ORiNG IGS-9084GP-FB2 Quick Installation Manual

Download

Page 1

IGS-9084GP-FB2

PWR

PWR1

PWR2

10/100/1000T

G12

G11

G10

100/1000X

Quick InstallationGuide

Version 1.0

Quick Installation Guide

Introduction

PRINTED ON RECYCLED PAPER

The series isa managed industrialEthernet switch with eight 10/100/1000Base-T(X)ports and four100/1000Base-X SFP ports.With fiber opticalbypass design, theswitch can ensurecontinued network operation whenany inline deviceon the networkfails. The switchsupports Ethernet Redundancyprotocol, O-Ring (recoverytime < 30msover 250 units of connection)and MSTP (RSTP/STPcompatible) to protectmission-critical applications fromnetwork interruptions ortemporary malfunctions withfast recovery technology. Witha wide operatingtemperature from -40 Cto 70 C, the devicecan be managedcentrally via ORing’sproprietary Open-Vision management utiltyas well asvia Web-based interfaces,Telnet, andconsole (CLI). Theswitch is oneof the mostreliable choices forhighly-managed and fiber Ethernetapplications.

IGS-9084GP-FB2

Preparation

Before youbegin installing theswitch, make sureyou have allof the package contents availableand a PCwith Microsoft InternetExplorer 6.0 orlater, for using web-basedsystem management tools.

Elevated OperatingAmbient:

ReducedAir Flow:

Mechanical Loading:

If installed in a closed or multi-unit rack assembly,the operating ambienttemperature of therack environment maybe greater thanroom ambient. Therefore,consideration should begiven to installing theequipment in anenvironment compatible withthe maximum ambient temperature(Tma) specified bythe manufacturer.

Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.

Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.

Safety & Warnings

Dimension

Panel Layouts

1. PowerLED

2. PWR1LED

3. PWR2LED

4. R.M.status LED

5. Ringstatus LED

6. Faultyrelay indicator

7. SFPport

8. Link/actionLED for Gigabit Ethernetports

Package Contents

Contents

DIN-rail Kit

IGS-9084GP-FB2

Pictures Number

Front View

TopPanel

The device is shippedwith the followingitems. If anyof these itemsis missing ordamaged, please contactyour customer servicerepresentative for assistance.

GIGABIT

INDUSTRIAL

SWITCH

Industrial Managed Gigabit Switch

QIG

Console Cable

Wall-mountKit

33.0

30.0

12.5

105.5

10.9

15.0

70.5

154.0

96.4

87.0

48.0

17.5

94.0

124.0

48.0

58.0

7.50

R2.5

R3.95

80.5

62.0

87.9

1 2 3 4 5 6

Rear View

PWR-1PWR-2

1A@24V

DC48V

V2-V2+ V1-V1+

Fault

1. Wall-mountscrew holes

2. Din-railscrew holes

1. Terminalblocks: PWR1, PWR2 (12-48V DC),Relay

2. Groundwire.

Installation

Step 1:

Step 2:

Slant the switch and screwthe Din-railkit onto theback of theswitch, right in the

middle of the back panel.

Slide theswitch ontoa DIN-rail fromthe Din-rail kitand make surethe switch clicks

into therail firmly.

DIN-rail Installation

Step 1:

Step 2:

Step 3:

Screw the twopieces of wall-mount kits onto bothends of the rear panel ofthe

switch. A total of six screws are required,as shown below.

Use the switch,with wall mount plates attached, as a guide to mark the

correct locations of the four screws.

Insert a screwhead through the large parts ofthe keyhole-shaped apertures,

and then slidethe switch downwards. Tighten thescrews for added stability.

Wall-mounting

QIG

1907-2-29-IGS9084GPFB2-1.0

Circuit Overloading:Consideration should begiven to theconnection of theequipment to the

supply circuitand the effectthat overloading ofthe circuits mighthave on overcurrentprotection and supplywiring. Appropriateconsideration of equipmentnameplate ratings shouldbe used when addressingthis concern.

Network Connection

Network

Monitor

9. DuplexLED for Gigabit Ethernet ports

10. GigabitEthernet ports

11. Link/actionLED for SFPport

12. Bypassnetwork port

13. Bypassmonitor port

14. Consoleport

15. Resetbutton

IGS-9084GP-FB2

PWR

PWR1

PWR2

10/100/1000T

G12

G11

G10

100/1000X

Network

Monitor

IGS-9084GP-FB2

PWR

PWR1

PWR2

10/100/1000T

G12

G11

G10

100/1000X

Network

Monitor

The switchprovides standard Ethernet ports. According to the link type, the switch uses CAT 3,4, 5, 5e UTP cables to connect to any other network devices (PCs, servers, switches, routers, or hubs). Please refer to the following table for cable specifications.

Cable Typesand Specifications:

Cable Type Max. Length Conne ctor

10BASE-T Cat. 3, 4,5 100-ohm UTP 100m (328 ft) RJ-45

100BASE-TX Cat. 5100-ohmUTP UTP 100m(328 ft) RJ-45

1000BASE- T Cat. 5 /Cat. 5e 100-ohm UTP UTP1 00m (328 ft) R J-45

IGS-9084GP-FB2

Page 2

QIG

Quick InstallationGuide

PRINTED ON RECYCLED PAPER

Version 1.0

Quick Installation Guide

Resetting

Toreboot the switch,press the button for2-3 seconds.

Torestore the switchconfigurations back tothe factory defaults,press the buttonfor 5 seconds.

Reset

Specifications

GIGABIT

INDUSTRIAL

SWITCH

Industrial Managed Gigabit Switch

For pinassignments for differenttypes of cables,please refer tothe following tables.

10/100 Base-T(X)MDI/MDI-X

Pin Number MDI port MDI-X port

1TD+(transmit)RD+(receive)

2TD-(transmit)RD-(receive)

3 RD+(receive) TD+(transmit)

4NotusedNotused

5NotusedNotused

6 RD-(receive) TD-(transmit)

7NotusedNotused

8NotusedNotused

Note: “+”and “-” signsrepresent the polarityof the wiresthat make upeach

wire pair.

Toconnect the consoleport to anexternal management device,you need anRJ-45 to DB-9 cable,which is alsosupplied in thepackage. Below isthe console portpin assignment information.

Console PortPin Definition

PC (male) pi n assignment

RS-232 with DB9 (female) pin

assignment (RJ45-D B9 cable)

RJ45 pin as signment

PIN#2RxD PIN#2RxD PIN#2RxD

PIN#3TxD PIN#3TxD PIN#3TxD

PIN#5GND PIN#5GND PIN#5 GND

Wiring

The switch supports dual redundant power supplies, Power Supply1 (PWR1) and Power Supply2 (PWR2). Theconnections for PWR1, PWR2 andthe RELAYare located onthe terminal block.

Insert the negative/positive wires into the V-/V+ terminals,

respectively.

To keep the DC wires from pulling loose, use a small flatblade screwdriverto tighten thewire-clamp screws onthe front ofthe terminal blockconnector.

STEP 1:

STEP 2:

PWR-1PWR-2

1A@24V

V2-V2+ V1-V1+

Fault

Power inputs

The twosets of relaycontacts of the6-pin terminal blockconnector are usedto detect user-configured events. Thetwo wires attachedto the faultcontacts form anopen circuit whena user-configured when an eventis triggered. Ifa user-configured eventdoes not occur,the faultcircuit remains closed.

Relay contact

Grounding andwire routing helplimit the effectsof noise dueto electromagnetic interference(EMI). Run theground connection fromthe ground screwsto the groundingsurface prior toconnecting devices.

Grounding

Configurations

After installingthe switch, thegreen power LEDshould turn on.Please refer tothe following tabletfor LED indication.

1. Launchthe Internet Explorerand type inIP address ofthe switch.The default staticIP address is

192.168.10.1

2. Login with defaultuser name andpassword (both are ). After loggingin, you should see the following screen. For more information on configurations, please referto the user manual. Forinformation on operatingthe switch using ORing’sOpen-Vision management utility, please goto ORing website.

admin

Follow thesteps to setup the switch:

ORingSwitchModel

IGS-9084GP-FB2-SS

PhysicalPorts

Technology

EthernetStandards

IEEE802.3 for 10Base-T IEEE802.3u for 100Base-TXand 100Base-FX IEEE802.3z for 1000Base-X IEEE802.3ab for 1000Base-T IEEE802.3ad for LACP(Link Aggregation ControlProtocol) IEEE802.3x for Flowcontrol, IEEE 802.1Dfor STP (SpanningTree Protocol) IEEE802.1p for COS(Class of service) IEEE802.1Q for VLANTagging IEEE802.1w for RSTP(Rapid Spanning TreeProtocol IEEE802.1s for MSTP(Multiple Spanning TreeProtocol) IEEE802.1x for Authentication

Power

RedundantInput power

Powerconsumption(Typ.)

DualDC inputs. 12-48VDCon 6-pin terminalblock

13watts max.

Overloadcurrent protection

Present

PhysicalCharacteristic

Enclosure

IP-30

Dimension(WxDxH)

96.4(W) x 105.5(D)x 154(H) mm(3.8 x 4.15x 6.06 inch)

10/100/1000Base-T(X)Ports inRJ45 Auto MDI/MDIX

MACTable

RS-232Serial Console Port

PriorityQueues

Processing

Store-and-Forward

SwitchProperties

Switchlatency: 7 us Switchbandwidth: 24Gbps Max.Number of AvailableVLANs: 256 IGMPmulticast groups: 128for each VLAN Portrate limiting: UserDefine

SecurityFeatures

DeviceBinding security feature Enable/disableports, MAC basedport security Portbased network accesscontrol (802.1x) VLAN(802.1q) to segregateand secure networktraffic Radiuscentralized password management SNMPv3encrypted authentication andaccess security Https/ SSH enhancenetwork security

SoftwareFeatures

STP/RSTP/MSTP(IEEE 802.1D/w/s) RedundantRing (O-Ring) withrecovery time lessthan 10ms over250 units TOS/Diffservsupported Qualityof Service (802.1p)for real-time traffic VLAN(802.1Q) with VLANtagging and GVRPsupported IGMPSnooping for multicastfiltering IP-basedbandwidth management Application-basedQoS management DOS/DDOSauto prevention Portconfiguration, status, statistics,monitoring, security DHCPServer / Clientsupport SMTPClient ModbusTCP

NetworkRedundancy

O-Ring,Open-Ring, O-chain, STP,RSTP,MSTP

RS-232in RJ45 connectorwith console cable. Baud ratesetting: 115200bps, 8,N, 1

Weight (g)

1205g

Warning/ Monitoring System

Syslogserver / clientto record andview events IncludeSMTP for eventwarning notification viaemail Eventselection support

100/1000Base-Xwith SFP port

Jumboframe

Upto 9.6K Bytes

Weight (g)

710g 740g722g 735g 735g 740g

Environmental

-40to85C(-40to185F)

StorageTemperature

-40to70C(-40to158F)

OperatingTemperature

5%to 95% Non-condensingOperatingHumidity

RegulatoryApprovals

FCCPart 15, CISPR(EN55022) class AEMI

EN61000-4-2(ESD), EN61000-4-3 (RS),EN61000-4-4 (EFT), EN61000-4-5(Surge),EN61000-4-6 (CS), EN61000-4-8,EN61000-4-11

EMS

IEC60068-2-27Shock

IEC60068-2-32

IEC60068-2-6Vibration

EN60950-1

Safety

FreeFall

Warranty

5years

1000Base- TMDI/MD I-X

Pin NumberMDI portMDI-X port

1 BI_DA+ BI_DB+

2 BI_DA- BI_DB-

3 BI_DB+ BI_DA+

4BI_DC+BI_DD+

5 BI_DC- BI_DD-

6 BI_DB- BI_DA-

7 BI_DD+ BI_DC+

8 BI_DD - B I_DC-

`LED Color Status Description

PWR Green On D Cpower on

PWR1 Green On D Cpower module1 activated

PWR2 Green On D Cpower module2 activated

R.M Green On Ring Master

On Ri ngenabled

Ring Green

Blinking

Ringstructure isbroken(i.e. partof thering is

disconnected)

Fault Amber On Faulty relay(powerfailure orport disconnected)

10/100/1000Base-T(X) Gigabit Ethernet ports

On Po rtis linked

LNK/ACT Green

Blinking Transmitted data

Duplex Amber On Port infull duplexmode

SFP

On Po rtlink up

LNK/ACT Green

Blinking Datatransmitted

IGS-9084GP-FB2

1000Base-T RJ-45 Po rt

PinNumber Assignment

1BI_DA+

2BI_DA-

3BI_DB+

4BI_DC+

5BI_DC-

6BI_DB-

7BI_DD+

8BI_DD-

ORing IndustrialNetworking Corp.

All rightsreserved.

TEL: +886-2-2218-1066 FAX:+886-2-2218-1014

Website: www.oring-networking.com E-mail: [email protected]

Bypass Port Connection

The device provides two setsof bypass fiberports, giving theSFP fiber portsaddition redundancy capabilities.Connect a LCfiber cable from afiber port toa monitor port on the front panel and another LC fiber cable from the corresponding network port to another switch.

When theswitch breaks down,incoming traffic willtravel through the bypass portboard and ontoanother active switch.

IGS-9084GP-FB2

PWR

PWR1

PWR2

10/100/1000T

G12

G11

G10

100/1000X

Network

Monitor

Note: thefiber port willstill work ifit is notconnected to anymonitor

port. However,the fiberport will nothave bypass abilitywhen the device isdown.

LCBypass Port Type

IGS-9084GP-FB2-MM

Single-Mode Multi-Mode

Reversepolarity protection

Present

10/100 Base-T(X) RJ-45 Port

Pin Number Assi gnments

1TD+

2TD-

3RD+

4 Not used

5 Not used

6RD-

7 Not used

8 Not used