Page 1
VANDAL-PROOF & WATERPROOF
3-AXIS DOME CAMERA
GST-410
MANUAL
◐ HOW TO INSTALL
1. Camera installa tion
<Ceiling mount>
<Wall mou nt>
(1) Fix the camera set with the supplied screws on ceiling or wall
mount. If you don't use supplied screws, the camera may fall off.
(2) Please refer to '3. Camera angle adjustment' regarding adjust
camera angle.
(3) Lens a djustment(Vari-focal Lens on ly)
① By turning the "Tele-Wide" knob,
you cana ccess a range of focal
lengthswithin specified limits.
② Since then, by turning the "Near-Far"
knob, you can set the focus toward
The wanted object.
(4) Re-assemble the camera.
SCREW Tp14x25 3EA
MOUNT HO LEP LATE(STICKER)
SCREW Tp14x25 3EA
MOUNTH OLE PLATE(STICKER)
Put asticker on theceiling andmake holes
accordingto the spots markedon a st icker.
Put asticker on the walland makeholes
accordingto the spots markedon a st icker.
Ø3.5 Ø30
Ø3.5
Ø30
2. Pipe application
. Camera angle adjustment
(1)Remove thescrew for fixing a cable onthe bottom of the base.
(2) Open the DOME COVER.
(3) Remove the TAP COVER and place the cables there.
(4) After distributing cables, use the TEPLON tapeto wipe the pipe.
(5) Combine the pipe to the base.
: Grasp the disk of camera and then adjust
direction to the right or left(-160 ~ 190 )
: Grasp the camera holder and then adjust
direction to the up or down(6 ~ 90 )
: Grasp the camera holder and then rotate
(-178 ~ 178 )
<Caution> If you don't wipe TEFLON tape on pipe, itmight cause troubles on
water-resistant.
3 :
(1) Pan adjustment
(2) Tilt adjustment
(3) Roll adjustment
˚ ˚
˚ ˚
˚ ˚
◐ DIMENSION
<Caution> If you try to adjust the camera out of limited angle, it mig ht cause
troubles and damage to camera.
CABLE
PIPE
TEFLONTAPE
TAP COVER
CABLEFIXING SCRE W
DOMECOVER
Ø100
Ø150.5 Ø129
ROTATION
U
D
R
L
DISK
CAMERA HOLDER
CAMERA
MODULE ASS'Y
◐PRECAUTION
◐FEATURES
1. You can install the camera indoors or outdoors.
2. Choose an ideal location for the camera, since a camera unit must
be protected against vibration.
3. Be careful not to scratch the camera unit, especially lens or dome
cover.
4. Use the camera withi n the tempe rature(-10℃ ~ +50℃).
5. Avoid any direct sun light toward the lens.
6. Use the AC adaptor 12V DC, 300mA regulated.
1. This camera is incredibly flexible to install with its 3-axis camera construction, which makes the cameraceiling,wall or slope m ountable.
2. IP67(Waterproof)
3. Durable material : Body - Aluminum, Dome - Polycarbonate
4. Supreme Resolution(600 T V-Line)
5. Electronic Day & Night function
6. Support 4 different privacy zone
7. DWDR(Digital Wide Dynamic Range)
8. Multifunction: High Light Mask, LensShading Compensation, Motion
Detection
9. Multi-language full O SD support.
If the product is to be put out of op eration definitively,
take it to a local recycling plant for a disposal which
is not harm ful to theenvironment.
Page 2
GST-410
1/3" SONY SUP ER HAD CCD
752(H)x 582(V) Pixel
6.5㎛(H) x6.25㎛(V)
600 TV-Line
PAL
Internal
2:1 Interlace
1.0 Vp-p(Sync.Negative) Termination75Ω±10%
γ
= 0.45(Adjustable)
0.1Lux(F/1.2)
Full OSD
ON /OFF Selectable(64Zone)
ATW/ AWC / MANUAL
ON /OFF Selectable(4 Zone)
Electronic D&N(AUTO, COLOR, B/W)
48dB over(AGC OFF)
ON / OFF
DWDR / BLC/ HLC / OFF
YES
ExtraVideo connectorfor easy installation
Automatic(Adjustable)
1/50~1/100,000sec
Average testilluminance byfront vi ew
Regulated 12V DC ±10%
Max. 130mA(at 12VDC)
Vari-focal auto iris lens
-10 ∼ 50℃
-20 ∼ 60℃
Ø150.5 x95.6(H)mm
Approx. 750g
Ⅱ
Model No.
Image Sensor
Effective Pixel
Cell Size
TV Type
Sync. Type
ScanningSystem
Video Output
Gamma Characteristic
Min. Illumination
OSD
Motion Detectio n
White Balace
PrivacyZone
Day & Night
S/N Ratio
Mirror
Backlight
ControlInterface
Gain Control
Shutter
Test Illuminance Area
CurrentConsumption
Operation Temp.
Preservation Temp.
Dimension
Weight
Resolution
Reverse PolarityProtection
PowerSupply
Lens
◐SPECIFICATION
4. IMAGE
ADJUST
3. DAY&NIGHT
2. WHITE
BALANCE
PATTERN
GENERATOR
3B15939A
www.orion-technology.eu
◐ FUNCTION SETTING
1. How to use the jog lever
①ENTER :
② ③
④ ⑤
⑥EXT-VIDEO:
ㆍPush the lever : Used to access the menu and confirm selection.
ㆍPush the lever fo r one second : Used to return to previous menu
from the motion detection setting section or privacy mask
setting section.
It is used for upgrading the product funct ion
and after-sales services.
⑦DEBUG PORT :
UP, DOWN :
LEFT, R IGHT :
Used to move the cursor to up or down.
Used to move the cursorto left orright and change
the value.
Extra video output terminal for installation.
Plug your test monitor in hear. Thecable is op tion.
7
6
2. OSD menu structure
Fixed focallens or Vari-focalauto iris lens
In case of manual lens selection, adjust the
brightness
Shutterspeed autoadjustable
Select shutterspeed manually
Determines that use the AGC function or not
and AGC levelselectable(You can not use th e
Auto D&N changemode when AGCis off)
DigitalWide DynamicRange
BLC function
High Light Mask function
In case of AUTO mode, the function will off in
daytimeand on atnight
According to the threshold value, the camera
will recogni zeas High lightor not
Colortemperature 2500~ 9500°K
Adjustthe Redor Blue valuesto shift the color
of the object
Move the camera lens toward to white paper
then press the set button to find the optimal
white balancefor current environment
Auto day&night switching mode
Fixed at color
Fixed at B/W
Determines whether totransmitthe burst signal
or not inB/W mode
You can select brightness of illumination about
changing the day ↔ night mode
You canselect thedurationtime aboutchaining
theday ↔ night mode
N/A for W/O LED version
N/A for W/O LED version
Set ahorizontal image inversion
Sharpness adjustable
Gamma adjustable
Determines whether to use the brightness
compensation offour lens'corners(LSC)or not
The LSC levelselectable
AdjustRed tone of the image
AdjustBlue tone of the image
LENS
E.SHUTTER
AGC
DWDR
BLC
HLC
AWB MODE
D&N MODE
LED LEVEL
DYNAMIC IR
MIRROR
SHARPNESS
GAMMA
LSC
R-Y GAIN
B-Y GAIN
BRIGHT
HLC THR
BURST
DELAY TIME
LSC LEVEL
MANUAL, DC
0 ~ 100
AUTO
1/50 ~
1/100,000
OFF, LOW,
MIDDLE, HIGH
OFF, LOW,
MIDDLE, HIGH
OFF, ON
OFF, ON,
AUTO
0 ~ 100
ATW
MANUAL
AWC
AUTO
COLOR
B&W
OFF, ON
117 ~200
82 ~ 165
3 ~ 15
OFF, LOW,
MIDDLE, HIGH
OFF, ON
OFF, ON
0 ~ 50
OFF, ON
0 ~ 50
0 ~ 200
0 ~ 200
0.45,0.6, 1,
USER
1. EXPOSURE
Function
setting menu
Select menu
Contents
Sub menu
Test signal. Press the setbutton,color bar appeared onthe screen
andpress anykey to return to menu
COLOR B&W
B&W COLOR→→
※All specification is subject to ch ange withoutnotice toimprove the quality.
Determines whether touse the motion detection
function ornot
No display on the screen though movement
is detected
The words 'MOTION' appear on the screen
when movemen t is detected
Motion detection area appear on the screen
when movemen t is detected
Motiondetection sensitivity
Set the duration of outside alarm. If the way of
display is message, it means display time of
message
Display each privacy mask or not. Press the
set button to move into the privacy mask
setting section, whenever you press the set
button, the maskcolor is changed. When the
mask color is red you can adjust the size by
up, down, left and right button. When the
mask color is blueyou can set the position of
mask by up, down, leftand right button.Press
the set buttonfor afew second to escape
Select mask color
Select thecamera IDfor RS-485 communication
Select baud rate
Select protocol
Select language
Displaythe cameraID on the screen
Not available
Not available
OFF, ON
NONE
MESSAGE
MASK
0 ~ 255
1 ~ 15
OFF, LOW,
MIDDLE, HIGH
1 ~ 15
OFF, ON
1 ~ 255
2400 ~ 9600
ENGLISH, …
OFF, ON
BLACK,
GRAY…
PELCO-D,
PELCO-P
MOTION
IMPACT
MASK
1, 2, 3, 4
CAM ID
BAUDRATE
PROTOCOL
LANGUAGE
DISPLAY
SET
WINDOW
ALL SET↓
SENSITIVITY
HOLD TIME
HOLD TIME
EDIT
POSITION
MASK
COLOR
NAME
DISPLAY
6. PRIVACY
MASK
7. COMMUNICATION
(Not available)
10. EXIT
9. FACTORY
SET
5. MOTION &
IMPACT
8. SPECIAL
ALLCLEAR↓
Press the set button to move into the motion detection area
sectionto setthe 64 areas.Press theset button fora few second
to move out
Press theset button to select all area
Press theset button to remove allarea
※If you change the COMMUNICATION value through RS-485, you might not
control the camera due to unmatched value(If your camerais out of working
due to above reason, change your controller's value or wait a few minute till
closethe menu, it will be backto previous setting value)
Press the set button to movei nto the name setting section. You
can choose the letter by using up and down button and move
next letter by using left and right button. Press the set buttonfor
a fe w second to move out
Press the set button to move into the position setting section.
You can move the camera ID to your wanted position by using
up, down, left and right button
To reset your camerato factory defaultcondition
Notice : Le ns, communication and language is notchanged
Save the value and then restart
Loading...