1: 800Kbps-1Mbps
 Recommended bit-rate for 1.3M (720p): 3Mpbs-4Mbps
 Recommended bit-rate for 2M (1080p): 6Mbps-8Mbps

o MJPEG Quality: If a stream is set to use the MJPEG compression codec, the quality of the

MJPEG codec can be set from 1-100, where 100 is the highest quality.

o Boost Quality: If Boost Quality is set to ON, the Boost FPS and Boost GOP Size can be set.

If there is motion in the camera’s field, the image quality will increase using these settings.

o Anti-Flicker Mode: Set to 60Hz for NTSC, or 50Hz for PAL. For usage when the camera is

installed in locations lit by fluorescent lighting.

o Video Mirroring: Choose NONE for no video mirroring, HORIZONTAL for horizontal

video mirroring, VERTICAL for vertical video mirroring, or FLIP for horizontal and vertical
video mirroring.

o Bandwidth Limit: If set to ON, the maximum bandwidth can be set from 1000Kbps-30Mbps.

3.2.2 Camera

 This section allows various camera settings to be adjusted.

o Exposure Control:

 Exposure Mode: Set to AUTO for automatic exposure control, or MANUAL to

control the camera exposure manually.

 AGC Gain: If Exposure Mode is set to MANUAL, AGC Gain can be set from 0-

28dB. For low light conditions, adjust to a higher value.

 e-Shutter Speed: If Exposure Mode is set to MANUAL, e-Shutter Speed can be set

from 1/30-1/10000.

 Slow Shutter: Can be turned on for low light conditions; can be set to x2, x4, or x8.
 MAX AGC: Max Automatic Gain Control can be set to LOW, or HIGH.
 BLC Control: Back Light Compensation control. This adjusts the exposure of

scenes with strong backlight in the center-bottom of the image. When the image
background is too bright or the subject is too dark, backlight compensation makes the
subject appear clearer. The settings for low light behavior determine how the camera
behaves at low light levels. These settings affect video image quality and how much
noise is in the images. This can be set to ON, or OFF.

 WDR: Wide Dynamic Range (WDR) is a feature that allows for different objects at

different exposures to be viewed in the same scene (ex; one object in a bright area
and one in a dark area). When WDR is activated the FPS setting will automatically
drop by fifty percent. ON(Histogram): The video image is analyzed via histogram to

gradually adjust the exposure between bright and dark areas. Auto(Low Detection):
Only used when the difference between bright and dark areas is severe. Auto(Middle
Detection): Used when the difference falls under normal levels. Auto(High
Detection): WDR will automatically activate even when the difference between
bright and dark areas isn't severe.

 Day/Night Mode: If set to AUTO, the camera will automatically switch according to

current lighting conditions that persist for a set period of time. The mode can also be
set to specifically DAY or NIGHT, as well as SCHEDULE.

o White Balance Control:

 WB Mode: Can be set to MANUAL, or AUTO. This is used to make the colors in

the image appear consistent, compensating for the different colors present in different
light sources. The IP Camera can be set to automatically identify the light source and
compensate accordingly.

 MWB Mode: If white balance is set to MANUAL, the light source can be manually

added, such as INDOOR (3200K), or OUTDOOR (5800K).

o Image Property Control:

 Sharpness: Modifies the video signal sharpness. Default: 8, Range: 1-15
 Brightness: Modifies the video signal brightness. Default: 12, Range: 0-30
 Contrast: Modifies the video signal contrast. Default: 18, Range: 0-30
 Color: Modifies the video signal color. Default: 7, Range: 0-30

o Focus Control:

 Focus Mode: Focus Mode can be set to Auto, Auto-Semi, and Manual. MANUAL :

User manually focuses the lens. AUTO: The camera will automatically focus the
lens. AUTO(semi): Camera will automatically focus one time when user controls the
PTZ camera. After the PTZ operation is complete the camera will not refocus in
accordance to change in luminance or position.

 Focus Near Limit: Focus can be set to be restricted to a distance within the set

focus value. This can be set to 100CM, or 30CM.

3.3 Audio

 Choose to enable or disable the audio function, which uses the G.711 u-law codec at 8 KHz. The

microphone and speaker volume can also be adjusted.

3.4 Live

3.4.1 Setup

 This section allows for general viewer settings to be adjusted.

o Viewer Setup:

 LiveView Protocol: Choose which protocol to use for live video. RTP Unicast

(UDP), RTP Multicast (UDP), or RTP over RTSP (TCP) can be selected.

 Buffering Time: Buffering time can be set for a number between 0-90 times 1/30

seconds, or a range of 1-3 seconds.

o Viewer OSD Setup:

 Resolution: Toggle OSD Resolution ON/OFF.
 Date/Time: Toggle OSD Date/Time ON/OFF.
 Event State: Toggle OSD Event State ON/OFF.

3.4.2 Privacy Mask

 The IP Camera can support the privacy mask feature so a portion of the frame can be blocked based on

personal preference of legal requirements. Select the Area and Color and click Save.

3.5 SD Card

3.5.1 Config

 This section is provided to set up an SD Card for recording images.

o SD Card Configuration:

 Overwriting: Enable or Disable the SD Card function for recording images.
 SD Status: Check the status of the SD Card.
 SD Safety Remove: Unmount any SD Card before removal and mount when

inserting an SD Card.

 Erase Image Files: Delete image files on the SD Card.

3.5.2 Event

 This page is for configuring whether or not to write images to an SD card when an event occurs.

o Event SD Writing:

 SD Writing: Choose whether to Enable or Disable this function.
 Directory: Input the desired file path on the SD Card for the uploaded images.
 File Prefix: Input the desired file name prefix (for example, alm_).
 SD Write Mapping: Choose whether to write images during Alarm In, and/or

Motion.

 Effective Period: Choose whether to always write images when an event occurs or

during a user-defined schedule.

3.5.3 Periodical

 This page is for configuring whether or not to periodically write images from the camera to an SD card.

o Periodical SD Writing:

 SD Writing: Choose whether to Enable or Disable this function.
 Directory: Input the desired file path on the SD Card for the uploaded images.
 File Prefix: Input the desired file name prefix (for example, per_).
 Interval: Choose the desired image write interval, from 10 seconds to 1 hour.
 Effective Period: Choose whether to always write images when an event occurs or

during a user-defined schedule.

3.6 FTP

3.6.1 Config

 This section is provided to set-up a FTP (File Transfer Protocol) server so the IP Camera can send

recorded images to the server.

o Server Configuration:

 FTP Server: Enable or Disable the FTP Server function for downloading recorded

images.

o Client Configuration:

 Server IP: Enter the desired FTP Server’s IP address.
 Port: Enter the desired FTP Server’s Port number. Default: 21, Range 1025-65535.
 User name: Enter the FTP Server client user name.
 Password: Enter the FTP Server client password
 Send Mode: Choose whether the send mode is Active or Passive.

3.6.2 Event

 This page is for configuring whether or not to send images to an FTP server when an event occurs.

o Event FTP Sending:

 FTP Sending: Choose whether to Enable or Disable this function.
 Directory: Input the desired file path on the FTP server for the uploaded images.
 File Prefix: Input the desired file name prefix (for example, alm_).
 FTP Send Mapping: Choose whether to write images during Alarm In, and/or

Motion.

 Effective Period: Choose whether to always upload images when an event occurs or

during a user-defined schedule.

3.6.3 Periodical

 This page is for configuring whether or not to periodically upload images from the camera to an FTP

server.

o Periodical FTP Sending:

 FTP Sending: Choose whether to Enable or Disable this function.
 Directory: Input the desired file path on the FTP server for the uploaded images.
 File Prefix: Input the desired file name prefix (for example, per_).
 Interval: Choose the desired image upload interval, from 10 seconds to 1 hour.
 Effective Period: Choose whether to always upload images when an event occurs or

during a user-defined schedule.

3.7 Event

3.7.1 Alarm Port

 This page is designed to allow for enabling/disabling the IP Camera’s Alarm Input/Output.

3.7.2 Motion

 This page is designed to allow for different motion areas to be selected and saved. Select an area and

use the mouse to click and drag the desired area, then click Save.

3.7.3 Mapping

 This page is designed to allow a user to select whether or not to have an e-mail notification sent to

specified users if Alarm In or motion event occurs.

3.8 Network

3.8.1 IP Setup

 This page allows for current network settings to be configured, specifically the IP Camera’s IP address.

The IP Camera supports IP version 4, which allows the IP address to be set automatically via DHCP
(Dynamic Host Configuration Protocol) or manually via a Static IP address. DNS (Domain Name
Service) configuration provides the translation of host names to IP addresses on the network. If the
DHCP server can update the DNS server, it is possible to access the IP Camera by a host name which is
always the same, regardless of the IP address. The 1st DNS is the IP address of the primary DNS server
on the network and the 2nd DNS is the IP address of the secondary DNS server, which is used if the
primary DNS server is unavailable.

 By default, the IP Camera is set to get the IP address from the DHCP server and UPnP is enabled. If the

network has a DHCP server and the UPnP function is enabled on a PC, it is possible to find the IP
Camera in “My Network”.

 If a DHCP server is not available on the network, please assign the IP address as follows:

o Execute Admintool.exe and click the ‘Search’ button.
o Select the camera after it appears in the camera list.
o Type in all of the network information.
o Click the ‘Apply’ button and the settings will appear in the list.
o Click the ‘Setting’ button to set network information for the IP Camera.

 When you double-click the camera in the list, the default web browser (Internet Explorer or compatible

equivalent) will open and automatically connect to the IP Camera.

3.8.2 Service Port

 This page is for setting the IP Camera port numbers.

o Service Port:

 HTTP Port: Input a desired HTTP (Hyper Text Transfer Protocol port number).
 RTSP Port: Input a desired RTSP (Real Time Streaming Protocol port number).

o Port Forwarding:

 Port Forwarding: Select AUTO to automatically set the connection ports of the

router. Note: UPnP must be supported by the router.

 External IP: If Port Forwarding is successful, the external IP address for the IP

Camera will be displayed. This is the address that can be used to access the IP
Camera.

3.8.3 RTP

 This page is for defining RTP (Real-Time Transport Protocol) settings for the IP Camera. RTP is used

for delivering audio and video over an IP network, including multiple destinations through multicast.

o RTP Port Range:

 Start Port: Enter the desired Start Port number.
 End Port: Enter the desired End Port number.

o Multicast Setup:

 Enter the IP addresses, Video Port numbers (even values only), Audio Port numbers

(even values only), and TTL values for each stream.

3.8.4 E-mail

 This page allows users to toggle e-mail notification and specify which e-mail server is used. By default,

a user can toggle notifications on and the default e-mail server will function without further setting
required.

o E-mail Setup:

 Notification: Toggle e-mail notification ON/OFF.
 Frequency: Select the frequency of e-mail notifications. Range: 1-60 minutes.
 Server: If not using the default server, input the address of the desired server.
 Port: If not using the default server, input the SMTP port number of the desired

server. Default value: 25

 Security: Toggle SSL or TLS security ON/OFF.
 User: If not using the default server, input the user name for accessing the e-mail

server.

 Password: If not using the default server, input the user password for accessing the

e-mail server.

 From: Input the name that will display before the e-mail address when receiving a

notification.

3.8.5 DDNS

 This page allows a user to enable or disable DDNS (Dynamic Domain Name System) and select an

address to be used for connecting to the IP Camera.

o DDNS Setup:

 DDNS: Toggle DDNS ON/OFF.
 User Set URL: Input a domain name to connect to the IP Camera (for example,

http://ipcamera.dvrlink.net)

3.8.6 UPnP

 This page is for toggling UPnP (Universal Plug and Play) on or off. It is ON by default.

3.9 PTZ

3.9.1 Preset

 General PTZ functions can be setup on this page.

o Preset Freeze: Freeze video before moving to Preset and resume after Preset movement

completed.

o Power Up Action: Automatically continue from Scan/Tour from prior operation if unit

completes booting action.

o Parking Action: Run the specified action after a user-specified period of time when there are

no Pan, Tilt, Zoom operations.

o Wait Time: Wait Time is the waiting time before engaging Parking Action when PTZ is not in

operation.

o PTZ Action: Action is executed after a set wait time.

 Preset Select: Select Preset to run.
 Latest Action: Run most recent action.

3.9.2 Preset

 Preset is a pre-defined camera view than can be quickly and easily moved to and

viewed, simply by selecting the preset.

o Preset: select preset Number.
o Name: Input preset Name.
o Show Advanced: Day/Night Focus Setup windows pops up.
o Save: Specified value Saved.
o Move: Run preset.
o Delete: Specified value Deleted.
o Delete All: All Preset value Deleted.

3.9.3 Scan

 Scan displays the video stream from different preset positions.

o Name: Up to 15 characters can be used to set a Scan name.
o Number: 1-12 can be set (no duplication)
o Speed: Preset interval movement speed.
o Dwell Time: The waiting time between moving to the next Preset.
o Preset: Can select one from previously set Presets. Preset1(From) / Preset2(To)
o Direction: The direction of Scan movement can be set.AUTO, CW or CCW
o Add/Del: Press the Add button to add new Scans or Delete to delete Scans (must click Save to

apply).

o Run: Run Scan.

3.9.4 Tour

 Set the camera movement. Preset, Scan, and Tour can be selected to fulfill

one entire Tour.

o Tour Speed: Sequence movement speed.
o Sequence: Consists of Sequence members (Preset, Scan, Tour) and Dwell Time.

3.9 System

3.9.1 User

 This page is for user management: adding new User IDs within a specific group and specifying the

user’s password, e-mail address, and whether or not the user should receive e-mail notifications. A user
may also be deleted. The Admin group allows users to change settings and view live streaming video.
The User group only allows users to view live streaming video.

3.9.2 Date/Time

 This page configures the IP Camera date and time settings.

o Date/Time Setup:

 Current Server Time: This displays the IP Camera’s current system time and date.
 Date Format: This allows the display format for the date to be changed.
 Time Format: This allows for the display format for the time to be changed between

12 hour and 24 hour timekeeping systems.

 NTP Server: If ‘Synchronize with NTP server’ is selected, input the NTP server

address.

 Local Time: If ‘User set manually’ is selected, input the time manually or sync with

a PC.

 Time Zone: Select the IP Camera’s time zone.
 DST: Toggle Daylight Savings Time ON/OFF.

3.9.3 Maintenance

 This page is for important system maintenance for the IP Camera.

o Maintenance:

 System Name: Input the desired name for the IP Camera.
 System Reboot: Reboots the IP Camera if clicked.
 Factory Default: Resets all IP Camera settings to original factory settings if clicked.
 Save/Load PTZ Data: PTZ Setup Status (Preset, Scan, Tour…) Save or Load.
 Enable Firmware Upgrade: Must be clicked prior to performing a firmware

upgrade.

 Firmware Updates: Browse the network directory for a firmware file and press OK

to update the IP Camera firmware.

3.9.4 Information

 This page displays some important information about the IP Camera.

Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the security

or signaling aspects of this product.

UL has only tested for fire, shock or casualty hazards as outlined in UL’s Standard(s) for Safety,

UL60065.

UL Certification does not cover the performance or reliability of the security or signaling aspects
of this product.

UL MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS WHATSOEVER
REGARDING

THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED
FUNCTIONS OF THIS PRODUCT.

The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the apparatus
"WARNING: To Reduce the Risk of Fire or Electric Shock, Do Not Expose This Apparatus to
Rain or Moisture"

4. Accessory List

Accessory List

Item

Description

IP Camera

IP PTZ Camera, 1EA

CD

User Manual CD, including product documentation, installation tools, and other
software

Printed Installation Guide

Quick Guide for installation

Accessories

Silica gel (Out Door Only)
Safety Wire(In Door Only)
Carabineer(In Door Only)
Ferrite Core
Wrench (Hex 2.5mm) (Out Door Only)
Power Terminal Block
Analog Video Cable
Alarm Cut Cable
Alarm In Cable