75316-08 REV A
SIMPLY AMAZING
®
USER’S GUIDE
XL2605HH
XL2205RH
HIGH SPEED UPRIGHT VACUUM
CLEANER WITH
CLEANING SYSTEM
®
•IMPORT ANT•
SAVE THIS BOOKLET!
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
• Accessories
BEFORE OPERATING
CLEANER, READ ALL
INSTRUCTIONS IN THIS
MANUAL CAREFULLY.
Table of Contents
Plug Fitting Instructions,
Important Safety Instructions . . . . . . . page 2
Maintenance and Customer Service,
Warranty, Accessories . . . . . . . . . . . page 3
Assembly,
To Replace Paper Filter Dust Bag . . . . page 4
Operating Instructions . . . . . . . . . . . page 5
How to Replace a Worn Belt,
To Adjust or Replace Brush . . . . . . . . page 6
Stuffing or Blockage,
Using an Oreck Fresh Air
®
Tab . . . . . page 7
Troubleshooting Guide . . . . . . . . . . . page 8
Important
Where Necessary for Plug to be Fitted
The wires in this mains lead are coloured in accordance
with the following code:
Blue: Neutral Brown: Live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows;
The wire which is coloured Blue must be connected to the
minal which is marked with the letter N or colour
ter
Black.
The wire which is coloured Brown
must be connected to the terminal
which is marked with the letter L
or coloured Red.
Neither wire is to be connected
to the earth pin of the 3 pin plug.
Replace fuse with same size
fuse.
ed
IMPORTANT
SAFETY INSTRUCTIONS
When using an electrical appliance, basic
precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE
USING THIS VACUUM CLEANER
WARNING
To reduce the risk of fire,
electric shock, or injury:
• Do not leave appliance unattended when plugged in. Unplug
from outlet when not in use and before servicing.
• Do not use outdoors or on wet surfaces.
• Do not operate the unit while in the upright and locked position.
• Do not let the unit run while in any one stationary position for any
period of time. Keep the unit moving while in operation.
• Do not allow to be used as a toy. Close attention is necessar y
when used by or near children.
• Use only as described in this manual. Use only manufacturer’s
recommended attachments.
• Do not use with damaged cord or plug. If appliance is not
working as it should, has been dropped, damaged, left outdoors,
or dropped into water, return it to a service center or call
customer service at
• Do not pull or carry by cord, use cord as a handle, close door on
cord, or pull cord around sharp edges or corners. Keep cord
away from heated surfaces.
• Do not run appliance over cord.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not
the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any opening
blocked; keep free of dust, lint, hair and anything that may reduce
air flow.
• Keep hair, loose clothing, fingers and all par ts of body away from
openings and moving parts.
Do not use to pick up anything that is bur
•
cigarettes, matches, or hot ashes.
• Do not use without filter bag assembly in place.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids, such as
gasoline or lighter fluid, or use in ar
present.
• Do not use appliance in an enclosed space where flammable,
explosive or toxic vapors ar
thinner, some mothproofing substances, or in an area where
flammable dust is present.
• Do not pick up toxic material such as chlorine bleach, drain
•
, gasoline, etc. with this appliance.
cleaner
Use caution when vacuuming over area rug edges and fringe.
: 0845 603 0153.
ning or smoking, such as
eas where they may be
e given of
f by oil base paint, paint
SAVE THESE INSTRUCTIONS
Household Use Only
2
Maintenance and
Customer Service
ACCESSORIES
our ORECK vacuum cleaner is a product of precise
Y
engineering. The motor bearings are permanently
lubricated and should not be oiled. If you r
equire
additional information or have problems with your
ORECK appliance, or to order new bags or spare
parts, you may call ORECK customer service at:
0845 603 0153
Or write to:
Oreck UK
P.O. Box 201
Exeter
Devon
EX1 1XB
Attention: Oreck Customer Service
Please specify the model number and serial/code
number which can be found on the data plate on the
back of the vacuum.
Save your sales or purchase slip. Should your
ORECK appliance require warranty service, present
this slip to the Authorized Service Center as your
proof of purchase date.
ITEM
1. Dust Bag, 8 Pack, Saniseal
Hypo-Aller
Dust Bag, 8 Pack, Regular
2. Belts, 3 Pack 0300604
3. Oreck Fresh Air
genic CCPK8DW
®
Tabs AIRTABS
®
PART NUMBER
CCPK8
Warranty
ORECK MANUFACTURING COMPANY: (Oreck 21180 Johnson Road;
Long Beach, MS, USA 39560 gives you the following warranty for this
product only if it was originally purchased for residential use, not resale
from Oreck or an Oreck Authorized Retail Dealer.)
Oreck will repair or replace, free of charge, to the original purchaser, any
part that is found to be defective in material or workmanship within
three (3) years of date of purchase; ten (10) years on housing. This
warranty applies to normal domestic use. Any commercial use of this
product will void this warranty. This limited warranty covers the revolving
roller brush for one (1) year for residential use only.
This warranty does not cover the replacement of expendable or
consumable parts such as carbon motor brushes, edge brushes, belts,
bulbs, disposable bags and other parts subject to normal wear unless
they are defective in material or workmanship.
This warranty does not apply to any part subjected to accident, abuse,
alteration, misuse, damage caused by act of God, the use of voltages
other than indicated on the serial number displayed on this product or
service of this product by other than Oreck or a participating Factory
Authorized Service Center.
Oreck does not authorize any person or representative to assume or
grant any other warranty obligation with the sale of this product.
Oreck’s warranty is valid only if you retain proof of purchase from Oreck
or an Oreck Authorized Retail Dealer for this product. If you purchase this
product from any other source, your purchase is “AS IS,” which means
Oreck grants you no warranty, and that you, not Oreck, assume the entire
risk of the quality and performance of this product, including the entire
cost of any necessary servicing or repairs of any defects.
This warranty is in addition to your statutory and other legal rights.
*Reconditioned units carry a 6 month warranty from date of purchase.
3
Assembly
PRESS
UNTIL SNAP
IS HEARD
ENFONCEZ JUSQU’À
ENTENDRE UN BRUIT
PRESIONE HASTA
ESCUCHAR UN
CHASQUIDO DE SUJECI ÓN
o assist you in identifying
T
components of your vacuum,
the parts have been numbered
as follows
1 Handle tube, upper
2 Tube, lower
3 Power head
4 Outer bag
5 Paper filter dust bag
6 Power cord
7 Retaining spring
8 Bag tension bar
9 Zip fastener
10 On/off switch
11 Cord hook
12 Plastic loop/cable clamp
13 Connector assembly
14 Fan housing
15 Cord assembly
:
5
To Replace Paper
Filter Dust Bag
10
9
12
4
7
8
3
11
1
13
2
14
6
15
WARNING: Unplug cord from
electrical outlet before servicing.
BAG REMOVAL:
1. Unsnap bag door from base.
2. Gently pull bag from
cardboard collar upwards.
1
Before assembling appliance,
remove two screws from
connector assembly. Remove
cardboard insert by pulling
upward.
close automatically
BAG INSTALLATION:
1. Slide the cardboard collar
completely onto bag dock
door.
3. XL2605HH: Dust seal will
2
3
With ON/OFF switch facing
the front of the unit, slide
upper handle section over
matching section of the
connector assembly. Inser t
ew into top hole and
t scr
shor
ew into bottom hole
long scr
then tighten fir
is no longer loose.
Attach cord to cord clip by
pressing cord above and below
clip ensuring the cord is fully
rested in clip.
mly until handle
mly push bag dock door
Fir
2.
with both thumbs on
indication point until
it snaps.
4
Operating Instructions
To Operate
Make sure the disposable paper filter dust bag is in place.
DO NOT operate the cleaner without a paper filter dust bag.
Plug the power cord into an electrical outlet. Press the ON
OFF
(O) switch on handle assembly when ready to operate.
General Information
The performance of your new cleaner greatly depends upon
care and maintenance. The instructions in this manual will
guide you in performing basic care and maintenance. To
obtain the most satisfying years of service read the instructions
and keep them handy for future reference.
Operating Recommendations
This new ORECK XL High-Speed Upright is one of the finest,
fastest, and strongest units in its class. You’ll love the way it
cleans, gets under things, and it’s SO lightweight and easy to
use.
The following are a few simple suggestions regarding its
operation:
1. When inser ting a new disposable paper filter dust bag—
FIRST PUFF OUT and OPEN THE BAG.
2. When the disposable filter dust bag is full, REPLACE IT.
3. If at any time the machine does not pick up properly or
makes an unusual noise, STOP OPERATION and ser vice.
4. Although your upright will pick up pins, paper clips, and
other small objects, it is recommended that these be
removed from the floor before you vacuum. Failure to do
so may result in permanent damage to the motor suction
fan and its housing.
WARNING: Do not use your vacuum cleaner on damp
5.
or wet surfaces. This will cause damage to the vacuum
cleaner and is dangerous to the user. Damage caused by
use on wet or damp surfaces is not covered under
warranty.
6. REPLACE THE BELT EVERY 6 MONTHS.
7. Change the disposable filter dust bag at least once a
month—even if it is not full! The collected dust in the dust
bag can cause odor, attract moisture, act as a breeding
ea and can af
ar
8.
DO NOT run the vacuum cleaner over cord. The
revolving brush could damage the cord.
9. Use caution when vacuuming over area rug edges and
fringe.
Disposable Paper Filter Dust Bags
Disposable paper filter dust bags play a ver
in the efficiency of your ORECK vacuum cleaner. The purpose
of the paper bag is to trap dir
be porous enough to allow air to pass through. If the paper
bag becomes clogged, no air can pass thr
and cleaning cannot take place, regardless of the cleaner’s
power.
To keep your cleaner operating at maximum efficiency,
change the dust bag frequently. DO NOT FILL ABOVE THE
LINE INDICATED ON THE DUST BAG.
Be sure the disposable paper filter dust bag is installed
properly.
fect the ef
ficiency of the cleaner
y important role
t, but at the same time it must
ough the cleaner
(l) -
.
All paper dust bags ar
disposable dust bags have been designed to be used with the
ORECK cleaner. Using bags other than genuine ORECK
TYPE CC disposable bags will affect the cleaning ability of
your cleaner and could cause damage to it.
The Belt
The belt on your vacuum cleaner controls the speed of the
revolving brush and is very important for the effective
operation of the cleaner. If the belt becomes stretched or cut,
it will cause the revolving brush to stop completely or slow
down. See instructions in the manual for replacing belt.
An extra belt is stored in the baseplate of your cleaner. When
buying replacement belts, use ONLY ORECK genuine belts.
Belts other than
brush correctly and may create undue stress which will cause
damage to the motor and brush bearings. Using belts other
than ORECK belts will void the war
Lubrication
The vacuum cleaner motor bearings are factory lubricated
and sealed. Further lubrication is not required.
General Cleaner Care
e not the same. Your ORECK
ORECK belts will not operate the revolving
ranty.
At least once a month, check
for and remove excessive lint,
string or hair from revolving
brush.
Wipe the outside of the
cleaner with a damp cloth.
Also clean the connector
deflector assembly area, base
of cleaner and fan housing
area. If there is dust in the
outer bag, vacuum it or shake
it out.
A little preventative maintenance will keep your cleaner
looking new and will ensure continued cleaning effectiveness.
CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile,
etc.) Floor Surfaces and Polished Floor Finishes
Use floor and floor finish manufactur
methods of cleaning. The metal strip on the base of the
cleaner could be damaged if used on concrete or abrasive
surfaces, and, therefore, cause damage to wood floors
ecommended
s r
er’
(vinyl, asphalt tile, etc.) floor surfaces and polished floor
finishes. The roller brush may also scuff very soft finishes. Do
not operate the unit while in the upright and locked position.
Do not let the unit run while in any one stationary position for
any period of time. Keep the unit moving while in operation.
Celoc® Hypo-Aller
The
CELOC SMMS outer bag of your vacuum cleaner is high
filtration medical material designed to filter the smallest of
dust particles. It is important the inside of the outer bag be
cleaned. Vacuum the inside of the outer bag or hand wash,
turned inside out, with warm water, and air dry. For best
results, the CELOC SMMS outer bag should be replaced
once a year
must be r
Change it mor
ease the cleaning power of your vacuum by changing the
Incr
bag often.
5
.
eplaced once a mont
genic Filter System: XL2605HH
ed disposable inner dust bag
er
y
la
OC
CEL
The
e often if it is used in extremely dirty areas.
ven if it is
h e
not full.
, soft
How to Replace a Worn Belt
To Adjust or Replace Brush
WARNING: Unplug cord from
electrical outlet before servicing.
Remove the replacement
belt from the storage
channel.
Remove the door by
removing the hold down
screw located on side of
power head.
Slide the door forward
by prying open with a
screwdriver or coin.
Remove the belt from the
brush roll pulley and the
motor drive shaft.
Loop the new belt over
the motor drive shaft.
Place the opposite end of
the belt on the brush roll
pulley.
Rotate the br
(3) complete revolutions
to ensure that no part of
the belt is over
the end of the motor
drive shaft.
Replace the door by
sliding it into the groove
at the bottom of the
housing. Replace the
hold down screw.
ush r
hanging
oll three
WARNING: Unplug cord from
electrical outlet before servicing.
Rotate and match
bearing assemblies
IMPORTANT: Unless
the brush is worn as
indicated above,
both bearings must
be in the “NEW”
position. When
rotating, both
bearings must be in
the “OLD” position.
Unmatched settings
will cause damage
to your machine.
To determine if the brush is
worn, place a firm straight
edge across the nozzle
opening. If brush bristles
do not extend beyond
baseplate, brush should be
adjusted.
Remove the baseplate by
removing 5 screws. Then,
remove the belt and brush
roll from the housing.
Rotate both bearing
assemblies at ends of
brush roll to show “OLD”
and replace in the holding
channels in the housing.
NOTE: The bearing
assembly setting marked
“OLD” has a smooth side.
The one marked “NEW”
has notches. When
rotating bearings, make
sure both bearing
assembly settings are the
same and face up when
replacing the brush roll.
Reassemble the belt and
the baseplate and check
bristle height above
baseplate at each end of
brush.
evious adjustment
If a pr
eady been made
has alr
and bristle height does not
extend above baseplate, a
ush assembly
new br
ed.
should be or
der
6
Stuffing or Blockage
Under cer
tube and the lower tube assembly. If your vacuum cleaner does
not pick up properly, or makes unusual noise and the outer bag
does not fluf
A
B
Retainer
Spring
E
tain conditions it is possible to stuff or block the intake
f up or balloon open, follow the following steps:
WARNING: Unplug cord from electrical
outlet before servicing.
1. Check for blockage at the
mouth of the intake
opening. See illustration A.
If there is blockage, remove
it with long-nose pliers, a
screwdriver or coat hanger.
If you can not reach the
blockage, remove
baseplate. See illustration B.
2. If the blockage is not at the
base, remove lower tube.
See illustration C. Unhook
retainer spring, releasing
bottom of bag. Twist lower
collar counterclockwise to
slide up. Pull tube out of
base. Check for blockage.
If blockage is in the tube,
remove with a coat hanger.
3. If tube is not blocked, look
into fan housing. See illustration D. Remove debris
with long-nose pliers, a
screwdriver or coat hanger.
4. To reassemble, check O-ring
on tube, and replace if
damaged. Vacuum will not
operate properly without the
tube O-ring. Slide O-ring to
approximately 2" from base
of tube. Replace tube by
first lining up slot at base of
tube with inner tab inside
fan housing. Then r
tube and push down until
the tube is seated. Make
e O-ring is in place
sur
against fan housing
opening. Replace and
tighten collar until collar
locking tabs ar
place. See illustration E.
Make sure collar is not cross
eaded on housing.
thr
einsert
e locked in
Intake Opening
Intake Opening
O-ring
➧
C
Fan
Housing
D
5. Many times blockage occurs
due to a full dust bag
causing dirt to back down
the air flow system. When
that happens, the blockage
will be at the top of the
system, starting in the area
e the dust bag connects
wher
to the connector assembly.
See illustration F.
NOTE: If the “Stuffing or Blockage” actions do not correct the
problem, contact an ORECK authorized service center or call the
customer service center at
IMPORTANT: On plush and new carpets, stuffing may occur
due to excessive fuzz and loose cuttings in the carpet.
Stuffing could occur for the first few cleanings until all the
loose material is removed. Due to the high efficiency of the
cleaner, many older carpets will cause stuffing when the
cleaner is first used on them.
: 0845 603 0153.
Using An Oreck Fresh Air Tab
F
Connector
Deflector
Opening
®
Your ORECK XL vacuum
cleaner has a special
Oreck Fresh Air®tab
pocket. This pocket is
located inside the outer
bag in the area where the
disposable paper bag
attaches to the intake
tube. Inser
t tablet in
pocket.
7
Troubleshooting Guide
ARNING: Unplug cord from
W
electrical outlet before servicing.
VE SERVICE CALLS...CHECK THESE FIRST:
SA
• Is the disposable filter dust bag full?
• Are pores of filter dust bag clogged with powder or fine dust?
• Is anything clogging the revolving brush, lower tube, intake
opening, fan housing or connector assembly opening?
• Is the belt in place and turning the brush?
• Are the brush ends in the proper location?
• Does the brush turn freely? Are hair, string or rug fibers wound
around the brush?
PROBLEM POSSIBLE SOURCE AREAS TO CHECK
CLEANER
NOT RUN
WILL
Not plugged in
operly .
pr
Be sure cleaner is
mly plugged
fir
into wall outlet.
CLEANER
DOES
NOT PICK UP
No electricity in
wall outlet.
Filter bag is full.
Nozzle or intake
pivot clogged.
Belt is broken or
stretched.
Brush is worn.
Bag tube clogged.
Bag pores are
clogged with fine
dust.
Impeller fan is
broken.
Revolving brush is
not even at both
ends.
Check electrical
source–fuse or
circuit breaker.
Replace filter bag.
See “To Replace
Paper Filter Dust
Bag.”
Clear obstruction.
Replace belt.
See “To Adjust or
Replace Brush.”
Clear obstruction.
Change bag.
Return to Service
Center for repair.
Check brush roll
end cards. Make
sure words “OLD”
or “NEW” match
at each end.
ALL OTHER SERVICING SHOULD BE DONE BY AN
ORECK AUTHORIZED SERVICE CENTER.
CALL CUSTOMER SERVICE HOT LINE
Whenever calling, please be sure to have your model and
serial number fr
2005 Oreck Holdings, LLC.
©
Holdings, LLC. Printed in
0845 603 0153
om data plate.
All rights reserved.
America.
All word marks, logos, product configurations, and registered trademarks are owned and used under the authority of Oreck
8
75316-08 REV A
08/05 ECN# R-7873
Loading...