Page 1
Quick InstallationGuide
Version 1.0
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
QIG
ITGMC-111GP+
1907-2-29-ITGMC111GP+-1.0
The is acost-effective solution forinterface conversion
between 1G/10GBase-Tand 1G/10GBase-X SFP+ socket. It allowsyou to
extend communicationdistance of Gigabitcopper port withoptical fiber.The
supports MDI/MDIXauto detection, soyou don’t needto use
crossover wires. With a wide operating temperaturerange from -20~60 C
and awide voltage rangefrom dual 12~48 VDC power inputs, the
is suitablefor harsh operatingenvironments. Therefore,the
is oneof the mostreliable media convertersin harsh industrial
environments.
ITGMC-111GP+
ITGMC-111GP+
ITGMC111GP+ ITGMC111GP +
o
Package Contents
Installation
The series isshipped with thefollowing items. Ifany of theseitems is missing
or damaged,please contact yourcustomer service representativefor
assistance.
Preparation
Before installation, makesure you have all of the package contents
available and a PC with MicrosoftInternet Explorer 6.0 or later, forusing
web-based system management tools.
Elevated OperatingAmbient:
ReducedAir Flow:
If installed in a closed cabinet, theoperating
ambient temperatureof the rackenvironment may begreater than roomambient.
Therefore, considerationshould be givento installing theequipment in an
environment compatiblewith the maximumambient temperature (Tma)specified
by themanufacturer.
Installation of the equipment should be such that the
amount of air flow required for safe operation of the equipment is not
compromised.
Mechanical Loading:
Circuit Overloading:
Mounting of the equipment in the d should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Consideration shouldbe given tothe connection ofthe
equipment tothe supply circuitand the effectthat overloading ofthe circuits
might haveon overcurrent protectionand supply wiring.Appropriate
consideration ofequipment nameplate ratingsshould be used when addressing
this concern.
in-rail
Safety & Warnings
Dimension (Unit: mm)
Step 1:
Step 2:
Slant the switch and screwthe Din-railkit onto theback of theswitch, right in the
middle of the back panel.
Slide theswitch ontoa DIN-rail fromthe Din-rail kitand make surethe switch clicksinto
the railfirmly.
DIN-rail Installation
Media
Converter
Media
Converter
INDUSTRIAL
ITGMC-111GP+
Panel Layouts
Front Panel
1. PowerLED
2. RelayLED
3. DIPswitch for relay
4. LNK/ACTLED for 10Gcopper port
5. 10Gport
6. SpeedLED for 10GSFP port
7. LNK/ACTLED for 10GSFP port
8. 10GSFP port
TopPanel
2
1. Terminalblock
2. Grounding
Real Panel
1. Wall-mountscrew holes
2. Din-railscrew holes
1
3
Industrial Gigabit Media Converter
Contents
ITGMC-111GP+
Pictures Number
X1
QIG
X1
DIN-railkit
X1
Wall-MountKit
X2
ITGMC-111GP+
2
4
5
6
7
8
1
1
1
2
Wall-mount
Step 1:
Step 2:
Step 3:
Screw thetwo pieces ofwall-mount kits to the topand bottom panels of the device. A
total of screws are required, as shown below.
Use thedevice, with wall mount plates attached, asa guide tomark the correctlocations
of thefour screws.
Insert ascrew head through middle of thekeyhole-shaped aperture on the plate, and
then slide the device downwards. Tightenthe screwhead for added stability.
eight
Network Connection
The device has two 10/100Base-T(X) Ethernet ports. According to the link type, the AP uses
CAT 3, 4, 5, 5e, 6 UTP cables to connect to any other network device (PCs, servers,
switches, routers, or hubs).
Cable Typesand Specifications:
Cable
Type
Max.Length
Connector
10BASE-T Cat.3, 4, 5100-o hm UTP 100m (328 ft) RJ-45
100BASE-T X Cat. 5100 -ohmUTP UTP 100 m( 328ft) RJ -45
Page 2
QIG
Quick InstallationGuide
PRINTED ON RECYCLED PAPER
Quick Installation Guide
Power Input
The switch supports triple redundant power supplies which are
located on a 7-pin terminal block.
Insert the negative/positive wires into the V-/V+ terminals,
respectively.
To keep the DC wires from pulling loose, use a small flat-
blade screwdriver totighten the wire-clampscrews on thefront of the
terminal blockconnector.
STEP 1:
STEP 2:
Version 1.0
QIG
Configurations
After installingthe device and connecting cables, the greenpower LED
should turnon. Please referto the followingtablet for LEDindication.
LED indication table
Specifications
Wiring
For pinassignments for differenttypes of cables,please refer tothe following tables.
Media
Converter
Media
Converter
INDUSTRIAL
ORing MediaConverter Model
ITGMC-111GP+
1G/10GBase-Tin RJ45 Auto
MDI/MDIX
Physical Ports
Technology
Ethernet standards
IEEE 802.3aefor 10Gigabit Ethernet
IEEE 802.3anfor 10GBase-T
IEEE 802.3abfor 1000Base-T
IEEE 802.3zfor 1000Base-X
Power
Input power
Power consumption(Typ.)
Dual12~48VDCvoltagepowerinputsin6pinterminalblock
8.6 Watts
Overload currentprotection
Reversepolarity protection
Present
Present onterminal block
Physical Characteristic
Enclosure
IP-30
Dimension(WxDxH)
40(W)x108(D)x154(H)mm(1.57x4.25x6.02inch)
Weight (g)
1
(*Note)
Jumbo Frame
10K
437g
Fault contact
Relay
Relayoutputtocarrycapacityof1Aat24VDCatpinterminalblock
Regulatory Approvals
FCC Part15, CISPR(EN55022) class A
EMI
EN61000-4-2 (ESD),EN61000-4-3 (RS), EN61000-4-4(EFT), EN61000-4-5 (Surge),
EN61000-4-6 (CS),EN61000-4-8, EN61000-4-11
EMS
IEC60068-2-27
Shock
IEC60068-2-6
IEC60068-2-32
Vibration
Free Fall
100/1000Base-XSFP port
1
Environmental
-40to85C(-40to185 F)
oo
Storage Temperature
Operating Temperature
5% to95% Non-condensing
Operating Humidity
-20to60C(-4to140F)
oo
MTBF
TBD
Warranty
5years
1G/10G Base-T(X) RJ-45 Pin Assignments
Pin Number
Assignment
1TD+
2TD-
3RD+
4Notused
5Notused
6RD-
7Notused
8Notused
1G/10G B ase-T MDI /MDI-X Pin A ssignmen ts
Pin Number
MDI port
MDI-X port
1 TD +(transmit) RD+(receive)
2 TD-(transmit) RD-(receive)
3 RD+(receive) TD+(transmit )
4 Not used Not used
5 Not used Not used
6 RD-(receive) T D-(transmit)
7 Not used Not used
8 Not used Not used
Fiber Cables
The device comes witha SFP fiberoptical port. Thefiber optical ports arein multimode (0to 550M, 850 nm with50/125 m,62.5/125 m fiber)and single-mode with
LC connectors.Please remember thatthe TX portof SwitchA should beconnected to
the RXport of SwitchB.
LED
Color
Status
Descript ion
PW1 Green On DC power module 1activated
PW2
Green
On DC powermo dule2 activated
Relay Amber
On Relay activated(closed)
Off Rel ay de-activated(opened)
LED forSFP Port
LNK/ACT Green On Portis linked
LEDfor RJ45Port
LNK/ACT Green On Portis linked
Speed
Green On Portis runningat 10Gbps
Amber On Port isrunning at1Gbps
ORing IndustrialNetworking Corp.
Copyright© 2017 ORing
All rightsreserved.
TEL: +886-2-2218-1066
FAX:+886-2-2218-1014
Website: www.oring-networking.com
E-mail: [email protected]
*Note:10GBase-TmustuseshieldingtwistedpaircableofCat6aorabove.
ITGMC-111GP+
ITGMC-111GP+
Industrial Gigabit Media Converter
Loading...