ORiNG IGPMC-111GP, IGMC-111GP Quick Installation Manual

Download

Page 1

P1 P2

ETH 10/100/1000M

DPX

LNK/ACT

LFP

Fault

LNK/ACT

Speed

LFP

SW1

FailClose

FailOpen

FaultRelay

SW2

LFP

stop

PoE

IGPMC-111GP

PoE

100

100/1000X

Quick InstallationGuide

Version 1.0

Quick Installation Guide

Introduction

PRINTED ON RECYCLED PAPER

QIG

IGPMC-111GP

1907-2-29-IGPMC111GP-1.0

The is a cost-effective solution for conversion between 10/100/1000Base-T(X) and100/1000Base-X SFP interfaces,allowing you to extend communication distance by optical fiber. The device supports MDI/MDIX autodetection, so youdon’t need touse crossover wires.With a 10/100/1000Base-T(X) P.S.E. (PowerSourcing Equipment) port,the device can transmitelectrical power up to 30 watts, along with data, to remote devices over standard twisted-pair cable in an Ethernet network. It also supports LFP (Link Fault Pass-through). When one side of the link fails, the other side continues to transmit packets and will wait for a response that neverarrives from thedisconnected side. LFPcan be easilyenabled using theDIP switch. Once enabled, the link will shut down as soonas it is notified thatthe other linkhas failed, givingthe application softwarea chance to reactto the situation.The hasa wide operating

temperature range from -40~75° and a wide voltage range between 50~57 VDC, so it is suitable for harsh operating environments.

IGPMC-111GP

Package Contents

Installation

The series isshipped with thefollowing items. Ifany of theseitems is missing or damaged,please contact yourcustomer service representativefor assistance.

Preparation

Before installation, makesure you have all of the package contents available and a PC with MicrosoftInternet Explorer 6.0 or later, forusing web-based system management tools.

Elevated OperatingAmbient:

ReducedAir Flow:

If installed in a closed cabinet, theoperating ambient temperatureof the rackenvironment may begreater than roomambient. Therefore, considerationshould be givento installing theequipment in an environment compatiblewith the maximumambient temperature (Tma)specified by themanufacturer.

Installation of the equipment should be such that the amount of air flow required for safe operation of the equipment is not compromised.

Safety & Warnings

Contents

Wall-mountKit

DIN-rail Kit

IGPMC-111GP

Pictures Number

QIG

Dimension (Unit: mm)

Step 1:

Step 2:

Slant the switch and screw the Din-railkit onto theback of theswitch, right in the

middle of the back panel.

Slide theswitch onto a DIN-railfrom the Din-railkit and makesure the switchclicks into

the railfirmly.

DIN-rail Installation

Step 1:

Step 2:

Step 3:

Screw the twopieces of wall-mount kits onto bothsides of the switch. A

total of eightscrews are required, as shown below.

Use the switch,with wall mount plates attached, as a guide to mark the correct

locations of the four screws.

Insert four screwheads through the large parts ofthe keyhole-shaped apertures, and

then slide theswitch downwards. Tighten the fourscrews for added stability.

Wall-mounting

Media

Converter

Media

Converter

INDUSTRIAL

4-pin terminalblock

70.0

20.0

43.5

33.6

12.5

28.0

20.0

22.0

29.0

13.1

22.6

8.0

14.0

13.5

40.0

50.0

25.3

19.0

IGPMC-111GP

Mechanical Loading:

Circuit Overloading:

Mounting of the equipment in the d should be such that

a hazardous condition is not achieved due to uneven mechanical loading.

Consideration shouldbe given tothe connection ofthe equipment to the supplycircuit and theeffect that overloadingof the circuitsmight have onovercurrent protection andsupply wiring.Appropriate consideration ofequipment nameplate ratings should beused when addressing thisconcern.

in-rail

41.0

95.0

Panel Layouts

Front Panel

1. PowerLED

2. LNK/ACKLED for SFPport

3. PoEpower status

4. LFPstatus LED

5. FaultLED

6. DuplexLED for Gigaport

7. SFPport

8. DIP-switch2

9. Gigaport LNK/ACT LED

10. Gigaport

11. Gigaport speed LED

12. DIP-switch1

13. Faultyterminal

TopPanel

1. Wall-mountscrew holes

2. Terminalblock

Real Panel

1. Din-railscrew holes

5 6

Industrial Gigabit PoE Media

Converter

P1 P2

ETH 10/100/1000M

DPX

LNK/ACT

LFP

Fault

LNK/ACT

Speed

LFP

SW1

FailClose

FailOpen

FaultRelay

SW2

LFP

stop

PoE

IGPMC-111GP

PoE

100

100/1000X

P1 P2

ETH 10/100/1000M

DPX

LNK/ACT

LFP

Fault

LNK/ACT

Speed

LFP

SW1

FailClose

FailOpen

FaultRelay

SW2

LFP

stop

PoE

IGPMC-111GP

PoE

100

100/1000X

Page 2

QIG

Quick InstallationGuide

PRINTED ON RECYCLED PAPER

Quick Installation Guide

ORing IndustrialNetworking Corp.

All rightsreserved.

TEL: +886-2-2218-1066 FAX:+886-2-2218-1014

Website: www.oring-networking.com E-mail: [email protected]

The switch supports dual redundant power supplies which are located on the 4-pin terminal block.

Insert the negative/positive wires into the V-/V+

terminals, respectively.

To keep the DC wires from pulling loose, use a small flat-blade screwdriver to tighten the wire-clamp screws on the front of the terminalblock connector.

STEP 1:

STEP 2:

Version 1.0

QIG

Configurations

After installingthe device and connecting cables, the greenpower LED shouldturn on. Please referto the followingtablet for LEDindication.

LED indication table

Specifications

Wiring

PWR2

V2+ V2-

PWR1

V1+ V1-

Network Connection

The device has a standard Ethernet port.According to thelink type, thedevice uses CAT3, 4, 5,5e UTP cables to connect to any other network devices (Pcs, servers, switches, routers,or hubs). Please refer to the following table for cable specifications.

Cable Typesand Specifications:

For pinassignments for differenttypes of cables,please refer tothe following tables.

DIP SwitchSetting

Media

Converter

Media

Converter

INDUSTRIAL

3-PIN

DIP-Switch 1

Description

DIP-SwitchNo. Function DIP-Switch Status

ON When po wer-1 failure, e nable relay output

1 Power-1failure detection

OFF Disable power-1failure detection

ON When po wer-2 failure, e nable relay output

2 Power-2failure detection

OFF Disable power-2failure detection

ON LFP signals when detected, enable relay output

3 LFP warningdetection

OFF Disable LFP signals detection

ORing MediaConverter

Model

IGPMC-111GP

10/100/1000 Base-T(X)Ports inRJ45 Auto MDI/MDIX

Physical Ports

Technology

Ethernet standards

IEEE 802.3ifor 10Base-T IEEE 802.3ufor 100Base-TXand 100Base-FX IEEE 802.3abfor 1000Base-T IEEE 802.3zfor 1000Base-X IEEE 802.3atPoE specification(up to 30Watts per portfor P.S.E.)

Power

Input power

Power consumption(Typ.)

Dual50~57VDCvoltagepowerinputsin4pinterminalblock

4Watts

Overload currentprotection

Reversepolarity protection

Present

Present onterminal block

Physical Characteristic

Enclosure

IP-30

Dimension(WxDxH)

41(W)x70(D)x95(H)mm(1.61x2.76x3.74inch)

Weight (g)

Jumbo Frame

9K Bytes(1G mode only)

291g

Fault contact

Relay

Relayoutputtocarrycapacityof1Aat24VDCatpinterminalblock

Regulatory Approvals

FCC Part15, CISPR(EN55022) class A

EMI

EN61000-4-2 (ESD),EN61000-4-3 (RS), EN61000-4-4(EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),EN61000-4-8, EN61000-4-11

EMS

IEC60068-2-27

Shock

IEC60068-2-6

IEC60068-2-32

Vibration

Free Fall

IGPMC-111GP

Industrial Gigabit PoE Media

Converter

Cable Type Ma x. Leng th Connector

10Base-T Cat. 3, 4, 5 100-o hm UTP 100 m (328 ft) M 12

100Base-T(X) Cat. 5 100-ohm UTP UTP 100 m ( 328 ft) M12

1000BASE-T Cat. 5/Cat. 5e 10 0-ohm UTP UTP 100 m ( 328ft) M12

10/100Base-T(X) P.S.E.R J-45Definit ion

Pin No. Assignment

#1 TD+ with PoE Power input +

#2 TD - with PoE Power inpu t +

RD+ with PoE Pow er input -

Notused

#5 Notused

#6 RD-with PoE P ower input -

Notused

#8 Notused

1000Base-TP.S.E. RJ-45Pin Definition

Pin No. Description

#1 BI_DA+ with PoE Power input +

#2 BI_DA- with PoE Pow er input +

BI_DB+with PoE Power input -

BI_DC+

#5 BI_DC-

#6 BI_DB- with PoE Power input -

BI_DD+

#8 BI_DD-

LED Color Status Description

PW1 Green On DC power module 1 activated

PW2 Green On DC power module 2 activated

PoE Gree n On Power is supplied overE thernet cable

Fault Amber On An unexpectedevent occurred

10/100/1000 Base-T(X) RJ45 Port

On Port is linked

Blinking ActingLNK/ACT Green

Off Port is disconne cted

On Port runningat 100Mbps

Amber

Off Portrunning at10Mbps

Speed

Green On

Portrunning at 1000Mbps

On Full-Duplex

Duplex Green

Off Half-D uplex

SFP Port

LNK/ACT Green On Portis linked

LFP

Status Amber On LF Pfunction failed

100/1000Base-XSFP port

3-PIN

DIP-Switch 2

Description

DIP-Swith No. Function DIP-Switch Stat us

ON 10 0Base- FX mode

1 100/1000Base-FXmode selection

OFF 1 000Base -FX mod e

ON En able LF P func tion

2LFPfunction

OFF Disable LFP function

ON LFP signalwh enit is detected, the PoE outputis stopped

3 LFP co ntrol PoE out put

OFF PoE cont inuous powe r supply

Environmental

-40to85C(-40to185F)

Storage Temperature

Operating Temperature

5% to95% Non-condensing

Operating Humidity

-40to75C(-40to167F)

MTBF

1,116,093hrs

Warranty

5years

EN60950-1

Safety