Oreck XL2800H2 User Manual

SIMPLY AMAZING
USERS GUIDE
XL2800H2
HIGH SPEED UPRIGHT VACUUM
CLEANER WITH
CLEANING SYSTEM
•IMPORTANT•
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
• Accessories
BEFORE OPERATING CLEANER, READ ALL
INSTRUCTIONS IN THIS
MANUAL CAREFULLY.
Table of Contents
Table of Contents,
Important Safety Instructions . . . . . . . page 2
Maintenance, Customer Service,
Warranty, and Accessories . . . . . . . . page 3
Assembly,
To Replace Paper Filter Dust Bag . . . . page 4
Operating Instructions . . . . . . . . . . . page 5
How to Replace a Worn Belt,
To Adjust or Replace Brush . . . . . . . . page 6
Bulb Replacement, Stuffing or Blockage,
Using a Fresh Air Tab . . . . . . . . . . . . page 7
Troubleshooting Guide . . . . . . . . . . . page 8
IMPORTANT
SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE
USING THIS VACUUM CLEANER
WARNING
To reduce the risk of fire,
electric shock, or injury:
• Do not leave appliance unattended when plugged in. Unplug from outlet when not in use and before servicing.
• Do not use outdoors or on wet surfaces.
• Do not operate the unit while in the upright and locked position.
• Do not let the unit run while in any one stationary position for any period of time. Keep the unit moving while in operation.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center or call customer service at
• Do not pull or carry by cord, use cord as a handle, close door on cord, or pull cord around sharp edges or corners. Keep cord away from heated surfaces.
• Do not run appliance over cord.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that may reduce air flow.
• Keep hair, loose clothing, fingers and all parts of body away from openings and moving par
• Do not use to pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without filter bag assembly in place.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids, such as gasoline or lighter fluid, or use in ar present.
• Do not use appliance in an enclosed space where flammable, explosive or toxic vapors are given off by oil base paint, paint thinner, some mothproofing substances, or in an area where flammable dust is present.
• Do not pick up toxic material such as chlorine bleach, drain
, gasoline, etc. with this appliance.
cleaner
US: 1-800-989-3535
CANADA: 1-888-676-7325
ts.
e they may be
eas wher
SAVE THESE INSTRUCTIONS
Household Use Only
Polarized Plug Notice
This product is equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact an electrician to r
2
the purpose of the polarized plug.
. This is a safety featur
eplace the obsolete outlet. Do not defeat
e. If you ar
e unable to
Maintenance and
Customer Service
ACCESSORIES
SOLD SEPARATELY
Your ORECK vacuum cleaner is a product of precise engineering. The motor bearings are permanently lubricated and should not be oiled. If you require additional information or have problems with your ORECK appliance, you may call ORECK customer service at:
In USA 1-800-989-3535 In Canada 1-888-676-7325
Please specify the model number and serial/code number which can be found on the data plate on the back of the vacuum.
Save your sales or purchase slip. Should your ORECK appliance require warranty service in the U.S.A., present this slip to the Authorized Service Center as your proof of purchase date or, in Canada, call customer service.
Warranty
ORECK MANUFACTURING COMPANY: (ORECK gives you the following limited warranty for this product only if it was originally purchased for use, not resale, from ORECK or an ORECK Authorized Retail Dealer.)
ORECK will repair or replace, free of charge, to the original purchaser, any part which is found to be defective in material or workmanship within three (3) years of the date of purchase; 10 years on housing. This limited warranty applies to normal domestic use. Any commercial use of this product will void this limited warranty.
Drive belts, revolving brushes, bulbs, disposable bags, and other parts subject to normal wear are not covered by this limited warranty.
This limited warranty does not apply to any part subjected to accident, abuse, commercial use, alteration, misuse, damage caused by fire or act of God, the use of voltages other than indicated on the serial number plate of this product or service of this product by other than ORECK or an ORECK Factory Authorized Service Center.
ORECK does not authorize any person or representative to assume or grant any other warranty obligation with the sale of this product.
ORECK’s limited warranty is valid only if you retain proof of purchase from ORECK or an ORECK Authorized Retail Dealer for this product. If you purchase this product from any other source, your purchase is “AS IS,” which means ORECK grants you no warranty, and that you, not ORECK, assume the entire risk of the quality and performance of this product, including the entire cost of any necessary servicing or repairs of any defects.
ORECK’s liability for damages to you for any costs whatsoever arising out of this statement of limited warranty shall be limited to the amount paid for this product at the time of original purchase, and ORECK shall not be liable for any direct, indirect, consequential or incidental damages arising out of the use or inability to use this product.
Some states do not allow the exclusion or limitation of incidental or conse­quential damages, so the above limitation or exclusion may not apply to you.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD, AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD.
Some states do not allow limitations on the duration of implied warranties, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
USA: 1-800-989-3535 CANADA: 1-888-676-7325
ITEM PART NUMBER
1. Dust Bag, 8 Pack Saniseal
, ACDS,
CCPK8DW
Hypo-Allergenic
2. Belts, 3 Pack 0300604 Light Bulb 00965-0019
3.
4. Fresh Air Tabs AIRTABS
3
Assembly
o assist you in identifying
T components of your vacuum, the parts have been numbered as follows
1 Handle section, upper 2 Tube, lower 3 Power head 4 Outer bag 5 Paper filter dust bag 6 Power cord 7 Retaining spring 8 Bag tension bar
9 Zip fastener 10 On/off switch 11 Cord hook 12 Plastic loop/cable clamp 13 Connector assembly 14 Fan housing 15 Cord assembly
:
5
To Replace Filter
Dust Bag
10
12
11
6
2
7
15
14
9
1
4
13
8
3
WARNING: Unplug cord from electrical outlet before servicing.
BAG REMOVAL :
1. Unsnap bag door from base.
2. Gently pull bag from cardboard collar upwards.
3. Dust seal will close automatically
Upper Handle
Plug (Cord Assembly)
Connector Assembly
Before assembling appliance. Remove two (2) screws from connector assembly (13). Slide upper handle section (1) over matching section of the connector assembly (13), aligning screw holes. Finally, insert screws in holes and tighten firmly until handle is not loose.
Machine should be in upright position when inserting cord assembly into loop.
t plug on cord assembly
Inser into handle.
rap power cord (6)
W around cord wrap (11) and cord wrap (13) and secure to “U” shaped part on plug.
BAG INSTALLATION :
1. Slide the cardboard collar onto bag dock door until the automatic closing dust seal tab hole is locked in position.
mly push bag dock door
Fir
2. with both thumbs on indication point until it snaps.
4
Operating Instructions
To Operate
Make sure the disposable paper filter dust bag is in place. DO NOT operate the cleaner without a paper filter dust bag. Plug the power cord into an electrical outlet. Choose from the low and high speed settings by pressing the ON/LOW ON/HIGH (ll) - OFF (O) switch on handle assembly when ready to operate.
General Information
The performance of your new cleaner greatly depends upon care and maintenance. The instructions in this manual will guide you in performing basic care and maintenance. To obtain the most satisfying years of service read the instructions and keep them handy for future reference.
Operating Recommendations
This new ORECK XL High-Speed Upright is one of the finest, fastest, and strongest units in its class. You’ll love the way it cleans, gets under things, and it’s SO lightweight and easy to use.
The following are a few simple suggestions regarding its operation:
1. When inserting a new disposable paper filter dust bag— FIRST PUFF OUT and OPEN THE BAG.
2. When the disposable filter dust bag is full, REPLACE IT.
3. If at any time the machine does not pick up properly or makes an unusual noise, STOP OPERATION and service.
4. Although your upright will pick up pins, paper clips, and other small objects, it is recommended that these be removed from the floor before you vacuum. Failure to do so may result in permanent damage to the motor suction fan and its housing. WARNING: Do not use your vacuum cleaner on damp
5. or wet surfaces. This will cause damage to the vacuum cleaner and is dangerous to the user use on wet or damp sur warranty.
6. REPLACE THE BELT EVERY 6 MONTHS.
7. Change the disposable filter dust bag at least once a month—even if it is not full! The collected dust in the dust bag can cause odor
ea and can affect the efficiency of the cleaner.
ar
he vacuum cleaner over cord. The
8.
DO NOT r revolving brush could damage the cord.
Disposable Paper Filter Dust Bags
Disposable paper filter dust bags play a very important role in the efficiency of your ORECK vacuum cleaner. The purpose of the paper bag is to trap dirt, but at the same time it must be por
ous enough to allow air to pass thr bag becomes clogged, no air can pass through the cleaner and cleaning cannot take place, r power. Increase the CLEANING POWER of your cleaner by changing the bag often.
To keep your cleaner operating at maximum efficiency, change the dust bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE DUST BAG.
un t
faces is not cover
, attract moisture, act as a breeding
. Damage caused by
ed under
ough. If the paper
egardless of the cleaner’s
(l)
Be sure the disposable paper filter dust bag is installed properly.
All paper dust bags are not the same. Your ORECK disposable dust bags have been designed to be used with the ORECK cleaner and using bags other than genuine ORECK disposable bags will af and could cause damage to it.
The Belt
The belt on your vacuum cleaner controls the speed of the revolving brush and is very important for the effective operation of the cleaner. If the belt becomes stretched or cut, it will cause the revolving brush to stop completely or slow down. See instructions in the manual for replacing belt.
An extra belt is stored in the base plate of your cleaner. When buying replacement belts, use ONLY ORECK genuine belts. Belts other than ORECK belts will not operate the revolving brush correctly and may create undue stress which will cause damage to the motor and brush bearings. Using belts other than ORECK belts will void the warranty.
Lubrication
The vacuum cleaner motor bearings are factory lubricated and seated. Further lubrication is not required.
General Cleaner Care
fect the cleaning ability of your cleaner
At least once a month, check for and remove excessive lint, string or hair from revolving brush.
Wipe the outside of the cleaner with a damp cloth. Also clean the connector deflector assembly area, base of cleaner and fan housing area. If there is dust in the outer bag, vacuum it or shake it out.
A little preventative maintenance will keep your cleaner looking new and will ensure continued cleaning effectiveness.
CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor Surfaces and Polished Floor Finishes
Use floor and floor finish manufacturer’s recommended methods of cleaning. The metal strip on the base of the cleaner could be damaged if used on concrete or abrasive
faces, and, ther
sur
efore, cause damage to wood floors
, soft (vinyl, asphalt tile, etc.) floor surfaces and polished floor finishes
. The roller brush may also scuff very soft finishes. Do not operate the unit while in the upright and locked position. Do not let the unit run while in any one stationary position for any period of time. Keep the unit moving while in operation.
Celoc® Hypo-Allergenic Filter System
CELOC
The filtration medical material designed to filter the smallest of dust particles. It is important that the inside of the outer bag be cleaned. Vacuum the inside of the outer bag or hand wash, turned inside out, with warm water and air dry. For best results, the CELOC SMMS outer bag should be replaced once a year
must be r Change it more often if it is used in extremely dirty areas.
ease the cleaning power of your vacuum by changing the
Incr
SMMS outer bag of your vacuum cleaner is high
yered disposable inner dust bag
la
CEL
OC
not full.
.
The
eplaced once a month even if it is
5
How to Replace a Worn Belt
To Adjust or Replace Brush
WARNING: Unplug cord from electrical outlet before servicing.
Remove the replacement belt from the storage channel.
Remove the door by removing the hold down screw located on side of power head.
Slide the door forward by prying open with a screwdriver or coin.
Remove the belt from the brush roll pulley and the motor drive shaft.
Loop the new belt over the motor drive shaft. Place the opposite end of the belt on the top of the brush pulley and roll the
ound the pulley
belt ar
Using your thumb and finger, rotate the belt on the pulley the belt encir entire circumference of the pulley
Replace the door by sliding it into the gr at the bottom of the housing. Replace the hold down scr
, ensuring that
cles the
.
ew.
.
oove
WARNING: Unplug cord from electrical outlet before servicing.
Rotate and match bearing assemblies
: Unless
ANT
IMPOR the brush is worn as indicated above, both bearings must be in the new position. When rotating, both bearings must be in the old position. Unmatched settings will cause damage to your machine.
T
To determine if the brush is worn, place a firm straight edge across the nozzle opening. If brush bristles do not extend beyond base plate, brush should be adjusted.
Remove the base plate by removing 5 screws. Then, remove the belt and brush roll from the housing.
Rotate both bearing assem­blies at ends of brush roll to show “old” and replace in the holding channels in the housing.
NOTE: The bearing assembly setting marked “OLD” has two bars ( on the top of the assembly. The one marked “NEW” has one bar ( l ). When rotating bearings, make sure both bearing assembly settings are the same and face up when replacing the brush roll.
Reassemble the belt and the base plate and check bristle height above base plate at each end of brush.
evious adjustment
If a pr
eady been made
has alr and bristle height does not extend above base plate, a new br should be ordered.
ush assembly
l l )
6
Bulb Replacement
WARNING: Unplug cord from electrical outlet before servicing.
• Remove lamp housing by removing two (2) screws in the the top of the lamp housing.
• Pull burned out bulb from holder and replace with new bulb. Use only Oreck replacement parts.
• Replace lamp housing
eplacing two screws
by r in the top of the lamp housing.
Stuffing or Blockage
Under certain conditions it is possible to stuff or block the intake tube and the lower tube assembly. If your vacuum cleaner does not pick up properly, or makes unusual noise and the outer bag does not fluff up or balloon open, follow the following steps:
WARNING: Unplug cord from electrical outlet before servicing.
4. To reassemble, check O-ring on tube, and replace if damaged. Vacuum will not operate properly without the tube O-ring. Slide O-ring to approximately 2" from base of tube. Replace tube by first lining up slot at base of tube with inner tab inside fan housing. Then reinsert tube and push down until the tube is seated. Make sure O-ring is in place against fan housing opening. Replace and tighten collar until collar locking tabs are locked in place. See illustration E. Make sure collar is not cross threaded on housing.
5. Many times blockage occurs due to a full dust bag causing dirt to back down the air flow system. When that happens, the blockage will be at the top of the system, starting in the area where the dust bag connects to the connector assembly. See illustration F.
Fan
Housing
O-ring
D
E
F
Connector
Deflector Opening
A
B
Intake Opening
Intake Opening
Retainer
Spring
1. Check for blockage at the mouth of the intake opening. See illustration A. If there is blockage, remove it with long-nose pliers, a screwdriver or coat hanger. If you can not reach the blockage, r plate. See illustration B.
2. If the blockage is not at the base, remove lower tube. See illustration C. Unhook retainer spring, releasing bottom of bag. Twist lower collar counter clockwise to slide up. Pull tube out of base. Check for blockage. If blockage is in the tube, remove with a coat hanger.
3. If tube is not blocked, look into fan housing. See illustration D. Remove debris with long-nose pliers, a screwdriver or coat hanger.
emove base
C
NOTE: If the above actions do not correct the problem, contact an ORECK authorized service center or call the customer service center.
US: 1-800-989-3535 CANADA: 1-888-676-7325
IMPORTANT: On plush and new carpets, stuffing may occur due to excessive fuzz and loose cuttings in the carpet. Stuffing could occur for the first few cleanings until all the loose material is removed. Due to the high efficiency of the cleaner, many older carpets will cause stuffing when the cleaner is first used on them.
Using A Fresh AirTab
Your ORECK XL vacuum cleaner has a special FRESH AIR tab pocket. This light-colored pocket is located inside the vinyl bag in the area where the paper disposable bag attaches to the intake tube. Insert tablet in pocket.
7
Troubleshooting Guide
WARNING: Unplug cord from electrical outlet before servicing.
SAVE SERVICE CALLS...CHECK THESE FIRST:
Is the disposable filter dust bag full?
• Are pores of filter dust bag clogged with powder or fine dust?
• Is anything clogging the revolving brush, lower tube, intake opening, fan housing or connector assembly opening?
• Is the belt in place and turning the brush?
• Are the brush ends in the proper location? Does the brush turn freely? Are hair, string or rug fibers wound
• around the brush?
PROBLEM POSSIBLE SOURCE AREAS TO CHECK
CLEANER
WILL NOT RUN
Not plugged in properly.
Be sure cleaner is firmly plugged into wall outlet.
CLEANER
DOES NOT PICK UP
No electricity in wall outlet.
Plug not firmly in handle assembly.
Filter bag is full.
Nozzle or intake pivot clogged.
Belt is broken or stretched.
Brush is worn.
Bag tube clogged.
e
Bag por clogged with fine dust.
Impeller fan is broken.
es ar
Check electrical source–fuse or circuit breaker.
Plug firmly in handle assembly.
Replace filter bag. See “To Install Paper Filter Dust Bag.”
Clear obstruction.
Replace belt.
Replace brush if bristles do not extend beyond base plate.
Clear obstruction. Change bag.
Return to Service Center for repair.
Revolving brush is not even at both ends.
Check bearing seal. Make sure
ds “old” or
wor “new” match at each end.
ALL OTHER SERVICING SHOULD BE DONE BY AN ORECK AUTHORIZED SER
VICE CENTER.
CALL CUSTOMER SERVICE HOT LINE
US: 1-800-989-3535
CANADA: 1-888-676-7325
Whenever calling, please be sure to have your model and serial number from data plate.
ved. All wor
©2002 Or
8
eck Holdings, LLC. All rights r
registered trademarks are owned and used under the authorization of Oreck Holdings, LLC.
eser
d marks, logos, pr
oduct configurations, and
75268-05 REV D
12/02 ECN# R-6815
Loading...