Orion Cobalt CO104S, Cobalt CO124S, Cobalt CO154S, CO104D, CO154D Owner's Manual

Subwoofer MODEL

CO104S
CO124S
CO154S

OWNER'S MANUAL

© 2012 MD Audio Engineering—all rights reserved

1

TABLE OF CONTENTS

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Español. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Italiano. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Português . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Practice Safe Sound™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

What's in the box . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Tools of

the Trade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Finding Speaker Mounting Locations . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . 2

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Wiring Configurations

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Enclosure Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover

INTRODUCTION

Thank you for your purchase of the Orion Cobalt Subwoofers. These woofers
represent a combination of incredible performance and value. We at Orion strive to
give you the latest up to date information about this product. What we can’t give you
with the manual is personal installation or technical experience. If you have questions
concerning the use or application of this product please refer to the nearest ORION
dealer for assistance, visit www.orioncaraudio.com, or call the technical support hot­line at 1-800-876-0800. As we are always finding new ways to improve our product,
the features and specifications are subject to change without notice.

PRACTICE SAFE SOUND™

Continuous exposure to sound pressure levels over 100dB may cause permanent
hearing loss. High powered automotive sound systems can generate sound pressure
levels in excess of 130dB. When playing your system at high levels, please use hearing
protection and prevent long term exposure.

Model Number:

Serial Number:

Date of Purchase:

2

© 2012 MD Audio Engineering—all rights reserved

WHAT’S IN THE BOX

Included in this box are all the necessary mounting hardware and cables for your basic
installation. Listed below is a detailed list of the components included in this system
package.

Quantity Description

1 Installation and Operation Manual
1 Orion™ Cobalt woofer
1 Mounting template

Mounting screws

INSTALLATION

The performance of these Cobalt subwoofers is directly proportional to the quality
of the installation. Care taken with the installation process will be rewarded by years
of satisfying performance. If you are unsure of your installation abilities, please
refer to your local authorized Orion dealer for assistance. Orion dealers are trained
professionals dedicated to extracting the maximum performance out of your Orion
system. If you decide to install this speaker system yourself, please read the entire
section on sealed and vented enclosures before starting the installation. .

TOOLS OF THE TRADE

Listed are the majority of the tools required to perform the installation. Having the
proper tools will make the installation much easier. It is very difficult when you get
half way through the installation and discover that you require a specific tool to
get yourself through a particular part of the installation. Some of these tools are
necessities. Some make the job much easier.

• Marking Pen • Electric Drill and assorted Bits

• Phillips Screwdriver • Wire Strippers

• Allen Wrenches • Volt/Ohm Meter (Optional)

• Table Saw • Jig Saw

• Wire Cutters • Wire Crimpers

FINDING SPEAKER MOUNTING LOCATIONS

Choosing the correct speaker locations will have the greatest effect on the
sound quality of the system. Different considerations are needed when choosing
the locations that best suit your needs. The locations must be large enough for
the speakers to fit. Care is needed to ensure that the location you have chosen
will not affect any of the mechanical or electrical operations of the vehicle.

Determining the best location for the speakers will depend on your cosmetic needs
and your vehicle's interior. If minimal intrusion in your vehicle is desired, factory
speaker locations may be the ticket for you. These woofers are too large to fit most
factory locations and typically need enclosures to perform correctly.

© 2012 MD Audio Engineering—all rights reserved

3

FEATURES

15

1

2

13

3

14

4

5

12

6
7

11

10

9

8

1

Polypropylene dust cap - moisture and UV resistant.

2

Oversized NBR (Nitrile-butadiene Rubber) surround for linear

controlled long excursion.

3

Vented paper cone - moisture and UV resistant.

4

Custom stamped steel frame.

5

Vented Kapton voice coil former (10” & 12" uses 1.5" voice coil
former, 15” use a 2" voice coil former).

6

8mm steel front plate.

7

Large 2 stack ceramic magnets.

8

8mm steel back plate/pole piece T yoke assembly.

9

.75" vent. Part of the enhanced voice coil cooling system (forced
convection).

10

PVC magnet protector.

11

High temperature Copper 4 ohm voice coil.

12

Venting in voice coil former. Part of the enhanced voice coil cooling
system (forced convection).

13

Interlaced Conex spider with stitched and looped tinsel leads
attached.

14

Push Terminals.

15

Reversible PVC mounting gasket.

4

© 2012 MD Audio Engineering—all rights reserved

WIRING CONFIGURATIONS

The following illustrations provide guidelines on properly connecting your
Orion Cobalt woofer to an Orion Cobalt amplifier for maximum performance.

Recommended Amplifier Power

Continuous Power (RMS)

Peak Power (Watts)

1 woofer

100 to 300

200 to 600

2 woofers

200 to 600

400 to 1200

3 woofers

300 to 900

600 to 1800

4 woofers

400 to 1200

800 to 2400

Parallel—Two Speakers ( 4 ohm voice coils)

Two 4 ohm voice coil woofers with the two woofers in parallel results in a 2 ohm load
to the amplifier..

_

_

4 ohm

4 ohm

+

+

Figure 2
Figura 2
Abbildung 2

+

_

1. Connect the speaker in parallel by connecting the two positive (+) terminals
together and the two negative (-) terminals together.

2. Wire the positive (+) terminals of the woofers to the positive (+) terminal on
the amplifier. Wire the negative (-) terminals of the woofers to the negative (-)
terminal on the amplifier.

© 2012 MD Audio Engineering—all rights reserved

5

One Speaker (4 ohm voice coil)

One 4 ohm voice coil woofer results in a 4 ohm load to the amplifier.

_

4 ohm

+

Figure 3
Figura 3
Abbildung 3

+

_

1. Connect the speaker by connecting the positive (+) terminal of the woofer to
the positive (+) terminal on the amplifier. Wire the negative (-) terminal of the
woofer to the negative (-) terminal on the amplifier.

6

© 2012 MD Audio Engineering—all rights reserved

Series—Two Speakers (Single 4 ohm voice coils)

Two single 4 ohm voice coil subwoofers with the voice coils connected in series to
result in an 8 ohm load to the amplifier.

_

_

4 ohm

4 ohm

+

+

Figure 4
Figura 4
Abbildung 4

+

_

1. Connect the woofers in series by connecting the negative (-) terminal of the first
woofer voice coil to the positive (+) terminal of the second woofer voice coil.

2. Wire the positive (+) terminal of the first woofer voice coil to the positive (+)
terminal on the amplifier. Wire the negative (-) terminal of the second woofer
voice coil to the negative (-) terminal on the amplifier.

© 2012 MD Audio Engineering—all rights reserved

7

Series/Parallel - 4 Speakers (Single 4 Ohm Coils)

4 single 4 ohm voice coil subwoofers with the voice coils of each pair of speaker wired
in series and then all 4 speakers wired in parallel to result in a 4 ohm load on the
amplifier.

_

4

ohm

_

4

ohm

_

4

ohm

_

4

ohm

1 2 3 4

+

+

+

+

Figure 5
Figura 5
Abbildung 5

+

_

1. Connect the negative (-) terminal from speaker 1 to the negative terminal on
speaker 3 and then hook that wire to the negative (-) terminal on the amplifier.

2. Connect the positive (+) terminal from speaker 1 to the negative (-) terminal on
speaker 2.

3. Connect the positive (+) terminal from speaker 3 to the negative (-) terminal on
speaker 4.

4. Connect the positive (+) terminal from speaker 2 to the positive (+) terminal on
speaker 4 and then hook that wire to the positive (+) terminal on the amplifer.

8

© 2012 MD Audio Engineering—all rights reserved

ENCLOSURE RECOMMENDATIONS

Enclosure Details

1. External dimensions calculated for 3/4” building material

2. Includes speaker displacement

3. Volumes given are net tuning volume

4. Enclosures include a minimal amount of damping material. Just enough material
to line the inside of the enclosure is required.

Cobalt CO104S Sealed Enclosure Recommendations

External Dimensions

A = 14 in
B = 12.5 in
C = 11.5 in

Internal Dimensions

A

B = 11 in
C = 10 in

C

Wall Thickness

Front = 0. 75 in

B

Side = 0.75 in

c

Top &

Bottom

b

d

a

Back

c

Sides

—Box Parts—
Box Shape: Square Prism
1 Top, 1 Bottom:

depth (c) = 11.5 in
width (b) = 12.5,
thickness = 0.75 in

1 Front, 1 Back:

height (a) = 12.5 in
width (d) = 11,
thickness = 0.75 in

2 Sides: height (a) = 12.5 in

thickness = 0.75 in

Figure 6
Figura 6
Abbildung 6

—Driver Mounting—

Front

© 2012 MD Audio Engineering—all rights reserved

9

Cobalt CO104S Vented Enclosure Recommendations

Figure 7
Figura 7
Abbildung 7

A

B

External

Dimensions

A = 15.75

in

B = 14.25

in

C = 12 in

Internal

Dimensions

B = 12.75 in
C = 10.5

in

C

Wall

Thickness

Front = 0.75

in

Side = 0.75

in

c

Bottom

b

d

Front

&

a

Back

c

Sides

—Box

Parts—

Box Shape: Square

Prism

depth (c) = 12

in

width (b) =

14.25,

thickness = 0.75 in

1 Front, 1

Back:

height (a) = 14.25

in

width (d) =

12.75,

thickness = 0.75 in

height (a) = 14.25

in

depth (c) =

12,

thickness = 0.75 in

VENT

Round

h

e

g

- OR -

VENT

Square

e

h

h

g

—Driver

Mounting—

Front

Vent Parts ---

Round

1 Duct: outside diameter (e) =

3.2

inside diameter (g) = 3

in

length (h) = 9.5 in

Vent Parts ---

Square

1 Top, 1

Bottom:

width (e) =

3,
length (h) = 10 in
thickness = 0.125

in

2

Sides:

height (g) =

2.75,

length (h) = 10

in

thickness = 0.125 in

10

© 2012 MD Audio Engineering—all rights reserved

Cobalt CO124S Sealed Enclosure Recommendations

External Dimensions

A = 15.5 in
B = 14.75 in
C = 12 in

Internal Dimensions

A

B = 13.25 in

C = 10.5 in

C

Wall Thickness

Front = 0. 75 in

B

Side = 0.75 in

c

Top &

Bottom

b d

a

Back

c

Sides

—Box Parts—
Box Shape: Square Prism
1 Top, 1 Bottom:

depth (c) = 12 in
width (b) = 14.75,
thickness = 0.75 in

1 Front, 1 Back:

height (a) = 14 in
width (d) = 13.25,
thickness = 0.75 in

2 Sides:

depth (c) = 12,
thickness = 0.75 in

Figure 8
Figura 8
Abbildung 8

Driver Mounting
Mounting: Front

© 2012 MD Audio Engineering—all rights reserved

11

Cobalt CO124S Vented Enclosure Recommendations

Figure 9
Figura 9
Abbildung 9

A

B

External Dimensions

A = 18 in
B = 16.75 in
C = 13 in

Internal Dimensions

B = 15.25 in
C = 11.5 in

C

Wall Thickness

Front = 0. 75 in
Side = 0.75 in

c

Bottom

b d

Front &

a

Back

c

Sides

—Box Parts—
Box Shape: Square Prism

depth (c) = 13 in
width (b) = 16.75,
thickness = 0.75 in

1 Front, 1 Back:

height (a) = 16.5 in
width (d) = 15.25,
thickness = 0.75 in

height (a) = 16.5 in
depth (c) = 13,
thickness = 0.75 in

VENT Round

h

e

g

- OR - VENT
Square

e

h

h

g

Driver Mounting
Mounting: Front

Vent Parts --- Round
1 Duct:

outside diameter (e) = 4.25
inside diameter (g) = 4 in
length (h) = 10 in

Vent Parts --- Square

width (e) = 3.75,
length (h) = 10 in
thickness = 0.125 in

2 Sides:

height (g) = 3.5,
length (h) = 10 in
thickness = 0.125 in

12

© 2012 MD Audio Engineering—all rights reserved

Cobalt CO154S Sealed Enclosure Recommendations

External Dimensions

A = 25 in
B = 17.5 in
C = 11.5 in

Internal Dimensions

A

B = 16 in

C = 10 in

C

Wall Thickness

Front = 0. 75 in

B

Side = 0.75 in

c

Top &

Bottom

b d

a

Back

c

Sides

—Box Parts—
Box Shape: Square Prism
1 Top, 1 Bottom:

depth (c) = 11.5 in
width (b) = 17.5,
thickness = 0.75 in

1 Front, 1 Back:

height (a) = 23.5 in
width (d) = 16,
thickness = 0.75 in

2 Sides:

depth (c) = 11.5,
thickness = 0.75 in

Figure 10
Figura 10
Abbildung 10

Driver Mounting
Mounting: Front

© 2012 MD Audio Engineering—all rights reserved

13

Cobalt CO154S Vented Enclosure Recommendations

Figure 11
Figura 11
Abbildung 11

A

B

External Dimensions

A = 25 in
B = 17.5 in
C = 13 in

Internal Dimensions

B = 16 in
C = 11.5 in

C

Wall Thickness

Front = 0. 75 in
Side = 0.75 in

c

Bottom

b d

Front &

a

Back

c

Sides

—Box Parts—
Box Shape: Square Prism

depth (c) = 13 in
width (b) = 17.5,
thickness = 0.75 in

1 Front, 1 Back:

height (a) = 23.5 in
width (d) = 16,
thickness = 0.75 in

height (a) = 23.5 in
depth (c) = 13,
thickness = 0.75 in

VENT Round

h

e

g

- OR - VENT
Square

e

h

h

g

Driver Mounting
Mounting: Front

Vent Parts --- Round
1 Duct: outside diameter (e )

inside diameter (g) = 4 in
length (h) = 7 in

Vent Parts --- Square
1 Top, 1 Bottom:

length (h) = 7 in
thickness = 0.125 in

2 Sides:

height (g) = 4,
length (h) = 7 in
thickness = 0.125 in

14

© 2012 MD Audio Engineering—all rights reserved

SPECIFICATIONS

Model/Part Number

CO104S

CO124S

CO154S
Thiele/Small Parameters
Fs (free-air resonance, Hz)

39.2

25.6

25.2

Vas (equivalent compliance, cu. ft.)

1.080

4.017

7.098

Vas (equivalent compliance, liters)

30.600

113.790

201.070

Qms (Q, mechanical)

3.53

4.72

6.08

Qes (Q, electrical)

0.68

0.55

0.51

Qts (total driver Q)

0.57

0.49

0.47

Re (DC resistance, ohms)

3.6

3.55

3.77

Z (nominal impedance, ohms)

4

4 4

Le (inductance, mh)

1.38

1.37

1.61

Efficiency (1W @ 1M, dB)

86.1

87.2

89.9

Xmax (one way linear excursion, in.) 0.406

0.410

0.453

Xmax (one way linear excursion, mm) 10.2925

10.4075

11.5

Pe (continuous power handling,
watts)

200

200

250

Peak power handling (music, watts)

400

500

600
Mms (total moving mass, grams)

101.00

127

195
Cms (mechanical compliance, mm/N) 0.180564

0.294721

0.211994

Bl (motor strength, Tesla-M)

10.88

11.61

14.82

Sd (effective radiating area, sq. cm.)

346.361

522.792

819.398

Sd (effective radiating area, sq. in.)

53.706

81.064

127.055

Frequency range (Hz)

39 - 250Hz 25 - 250Hz 25 - 250Hz

Energy Bandwidth Product (EBP)

58

47 49

Driver Physical Dimension
Speaker Displacement (cu ft)

0.048

0.061

0.116
Speaker Outer Diameter (inches/mm) 10.31/ 262 12.40/ 315 15.40/ 391
Mounting hole diameter (inches/mm) 9.23/ 232

10.91/ 277 13.82/ 351

Mounting depth (inches/mm)

5.12/ 130

5.51/ 140

6.46/ 164
Magnet Weight (Oz)

38.60

41

70

Basket diameter (inches/mm)

10.16/258 12.21/310 15.16/385
Recommended Enclosures
Typical sealed enclosure (cu. ft.)

0.75

1

2

Specifications subject to change wit hout notice

© 2012 MD Audio Engineering—all rights reserved

15

A

B

C

D

E

Figure 12
Figura 12
Abbildung 12

CO104S

CO124S

CO154S

Dimensions inches/mm, Dimensions po/mm, Dimensiones
plg./mm, Abmessungen Zoll/mm, Dimensioni
pollici/millimetri, Dimensões polegadas/mm

A

5.12/130

5.51/140

6.46/164

B

1.97/50

1.97/50

2.01/51

C

4.96/126

5.00/127

5.71/145

D

9.13/232

10.91/277

13.82/351

E

10.16/258

12.20/310

15.16/385

© 2012 MD Audio Engineering—all rights

17

FRANÇAIS
CARACTÉRISTIQUES

15

1

2

13

3

14

4

5

12

6
7

11

10

9

8

1

Cache-poussière en polypropylène — résiste à l'humidité et aux

ultraviolets

2

Panneau surdimensionné en nitrile pour un mouvement long à contrôle

linéaire

3

Membrane de papier ventilée — résiste à l'humidité et aux ultra-violets

4

Cadre sur mesure en acier matricé

5

Gabarit ventilé Kapton de bobine acoustique (les modèles 10” et 12"

utilisent le gabarit 1,5", le modèle 15” utilisent le gabarit 2")

6

Platine avant en acier de 8 mm

7

2 grands aimants en céramique

8

Platine arrière/collier T polaire en acier 8 mm

9

Évent de 0,75". Élément du système amélioré de refroidissement de la

bobine acoustique (convection forcée)

10

Protecteur d'aimant en PVC

11 Bobine acoustique 4 ohms en cuivre résistant aux hautes températures
12 Évent du gabarit de bobine acoustique. Élément du système amélioré de

refroidissement de la bobine acoustique (convection forcée)

13 Anneau de centrage Conex entrelacé avec fils rosettes piqués et bouclés

joints

14

Bornes-poussoirs

15 Joint de montage réversible en PVC

18

© 2012 MD Audio Engineering—all rights

CONFIGURATIONS DE CÂBLAGE

Les illustrations suivantes fournissent des indications sur le câblage correct de votre
haut-parleur Orion Cobalt à un amplificateur Orion Cobalt pour un rendement optimal.

Puissance d'amplificateur recommandée

Puissance continue (RMS)

Puissance de crête (watts)

1 haut-parleur 100 à 300

200 à 600

2 haut-parleurs 200 à 600

400 à 1200

3 haut-parleurs 300 à 900

600 à 1800

4 haut-parleurs 400 à 1200

800 à 2400

Parallèle — Deux haut-parleurs (bobines acoustiques 4 ohms)

Deux haut-parleurs à bobine acoustique de 4 ohms en parallèle résultent en une
charge de 2 ohms pour l'amplificateur.

1. Raccordez le haut-parleur en parallèle en raccordant les deux bornes positives (+)
d'une part et les deux bornes négatives (-) d'autre part.

2. Raccordez les bornes positives (+) des haut-parleurs à la borne positive (+) de

l'amplificateur. Raccordez les bornes négatives (-) des haut-parleurs à la borne
négative (-) de l'amplificateur (figure 2).

Un haut-parleur (bobine acoustique 4 ohms)

Un haut-parleur à bobine acoustique de 4 ohms résulte en une charge de 4 ohms pour
l'amplificateur.

1. Raccordez le haut-parleur en raccordant la borne positive (+) du haut-parleur à

la borne positive (+) de l'amplificateur. Raccordez la borne négative (-) du haut­parleur à la borne négative (-) de l'amplificateur (figure 3).

Série — Deux haut-parleurs (bobines acoustiques simples 4 ohms)

Deux haut-parleurs à bobine acoustique simple de 4 ohms en série résultent en une
charge de 8 ohms pour l'amplificateur.

1. Raccordez le haut-parleur en série en raccordant la borne négative (-) d'une

bobine à la borne positive (+) de l'autre bobine.

2. Raccordez la borne positive (+) de la première bobine à la borne positive (+) de

l'amplificateur. Raccordez la borne négative (-) de la seconde bobine à la borne
négative (-) de l'amplificateur (figure 4).

© 2012 MD Audio Engineering—all rights

19

Série/parallèle — 4 haut-parleurs (bobines 4 ohms simples)

Quatre caissons de basses à bobines acoustiques simples de 4 ohms, les bobines
acoustiques de chaque paire de haut-parleurs raccordées en série et les quatre
haut-parleurs raccordés en parallèle, résultent en une charge de 4 ohms pour
l'amplificateur.

1. Raccordez la borne négative (-) du haut-parleur #1 à la borne négative du haut­parleur #3, puis raccordez ce câble à la borne négative (-) de l'amplificateur.

2. Raccordez la borne positive (+) du haut-parleur #1 à la borne négative du haut­parleur #2.

3. Raccordez la borne positive (+) du haut-parleur #3 à la borne négative du haut­parleur #4.

4. Raccordez la borne positive (+) du haut-parleur #2 à la borne positive (+) du
haut-parleur #4, puis raccordez ce câble à la borne positive (+) de l'amplificateur
(figure 5).

NOTE: Diagramme de référence aux pages 4 - 7

RECOMMANDATIONS SUR LES ENCEINTES

Détails des enceintes

1. Dimensions externes calculées pour des matériaux de 3/4”

2. Inclut le volume d'encombrement des haut-parleurs

3. Les volumes indiqués sont le volume d'accord net

4. Les enceintes contiennent une quantité minimale de matériaux d'amortissement. Il
suffit de prévoir assez de tissu pour le revêtement intérieur de l'enceinte.

20

© 2012 MD Audio Engineering—all rights

Recommandations pour l'enceinte
close Cobalt CO104S (Figure 6)

Dimensions externes

A = 14"
B = 12,5"
C = 11,5"

Dimensions internes

A = 12,5"
B = 11"
C = 10"

Épaisseur de la cloison

Avant = 0,75"
Côté = 0,75"

— Parties du boîtier —
Forme: prisme carré
1 haut, 1 bas

Profondeur (c) = 11,5"
Largeur (b) = 12,5"
Épaisseur = 0,75"

1 avant, 1 arrière

Hauteur (a) = 12,5"
Profondeur (d) = 11"
Épaisseur = 0,75"
2 côtés: Hauteur (a) = 12,5"

Profondeur (c) = 11,5"

Épaisseur = 0,75"

— Montage moteur —

Avant

Recommandations pour l'enceinte
ventilée Cobalt CO104S (Figure 7)

Dimensions externes

A = 15,75"
B = 14,25"
C = 12"

Dimensions internes

A = 14,25"
B = 12,75"
C = 10,5"

Épaisseur de la cloison

Avant = 0,75"
Côté = 0,75"

— Parties du boîtier —
Forme: prisme carré
1 haut, 1 bas:

Profondeur (c) = 12"
Largeur (b) = 14,25"
Épaisseur = 0,75"

1 avant, 1 arrière:

Hauteur (a) = 14,25"
Profondeur (d) = 12,75"
Épaisseur = 0,75"
2 côtés:
Hauteur (a) = 14,25"

Profondeur (c) = 12"

Épaisseur = 0,75"

— Montage moteur —

Avant

Pièces d'évent — rond
1 conduit: diamètre extérieur (e) = 3,25"

Diamètre intérieur (g) = 3"

Longueur (h) = 9,5"

Pièces d'évent — carré
1 haut, 1 bas:

Largeur (e) = 3"

Longueur (h) = 10"

Épaisseur = 0,125"

2 côtés:

Hauteur (g) = 2,75"

Longueur (h) = 10"

Épaisseur = 0,125"

NOTE: Diagramme de référence aux pages 8 - 13

© 2012 MD Audio Engineering—all rights

21

Recommandations pour l'enceinte
close Cobalt CO124S (Figure 8)

Dimensions externes

A = 15,5"
B = 14,75"
C = 12"

Dimensions internes

A = 14"
B = 13,25"
C = 10,5"

Épaisseur de la cloison

Avant = 0,75"
Côté = 0,75"

— Parties du boîtier —
Forme: prisme carré
1 haut, 1 bas:

Profondeur (c) = 12"
Largeur (b) = 14,75"
Épaisseur = 0,75"

1 avant, 1 arrière:

Hauteur (a) = 14"
Profondeur (d) = 13,25"
Épaisseur = 0,75"
2 côtés:
Hauteur (a) = 14"

Profondeur (c) = 12"

Épaisseur = 0,75"

— Montage moteur —

Avant

Recommandations pour l'enceinte
ventilée Cobalt CO124S (Figure 9)

Dimensions externes

A = 18"
B = 16,75"
C = 13"

Dimensions internes

A = 16,5"
B = 15,25"

C = 11,5"

Épaisseur de la cloison

Avant = 0,75"
Côté = 0,75"

— Parties du boîtier —
Forme: prisme carré
1 haut, 1 bas:

Profondeur (c) = 13"
Largeur (b) = 16,75"
Épaisseur = 0,75"

1 avant, 1 arrière:

Hauteur (a) = 16,5"

Profondeur (d) = 15,25"
Épaisseur = 0,75"
2 côtés:
Hauteur (a) = 16,5"

Profondeur (c) = 13"

Épaisseur = 0,75"

— Montage moteur —

Avant

Pièces d'évent — rond
1 conduit: Diamètre extérieur (e) = 4,25"

Diamètre intérieur (g) = 4"
Longueur (h) = 10"

Pièces d'évent — carré
1 haut, 1 bas:

Largeur (e) = 3,75"
Longueur (h) = 10"
Épaisseur = 0,125"

2 côtés:

Hauteur (g) = 3,5"
Longueur (h) = 10"

Épaisseur = 0,125"

22

© 2012 MD Audio Engineering—all rights

Recommandations pour l'enceinte
close Cobalt CO154S (Figure 10)

Dimensions externes

A = 25"
B = 17,5"
C = 11,5"

Dimensions internes

A = 23,5"
B = 16"
C = 10"

Épaisseur de la cloison

Avant = 0,75"
Côté = 0,75"

— Parties du boîtier —
Forme: prisme carré
1 haut, 1 bas:

Profondeur (c) = 11,5"
Largeur (b) = 17,5"
Épaisseur = 0,75"

1 avant, 1 arrière:

Hauteur (a) = 23,5"
Profondeur (d) = 16"
Épaisseur = 0,75"
2 côtés:
Hauteur (a) = 23,5"

Profondeur (c) = 11,5"

Épaisseur = 0,75"

— Montage moteur —

Avant

Recommandations pour l'enceinte
ventilée Cobalt CO154S (Figure 11)

Dimensions externes

A = 25"
B = 17,5"
C = 13"

Dimensions internes

A = 23,5"
B = 16"

C = 11,5"

Épaisseur de la cloison

Avant = 0,75"
Côté = 0,75"

— Parties du boîtier —
Forme: prisme carré
1 haut, 1 bas:

Profondeur (c) = 13"
Largeur (b) = 17,5"
Épaisseur = 0,75"

1 avant, 1 arrière:

Hauteur (a) = 23,5"

Profondeur (d) = 16"

Épaisseur = 0,75"
2 côtés:
Hauteur (a) = 23,5"

Profondeur (c) = 13"
Épaisseur = 0,75"

— Montage moteur —

Avant

Pièces d'évent — rond
1 conduit: diamètre extérieur (e) = 4,25"

Diamètre intérieur (g) = 4"
Longueur (h) = 7"

Pièces d'évent — carré
1 haut, 1 bas:

Largeur (e) = 4,25"
Longueur (h) = 7"
Épaisseur = 0,125"

2 côtés:

Hauteur (g) = 4"
Longueur (h) = 7"

Épaisseur = 0,125"

© 2012 MD Audio Engineering—all rights

23

Modèle/Numéro de pièce MD Audio

CO104S

CO124S

CO154S
Paramètres Thiele/Small
Fs (résonance air libre, Hz)

39.2

25.6

25.2

Vas (volume d'air équivalent, pi cu)

1.080

4.017

7.098

Vas (volume d'air équivalent, litres)

30.600

113.790

201.070

Qms (facteur de qualité mécanique)

3.53

4.72

6.08

Qes (facteur de qualité électrique)

0.68

0.55

0.51

Qts (facteur de qualité total)

0.57

0.49

0.47

Re (résistance CC, ohms)

3.6

3.55

3.77

Z (impédance nominale, ohms)

4

4 4

Le (inductance, mh)

1.38

1.37

1.61

Efficacité (1W @ 1M, dB)

86.1

87.2

89.9

Xmax (déplacement de la bobine, po)

0.406

0.410

0.453

Xmax (déplacement de la bobine, mm)

10.2925

10.4075

11.5

Pe (puissance continue, watts)

200

200

250
Puissance de pointe (musique, watts)

400

500

600
Mms (masse mobile totale, grammes)

101.00

127

195
Cms (élasticité de suspension

de la membrane, mm/N)

0.180564

0.294721

0.211994

Bl (puissance du moteur, Tesla-M)

10.88

11.61

14.82

Sd (surface émissive de la
membrane, cm²)

346.361

522.792

819.398

Sd (surface émissive de la membrane, po²) 53.706

81.064

127.055

Gamme de fréquences (Hz)

39 - 250Hz 25 - 250Hz 25 - 250Hz

Produit du rendement par la
bande passante (EBP)

58

47 49

Dimensions du moteur
Encombrement du haut-parleur (pi cu)

0.048

0.061

0.116

Diamètre extérieur du haut­parleur (po/mm)

10.31/ 262 12.40/ 315

15.40/ 391

Diamètre du trou de montage (po/mm)

9.23/ 232

10.91/ 277

13.82/ 351

Profondeur de montage (po/mm)

5.12/ 130

5.51/ 140

6.46/ 164

Poids de l'aimant (oz)

38.60

41

70

Diamètre du panier (po/mm)

10.16/258 12.21/310

15.16/385
Enceintes recommandées
Enceinte close typique (pi cu)

0.75

1

2

SPÉCIFICATIONS

Spécifications sujettes à changement sans préavis

© 2012 MD Audio Engineering—all rights

25

ESPAÑOL
CARACTERÍSTICAS

15

1

2

13

3

14

4

5

12

6

7

11

10

9

8

1

Tapa de polipropileno contra el polvo; resistente a la humedad y a los

rayos ultravioleta.

2

Envolvente grande de Goma de Butadieno de Nitrilo (Nitrile Butadiene
Rubber, NBR) para grandes desplazamientos lineales controlados.

3

Cono de papel ventilado; resistente a la humedad y a los rayos
ultravioleta.

4

Armazón de acero troquelado a la medida.

5

Formador de bobina de voz Kapton ventilado (1.5 plg. para altavoces de

10 y 12 plg., 2 plg. para altavoces de 15 plg.)

6

Plancha delantera de acero de 8 mm.

7

Imanes grandes de cerámica de dos pilas.

8

Unidad de yugo en T de pieza polar y plancha trasera de acero de 8

mm.

9

Respiradero de 0.75 plg.; parte del sistema de enfriamiento de bobina de

voz mejorado (convección forzada).

10 Protector de imán de PVC.
11 Bobina de voz de 4Ω de cobre de alta temperatura.
12 Respiradero en el formador de la bobina de voz; parte del sistema de

enfriamiento de bobina de voz mejorado (convección forzada).

13 Araña Conex entrelazada con conductores de oropel bordado y

enlazado.

14 Terminales a presión.
15 Junta de montaje de PVC reversible.

26

© 2012 MD Audio Engineering—all rights

CONFIGURACIONES DE CABLEADO

Las siguientes ilustraciones contienen las pautas para conectar correctamente el woofer
Orion Cobalt a un amplificador Orion Cobalt a fin de lograr el rendimiento máximo..

Potencia de amplificador recomendada

Potencia continua (RMS)

Potencia máxima (W)

1 woofer

100 a 300

200 a 600

2 woofers

200 a 600

400 a 1200

3 woofers

300 a 900

600 a 1800

4 woofers

400 a 1200

800 a 2400

En paralelo. Dos altavoces (una bobina de voz de 4 Ω cada uno)

Dos woofers, con una bobina de voz de 4 Ω cada uno y las bobinas de voz en paralelo
producen una carga de 2 Ω en el amplificador..

1. Conecte el altavoz en paralelo conectando las dos terminales positivas (+) entre sí
y las dos terminales negativas (-) entre sí.

2. Conecte las terminales positivas (+) de los woofers a la terminal positiva (+) del
amplificador. Conecte las terminales negativas (-) de los woofers a la terminal
negativa (-) del amplificador (figura 2).

Un altavoz (una bobina de voz de 4 Ω)

Un woofer con bobina de voz de 4 Ω produce una carga de 4 Ω en el amplificador.

1. Conecte el altavoz conectando la terminal positiva (+) del woofer a la terminal
positiva (+) del amplificador. Conecte la terminal negativa (-) del woofer a la
terminal negativa (-) del amplificador (figura 3).

En serie. Dos altavoces (una bobina de voz de 4 Ω cada uno)

Dos subwoofers, con una bobina de voz de 4 Ω cada uno y las bobinas de voz en serie
producen una carga de 8 Ω en el amplificador.

1. Conecte el woofer en serie conectando la terminal negativa (-) de una de las
bobinas a la terminal positiva (+) de la otra bobina.

2. Conecte la terminal positiva (+) de la primera bobina a la terminal positiva (+) del
amplificador. Conecte la terminal negativa (-) de la segunda bobina a la terminal
negativa (-) del amplificador (figura 4).

© 2012 MD Audio Engineering—all rights

27

En serie / en paralelo. 4 altavoces (una bobina de voz de 4 Ω cada uno)

Cuatro subwoofers, con una bobina de voz de 4 Ω cada uno, las bobinas de voz
de cada par en serie y los 4 altavoces en paralelo producen una carga de 4 Ω en el
amplificador.

1. Conecte la terminal negativa (-) del altavoz 1 a la terminal negativa (-) del altavoz
3 y luego conecte esa terminal a la terminal negativa (-) del amplificador.

2. Conecte la terminal positiva (+) del altavoz 1 a la terminal negativa (-) del altavoz
2

3. Conecte la terminal positiva (+) del altavoz 3 a la terminal negativa (-) del altavoz
4

4. Conecte la terminal positiva (+) del altavoz 2 a la terminal positiva (+) del altavoz
4 y luego conecte esa terminal a la terminal positiva (+) del amplificador. (figura

5)

Consulte el diagrama de las páginas 4 - 7

RECOMENDACIONES PARA LA CAJA

Detalles de la caja

1. Las dimensiones externas se han calculado para un material de construcción de ¾
plg. de grosor

2. Incluye el desplazamiento del altavoz

3. Los volúmenes que se dan son volúmenes de sintonización neta

4. Las cajas contienen una cantidad mínima de material amortiguador. Se necesita
sólo material suficiente para recubrir la superficie interna de la caja.

28

© 2012 MD Audio Engineering—all rights

Recomendaciones para la caja
sellada Cobalt CO104S (figura 6)

Dimensiones externas
A = 14 plg.
B = 12.5 plg.
C = 11.5 plg.

Dimensiones internas
A = 12.5 plg.
B = 11 plg.
C = 10 plg.

Grosor de la pared
Delantera = 0.75 plg.
Lateral = 0.75 plg.

— Piezas de la caja —
Forma de la caja: prisma cuadrado
1 arriba, 1 abajo:
fondo (c) = 11.5 plg.
ancho (b) = 12.5 plg.
grosor = 0.75 plg.

1 adelante, 1 atrás:
altura (a) = 12.5 plg.
ancho (d) = 11 plg.
grosor = 0.75 plg.

1 a cada lado:
altura (a) = 12.5 plg.
fondo (c) = 11.5 plg.
grosor = 0.75 plg.
— Montaje del excitador —
Adelante

Recomendaciones para la caja
ventilada Cobalt CO104S (figura 7)

Dimensiones externas
A = 15.75 plg.
B = 14.25 plg.
C = 12 plg.

Dimensiones internas
A = 14.25 plg.
B = 12.75 plg.
C = 10.5 plg.

Grosor de la pared
Delantera = 0.75 plg.
Lateral = 0.75 plg.

— Piezas de la caja —
Forma de la caja: prisma cuadrado
1 arriba, 1 abajo:
fondo (c) = 12 plg.
ancho (b) = 14.25 plg.
grosor = 0.75 plg.

1 adelante, 1 atrás:
altura (a) = 14.25 plg.
ancho (d) = 12.75 plg.
grosor = 0.75 plg.

1 a cada lado:
altura (a) = 14.25 plg.
fondo (c) = 12 plg.
grosor = 0.75 plg.

— Montaje del excitador —
Adelante

Piezas del respiradero --- redondo
1 conducto: diámetro externo (e) = 3.25 plg.
diámetro interno (g) = 3 plg.
longitud (h) = 9.5 plg.

Piezas del respiradero --- cuadrado
1 arriba, 1 abajo:
ancho (e) = 3 plg.
longitud (h) = 10 plg.
grosor = 0.125 plg.

1 a cada lado:
altura (g) = 2.75 plg.
longitud (h) = 10 plg.
grosor = 0.125 plg.

Consulte el diagrama de las páginas 8 - 13

© 2012 MD Audio Engineering—all rights

29

Recomendaciones para la caja
sellada Cobalt CO124S (figura 8)

Dimensiones externas
A = 15.5 plg.
B = 14.75 plg.
C = 12 plg.

Dimensiones internas
A = 14 plg.
B = 13.25 plg.
C = 10.5 plg.

Grosor de la pared
Delantera = 0.75 plg.
Lateral = 0.75 plg.

— Piezas de la caja —
Forma de la caja: prisma cuadrado
1 arriba, 1 abajo:
fondo (c) = 12 plg.
ancho (b) = 14.75 plg.
grosor = 0.75 plg.

1 adelante, 1 atrás:
altura (a) = 14 plg.
ancho (d) = 13.25 plg.
grosor = 0.75 plg.

1 a cada lado:
altura (a) = 14 plg.
fondo (c) = 12 plg.
grosor = 0.75

Montaje del excitador
Montaje: adelante

Recomendaciones para la caja
ventilada Cobalt CO124S (figura 9)

Dimensiones externas
A = 18 plg.
B = 16.75 plg.
C = 13 plg.

Dimensiones internas
A = 16.5 plg.
B = 15.25 plg.
C = 11.5 plg.

Grosor de la pared
Delantera = 0.75 plg.
Lateral = 0.75 plg.

— Piezas de la caja —
Forma de la caj

a: prisma cuadrado
1 arriba, 1 abajo:
fondo (c) = 13 plg.
ancho (b) = 16.75 plg.
grosor = 0.75 plg.

1 adelante, 1 atrás:
altura (a) = 16.5 plg.
ancho (d) = 15.25 plg.
grosor = 0.75 plg.

1 a cada lado:
altura (a) = 16.5 plg.
fondo (c) = 13 plg.
grosor = 0.75 plg.

Montaje del excitador
Montaje: adelante

Piezas del respiradero --- redondo
1 conducto: diámetro externo (e) = 4.25 plg.
diámetro interno (g) = 4 plg.
longitud (h) = 10 plg.

Piezas del respiradero --- cuadrado
1 arriba, 1 abajo:
ancho (e) = 3.75 plg.
longitud (h) = 10 plg.
grosor = 0.125 plg.

1 a cada lado: altura
(g) = 3.5 plg. longitud
(h) = 10 plg. grosor =

0.125 plg.

30

© 2012 MD Audio Engineering—all rights

Recomendaciones para la caja
sellada Cobalt CO154S (figura 10)

Dimensiones externas
A = 25 plg.
B = 17.5 plg.
C = 11.5 plg.

Dimensiones internas
A = 23.5 plg.
B = 16 plg.
C = 10 plg.

Grosor de la pared
Delantera = 0.75 plg.
Lateral = 0.75 plg.

— Piezas de la caja —
Forma de la caja: prisma cuadrado
1 arriba, 1 abajo:
fondo (c) = 11.5 plg.
ancho (b) = 17.5 plg.
grosor = 0.75 plg.

1 adelante, 1 atrás:
altura (a) = 23.5 plg.
ancho (d) = 16 plg.
grosor = 0.75 plg.

1 a cada lado:
altura (a) = 23.5 plg.
fondo (c) = 11.5 plg.
grosor = 0.75 plg.

Montaje del excitador
Montaje: adelante

Recomendaciones para la caja
sellada Cobalt CO154S (figura 11)

Dimensiones externas
A = 25 plg.
B = 17.5 plg.
C = 13 plg.

Dimensiones internas
A = 23.5 plg.
B = 16 plg.
C = 11.5 plg.

Grosor de la pared
Delantera = 0.75 plg.
Lateral = 0.75 plg.

— Piezas de la caja —
Forma de la caja: prisma cuadrado
1 arriba, 1 a

bajo:
fondo (c) = 13 plg.
ancho (b) = 17.5 plg.
grosor = 0.75 plg.

1 adelante, 1 atrás:
altura (a) = 23.5 plg.
ancho (d) = 16 plg.
grosor = 0.75 plg.

1 a cada lado:
altura (a) = 23.5 plg.
fondo (c) = 13 plg.
grosor = 0.75 plg.

Montaje del excitador
Montaje: adelante

Piezas del respiradero --- redondo
1 conducto: diámetro externo (e) = 4.25 plg.
diámetro interno (g) = 4 plg.
longitud (h) = 7 plg.

Piezas del respiradero --- cuadrado
1 arriba, 1 abajo:
ancho (e) = 4.25 plg.
longitud (h) = 7 plg.
grosor = 0.125 plg.

1 a cada lado: altura
(g) = 4 plg. longitud
(h) = 7 plg. grosor =

0.125 plg.

© 2012 MD Audio Engineering—all rights

31

ESPECIFICACIONES

Modelo/Número de pieza dirigido

CO104S

CO124S

CO154S
Parámetros Thiele/Small
Fs (resonancia al aire libre, Hz)

39.2

25.6

25.2

Vas (cumplimiento de equivalencia, pies3) 1.080

4.017

7.098

Vas (cumplimiento de equivalencia, litros) 30.600

113.790

201.070

Qms (Q, mecánico)

3.53

4.72

6.08

Qes (Q, eléctrico)

0.68

0.55

0.51

Qts (Q total del excitador)

0.57

0.49

0.47

Re (resistencia CC, Ω)

3.6

3.55

3.77

Z (impedancia nominal, Ω)

4

4 4

Le (inductancia, mH)

1.38

1.37

1.61

Eficiencia (1 W a 1 m, dB)

86.1

87.2

89.9

Xmax (desplazamiento lineal de ida plg.) 0.406

0.410

0.453

Xmax (desplazamiento lineal de ida, mm) 10.2925

10.4075

11.5

Pe (procesamiento continuo
de potencia, W)

200

200

250

Procesamiento máximo de
potencia (música, W)

400

500

600

Mms (masa total en movimiento, g)

101.00

127

195
Cms (cumplimiento mecánico, mm/N)

0.180564

0.294721

0.211994

Bl (fuerza del motor, Tesla-m)

10.88

11.61

14.82

Sd (área de radiación efectiva, cm²)

346.361

522.792

819.398

Sd (área de radiación efectiva plg.²)

53.706

81.064

127.055

Gama de frecuencias (Hz)

39 - 250Hz 25 - 250Hz 25 - 250Hz

Producto ancho de banda energía (EBP)

58

47 49

Dimensiones físicas del excitador
Desplazamiento del altavoz (pies³)

0.048

0.061

0.116

Diámetro externo del altavoz (plg./mm)

10.31/ 262

12.40/ 315

15.40/ 391

Diámetro del agujero de
montaje (plg./mm)

9.23/ 232

10.91/ 277

13.82/ 351

Profundidad de montaje (plg./mm)

5.12/ 130

5.51/ 140

6.46/ 164

Peso del imán (oz.)

38.60

41

70

Diámetro de la canasta (plg./mm)

10.16/258

12.21/310

15.16/385
Cajas recomendadas
Caja sellada normal (pies³)

0.75

1

2

Especificaciones sujetas a cambio sin aviso previo

© 2012 MD Audio Engineering—all rights reserved

33

DEUTSCH
HÖHEPUNKTE

15

1

2

13

3

14

4

5

12

6
7

11

10

9

8

1

Feuchtigkeits- und UV-beständige Polypropylen-Abdeckung

2

Extra große Sicke aus NBR (Nitrilgummi) für linear kontrollierten

Langhub

3

Belüftete feuchtigkeits- und UV-beständige Papiermembran

4

Spezieller Stahlblechrahmen

5

Belüfteter Kapton-Schwingspulenträger (10- und 12-Zoll-Modell
verwendet 1,5-Zoll-Schwingspulenträger, 15-Zoll-Modell einen 2-Zoll-

Schwingspulenträger)

6

8-mm dickes vorderes Abdeckblech

7

Große Double-Stack-Keramikmagneten

8

8-mm dickes hinteres Abdeckblech/Polplatten-T-Stück

9

0,75-Zoll-Öffnung. Teil des verbesserten Schwingspulen-Kühlsystems

(Zwangs-Konvektion)

10

PVC-Magnetschutz

11

Hochtemperatur-Kupferschwingspule (4 Ohm)

12

Belüftung des Schwingspulenträgers. Teil des verbesserten

Schwingspulen-Kühlsystems (Zwangs-Konvektion)

13

Verknüpfte Conex-Zentriermembran mit gehefteten und geschleiften

Zuleitungslitzen

14

Druck-Terminals

15

Umkehrbare PVC-Befestigungsdichtung

34

© 2012 MD Audio Engineering—all rights reserved

SCHALTKONFIGURATIONEN

Die folgenden Abbildungen zeigen, wie Sie Ihren Orion Cobalt-Tieftöner richtig an
einen Orion Cobalt-Verstärker anschließen, um die maximale Leistung herauszuholen.

Empfohlene Verstärkerleistung

RMS-Dauerleistung

Spitzenleistung (Watt)

1 Tieftöner

100 bis 300

200 bis 600

2 Tieftöner

200 bis 600

400 bis 1200

3 Tieftöner

300 bis 900

600 bis 1800

4 Tieftöner

400 bis 1200

800 bis 2400

Parallel — Zwei Lautsprecher (4-Ohm-Schwingspulen)

Zwei parallel geschaltete Tieftöner mit 4-Ohm-Schwingspulen: Lastwiderstand von 2
Ohm am Verstärker

1. Schließen Sie den Lautsprecher parallel an, indem Sie jeweils die beiden positiven
(+) Terminals und die beiden negativen (-) Terminals miteinander verbinden.

2. Verbinden Sie die positiven (+) Terminals der Tieftöner mit dem positiven (+)

Terminal am Verstärker. Verbinden Sie die negativen (+) Terminals der Tieftöner
mit dem negativen (+) Terminal am Verstärker (abbildung 2).

Ein Lautsprecher (4-Ohm-Schwingspule)

Ein Tieftöner mit 4-Ohm-Schwingspule: Lastwiderstand von 4 Ohm am Verstärker.

1. Schließen Sie den Lautsprecher an, indem Sie das positive (+) Terminal des

Tieftöners mit dem positiven (+) Terminal am Verstärker verbinden. Verbinden
Sie das negative (-) Terminal des Tieftöners mit dem negativen (+) Terminal am
Verstärker (abbildung 3).

Reihe — Zwei Lautsprecher (Einzelne 4-Ohm-Schwingspulen)

Zwei einzelne in Reihe geschaltete Subwoofer mit 4-Ohm-Schwingspulen:
Lastwiderstand von 8 Ohm am Verstärker.

1. Schließen Sie die Tieftöner in Reihe an, indem Sie das negative (-) Terminal der

ersten Tieftöner-Schwingspule mit dem positiven (+) Terminal der zweiten Spule
verbinden.

2. Verbinden Sie das positive (+) Terminal der ersten Tieftöner-Schwingspule mit dem

positiven (+) Terminal am Verstärker. Verbinden Sie das negative (-) Terminal der
zweiten Tieftöner-Schwingspule mit dem negativen (-) Terminal am Verstärker
(abbildung 4).

© 2012 MD Audio Engineering—all rights reserved

35

Reihe/Parallel - 4 Lautsprecher (Einzelne 4-Ohm-Schwingspulen)

4 einzelne Subwoofer mit 4-Ohm-Schwingspulen, bei denen die Schwingspulen jedes
Lautsprecherpaars in Reihe geschaltet und dann alle 4 Lautsprecher parallel geschaltet
sind: Lastwiderstand von 4 Ohm am Verstärker

1. Schließen Sie das negative (-) Terminal an Lautsprecher 1 an das negative Terminal
an Lautsprecher 3 an und verbinden Sie diesen Draht mit dem negativen (-)
Terminal am Verstärker.

2. Verbinden Sie das positive (+) Terminal am Lautsprecher 1 mit dem negativen (-)
Terminal am Lautsprecher 2.

3. Verbinden Sie das positive (+) Terminal am Lautsprecher 3 mit dem negativen (-)
Terminal am Lautsprecher 4.

4. Schließen Sie das positive (+) Terminal an Lautsprecher 2 an das positive (+)
Terminal an Lautsprecher 4 an und verbinden Sie diesen Draht mit dem positiven
(+) Terminal am Verstärker (abbildung 5).

Siehe Diagramm auf Seite 4 - 7

GEHÄUSEEMPFEHLUNGEN

Gehäusedetails

1. Für Baumaterial mit ¾ Zoll (1,9 cm) Dicke berechnete Außenmaße

2. Einschließlich Lautsprecherhub

3. Angegebene Volumen sind Netto-Tuningvolumen

4. Gehäuse besitzen ein Minimum an Dämpfungsmaterial. Es ist gerade genug
Material zur Auskleidung der Innenseite des Gehäuses nötig.

36

© 2012 MD Audio Engineering—all rights reserved

Cobalt CO104S Geschlossenes Gehäuse:
Empfehlungen (abbildung 6)

Außenmaße
A = 14 Zoll (35,6 cm)
B = 12,5 Zoll (31,8 cm)
C = 11,5 Zoll (29,2 cm)

Innenmaße
A = 12,5 Zoll (31,8 cm)
B = 11 Zoll (27,9 cm)
C = 10 Zoll (25,4 cm)

Wandstärke
Vorn = 0,75 Zoll (1,9 cm)
Seite = 0,75 Zoll (1,9 cm)

— Gehäuseteile —
Gehäuseform: Quader
1 Oberseite, 1 Unterseite:
Tiefe (c) = 11,5 Zoll (29,2 cm)
Breite (b) = 12,5 Zoll (31,8 cm)
Dicke = 0,75 Zoll (1,9 cm)

1 Vorderseite, 1 Rückseite:
Höhe (a) = 12,5 Zoll (31,8 cm)
Breite (d) = 11 Zoll (27,9 cm)
Dicke = 0,75 Zoll (1,9 cm)

2 Seiten:
Höhe (a) = 12,5 Zoll (31,8 cm)
Tiefe (c) = 11,5 Zoll (29,2 cm)
Dicke = 0,75 Zoll (1,9 cm)

— Treibereinbau —
Vorn

Cobalt CO104S Bassreflex-Gehäuse:
Empfehlungen (abbildung 7)

Außenmaße
A = 15,75 Zoll (40 cm)
B = 14,25 Zoll (36,2 cm)
C = 12 Zoll (30,5 cm)

Innenmaße
A = 14,25 Zoll (36,2 cm)
B = 12,75 Zoll (32,4 cm)
C = 10,5 Zoll (26,7 cm)

Wandstärke
Vorn = 0,75 Zoll (1,9 cm)
Seite = 0,75 Zoll (1,9 cm)

— Gehäuseteile —
Gehäuseform: Quader
1 Oberseite, 1 Unterseite: Tiefe
(c) = 12 Zoll (30,5 cm) Breite (b)
= 14,25 Zoll (36,2 cm) Dicke =
0,75 Zoll (1,9 cm)

1 Vorderseite, 1 Rückseite:
Höhe (a) = 14,25 Zoll (36,2 cm)
Breite (d) = 12,75 Zoll (32,4 cm)
Dicke = 0,75 Zoll (1,9 cm)

2 Seiten:
Höhe (a) = 14,25 Zoll (36,2 cm)
Tiefe (c) = 12 Zoll (30,5 cm)
Dicke = 0,75 Zoll (1,9 cm)

— Treibereinbau —
Vorn

Öffnungsteile - Rund
1 Kanal: Außendurchmesser (e) = 3,25 Zoll
(8,3 cm)
Innendurchmesser (g) = 3 Zoll (7,6 cm)
Länge (h) = 9,5 Zoll (24,1 cm)

Öffnungsteile - Quadratisch
1 Oberseite, 1 Unterseite:
Breite (e) = 3 Zoll (7,6 cm)
Länge (h) = 10 Zoll (25,4 cm)
Dicke = 0,125 Zoll (0,3 cm)

2 Seiten:
Höhe (g) = 2,75 Zoll (7 cm)
Länge (h) = 10 Zoll (25,4 cm)
Dicke = 0,125 Zoll (0,3 cm)

Siehe Diagramm auf Seite 8 - 13

© 2012 MD Audio Engineering—all rights reserved

37

Cobalt CO124S Geschlossenes Gehäuse:
Empfehlungen (abbildung 8)

Außenmaße
A = 15,5 Zoll (39,4 cm)
B = 14,75 Zoll (37,5 cm)
C = 12 Zoll (30,5 cm)

Innenmaße
A = 14 Zoll (35,6 cm)
B = 13,25 Zoll (33,7 cm)
C = 10,5 Zoll (26,7 cm)

Wandstärke
Vorn = 0,75 Zoll (1,9 cm)
Seite = 0,75 Zoll (1,9 cm)

— Gehäuseteile —
Gehäuseform: Quader
1 Oberseite, 1 Unterseite: Tiefe
(c) = 12 Zoll (30,5 cm) Breite (b)
= 14,75 Zoll (37,5 cm) Dicke =
0,75 Zoll (1,9 cm)

1 Vorderseite, 1 Rückseite:
Höhe (a) = 14 Zoll (35,6 cm)
Breite (d) = 13,25 Zoll (33,7 cm)
Dicke = 0,75 Zoll (1,9 cm)

2 Seiten:

Höhe (a) = 14 Zoll (35,6 cm)
Tiefe (c) = 12 Zoll (30,5 cm)
Dicke = 0,75 Zoll (1,9 cm)

Treibereinbau
Einbau: Vorn

Cobalt CO124S Bassreflex-Gehäuse:
Empfehlungen (abbildung 9)

Außenmaße
A = 18 Zoll (45,7 cm)
B = 16,75 Zoll (42,5 cm)
C = 13 Zoll (33 cm)

Innenmaße
A = 16,5 Zoll (41,9 cm)
B = 15,25 Z

oll (38,7 cm)

C = 11,5 Zoll (29,2 cm)

Wandstärke
Vorn = 0,75 Zoll (1,9 cm)
Seite = 0,75 Zoll (1,9 cm)

— Gehäuseteile —
Gehäuseform: Quader
1 Oberseite, 1 Unterseite:
Tiefe (c) = 13 Zoll (33 cm)
Breite (b) = 16,75 Zoll (42,5 cm)
Dicke = 0,75 Zoll (1,9 cm)

1 Vorderseite, 1 Rückseite:
Höhe (a) = 16,5 Zoll (41,9 cm)
Breite (d) = 15,25 Zoll (38,7 cm)
Dicke = 0,75 Zoll (1,9 cm)

2 Seiten:
Höhe (a) = 16,5 Zoll (41,9 cm)
Tiefe (c) = 13 Zoll (33 cm)
Dicke = 0,75 Zoll (1,9 cm)

Treibereinbau
Einbau: Vorn

Öffnungsteile - Rund
1 Kanal:
Außendurchmesser (e) = 4,25 Zoll (10,8 cm)
Innendurchmesser (g) = 4 Zoll (10,2 cm)
Länge (h) = 10 Zoll (25,4 cm)

Öffnungsteile - Quadratisch
1 Oberseite, 1 Unterseite:
Breite (e) = 3,75 Zoll (9,5 cm)
Länge (h) = 10 Zoll (25,4 cm)
Dicke = 0,125 Zoll (0,3 cm)

2 Seiten:
Höhe (g) = 3,5 Zoll (8,9 cm)
Länge (h) = 10 Zoll (25,4 cm)
Dicke = 0,125 Zoll (0,3 cm)

38

© 2012 MD Audio Engineering—all rights reserved

Cobalt CO154S Geschlossenes Gehäuse:
Empfehlungen (abbildung 10)

Außenmaße
A = 25 Zoll (63,5 cm)
B = 17,5 Zoll (44,5 cm)
C = 11,5 Zoll (29,2 cm)

Innenmaße
A = 23,5 Zoll (59,7 cm)
B = 16 Zoll (40,6 cm)
C = 10 Zoll (25,4 cm)

Wandstärke
Vorn = 0,75 Zoll (1,9 cm)
Seite = 0,75 Zoll (1,9 cm)

— Gehäuseteile —
Gehäuseform: Quader
1 Oberseite, 1 Unterseite:
Tiefe (c) = 11,5 Zoll (29,2 cm)
Breite (b) = 17,5 Zoll (44,5 cm)
Dicke = 0,75 Zoll (1,9 cm)

1 Vorderseite, 1 Rückseite:
Höhe (a) = 23,5 Zoll (59,7 cm)
Breite (d) = 16 Zoll (40,6 cm)
Dicke = 0,75 Zoll (1,9 cm)

2 Seiten:
Höhe (a) = 23,5 Zoll (59,7 cm)
Tiefe (c) = 11,5 Zoll (29,2 cm)
Dicke = 0,75 Zoll (1,9 cm)

Treibereinbau
Einbau: Vorn

Cobalt CO154S Bassreflex-Gehäuse:
Empfehlungen (abbildung 11)

Außenmaße
A = 25 Zoll (63,5 cm)
B = 17,5 Zoll (44,5 cm)
C = 13 Zoll (33 cm)

Innenmaße
A = 23,5 Zoll (59,7 cm)
B = 16 Zoll (40,6 cm)
C = 1

1,5 Z

oll (29,2 cm)

Wandstärke
Vorn = 0,75 Zoll (1,9 cm)
Seite = 0,75 Zoll (1,9 cm)

— Gehäuseteile —
Gehäuseform: Quader
1 Oberseite, 1 Unterseite:
Tiefe (c) = 13 Zoll (33 cm)
Breite (b) = 17,5 Zoll (44,5 cm)
Dicke = 0,75 Zoll (1,9 cm)

1 Vorderseite, 1 Rückseite:
Höhe (a) = 23,5 Zoll (59,7 cm)
Breite (d) = 16 Zoll (40,6 cm)
Dicke = 0,75 Zoll (1,9 cm)

2 Seiten:
Höhe (a) = 23,5 Zoll (59,7 cm)
Tiefe (c) = 13 Zoll (33 cm)
Dicke = 0,75 Zoll (1,9 cm)

Treibereinbau
Einbau: Vorn

Öffnungsteile - Rund
1 Kanal: Außendurchmesser (e) = 4,25 Zoll
(10,8 cm)
Innendurchmesser (g) = 4 Zoll (10,2 cm)
Länge (h) = 7 Zoll (17,8 cm)

Öffnungsteile – Quadratisch 1 Oberseite, 1
Unterseite:
Breite (e) = 4,25 Zoll (10,8 cm)
Länge (h) = 7 Zoll (17,8 cm)
Dicke = 0,125 Zoll (0,3 cm)

2 Seiten:
Höhe (g) = 4 Zoll (10,2 cm)
Länge (h) = 7 Zoll (17,8 cm)
Dicke = 0,125 Zoll (0,3 cm)

© 2012 MD Audio Engineering—all rights reserved

39

DATEN

Modell/MD Audio Engineering-Teilenummer CO104S

CO124S

CO154S
Thiele/Small-Parameter
Fs (Freiluftresonanz, Hz)

39.2

25.6

25.2

Vas (Äquivalente Nachgiebigkeit, Kubikfuß) 1.080

4.017

7.098

Vas (Äquivalente Nachgiebigkeit, Liter)

30.600

113.790

201.070

Qms (Q, mechanisch)

3.53

4.72

6.08

Qes (Q, elektrisch)

0.68

0.55

0.51

Qts (totaler Treiberwert für Q)

0.57

0.49

0.47

Re (GS-Widerstand, Ohm)

3.6

3.55

3.77

Z (Nennimpedanz, Ohm)

4

4 4

Le (Induktivität, mh)

1.38

1.37

1.61

Wirkungsgrad (1 W bei 1 M, dB)

86.1

87.2

89.9

Xmax (linearer Hub in eine Richtung, Zoll)

0.406

0.410

0.453

Xmax (linearer Hub in eine Richtung, mm)

10.2925

10.4075

11.5

Pe (Dauerbelastbarkeit, Watt)

200

200

250
Spitzenbelastbarkeit (Watt)

400

500

600
Mms (Bewegte Gesamtmasse, Gramm)

101.00

127

195
Cms (mechanische Nachgiebigkeit, mm/N)

0.180564

0.294721

0.211994

Bl (Motorstärke, Tesla-M)

10.88

11.61

14.82

Sd (effektiver Strahlbereich,
Quadratzentimeter)

346.361

522.792

819.398

Sd (effektiver Strahlbereich, Quadratzoll)

53.706

81.064

127.055

Frequenzbereich (Hz)

39 - 250Hz 25 - 250Hz 25 - 250Hz

Verstärkungs-Bandbreitenprodukt (EBP)

58

47 49

Abmessungen des Treibers
Lautsprecherhub (Kubikfuß)

0.048

0.061

0.116
Lautsprecher-Außendurchmesser (Zoll/mm) 10.31/ 262 12.40/ 315 15.40/ 391
Einbaulochdurchmesser (Zoll/mm)

9.23/ 232

10.91/ 277 13.82/ 351

Einbautiefe (Zoll/mm)

5.12/ 130

5.51/ 140

6.46/ 164
Magnetgewicht (Unzen)

38.60

41

70

Korbdurchmesser (Zoll/mm)

10.16/258 12.21/310 15.16/385
Empfohlene Gehäuse
Typisches geschlossenen Gehäuse (Kubikfuß) 0.75

1

2

Daten können ohne vorherige Ankündigung geändert werden

© 2012 MD Audio Engineering—all rights

41

ITALIANO
CARATTERISTICHE

15

1

2

13

3

14

4

5

12

6
7

11

10

9

8

1

Protezione parapolvere in polipropilene - resistente all'umidità e ai

raggi ultravioletti.

2

Surround maggiorato in NBR (gomma nitrile butadiene) per lunga

escursione lineare controllata.

3

Cono aperto in carta - resistente all'umidità e ai raggi ultravioletti.

4

Telaio in acciaio stampato su misura.

5

Supporto aperto della bobina mobile in Kapton (i diffusori da 10” e 12"

usano un supporto da 1,5", quelli da 15” usano un supporto da 2").

6

Piastra anteriore in acciaio da 8 mm.

7

2 grandi magneti ceramici in cascata.

8

Piastra posteriore in acciaio da 8 mm/staffa a T per i poli.

9

Apertura da 19 mm (0,75").Parte del sistema migliorato di raffreddamento

della bobina mobile (a convezione forzata).

10

Protezione del magnete in PVC.

11

Bobina mobile da 4 ohm in rame ad alta temperatura.

12

Aperture di ventilazione del supporto della bobina mobile. Parte del
sistema migliorato di raffreddamento della bobina mobile (a convezione

forzata).

13

Centratore in Conex intrecciato con fili conduttori applicati e avvolti.

14

Terminali a pressione.

15

Guarnizione di montaggio in PVC rovesciabile.

42

© 2012 MD Audio Engineering—all rights reserved

CONFIGURAZIONI DI CABLAGGIO

Le illustrazioni seguenti presentano delle indicazioni di massima su come collegare
correttamente un woofer Orion Cobalt a un amplificatore Orion Cobalt in modo da
ottenere le massime prestazioni.

Potenza raccomandata dell'amplificatore

Potenza continua (RMS)

Potenza di picco (watt)

1 woofer

da 100 a 300

da 200 a 600

2 woofers

da 200 a 600

da 400 a 1200

3 woofers

da 300 a 900

da 600 a 1800

4 woofers

da 400 a 1200

da 800 a 2400

Due diffusori in parallelo (bobine mobili da 4 ohm)

Due woofer con bobine mobili da 4 ohm in parallelo causano un carico di 2 ohm
sull'amplificatore.

1. Collegare i diffusori in parallelo collegando tra loro i due terminali positivi (+) e i
due terminali negativi (-).

2. Collegare i terminali positivi (+) dei woofer al terminale positivo (+)
dell'amplificatore. Collegare i terminali negativi (-) dei woofer al terminale
negativo (-) dell'amplificatore (figura 2).

Un diffusore (bobina mobile da 4 ohm)

Un woofer con bobina mobile da 4 ohm causa un carico di 4 ohm sull'amplificatore.

1. Collegare il terminale positivo (+) del woofer al terminale positivo (+)
dell'amplificatore. Collegare il terminale negativo (-) del woofer al terminale
negativo (-) dell'amplificatore (figura 3).

Due diffusori in serie (con bobine mobili da 4 ohm)

Due subwoofer, ciascuno con una con bobina mobile da 4 ohm, collegati in serie
causano un carico di 8 ohm sull'amplificatore.

1. Collegare i woofer in serie collegando il terminale negativo (-) della bobina
mobile del primo woofer al terminale positivo (+) della bobina mobile del
secondo woofer.

2. Collegare il terminale positivo (+) della bobina mobile del primo woofer al
terminale positivo (+) dell'amplificatore. Collegare il terminale negativo (-) della
bobina mobile del secondo woofer al terminale negativo (-) dell'amplificatore
(figura 4).

© 2012 MD Audio Engineering—all rights

43

4 diffusori collegati in serie-parallelo (con bobine mobili da 4 ohm)

4 subwoofer con una con bobina mobile da 4 ohm ciascuno, e con le bobine mobili
di ogni coppia di diffusori collegate in serie e tutti i 4 diffusori collegati tra loro in
parallelo, causano un carico di 4 ohm sull'amplificatore.

1. Collegare il terminale negativo (-) del diffusore 1 al terminale negativo (-) del
diffusore 3 e quindi collegare il filo al terminale negativo (-) dell'amplificatore.

2. Collegare il terminale positivo (+) del diffusore 1 al terminale negativo (-) del
diffusore 2.

3. Collegare il terminale positivo (+) del diffusore 3 al terminale negativo (-) del
diffusore 4.

4. Collegare il terminale positivo (+) del diffusore 2 al terminale positivo (+) del
diffusore 4 e quindi collegare il filo al terminale positivo (+) dell'amplificatore
(figura 5).

Vedere lo schema a pagina 4 - 7

RACCOMANDAZIONI PER LA CASSA

Dettagli della cassa

1. Le misure esterne sono calcolate in base a un materiale da costruzione spesso 19
mm (0,75 in).

2. Comprendono il volume interno del diffusore.

3. I volumi indicati sono netti.

4. La cassa comprende una quantità minima di materiale di riempimento. Occorre
solo il materiale stret¬tamente sufficiente per allineare l'interno della cassa.

44

© 2012 MD Audio Engineering—all rights reserved

Raccomandazioni per la cassa
sigillata Cobalt CO104S (figura 6)

Dimensioni esterne
A = 35,5 cm (14 in)
B = 31,7 cm (12,5 in)
C = 29,2 cm (11,5 in)

Dimensioni interne
A = 31,7 cm (12,5 in)
B = 28 cm (11 in)
C = 25,4 cm (10 in)

Spessore delle pareti
Anteriore = 1,9 cm (0,75 in)
Laterale = 1,9 cm (0,75 in)

— Parti della cassa —
Forma della cassa: prisma quadrato
1 superiore, 1 inferiore:
profondità (c) = 29,2 cm (11,5 in)
larghezza (b) = 31,7 cm (12,5 in)
spessore = 1,9 cm (0,75 in)

1 anteriore, 1 posteriore
altezza (a) = 31,7 cm (12,5 in)
larghezza (d) = 28 cm (11 in)
spessore = 1,9 cm (0,75 in)

2 laterali:
altezza (a) = 31,7 cm (12,5 in)
profondità (c) = 29,2 cm (11,5 in)
spessore = 1,9 cm (0,75 in)

— Montaggio driver —
Anteriore

Vedere lo schema a pagina 8 - 13

Raccomandazioni per la cassa
aperta Cobalt CO104S (figura 7)

DDimensioni esterne
A = 31,7 cm (15,75 in)
B = 28 cm (14,25 in)
C = 25,4 cm (12 in)

Dimensioni interne
A = 31,7 cm (14,25 in)

B = 28 cm (12,75 in)

C = 25,4 cm (10,5 in)

Spessore delle pareti
Anteriore = 1,9 cm (0,75 in)
Laterale = 1,9 cm (0,75 in)

— Parti della cassa —
Forma della cassa: prisma quadrato
1 superiore, 1 inferiore:
profondità (c) = 29,2 cm (12 in)
larghezza (b) = 31,7 cm (14,25 in) = 14,25
spessore = 1,9 cm (0,75 in)

1 anteriore, 1 posteriore altezza (a) =
31,7 cm (14,25 in) larghezza (d) = 28 cm
(12,75 in) = 12,75 spessore = 1,9 cm

(0,75 in)

2 laterali:
altezza (a) = 31,7 cm (14,25 in)
profondità (c) = 29,2 cm (12 in) = 12
spessore = 1,9 cm (0,75 in)

— Montaggio driver —
Anteriore

Parti apertura --- Tonda
1 tubo: diametro esterno (e) = 8,2 cm (3,25
in)
diametro interno (g) = 7,6 cm (3 in)
lunghezza (h)

= 24 cm (9,5 in)

Parti apertura --- Quadra
1 superiore, 1 inferiore:
larghezza (e) = 7,6 cm (3 in)
lunghezza (h) = 24 cm (10 in)
spessore = 1,9 cm (0,125 in)

2 laterali:
altezza (g) = 7 cm (2,75 in)
lunghezza (h) = 24 cm (10 in)
spessore = 1,9 cm (0,125 in)

© 2012 MD Audio Engineering—all rights

45

Raccomandazioni per la cassa
sigillata Cobalt CO124S (figura 8)

Dimensioni esterne
A = 31,7 cm (15,5 in)
B = 28 cm (14,75 in)
C = 25,4 cm (12 in)

Dimensioni interne
A = 31,7 cm (14 in)
B = 28 cm (13,25 in)
C = 25,4 cm (10,5 in)

Spessore delle pareti
Anteriore = 1,9 cm (0,75 in)
Laterale = 1,9 cm (0,75 in)

— Parti della cassa —
Forma della cassa: prisma quadrato
1 superiore, 1 inferiore:
profondità (c) = 29,2 cm (12 in)
larghezza (b) = 31,7 cm (14,75 in) = 14,75
spessore = 1,9 cm (0,75 in)

1 anteriore, 1 posteriore
altezza (a) = 31,7 cm (14 in)
larghezza (d) = 28 cm (13,25 in) = 13,25
spessore = 1,9 cm (0,75 in)

2 laterali:

altezza (a) = 31,7 cm (14 in)
profondità (c) = 29,2 cm (12 in) = 12
spessore = 1,9 cm (0,75 in)

Montaggio driver
Montaggio: anteriore

Raccomandazioni per la cassa
aperta Cobalt CO124S (figura 9)

Dimensioni esterne
A = 31,7 cm (18 in)
B = 28 cm (16,75 in)
C = 25,4 cm (13 in)

Dimensioni interne
A = 31,7 cm (16,5 in)
B = 28 cm (15,25 in)
C = 25,4 cm (11,5 in)

Spessore delle pareti
Anteriore = 1,9 cm (0,75 in)
Laterale = 1,9 cm (0,75 in)

— Parti della cassa —
Forma della cassa: prisma quadrato
1 superiore, 1 inferiore:
profondità (c) = 29,2 cm (13 in)
larghezza (b) = 31,7 cm (16,75 in) = 16,75
spessore = 1,9 cm (0,75 in)

1 anteriore, 1 posteriore
altezza (a) = 31,7 cm (16,5 in)
larghezza (d) = 28 cm (15,25 in) = 15,25

spessore = 1,9 cm (0,75 in)

2 laterali:
altezza (a) = 31,7 cm (16,5 in)
profondità (c) = 29,2 cm (13 in) = 13
spessore = 1,9 cm (0,75 in)

Montaggio driver
Montaggio: anteriore

Parti apertura --- Tonda
1 tubo:
diametro esterno (e) = 8,2 cm (4,25 in)
diametro interno (g) = 7,6 cm (4 in)
lunghezza (h) = 24 cm (10 in)

Parti apertura --- Quadra
1 superiore, 1 inferiore:
larghezza (e) = 7,6 cm (3,75 in) = 3,75
lunghezza (h) = 24 cm (10 in)
spessore = 1,9 cm (0

,125 in)

2 laterali:
altezza (g) = 7 cm (3,5 in) = 3,5
lunghezza (h) = 24 cm (10 in)
spessore = 1,9 cm (0,125 in)

46

© 2012 MD Audio Engineering—all rights reserved

Raccomandazioni per la cassa
sigillata Cobalt CO154S (figura 10)

Dimensioni esterne
A = 31,7 cm (25 in)
B = 28 cm (17,5 in)
C = 25,4 cm (11,5 in)

Dimensioni interne
A = 31,7 cm (23,5 in)
B = 28 cm (16 in)
C = 25,4 cm (10 in)

Spessore delle pareti
Anteriore = 1,9 cm (0,75 in)
Laterale = 1,9 cm (0,75 in)

—Parti della cassa—
Forma della cassa: prisma quadrato
1 superiore, 1 inferiore: profondità (c)
= 29,2 cm (11,5 in) larghezza (b) = 31,7
cm (17,5 in) = 17,5 spessore = 1,9 cm
(0,75 in)

1 anteriore, 1 posteriore altezza
(a) = 31,7 cm (23,5 in) larghezza
(d) = 28 cm (16 in) = 16 spessore =
1,9 cm (0,75 in)

2 laterali:
altezza (a) = 31,7 cm (23,5 in)
profondità (c) = 29,2 cm (11,5 in) = 11,5
spessore = 1,9 cm (0,75 in)

Montaggio driver
Montaggio: anteriore

Raccomandazioni per la cassa
sigillata Cobalt CO154S (figura 11)

Dimensioni esterne
A = 31,7 cm (25 in)
B = 28 cm (17,5 in)
C = 25,4 cm (13 in)

Dimensioni interne
A = 31,7 cm (23,5 in)
B = 28 cm (16 in)
C = 2

5,4 cm (

11,5 in)

Spessore delle pareti
Anteriore = 1,9 cm (0,75 in)
Laterale = 1,9 cm (0,75 in)

—Parti della cassa—
Forma della cassa: prisma quadrato
1 superiore, 1 inferiore: profondità (c)
= 29,2 cm (13 in) larghezza (b) = 31,7
cm (17,5 in) = 17,5 spessore = 1,9 cm
(0,75 in) 1

anteriore, 1 posteriore
altezza (a) = 31,7 cm (23,5 in)
larghezza (d) = 28 cm (16 in) = 16
spessore = 1,9 cm (0,75 in)

2 laterali:
altezza (a) = 31,7 cm (23,5 in)
profondità (c) = 29,2 cm (13 in) = 13
spessore = 1,9 cm (0,75 in)

Montaggio driver
Montaggio: anteriore

Parti apertura --- Tonda
1 tubo: diametro esterno (e) = 8,2 cm (4,25
in)
diametro interno (g) = 7,6 cm (4 in)

lunghezza (h) = 24 cm (7 in)

Parti apertura --- Quadra 1 superiore, 1
inferiore:
larghezza (e) = 7,6 cm (4,25 in) = 4,25
lunghezza (h) = 24 cm (7 in)

spessore = 1,9 cm (0,125 in)

2 laterali:
altezza (g) = 7 cm (4 in) = 4,
lunghezza (h) = 24 cm (7 in)
spessore = 1,9 cm (0,125 in)

© 2012 MD Audio Engineering—all rights

47

DATI TECNICI

Modello/Codici parti

CO104S

CO124S

CO154S
Parametri Thiele/Small
Fs (freq. di risonanza in aria libera, Hz)

39.2

25.6

25.2

Vas (volume equivalente di cedevolezza, cu ft) 1.080

4.017

7.098

Vas (volume equivalente di cedevolezza, litri) 30.600

113.790

201.070

Qms (Q, meccanico)

3.53

4.72

6.08

Qes (Q, elettrico)

0.68

0.55

0.51

Qts (Q totale driver)

0.57

0.49

0.47

Re (resistenza in c.c., ohm)

3.6

3.55

3.77

Z (impedenza nominale, ohm)

4

4 4

Le (induttanza, mH)

1.38

1.37

1.61

Efficienza (1 W a 1 M, dB)

86.1

87.2

89.9

Xmax (escursione lineare monodirezionale, in) 0.406

0.410

0.453

Xmax (escursione lineare
monodirezionale, mm)

10.2925

10.4075

11.5

Pe (potenza elettrica continua, watt)

200

200

250
Potenza di picco (acustica, watt)

400

500

600
Mms (massa meccanica mobile totale, grammi) 101.00

127

195
Cms (cedevolezza meccanica, mm/N)

0.180564 0.294721 0.211994

Bl (fattore di forza elettromeccanico, Tm)

10.88

11.61

14.82

Sd (superficie radiante effettiva, cm quadrati) 346.361

522.792

819.398

Sd (superficie radiante effettiva, sq in)

53.706

81.064

127.055

Gamma di frequenza (Hz)

39 - 250Hz 25 - 250Hz 25 - 250Hz

Prodotto energia - larghezza di banda (EBP)

58

47 49

Dimensioni fisiche del driver
Volume interno del diffusore (cu ft)

0.048

0.061

0.116

Diametro esterno del diffusore
(pollici/millimetri)

10.31/ 262 12.40/ 315 15.40/ 391

Diametro fori di montaggio (pollici/millimetri) 9.23/ 232 10.91/ 277 13.82/ 351
Profondità di montaggio (pollici/millimetri)

5.12/ 130 5.51/ 140 6.46/ 164

Peso magneti (Oz)

38.60

41

70

Diametro telaio (pollici/millimetri)

10.16/258 12.21/310 15.16/385
Casse raccomandate
Cassa sigillata tipica (cu ft)

0.75

1

2

Caratteristiche soggette a modifica senza preavviso

© 2012 MD Audio Engineering—all rights reserved

49

PORTUGUÊS
CARACTERÍSTICAS

15

1

2

13

3

14

4

5

12

6
7

11

10

9

8

1

Cobertura contra pó de polipropileno resistente à umidade e radiação

ultravioleta.

2

Surround de borracha nitrílica (NBR) grande para longo deslocamento

linear controlado.

3

Cone de papel ventilado resistente à umidade e à radiação
ultravioleta.

4

Carcaça de aço estampado especial.

5

Bobina de copo Kapton ventilado (10” e 12” usam bobina de 1,5”; 15”

usa uma bobina de 2”).

6

Placa frontal de aço de 8 mm.

7

Ímãs cerâmicos grandes de duas camadas.

8

Conjunto de placa traseira/haste em T tipo forquilha de 8mm de aço

9

Abertura de ventilação de 190 mm. Parte do sistema aperfeiçoado de

arrefecimento da bobina (convecção forçada).

10

Protetor dos ímãs de PVC.

11

Bobina de cobre de alta temperatura de 4 ohm.

12

Ventilação no copo da bobina. Parte do sistema aperfeiçoado de

arrefecimento da bobina (convecção forçada).

13

Aranha Conex entrelaçada com terminais de ouropel costurados em

loop.

14

Terminais de pressão.

15

Gaxeta de instalação de PVC reversível.

50

© 2012 MD Audio Engineering—all rights reserved

CONFIGURAÇÕES DE CONEXÃO

As próximas ilustrações fornecem diretrizes sobre como conectar o woofer Orion
Cobalt a um amplificador Orion Cobalt para obter o máximo desempenho.

Potência recomendada do amplificador

Potência contínua (RMS)

Pico de potência (Watts)

1 woofer

100 a 300

200 a 600

2 woofers

200 a 600

400 a 1200

3 woofers

300 a 900

600 a 1800

4 woofers

400 a 1200

800 a 2400

Paralela – Dois alto-falantes (bobinas de 4 ohm)

Dois woofers com bobinas de 4 ohm com dois woofers em paralelo resultam em uma
carga de 2 ohm ao amplificador.

1. Conecte o alto-falante em paralelo conectando os dois terminais positivos (+)
juntos e os dois terminais negativos (-) juntos.

2. Conecte os terminais positivos (+) dos woofers ao terminal positivo (+) do
amplificador. Conecte os terminais negativos (-) dos woofers ao terminal negativo
(-) do amplificador (figura 2).

Um alto-falante (bobina de 4 ohm)

Um woofer com bobina de 4 ohm resulta em uma carga de 4 ohm ao amplificador.

1. Conecte o alto-falante unindo o terminal positivo (+) do woofer ao terminal
positivo (+) do amplificador. Conecte o terminal negativo (-) do woofer ao
terminal negativo (-) do amplificador (figura 3).

Em série – Dois alto-falantes (bobinas simples de 4 ohm)

Dois subwoofers com bobinas simples de 4 ohm conectadas em série resultam em uma
carga de 8 ohm ao amplificador.

1. Conecte os woofers em série conectando o terminal negativo (-) da bobina do
primeiro woofer ao terminal positivo (+) da bobina do segundo woofer.

2. Conecte o terminal positivo (+) da bobina do primeiro woofer ao terminal positivo
(+) do amplificador. Conecte o terminal negativo (-) da bobina do segundo
woofer ao terminal negativo (-) do amplificador (figura 4).

© 2012 MD Audio Engineering—all rights reserved

51

Em série/paralela - 4 alto-falantes (bobinas de 4 ohm simples)

Quatro subwoofers com bobinas de 4 ohm simples, com as bobinas de cada par de
alto-falantes conectadas em série e todos os quatro alto-falantes conectados em
paralelo para resultar em uma carga de 4 ohm ao amplificador.

1. Conecte o terminal negativo (-) do alto-falante 1 ao terminal negativo (-) do
alto-falante 3 e, em seguida, conecte este cabo ao terminal negativo (-) do
amplificador.

2. Conecte o terminal positivo (+) do alto-falante 1 ao terminal negativo (-) do alto­falante 2.

3. Conecte o terminal positivo (+) do alto-falante 3 ao terminal negativo (-) do alto­falante 4.

4. Conecte o terminal positivo (+) do alto-falante 2 ao terminal positivo (+) do
alto-falante 4 e, em seguida, conecte este cabo ao terminal positivo (+) do
amplificador (figura 5).

Consulte o diagrama nas páginas 4 - 7

RECOMENDAÇÕES PARA CAIXAS

Detalhes da caixa

1. Dimensões externas calculadas para material de construção de 190 mm (3/4”) de
espessura.

2. Inclui o deslocamento do alto-falante.

3. Os volumes fornecidos são volumes de sintonização sem acréscimo

4. As caixas possuem uma quantidade mínima de material abafador. É necessário ter
material suficiente para revestir a parte interna da caixa.

52

© 2012 MD Audio Engineering—all rights reserved

Recomendações para caixa selada
para Cobalt CO104S (figura 6)

Dimensões externas
A = 35,6 cm (14 pol.)
B = 31,8 cm (12,5 pol.)
C = 29,2 cm (11,5 pol.)

Dimensões internas
A = 31,8 cm (12,5 pol.)
B = 27,9 cm (11 pol.)
C = 25,4 cm (10 pol.)

Espessura da parede
Frente = 1,9 cm (0,75 pol.)
Lateral = 1,9 cm (0,75 pol.)

— Partes da caixa —
Formato da caixa: prisma quadrado
1 topo, 1 parte inferior:
comprimento (c) = 29,2 cm (11,5 pol.)
largura (b) = 31,8 cm (12,5 pol.)
espessura = 1,9 cm (0,75 pol.)

1 frente, 1 parte posterior
altura (a) = 31,8 cm (12,5 pol.)
largura (d) = 27,9 cm (11 pol.)
espessura = 1,9 cm (0,75 pol.)

2 laterais:
altura (a) = 31,8 cm (12,5 pol.)
comprimento (c) = 29,2 cm (11,5 pol.)
espessura = 1,9 cm (0,75 pol.)

— Montagem do alto-falante —
Frente

Consulte o diagrama nas páginas 8 - 13

Recomendações par

a caixa ventilada

para Cobalt CO104S (figura 7)

Dimensões externas
A = 40,0 cm (15,75 pol.)
B = 36,2 cm (14,25 pol.)
C = 30,5 cm (12 pol.)

Dimensões internas
A = 36,2 cm (14,25 pol.)
B = 32,4 cm (12,75 pol.)
C = 26,7 cm (10,5 pol.)

Espessura da parede
Frente = 1,9 cm (0,75 pol.)
Lateral = 1,9 cm (0,75 pol.)

— Partes da caixa —
Formato da caixa: prisma quadrado
1 topo, 1 parte inferior:
comprimento (c) = 30,5 cm (12 pol.)
largura (b) = 31,8 cm (14,25 pol.)
espessura = 1,9 cm (0,75 pol.)

1 frente, 1 parte posterior altura
(a) = 36,2 cm (14,25 pol.) largura
(d) = 27,9 cm (12,75 pol.)
espessura = 1,9 cm (0,75 pol.)

2 laterais:
altura (a) = 36,2 cm (14,25 pol.)
comprimento (c) = 29,2 cm (12 pol.)
espessura = 1,9 cm (0,75 pol.)

— Montagem do alto-falante —
Frente

Partes da ventilação --- Redonda
1 duto: diâmetro externo (e) = 8,3 cm (3,25
pol.)
diâmetro interno (g) = 7,6 cm (3 pol.)

comprimento (h) = 24,1 cm (9,5 pol.)

Partes da ventilação --- Quadrada
1 topo, 1 parte inferior: largura (e)
= 7,6 cm (3 pol.) comprimento (h) =
25,4 cm (10 pol.) espessura = 3,2
mm (0,125 pol.)

2 laterais:
altura (g) = 7 cm (2,75 pol.)
comprimento (h) = 25,4 cm (10 pol.)
espessura = 3,2 mm (0,125 pol.).

© 2012 MD Audio Engineering—all rights reserved

53

Recomendações para caixa selada
para Cobalt CO124S (figura 8)

Dimensões externas
A = 39,4 cm (15,5 pol.)
B = 37,5 cm (14,75 pol.)
C = 30,5 cm (12 pol.)

Dimensões internas
A = 35,6 cm (14 pol.)
B = 33,7 cm (13,25 pol.)
C = 26,7 cm (10,5 pol.)

Espessura da parede
Frente = 1,9 cm (0,75 pol.)
Lateral = 1,9 cm (0,75 pol.)

— Partes da caixa —
Formato da caixa: prisma quadrado
1 topo, 1 parte inferior:
comprimento (c) = 30,5 cm (12 pol.)
largura (b) = 31,8 cm (14,75 pol.)
espessura = 1,9 cm (0,75 pol.)

1 frente, 1 parte posterior altura
(a) = 35,6 cm (14 pol.) largura (d)
= 27,9 cm (13,25 pol.) espessura
= 1,9 cm (0,75 pol.)

2 laterais:

altura (a) = 35,6 cm (14 pol.)
comprimento (c) = 29,2 cm (12 pol.)
espessura = 1,9 cm (0,75 pol.)

Montagem do alto-falante
Montagem: Frente

Recomendações para caixa ventilada
para Cobalt CO124S (figura 9)

Dimensões externas
A = 45,7 cm (18 pol.)
B = 42,6 cm (16,75 pol.)
C = 33,0 cm (13 pol.)

Dimensões internas
A = 41,9 cm (16,5 pol.)
B = 38,7 cm (15,25 pol.)
C = 29,2 cm (11,5 pol.)

Espessura da parede
Frente = 1,9 cm (0,75 pol.)
Lateral = 1,9 cm (0,75 pol.)

— Partes da caixa —
Formato da caixa: prisma quadrado
1 topo, 1 parte inferior:
comprimento (c) = 33,0 cm (13 pol.)
largura (b) = 31,8 cm (16,75 pol.)
espessura = 1,9 cm (0,75 pol.)

1 frente, 1 parte posterior altura
(a) = 41,9 cm (16,5 pol.) largura
(d) = 27,9 cm (15,25 pol.)
espessura = 1,9 cm (0,75 pol.)

2 laterais:
altura (a) = 41,9 cm (16,5 pol.)
comprimento (c) = 29,2 cm (13 pol.)
espessura = 1,9 cm (0,75 pol.)

Montagem do alto-falante
Montagem: Frente

Partes da ventilação --- Redonda
1 duto:
diâmetro externo (e) = 10,8 cm (4,25 pol.)
diâmetro interno (g) = 10,2 cm (4 pol.)
comprimento (h) = 25,4 cm (10 pol.)

Partes da ventilação --- Quadrada
1 topo, 1 parte inferior: largura (e)
= 7,6 cm (3,75 pol.) comprimento (h)
= 25,4 cm (10 pol.) espessura = 3,2
mm (0,125 pol.)

2 laterais:
altura (g) = 7 cm (3,5 pol.)
comprimento (h) = 25,4 cm (10 pol.)
espessura = 3,2 mm (0,125 pol.)

54

© 2012 MD Audio Engineering—all rights reserved

Recomendações para caixa selada
para Cobalt CO154S (figura 10)

Dimensões externas
A = 63,5 cm (25 pol.)
B = 44,5 cm (17,5 pol.)
C = 29,2 cm (11,5 pol.)

Dimensões internas
A = 59,7 cm (23,5 pol.)
B = 40,6 cm (16 pol.)
C = 25,4 cm (10 pol.)

Espessura da parede
Frente = 1,9 cm (0,75 pol.)
Lateral = 1,9 cm (0,75 pol.)

— Partes da caixa —
Formato da caixa: prisma quadrado
1 topo, 1 parte inferior:
comprimento (c) = 29,2 cm (11,5 pol.)
largura (b) = 31,8 cm (17,5 pol.)
espessura = 1,9 cm (0,75 pol.)

1 frente, 1 parte posterior
altura (a) = 59,7 cm (23,5 pol.)
largura (d) = 27,9 cm (16 pol.)
espessura = 1,9 cm (0,75 pol.)

2 laterais:
altura (a) = 59,7 cm (23,5 pol.)
comprimento (c) = 29,2 cm (11,5 pol.)
espessura = 1,9 cm (0,75 pol.)

Montagem do alto-falante
Montagem: Frente

Recomendações para caixa ventilada
para Cobalt CO154S (figura 11)

Dimensões externas
A = 63,5 cm (25 pol.)
B = 44,5 cm (17,5 pol.)
C = 33,0 cm (13 pol.)

Dimensões internas
A = 59,7 cm (23,5 pol.)
B = 40,6 cm (16 pol.)
C = 29,2 cm (11,5 pol.)

Espessura da parede
Frente = 1,9 cm (0,75 pol.)
Lateral = 1,9 cm (0,75 pol.)

— Partes da caixa —
Formato da caixa: prisma quadrado
1 topo, 1 parte inferior:
comprimento (c) = 33 cm (13 pol.)
largura (b) = 31,8 cm (17,5 pol.)
espessura = 1,9 cm (0,75 pol.)

1 frente, 1 parte posterior
altura (a) = 59,7 cm (23,5 pol.)
largura (d) = 27,9 cm (16 pol.)
espessura = 1,9 cm (0,75 pol.)

2 laterais:
altura (a) = 59,7 cm (23,5 pol.)
comprimento (c) = 29,2 cm (13 pol.)
espessura = 1,9 cm (0,75 pol.)

Montagem do alto-falante
Montagem: Frente

Partes da ventilação --- Redonda
1 duto: diâmetro externo (e) = 10,8 cm (4,25
pol.)
diâmetro interno (g) = 10,2 cm (4 pol.)
comprimento (h) = 17,8 cm (7 pol.)

Partes da ventilação --- Quadrada
1 topo, 1 parte inferior: largura (e)
= 7,6 cm (4,25 pol.) comprimento
(h) = 17,8 cm (7 pol.) espessura =
3,2 mm (0,125 pol.)

2 laterais:
altura (g) = 7 cm (4 pol.)
comprimento (h) = 17,8 cm (7 pol.)
espessura = 3,2 mm (0,125 pol.)

© 2012 MD Audio Engineering—all rights reserved

55

ESPECIFICAÇÕES

Modelo/Número do produto

CO104S

CO124S

CO154S
Parâmetros Thiele/Small
Fs (ressonância ao ar livre, Hz)

39.2

25.6

25.2

Vas (conformidade equivalente, pés cúbicos) 1.080

4.017

7.098

Vas (conformidade equivalente, litros)

30.600

113.790

201.070

Qms (Q, mecânica)

3.53

4.72

6.08

Qes (Q, elétrica)

0.68

0.55

0.51

Qts (Q total do alto-falante)

0.57

0.49

0.47

Re (resistência à CC, ohms)

3.6

3.55

3.77

Z (impedância nominal, ohms)

4

4 4

Le (indutância, mh)

1.38

1.37

1.61

Eficiência (1 W a 1 M, dB)

86.1

87.2

89.9

Xmax (excursão linear unidirecional, pol.)

0.406

0.410

0.453

Xmax (excursão linear unidirecional, mm)

10.2925

10.4075

11.5

Pe (potência máxima permissível
contínua, watts)

200

200

250

Capacidade de processamento de
pico de potência (música, watts)

400

500

600

Mms (massa total móvel, gramas)

101.00

127

195
Cms (conformidade mecânica, mm/N)

0.180564

0.294721

0.211994

B1 (força do motor, Tesla-M)

10.88

11.61

14.82

Sd (área de radiação efetiva, cm²)

346.361

522.792

819.398

Sd (área de radiação efetiva, in²)

53.706

81.064

127.055

Faixa de freqüência (Hz)

39 - 250Hz 25 - 250Hz 25 - 250Hz

Produto de eficiência da
largura de banda (EBP)

58

47 49

Dimensão física do alto-falante
Deslocamento do alto-falante (pés cúbicos)

0.048

0.061

0.116

Diâmetro externo do alto-falante (pol./mm)

10.31/ 262 12.40/ 315 15.40/ 391

Diâmetro do orifício de montagem
do alto-falante (pol./mm)

9.23/ 232 10.91/ 277 13.82/ 351

Profundidade de instalação (pol./mm)

5.12/ 130 5.51/ 140 6.46/ 164

Peso do ímã (Oz)

38.60

41

70

Diâmetro do cone (pol./mm)

10.16/258 12.21/310 15.16/385
Caixas recomendadas
Caixa selada típica (pés cúbicos)

0.75

1

2

As especificações estão sujeitas a alteração sem aviso prévio.

-10

™

WARRANTY

LIMITED ONE-YEAR CONSUMER WARRANTY/*LIMITED TWO-YEAR CONSUMER WARRANTY FOR AUTHORIZED
MD AUDIO ENGINEERING DEALER PURCHASE & INSTALLATION

MD Audio Engineering (herein “MD Audio Engineering”) promises to the original purchaser of the subwoofer or
amplifier, as applicable (herein “Unit” or “Product”), to repair or replace with a new or refurbished Unit (at MD
Audio Engineering’s sole and absolute discretion) should the Unit prove to be defective in workmanship or material
under normal use, for a period of *two-years from the date of purchase from the authorized MD Audio Engineering
dealer PROVIDED the Unit was purchased and installed by an authorized MD Audio Engineering dealer. During this
*two-year period, there will be no charge for the repair or replacement PROVIDED the Unit is returned to MD Audio
Engineering (DO NOT RETURN THE ENTIRE ENCLOSURE. PLEASE RETURN THE WARRANTIED UNIT ONLY.), shipping
prepaid, along with the required proof of installation, the bill of sale or other dated proof of purchase, and the
consumer’s contact information. If the Unit is installed by anyone other than an authorized MD Audio Engineering
dealer, the warranty period will be one-year from the date of purchase. This warranty is non-transferable and does
not apply to any Unit that has been modified or used in a manner contrary to its intended purpose, and does not
cover damage to the Unit caused by installation or removal of the Unit. During this one-year period, there will be no
charge for the repair or replacement PROVIDED the Unit is returned to MD Audio Engineering, shipping pre-paid,
along with the bill of sale or other dated proof of purchase and the consumer’s contact information. This warranty is
void if the product has been damaged by accident or unreasonable use, neglect, improper service or other causes
not arising out of defects in materials or construction. This warranty does not cover the elimination of externally
generated static or noise, or the correction of antenna problems or weak reception, damage to speakers,
accessories, electrical systems, cosmetic damage or damage due to negligence, misuse, failure to follow operating
instructions, accidental spills or customer applied cleaners, damage due to environmental causes such as floods,
airborne fallout, chemicals, salt, hail, lightning or extreme temperatures, damage due to accidents, road hazards,
fire, theft, loss or vandalism, damage due to improper connection to equipment of another manufacturer,
modification of existing equipment, or Product which has been opened or tam- pered for any reason. Units which
are found to be damaged by abuse resulting in thermally damaged voice coils are not covered by this warranty but
may be replaced at the absolute and sole discretion of MD Audio Engineering. Unit must be returned to MD Audio
Engineering (DO NOT RETURN THE ENTIRE ENCLOSURE. THE UNIT ENCLOSURE IS COV- ERED BY A SEPARATE 90-DAY
LIMITED CONSUMER WARRANTY. PLEASE ONLY RETURN THE WARRANTIED UNIT UNLESS A WARRANTY CLAIM IS
BEING MADE FOR THE ENCLOSURE.), postage pre-paid, with bill of sale or other dated proof of purchase bearing
the following information: consumer’s name, telephone number, and address, authorized dealer’s name and
address, and product description. Unit must be returned to the following address: ATTN: WARRANTY DEPARTMENT,
MD Audio Engineering , 6941 Nw 42 St. Miami, Fl 33166. Note: This warranty does not cover labor costs for the
removal and/or reinstallation of the Unit. IN ORDER FOR THE TWO-YEAR WARRANTY TO BE VALID, YOUR UNIT
MUST BE SHIPPED WITH PROOF OF INSTALLATION BY AN AUTHORIZED MD AUDIO ENGINEERING DEALER. ALL UNITS
RECEIVED BY MD AUDIO ENGINEERING FOR WARRANTY REPAIR WITHOUT PROOF OF MD AUDIO ENGINEERING
DEALER INSTALLATION AND PURCHASE WILL BE COVERED BY THE LIMITED 1 YEAR WARRANTY.

BY PURCHASING THIS PRODUCT, ALL WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED
WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, AND WAR- RANTY OF NON­INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED TO THE MAXIMUM EXTENT ALLOWED BY
LAW, AND MD AUDIO ENGINEERING NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY
LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCT. MD AUDIO ENGINEERING HAS ABSOLUTELY NO
LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. IN NO
EVENT WILL MD AUDIO ENGINEERING BE LIABLE FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES
(INCLUDING LOSS OF PROFITS). BY PURCHASING THIS PRODUCT, THE CONSUMER AGREES AND CONSENTS THAT ALL
DISPUTES BETWEEN THE CONSUMER AND MD AUDIO ENGINEERING SHALL BE RESOLVED IN ACCORDANCE WITH
CALIFORNIA LAWS IN SAN DIEGO COUNTY, CALIFORNIA. This warranty is only valid for sale of Product within the
United States of America. Product sold outside of the United States of America is sold “AS-IS,” and shall have NO
WARRANTY, express or implied. Some states do not allow limitation on how long an implied warranty lasts. In such
states, the limitation or exclusions of this Limited Warranty may not apply. Some states do not allow the exclusion or
limitation of incidental or consequential damages. In such states, the exclusion or limitation of this Limited Warranty
may not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights which vary
from state to state. 920-0033 04-07
For more information on Orion products please visit www.orioncaraudio.com

MD Audio Engineerings is

an

ISO 9001 registered

company.

MD Audio Engineering

is

committed

to delivering

world

class

quality products

and services

that

excite and delight our

customers.

6941 Nw 42 St. Miami, Fl 33166

www.mdaudio.net

© 2012 MD Audio Engineering. All rights reserved. GCO5001 2008-10