Page 1
3-AXIS DAY & NIGHT IR DOME CAMERA
MANUAL
4. Camera angle adjustment :
(1) Pan adjustment
(2)Tilt adjustment
(3) Roll adjustment
: Grasp the disk of camera and then adjust
direction to the right or left(-180 ~ 180 )
: Grasp the LED cover of camera and then adjust
direction to the up ordown(6 ~ 90 )
: Grasp the camera holder and then rotate
(-178 ~ 178 )
˚ ˚
˚ ˚
˚ ˚
◐ DIMENSION
◐ ASSEMBLY
<Cautio n> If you t ry toadjust the camera out of limited an gle, it might cause
troubles and damage to camera.
◐PRECAUTION
◐FEATURES
1. Do not install the cam era outdoors.
2. Choose an ideal location for the camera, since a camera unit must
be protected against moisture and vibration.
3.Be careful notto scratch the camera unit, especially lens or dome cover.
4. Use the camera within the temperature(-10℃ ~ +50℃).
5.Handle with care.Dropping it cancauseserious damage to the camera.
6. Avoid any direct sun light toward the lens.
7. Use theAC adaptor 1 2V DC, 1A regulated.
Dual voltage product can use 24V AC adaptor.(op tion)
1. This camera is incredibly flexible to install with its 3-axis camera
construction, which makes the camera ceiling, wall or slope
mountable.
2. 25M range visible in total darkness with 24pcs of IR LEDs.
3. RS-485 interface(Pelco-D, Pelco-P protocol support) - Option
4. Supreme Resolution(600 TV-Line)
5. Day & Night function(ICR) - Option
6. Support 4 different privacy zone
7. IR LED output level controllable via RS-485
8. DWDR(Digital Wide Dynamic Range)
9. Multi funct ion: High Light Mask, Lens Shading Compensation, Impact
Detection, Motion Detection
10. Dynamic IR : When IR LED is turned on in B/W, the objects can be
clearly identified due to the function that decreases screen saturation
of objects within a short distance.
11. Multi-language full OSD support
If th e product is to be put out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.
◐ HOW TO INSTALL
1. Opening the dome
2. Removing the dome
3. Camera installation
:
:
:
Pushing the latchbutton. (Remove the protection
sheet after installing.)
Lift the dome . When you push the latch
button,it is unlocked andyou can lift the dome.
(1) Fix the camera set with the supplied screws on ceiling or wall mount.
If you don't use supplied screws, the came ra may fall off.
(2) Please refer to '4. Camera angle adjustment' regarding adjust
camera angle.
(3) Lens adjustment(Vari-focal L ens only)
After opening the LEDcover,
① By turning the "Tele-Wide" knob ,
you can access a range of focal
lengths within specified limits.
② Since then, by turning the "Near-Far"
knob, you can set the focus toward
the wanted object.
(4) Re-assemb le the came ra.
<Ceiling mount>
ROTATION
U
D
R
L
LED COVER
DISK
CAMERAHOLDER
Ø100
Ø130.8 Ø109
SCREW TP1
3.5x202EA
SCREW TP1
3.5x202EA
<Wall mount>
DOME COVER
LED COVER
SCREW
CAMERAMODULE
SCREW
CABLE
DISK
BASE
CONTROLPCB
PUSH BUTTON
HARNESS
SCREW
PROTECTION SHEET
LATCH BUTTON
Page 2
2. How to use the jog lever
3. How to control through RS-485 communication
4. Cable array o
①ENTER :
②UP, ③DOWN
④LE FT, ⑤RIGHT
⑥EXT-VIDEO
⑦DEBUG PORT :
1) No impact & motion alarm type
2) Built-in impact & m otion alarm type
ㆍPush the lever : Used to access the menu andconfirm selection.
ㆍPush the lever for one second : Used to re turn to previous menu
from the motion detection setting section or privacy ma sk setting
section.
: Used to move the cursor to up or down.
: Usedto move thecursor to left or right andchange
the value.
: Extra video output terminal for installation .
Plug your test monitor in hear. The cableis option.
It is used for upgrading the product function and
after-sa les services.
ch the camera with controller's ID, baudrate and protocol
2) Up, Down, Left and right of Jog lever is same as Up, Down, Left
and right of RS-485 cont roller
3) Enter of Jog lever i s the same as menu key or I RIS op en key of
RS-485 controller
4) Return to previous menu from motion detection setting section and
privacy mask setting section : Iris close or Iris open for a few second.
Or press the button as Up
(option)
( ption)
1) Mat
→ Right→ Down → Left successively
※All specification is subject to change withoutnotice to improvethe quality.
◐FUNCTION SETTING
1. OSD menu structure
Fixed focal lens or Vari-focal auto iris lens
Adjust the brightness
Shutterspeed autoadjustable
Select shutter speedmanually
Determines that use the AGC function or not
and AGC levelselectable(You can not use the
Auto D&N change mode whe n AGC is off)
DigitalWide DynamicRange
BLC function
High Light Mask function
In case of AUTO mode, the function will off in
daytimeand on atnight
According to the thresholdvalue, the camera
will recognize as High light or not.
LENS
E.SHUTTER
AGC
DWDR
BLC
HLC
BRIGHT
HLC THR
MANUAL, DC
0 ~ 100
AUTO
OFF, LOW,
MIDDLE, HIGH
OFF, ON
OFF, ON,
AUTO
0 ~ 100
1. EXPOSURE
1/60(1/50) ~ 1/100,000
Function
setting menu
Select menu ContentsSub menu
OFF, LOW,MIDDLE, HIGH
Color temperature 2500 ~ 9500°K
Adjustthe Redor Blue values to shift the color
of the object
Move the camera lens toward to white paper
then press the Enter button to findthe optimal
white balance for currentenvironment
Auto day&nightswitching mode
Fixed at color(LED OFF)
Fixed at B/W(LED ON)
Determines whether totransmitthe burst signal
or not in B/W mode
You can select brightness of il lumination about
changing the day ↔ night mode
You canselect the duration timeabout chaining
theday ↔ nightmode
IR LED OFF/ON and output level adjustable
When IR LEDis turned on in B/W, the objects
can be clearly identified due to the function
that decreases screen saturation of objects
within a short distance.
Set ahorizontal image inversion
Sharpness adjustable
Gamma adjustable
Determines whether to use the brightness
compensation offour lens' corners(LSC) or not
The LSC levelselectable
AdjustRed tone of the image
AdjustBlue tone of theimage
Determines whether touse the motion detection
function ornot
No display on the screen though movement
is detected
The words 'MOTION' appear on the screen
when movementis detected
Motion detection area appear on the screen
when movementis detected
Motiondetection sensitivity
Set the duration of outside alarm. If the way of
display is message, it means display time of
message
Determines whether to use impact detection
functionor not and sensitivitysetting
Set the duration of outside alarm and display
time of "IMPACT"message
Display each privacy mask or not. Press the
Enter button to move into the privacy mask
settingsection, whenever youpress the Enter
button, the maskcolor is changed. When the
mask color is red yo u can adjust the size by
up, down, left and right button. When the
mask color is blueyou can setthe position of
mask by up, down, left and right button.Press
the Enter buttonfor afew secon d to escape
Select mask color
Select thecamera IDfor RS-485 communication
Select baud rate
Select protocol
Select language
Displaythe cameraID on the screen
ATW
MANUAL
AWC↓
AUTO
COLOR
B&W
OFF, ON
85 ~ 170
50 ~ 135
3 ~ 15
OFF, ON
OFF, ON
0 ~ 50
OFF, ON
0 ~ 50
0 ~ 200
0 ~ 200
OFF, ON
NONE
MESSAGE
MASK
0 ~ 255
1 ~ 15
OFF, LOW,
MIDDLE, HIGH
1 ~ 15
OFF, ON
1 ~ 255
2400 ~ 9600
ENGLISH, …
OFF, ON
Press the Enter button to move into the motion detection area
section to set the 64 areas. Press the Enter button for a few
second to move out
Press the Enter button to select all area
Press the Enter button to remove allarea
AWB MODE
D&N MODE
LED LEVEL
DYNAMIC IR
MIRROR
SHARPNESS
GAMMA
LSC
R-Y GAIN
B-Y GAIN
MOTION
IMPACT
MASK
1, 2, 3, 4
CAM ID
BAUDRATE
PROTOCOL
LANGUAGE
BURST
DELAY TIME
LSC LEVEL
DISPLAY
SET
WINDOW
ALL SET↓
SENSITIVITY
HOLD TIME
HOLD TIME
EDIT
POSITION
6. PRIVACY
MASK
7. COMMUNICATION
(option)
10. EXIT
9. FACTORY
SET
5. MOTION &
IMPACT
4. IMAGE
ADJUST
3. DAY&NIGHT
0.45, 0.6, 1, USER
PELCO-D, PELCO-P
MASKCOLOR
NAME DISPLAY
BLACK, GRAY…
8. SPECIAL
2. WHITE
BALANCE
ALLCLEAR↓
COLOR B&W
B&W COLOR→→
OFF, LOW , MIDDLE, HIGH
PATTERN
GENERATOR
Press the Enter button to move into the name setting section.
You can choose the letter by using up and down button and
move next letter by using left and right button. Press the Enter
buttonfor a few second to move out
Press the Enter button to move into the position setting section.
You can move the camera ID to your wanted position by using
up, down, left and right button
※If you change the COMMUNICATION val ue through RS-485, you might not
control the camera due to unmatchedvalue(If your camera is out of working
due to above reason, change you r controller's value or wait a few minute till
closethe menu, it willbe back to previous setting value)
To reset your camera to factory defaultcondition
Notice : Lens, communicati on and languagei s not changed
Save the val ue and then restart
Test signal.PresstheEnterbutton,color barappeared on the screen
andpressanykey to return to menu(600TV-Lineversion only)
3B05874E
E : ORANGE(RX+)
F :WHITE(RX -)
A :BLUE(MOTION)
B :BLACK(GND)
C : GREEN(IMPACT)
D :BLACK(GND)
E : ORANGE(RX+)
F :WHITE(RX -)
MOTIONALARM
GND
IMPACT ALARM
GND
RX +
RX -
A
B
C
D
E
F
FUNCTION REMARK
No.
◐SPECIFICATION
9.6㎛(H) X 7.5
㎛(V)(NTSC)
9.8㎛(H)X 6
.3㎛(V)(PAL)
510(H) X 492(V) PIXEL(NTSC)
500(H) X 582(V) PIXEL(PAL)
Image Sensor
Impact Detection
TV Type
Sync. Type
ScanningSystem
Video Output
Gamma Characteristic
OSD
Motion Detection
White Balace
PrivacyZone
Day & Night
S/N Ratio
Mirror
Backlight
ControlInterface
AGC
Shutter
Test Illuminance Area
CurrentConsumption
Operation Temp.
Preservation Temp.
Dimension
Weight
Type 1 Type 3
380 TV-Line
Max. 450mA(at 12V DC)
Vari-focal autoiris
Day &Night lens
Vari-focal autoiris lens
or Fixed focal lens
ICR(AUTO, COLO R,B/W)
Electronic D&N(AUTO, COLOR, B/W)
Max. 600mA
Reve rse PolarityProtection
1/3" SONY SUPER HAD CCDⅡ
Effective Pixel
Cell Size
Resolution
Min. Illumination
PowerSupply
Lens
6.35㎛(H)X 7.
4㎛(V)(NTSC)
6.5㎛(H)X 6.
25㎛(V)(PAL)
768(H) X 494(V) PIXEL(NTSC)
752(H) X 582(V) PIXEL(PAL)
600 TV-Line
COLOR : 600 TV-Line
B/W :680 TV-Line
0.05 Lux(F/1.2) : LEDOFF
0.01 Lux(F/1.2) :LED OFF
0.1 Lux(F/1.2) : LEDOFF
Commun ication(opt ion)
Type 2
NTSC/ PAL
Internal
2:1 Interlace
1.0 Vp-p(Sync . Negative) Termination 75Ω±10%
γ
= 0.45(Adjustable)
0 Lux(20M Range) : LED ON
Yes(Multi-language)
ON / OFF Selectable(64 Zone)
ON /OFF Selectable(3 Step : LOW /M IDDLE / HIGH)
ATW/ AWC (2,500 ~ 9,500°K) /MANUAL
ON / OFF Selectable(4 Zone)
RS-485(PELCO-D&P)
48dB over(AGC OFF)
ON /OFF
DWDR /BLC / HLC / OFF
YES
Sub control board with extra videoc onnector
LOW / MIDDLE / HIGH/ OFF
1/60~1/100,000sec(NTSC), 1/50~1/100 ,000sec(PAL)
Average test illuminance by front view
-10 ∼50℃
-20 ∼60℃
Ø130.8X 96(H)mm
Approx.500g
Regulated 12V DC±10%
12V DC, 24V AC
Dual Voltage (option)
6
7
1
2
4
3
5
ㆍ If the camera detected motion when using Motion & Impact
function,outside line ofmotion alarmconnect with GND(B).
ㆍIf the cameradetect impact, outsideline ofimpact alarm connect
with GND(D).Outputs ofMotion & Impact are'open collector'.
ㆍMax current & voltageare 200mAand 30V DC.
RS-485A
RS-485B
Loading...