Oreck XL2610HH, XL2700HH, XL2700RH, XL2600HH User Manual
ENGLISH
75267-09 REV A
SIMPLY AMAZING
FRANÇAIS
®
GUIDE D’UTILISATION PAGE 8
ESPAÑOL
GUIA DEL USUARIO PAGE 14
USER’S GUIDE
XL2600HH
XL2610HH
XL2700HH
XL2700RH
HIGH SPEED UPRIGHT VACUUM
CLEANER WITH
®
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLETÀ
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
• Accessories
ENGLISH
BEFORE OPERATING CLEANER,
IMPORTANT SAFETY
READ ALL INSTRUCTIONS IN
THIS MANUAL CAREFULLY.
When using an electrical appliance, basic
Table of Contents
Maintenance and Customer Service, Polarized Plug Notice,
Accessories, Important Safety Instructions . . . . . . . . . . . . . . . page 2
Warranty, Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . page 3
Assembly, Operating Instructions, . . . . . . . . . . . . . . . . . . . . . . page 4
Operating Instructions Continued, To Replace Filter
Dust Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5
How to Replace a W
Using an Oreck Fresh Air
To Adjust or Replace Brush . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7
orn Belt, Stuffing or Blockage . . . . . . . . . page 6
®
Tab, Bulb Replacement,
Maintenance and Customer Service
Your Oreck vacuum cleaner is a product of precise engineering. The
motor bearings are permanently lubricated and should not be oiled. If
you require additional information or have problems with your Oreck
appliance, you may call ORECK customer service at:
US: 1-800-989-3535 Canada: 1-888-676-7325
Please specify the model number and serial/code number which can be
found on the data plate on the back of the vacuum.
Save your sales or purchase slip. Should your Oreck appliance require
warranty service in the U.S.A., present this slip to the Authorized Service
Center as your proof of purchase date or, in Canada, call customer
service.
Polarized Plug Notice
This product is equipped with a polarized alternating current line plug (a
plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact an electrician to replace the obsolete outlet.
Do not defeat the purpose of the polarized plug.
Accessories
ITEM PART #
1. Dust Bag, 8 Pack, Hypo-Allergenic CCPK8DW
Dust Bag, 8 Pack, Regular CCPK8
Belts, 3 Pack
2.
3. Fresh Air Tabs AIRTABS
4. Light Bulb 00965-0019
0300604
• Do not leave appliance unattended when plugged in.
Unplug from outlet when not in use and before servicing.
• Do not use outdoors or on wet surfaces.
• Do not operate the unit while in the upright and locked
position.
• Do not let the unit run while in any one stationary position
for any period of time. Keep the unit moving while in
operation.
• Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
• Use only as described in this manual. Use only
manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not
working as it should, has been dropped, damaged, left
outdoors, or dropped into water, return it to a service
center or call customer service at:
Canada: 1-888-676-7325
• Do not pull or carry by cord, use cord as a handle, close
door on cord, or pull cord around sharp edges or corners.
Keep cord away from heated surfaces.
• Do not run appliance over cord.
• Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any
opening blocked; keep free of dust, lint, hair and anything
that may reduce air flow.
• Keep hair, loose clothing, fingers and all parts of body
away from openings and moving parts.
Do not use to pick up anything that is burning or smoking,
•
such as cigarettes, matches, or hot ashes.
• Do not use without filter bag assembly in place.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids,
such as gasoline or lighter fluid, or use in areas where
they may be present.
• Do not use appliance in an enclosed space where
flammable, explosive or toxic vapors are given off by oil
base paint, paint thinner
or in an area where flammable dust is present.
• Do not pick up toxic material such as chlorine bleach,
drain cleaner, gasoline, etc. with this appliance.
INSTRUCTIONS
precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE
USING THIS VACUUM CLEANER
WARNING
To reduce the risk of fire,
electric shock, or injury:
US: 1-800-989-3535
, some mothproofing substances,
SAVE THESE INSTRUCTIONS
Household Use Only
2
ENGLISH
Warranty
ORECK MANUFACTURING COMPANY: (ORECK gives you the
following limited warranty for this product only if it was originally
purchased for use, not resale, from ORECK or an ORECK
Authorized Retail Dealer.)
ORECK will repair or replace, free of charge, to the original
purchaser, any part which is found to be defective in material or
workmanship within thr
ten (10) years on housing. This limited warranty applies to normal
domestic use. Any commercial use of this product will void this
limited warranty.
Drive belts, revolving brushes, bulbs, disposable bags, and other
parts subject to normal wear are not covered by this limited
warranty.
This limited warranty does not apply to any part subjected to
accident, abuse, commercial use, alteration, misuse, damage
caused by fire or act of God, the use of voltages other than
indicated on the serial number plate of this product or service of
this product by other than ORECK or an ORECK Factory
Authorized Service Center.
ORECK does not authorize any person or representative to assume
or grant any other warranty obligation with the sale of this
product.
ORECK’s limited warranty is valid only if you retain proof of
purchase from ORECK or an ORECK Authorized Retail Dealer for
this product. If you purchase this product from any other source,
your purchase is “AS IS,” which means ORECK grants you no
warranty, and that you, not ORECK, assume the entire risk of the
quality and performance of this product, including the entire cost
of any necessary servicing or repairs of any defects.
ORECK’s liability for damages to you for any costs whatsoever
arising out of this statement of limited warranty shall be limited to
the amount paid for this product at the time of original purchase,
and ORECK shall not be liable for any direct, indirect, consequential or incidental damages arising out of the use or inability to
use this product.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or exclusion
may not apply to you.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT,
INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A P
DURATION TO THE WARRANTY PERIOD, AND NO
WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY
AFTER THIS PERIOD.
Some states do not allow limitations on the duration of implied
warranties, so the above limitation may not apply to you.
This war
have other rights which vary from state to state.
ranty gives you specific legal rights, and you may also
ee (3) years of the date of purchase;
ARTICULAR PURPOSE, ARE LIMITED IN
Troubleshooting Guide
WARNING: Unplug cord from
electrical outlet before servicing.
SAVE SERVICE CALLS...CHECK THESE FIRST:
Is the disposable filter dust bag full?
•
• Are pores of filter dust bag clogged with powder or fine dust?
• Is anything clogging the revolving brush, lower tube, intake
opening, fan housing or connector assembly opening?
• Is the belt in place and turning the brush?
• Are the brush ends in the proper location?
Does the brush turn freely? Are hair, string or rug fibers wound
•
around the brush?
PROBLEM POSSIBLE SOURCE AREAS TO CHECK
CLEANER
WILL NOT RUN
CLEANER
DOES NOT PICK UP
ALL OTHER SER
ORECK AUTHORIZED SER
CALL CUSTOMER SERVICE HOT LINE
US: 1-800-989-3535
CANADA: 1-888-676-7325
Whenever calling, please be sure to have your model and
serial number fr
Not plugged in
properly.
No electricity in
wall outlet.
Filter bag is full.
Nozzle or intake
pivot clogged.
Belt is broken or
stretched.
Brush is worn.
Bag tube clogged.
Bag pores are
clogged with fine
dust.
Impeller fan is
broken.
Revolving brush is
not even at both
ends.
Be sure cleaner is
firmly plugged
into wall outlet.
Check electrical
source–fuse or
circuit breaker.
Replace filter bag.
See “To Install
Paper Filter Dust
Bag.”
Clear obstruction.
Replace belt.
Replace brush if
bristles do not
extend beyond
baseplate.
Clear obstruction.
Change bag.
vice
n to Ser
Retur
Center for repair.
Check bearing
seal. Make sure
words “old” or
“new” match at
each end.
VICING SHOULD BE DONE BY AN
VICE CENTER.
om data plate.
3
ENGLISH
Assembly
To assist you in identifying
components of your vacuum,
the parts have been numbered
as follows
1
2 Tube, lower
3 Power head
4 Outer bag
5 Paper filter dust bag
6 Power cord
7 Retaining spring
8 Bag tension bar
9 Zip fastener
10 On/off switch
11 Cord hook
12 Plastic loop/cable clamp
13 Connector assembly
14 Fan housing
15 Cord assembly
1
2
3
:
Handle section, upper
Upper
Handle
Connector
Assembly
5
Before assembling appliance,
remove two screws from the
connector assembly. Remove
cardboard insert by pulling
upward.
With ON/OFF switch facing
the fr
upper handle section over
matching section of the
connector assembly. Insert
short screw into top hole and
long screw into the bottom
hole then tighten firmly until
handle is no longer loose.
Attach cord to cord clip by
essing cor
pr
below clip ensuring the cord
is fully rested in clip.
10
9
1
12
4
8
3
ont of the unit, slide
13
2
14
7
d above and
Operating Instructions
To Operate
Make sure disposable paper filter dust bag is in place. DO
11
6
15
NOT operate the cleaner without a paper filter dust bag.
Plug the power cord into an electrical outlet and press the
On(l) - OFF(O) switch on handle assembly when ready to
operate.
General Information
The performance of your new cleaner greatly depends upon
care and maintenance. The instructions in this manual will
guide you in performing basic care and maintenance. To
obtain the most satisfying years of service read the instructions
and keep them handy for future reference.
Operating Recommendations
This new ORECK XL High-Speed Upright is one of the finest,
fastest, and strongest units in its class. You’ll love the way it
cleans, gets under things, and it’s SO lightweight and easy to
use.
The following are a few simple suggestions regarding its
operation:
1. When inserting a new disposable paper filter dust bag—
FIRST PUFF OUT and OPEN THE BAG.
2. When the disposable filter dust bag is full, REPLACE IT.
3. If at any time the machine does not pick up properly or
makes an unusual noise, STOP OPERATION and service.
4. Although your upright will pick up pins, paper clips, and
other small objects, it is recommended that these be
removed from the floor before you vacuum. Failure to do
so may result in permanent damage to the motor suction
fan and its housing.
WARNING: Do not use your vacuum cleaner on damp
5.
or wet surfaces. This will cause damage to the vacuum
cleaner and is dangerous to the user. Damage caused by
use on wet or damp surfaces is not covered under
warranty.
6. REPLACE THE BELT EVERY 6 MONTHS.
7. Change the disposable filter dust bag at least once a
month—even if it is not full! The collected dust in the dust
bag can cause odor
ea and can af
ar
8.
DO NOT run the vacuum cleaner over cord. The
ving brush could damage the cord.
ol
v
e
r
Disposable Paper Filter Dust Bags
Disposable paper filter dust bags play a very important role
in the efficiency of your ORECK vacuum cleaner. The purpose
of the paper bag is to trap dirt, but at the same time it must
be porous enough to allow air to pass through. If the paper
bag becomes clogged, no air can pass thr
and cleaning cannot take place, regardless of the cleaner’s
. Increase the CLEANING POWER of your cleaner by
power
changing the bag often.
o keep your cleaner operating at maximum ef
T
change the dust bag frequently. DO NOT FILL ABOVE THE
LINE INDICATED ON THE DUST BAG.
Be sure the disposable paper filter dust bag is installed
properly.
, attract moisture, act as a breeding
fect the efficiency of the cleaner.
ough the cleaner
,
ficiency
4
ENGLISH
ENFONCEZ JUSQU’À
ENTENDRE UN BRUIT
PRESIONE HASTA
ESCUCHAR UN
CHASQUIDO DE SUJECIÓN
All paper dust bags are not the same. Your ORECK
disposable dust bags have been designed to be used with the
ORECK cleaner. Using bags other than genuine ORECK
disposable bags will affect the cleaning ability of your
cleaner and could cause damage to it.
The Belt
The belt on your vacuum cleaner controls the speed of the
revolving brush and is very important for the effective
operation of the cleaner. If the belt becomes stretched or cut,
it will cause the revolving brush to stop completely or slow
down. See instructions in the manual for replacing belt.
An extra belt is stored in the baseplate of your cleaner. When
buying replacement belts, use ONLY ORECK genuine belts.
Belts other than ORECK belts will not operate the revolving
ush correctly and may create undue stress which will cause
br
damage to the motor and brush bearings. Using belts other
than ORECK belts will void the warranty.
Lubrication
The vacuum cleaner motor bearings are factory lubricated
and seated. Further lubrication is not required.
To Replace Filter
Dust Bag
WARNING: Unplug cord from
electrical outlet before servicing.
BAG REMOVAL:
1. Pull bag cardboard collar to
release bag dock door from
connector. Bag dock door
will hinge downward.
General Cleaner Care
At least once a month, check for and remove excessive
lint, string or hair from revolving brush.
Wipe the outside of the cleaner with a damp cloth. Also
clean the connector deflector assembly area, base of
cleaner and fan housing area. If there is dust in the outer
bag, vacuum it or shake it out.
A little preventative maintenance will keep your cleaner
looking new and will ensure continued cleaning effectiveness.
CAUTION—Wood Floors
Use floor and floor finish manufacturer’s recommended
methods of cleaning. The metal strip on the base of the
cleaner could be damaged if used on concrete or abrasive
e, cause damage to wood floors. The
faces, and, ther
sur
efor
roller brush may also scuff very soft finishes. Do not operate
the unit while in the upright and locked position. Do not let
the unit run while in any one stationary position for any
period of time. Keep the unit moving while in operation.
XL2600HH & XL2700HH:
® Hypo-Allergenic Filter System
Celoc
The CELOC SMMS outer bag of your vacuum cleaner is high
filtration medical material designed to filter the smallest of
dust particles. It is important the inside of the outer bag be
cleaned. Vacuum the inside of the outer bag or hand wash,
. For best
ned inside out, with war
tur
m water
, and air dr
y
results, the CELOC SMMS outer bag should be replaced
once a year.
must be replaced once a month even if it is
The CELOC layered disposable inner dust bag
not full.
Change it more often if it is used in extremely dirty areas.
Increase the cleaning power of your vacuum by changing the
bag often.
2. Gently pull bag card
cardboard collar upward out
of the bag dock. Dust seal
will close automatically
BAG INSTALLATION:
1. Slide the cardboard collar
completely onto bag dock
door.
mly push bag dock door
Fir
2.
with both thumbs on
indication point until
it snaps.
5
ENGLISH
How to Replace a Worn Belt
ARNING: Unplug cord from
W
electrical outlet before servicing.
Remove the replacement
belt from the storage
channel.
Remove the door by
removing the hold down
screw located on side of
power head.
Slide the door forward
by prying open with a
screwdriver or coin.
Remove the belt from the
brush roll pulley and the
motor drive shaft.
Loop the new belt over
the motor drive shaft.
NNEEWW PPHHOOTTO
NNEEWW PPHHOOTTO
O
O
Place the opposite end of
the belt on the top of the
ush r
oll the
oll thr
ush pulley and r
br
belt around the pulley.
Rotate the br
(3) complete revolutions
to ensur
pr
the belt retainer.
e the belt is
operly seated behind
ee
Stuffing or Blockage
Under cer
tube and the lower tube assembly. If your vacuum cleaner does
not pick up properly, or makes unusual noise and the outer bag
does not fluf
A
B
E
tain conditions it is possible to stuff or block the intake
f up or balloon open, follow the following steps:
WARNING: Unplug cord from electrical
outlet before servicing.
1. Check for blockage at the
mouth of the intake
opening. See illustration A.
If there is blockage, remove
it with long-nose pliers, a
screwdriver or coat hanger.
If you can not reach the
blockage, remove
baseplate. See illustration B.
2. If the blockage is not at the
base, remove lower tube.
See illustration C. Unhook
retainer spring, releasing
bottom of bag. Twist lower
collar counterclockwise to
slide up. Pull tube out of
base. Check for blockage. If
blockage is in the tube,
remove with a coat hanger.
3. If tube is not blocked, look
into fan housing. See illustration D. Remove debris
with long-nose pliers, a
screwdriver or coat hanger.
4. To reassemble, check O-ring
on tube, and replace if
damaged. Vacuum will not
operate properly without the
tube O-ring. Slide O-ring to
approximately 2" from base
of tube. Replace tube by
first lining up slot at base of
tube with inner tab inside
fan housing. Then r
tube and push down until
the tube is seated. Make
e O-ring is in place
sur
against fan housing
opening. Replace and
tighten collar until collar
locking tabs ar
place. See illustration E.
Make sure collar is not cross
eaded on housing.
thr
e locked in
Intake Opening
Intake Opening
Retainer
Spring
O-ring
➧
➧
C
Fan
Housing
D
einsert
Replace the door by
sliding it into the gr
at the bottom of the
housing. Replace the
hold down screw.
oove
6
Loading...