ORing Industrial Networking Corp. RGPS-92222GCP-NP-LP, RGPS-92222GCP-NP-P Quick Installation Manual

Quick InstallationGuide

Version 1.0

Quick Installation Guide

Introduction

PRINTED ON RECYCLED PAPER

RGPS-92222GCP-NP Series

QIG

RGPS-92222GCP-NP Series

1907-2-29-RGPS92222GCPNP-1.0

The , which consist of the

and models, are managed rack-mount
Ethernet switcheswith 22 10/100/1000Base-T(X)IEEE802.3at P.S.E.
ports, twoGigabit combo ports,and two 100/1000Base-XSFP ports. The
P.S.E-enabledports are ableto provide sufficientpower for power-hungry
devices withup to 30w per port. With dual powerinputs for redundancy,
the switcheshave an operatingtemperature from -40 C to 60 C.

RGS-92222GCP-NP series RGPS-92222GCP-

NP-LP RGPS-92222GCP-NP-P

oo

Preparation

Before youbegin installing theswitch, make sureyou have allof the package
contents availableand a PCwith Microsoft InternetExplorer 6.0 orlater, for
using web-basedsystem management tools.

Elevated OperatingAmbient:

ReducedAir Flow:

Mechanical Loading:

Circuit Overloading:

If installed in a closed or multi-unit rack
assembly,the operating ambienttemperature of therack environment maybe
greater thanroom ambient. Therefore,consideration should begiven to
installing theequipment in anenvironment compatible withthe maximum
ambient temperature(Tma) specified bythe manufacturer.

Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.

Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.

Consideration shouldbe given tothe connection ofthe
equipment tothe supply circuitand the effectthat overloading ofthe circuits
might haveon overcurrent protectionand supply wiring.Appropriate
consideration ofequipment nameplate ratingsshould be used when addressing
this concern.

Safety & Warnings

Dimension

Panel Layouts

1. Consoleport

2. Resetbutton

3. Powerindicator

4. Ringstatus LED

5. RMstatus LED

6. Faultindicator

7. LANports

Front View

Rear View

Installation

Rack-mounting

Step 1:

Step 2:

Install leftand right frontmounting brackets tothe switch usingthree screws on each side.

With frontbrackets orientated infront of therack, fasten thebrackets to therack using twomore

screws.

Network Connection

Console cable

Use theprovided DB-9 cable(RS-232 cable) toconnect the switchto a PCwith the DB-9
connector attachedto the switchconsole port andthe DB-9 femaleconnector to thePC.

PC pin out (mal e)

assignment

RS-232 wit h DB9

female connect or

Pin#2RD Pin#2TD

Pin #3TD Pin #3 RD

Pin #5GND Pin #5GND

Package Contents

Contents

QIG

CD

Console Cable

Screw (M4X6)

Powercord

Rack-mounted
kit(L&R)

Number

X1

X1

X1

X6

X1

X1

RGPS-92222­GCP-NP

Pictures

MANAGED

Rack-Mount

GIGABIT

SWITCH

PoE

Managed Gigabit PoE Ethernet Switch

X1

35.50

44.00

8.00

20.00

24.00

32.0

5.50

R3.25

25.50

2.50

4.30

17.80

30.20 82.00

342.00

86.5

ACPowerSWITCH

49.0

3.0

AC100-240V

50-60HZ

PW1

44.00

431.00

G2 G4 G6 G8

G1 G3 G5 G7

LINK/ACT

Console

G23 G24 G25 G26

RGPS-92222GCP-NP

R.M.

Ring

Reset

10/100/
1000T

Fault

G1G2G7G8G9

G10

G15

G16

G17

G18

G23

G24

PoE

100/1000X

G10 G12 G14 G16

G9 G11 G13 G15

G18 G20 G22

G17 G19 G21 G23

G24

PWR

G2 G4 G6 G8

G1 G3 G5 G7

LINK/ACT

Console

G23 G24 G25 G26

RGPS-92222GCP-NP

R.M.

Ring

Reset

10/100/
1000T

Fault

G1G2G7G8G9

G10

G15

G16

G17

G18

G23

G24

PoE

100/1000X

G10 G12 G14 G16

G9 G11 G13 G15

G18 G20 G22

G17 G19 G21 G23

G24

PWR

1

2 3 4 5 6 7

8 9

10

11 12

13 14

8. LEDfor even Ethernetports link/act status

9. LEDfor odd Ethernetports link/act status

10. FirstGigabit combo port

11. SecondGigabit combo port

12. PoEstatus LED forLAN ports

13. SFPports

14. LNK/ACTLED for SFPports

ACPowerSWITCH

AC100-240V

50-60HZ

PW1

1 2

1. Powerswitch

2. ACpower input (100V~240V
/ 50~60Hz)

The switchprovides standard Ethernet ports.According tothe link type,the switch uses CAT
3,4,5,5e UTP cables to connect to any other network devices (PCs, servers, switches,
routers, or hubs). Please refer to the following table for cable specifications.

Cable Typesand Specifications:

Cable Type Max. Length Conne ctor

10BASE-T Cat. 3, 4,5 100-ohm UTP 100m (328 ft) RJ-45

100BASE-TX Cat. 5 100-ohmUTP UTP100 m(328 ft) RJ-45

1000BASE- T Cat.5 / Cat.5e 100-o hmUTP UTP 100 m(328 ft) RJ-45

With 10/100BASE-T(X)cables, pins 1and 2 areused for transmittingdata, and pins3 and 6are
used forreceiving data. Thedevice also supportsauto MDI/MDI-X operation.You canuse a
cable toconnect the switchto a PC

For pinassignments for differenttypes of cables,please refer tothe following
tables.

10/100 Base-T(X) MDI/MDI-X

Pin Number MD Iport MDI -Xport

1TD+(transmit)RD+(receive)

2TD-(transmit)RD-(receive)

3 RD+(receive) TD+(transmit)

4NotusedNotused

5NotusedNotused

6 RD- (receive) TD- (transmit)

7NotusedNotused

8NotusedNotused

1000Base- TMDI/MD I-X

Pin NumberMDI portMDI-X port

1 BI_DA+ BI_DB+

2 BI _DA- BI _DB-

3 BI_DB+ BI_DA+

4 BI_DC+ BI_DD+

5 BI _DC- B I_DD-

6 BI _DB- B I_DA-

7 BI_DD+ BI_DC+

8 BI_DD - BI_ DC-

10/100Base-T( X) P.S.E. RJ-45 por t

PinNumber Assi gn men t

#1 TD+wit h PoE Power in put +

#2

TD- with PoE Power inp ut +

#3

RD+ with PoE Power i nput -

#6

RD- with PoE P ower inp ut -

1000Base-T P.S.E. RJ- 45 port

PinNumber Assignment

#1 BI_DA+ with P oE Power input +

#2

BI_DA- with PoE P ower input +

#3

BI_DB+ wit h PoE Power in put -

#4

BI_DC+

#5

BI_DC-

#6

BI_DB- wit h PoE Power in put -

#7

BI_DD+

#8

BI_DD-

QIG

Quick InstallationGuide

PRINTED ON RECYCLED PAPER

Version 1.0

Quick Installation Guide

Configurations

After installingthe switch andconnecting cables, startthe switch by
turning onpower. Thegreen power LEDshould turn on.

LED indication table

1. Launchthe Internet Explorerand type inIP address ofthe switch.The

default staticIP address is192.168.10.1

2. Login with defaultuser name andpassword (both are ). After
logging in,you should see the following screen. For more information
on configurations, please referto the usermanual. For informationon
operating theswitch using ORing’sOpen-Vision management utility, please
go toORing website.

admin

Resetting

Toreboot the switch,press the button for5 seconds.

Torestore the switchconfigurations back tothe factory defaults,press the
button for10 seconds.

Reset

Reset

Specifications

ORingSwitch Model

PhysicalPorts

Technology

EthernetStandards

LEDIndicators

10/100/1000Base-T(X)with
P.S.E.PortsinRJ45Auto
MDI/MDIX

RS-232Serial Console Port

SwitchProperties

SecurityFeatures

DeviceBinding security feature
Enable/disableports, MAC basedport security
Portbased network accesscontrol (802.1x)
Single802.1x and Multiple802.1x
MAC-basedauthentication
QoSassignment
GuestVLAN
MACaddresslimit
TACACS+
VLAN(802.1Q) to segregatean secure networktraffic
Radiuscentralized password management
SNMPv3encrypted authentication andaccess security
Https/ SSH enhancenetwork security
Weband CLI authenticationand authorization
Authorization(15 levels)
IPsource guard

SoftwareFeatures

IEEE802.1D Bridge, autoMAC address learning/agingand MAC address(static)
MultipleRegistration Protocol (MRP)
MSTP RSTP/STP compatible)
RedundantRing (O-Ring) withrecovery time lessthan 30ms over250 units
TOS/Diffservsupported
Qualityof Service (802.1p)for real-time traffic
VLAN(802.1Q) with VLANtagging
IGMPv2/v3 Snooping
IP-basedbandwidth management
Application-basedQoS management
DOS/DDOSauto prevention
Portconfiguration, status, statistics,monitoring, security
DHCPServer/Client
DHCPRelay
ModbusTCP
DNSclient proxy

(

NetworkRedundancy

O-Ring,Open-Ring, O-Chain, MRP,MSTP (RST/PSTPcompatible)

RS-232in DB-9 connectorwith console cable. 115200bps, 8, N, 1

RGPS-92222GCP-NP-LP

22

IEEE802.3 for 10Base-T,IEEE 802.3ufor 100Base-TXand 100Base-FX,
IEEE802.3z for 1000Base-X,
IEEE802.3ab for 1000Base-T,
IEEE802.3ae for 10GigabitEthernet
IEEE802.3x for Flowcontrol,
IEEE802.3ad for LACP(Link Aggregation ControlProtocol )
IEEE802.1p for COS(Class of Service)
IEEE802.1Q for VLANTagging
IEEE802.1w for RSTP(Rapid Spanning TreeProtocol)
IEEE802.1s for MSTP(Multiple Spanning TreeProtocol)
IEEE802.1x for Authentication
IEEE802.1AB for LLDP(Link Layer DiscoveryProtocol)
IEEE802.3atPoEspecification(upto30WattsperportforP.S.E.)

RGPS-92222GCP-NP-LP: Total powerbudget is 320Watts
RGPS-92222GCP-NP-P: Total powerbudget is 720Watts

Switchlatency: 7 us
Switchbandwidth: 48Gbps
Max.Number of AvailableVLANs: 256
IGMPmulticast groups: 128for each VLAN
Portrate limiting: UserDefine

MACTable

8K

Processing

Store-and-Forward

PriorityQueues

8

Amber: Indicate unexpectedevent occurred

FaultIndicator (Fault)

O-RingIndicator (Ring)

Green:FlashingtoindicatesystemoperatedinO-RingMastermodeRingMaster Indicator (R.M.)

Green: Indicates thatthe system operatingin O-Ring mode
GreenBlinking : Indicatesthat the Ringis broken.

Jumboframe Upto 9.6K Bytes

Green: Power indicatorPowerIndicator (PWR1/PWR2)

10/100/1000Base-T(X)RJ45
PortIndicator

Power

Powerconsumption(Typ.)

37Watts (P.D.not included)

Overloadcurrent protection

Present

Greenfor Link/Act indicatorat 1Gbps
Amberfor Linl/Act indicatorat 10/100Mbps

PoEIndicator

Green:PoEenabledLEDx24

100/1000Base-XSFP Port
Indicator

Green:forSFPLink/Actindicator

Overloadcurrent protection

100~240VACwith power socket

Environmental

-40to85C(-40to185F)

oo

StorageTemperature

OperatingTemperature

PhysicalCharacteristic

Dimension(WxDxH)

Weight (g)

5000g

5%to 95% Non-condensing

OperatingHumidity

RegulatoryApprovals

Enclosure

19inches rack mountable

5730g

431(W)x342(D)x44(H)mm(16.97x13.47x1.73inches)

FCCPart 15, CISPR(EN55022) class AEMI

EN61000-4-2(ESD)
EN61000-4-3(RS)
EN61000-4-4(EFT)
EN61000-4-5(Surge)
EN61000-4-6(CS)
EN61000-4-8
EN61000-4-11

EMS

Warranty

5years

Warranty

5years

LED Color Status Descripti on

Green On S ystem power on

PWR

Green Blinking Upgrading f irmware

R.M Green On RingMaster

On R ing enabled

Ring Green

Blinking Ring struct ure is broken

Fault Amber On Errors(For portmalfunctioning)

10/100/1000Base -T(X) RJ45 por t

On P ort connected a t 1Gbps

Green

Blinking Transmitting data

On

Port connect ed at 10/100M bps

Link/Act

Amber

Blinking

Transmitting data

PoE Green On PoE- enabled

100/1000Base-X S FP port

On P ort connected

Link/Act Green

Blinking Transmitting data

RGPS-92222GCP-NP Series

RGPS-92222GCP-NP Series

MANAGED

Rack-Mount

GIGABIT

SWITCH

PoE

Managed Gigabit PoE Ethernet Switch

ORing IndustrialNetworking Corp.

Copyright© 2014 ORing

All rightsreserved.

TEL: [phone]
FAX:[phone]

Website: www.oring-networking.com
E-mail: [e-mail]

RGPS-92222GCP-NP-P

GigabitCombo port with
10/100/1000Base-T(X)P.S.E.
and100/1000Base-X SFP ports

2

100/1000Base-Xwith SFP port

2

Powersupply

450Watts power supplyincluded (320W powerbudget) 1000Watts powersupply included (720Wpower budget)

-40to60C(-40to140F)

oo

IEC60068-2-27Shock

IEC60068-2-32FreeFall

IEC60068-2-6Vibration

EN60950-1Safety