Organized Living 7315-0224 Assembly Manual
a
freedomRail Assembly Instructions
2 Drawer OBox
1
(a) Attach Top. (b) Tighten Cams same as in Step 3.(a) Attach Sides to Bottom. (b) Tighten Cams by turning clockwise until snug.
Step 3: Attach Sides
Step 1: Attach Hanging Brackets
Contents of Package
Step 2: Install Connector Bolts
Step 4: Attach Top
Attach Hanging Brackets to Sides using Euroscrews. (If using Power Drill, set torque to low setting.) Install (4) Connector Bolts into small holes on Top and Bottom.
Over
Top (Inside View)
Bottom (Inside View)
Left Side
of OBox
(Inside View)
(26)
Euroscrews
1 /" Wood Screws
(2) Drawer
Left Sides
(2) Drawer
Right Sides
(2) Drawer Pulls
(4)
Machine Screws
(For Drawer Pulls)
Top and Bottom
Right Side
Back EdgeBack Edge
Left Side
Smaller Holes for
Connector Bolts
(2) Drawer Backs (Inside View)
(2) Drawer Bottoms
(2) Drawer Fronts
Connector Bolts
Hanging
Brackets
(12)
(4)
(2)
Right Side
of OBox
(Inside View)
Top
Cam
Lock
Open
a
b
a
a
b
Assembling the 2 Drawer OBox
Proper Care for an OBox: Use Goo Gone™ or Simple Green® with a rag or putty knife to remove any excess glue or marring that was caused by shipping or assembly.
(4) Full Extension Drawer Glides
Tools Required
Power Drill
#2 Phillips
Screwdriver
#2 Phillips Driver
A
l
i
g
n
A
r
r
o
w
W
i
t
h
H
o
l
e
.
©2018 Organized Living
Bloomington, IN 47403
June 2018
7315-0224
(a) Lock Cam by turning clockwise / turn Turn until snug
(b) Attach Inner Glide to Drawer with Euroscrews. Notched End should be at back.
(c) Attach Handle with Machine Screws.
Notched
End
(a) Position Drawer on Glides and push in Drawer completely.
Repeat Steps 8, 9, 10, and 11 for the second drawer.
NOTE: To remove Drawers, push the Black Tab while pulling out the Drawer.
Screw in Connector Bolts and attach Front.
(a) Attach Sides to Back. (b) Secure with 1/" Wood Screws. (c) Slide in Bottom.
Turn OBox on its side. Attach Outer Glides with Euroscrews in holes 3
and 6. Repeat for other side.
Mount OBox onto Uprights by inserting Brackets into the innermost track of each Upright.
Two people recommended for installation.
(b) Separate Inner Glide from Outer Glide by pushing the Black Tab while pulling Glide sections apart.
(a) Pull out Inner Glide to expose Black Tab.
freedomRail Assembly Instructions
2 Drawer OBox
2
OrganizedLiving.com
1-800-669-3225
Assembling/Inserting Drawers
Installing Glides
Step 5: Separate Glides
Step 6: Attach Outer Glides to OBox
Step 10: Attach Drawer Glides and Handle Step 11: Insert Drawers
Attached to OBox
Attaches to Drawer
Outer Glide Black Tab Inner Glide
Bumper
b
c
a
a
c
b
a
Step 8: Attach Drawer Panels and Drawer Bottom
Step 9: Attach Front Panel Connectors
Step 7: Mount OBox on Uprights
OBox Front
Bumper
1
2
5
6
4
3
Loading...