Oreck SIMPLYAMAZING XL2200RS, XL2200RS User Manual
ENGLISH
USA: 1-800-989-3535
CANADA: 1-888-676-7325
COMMERCIAL: 1-800-242-1378
www.oreck.com
www.oreckcommercial.com
VISIT ONE OF OUR OVER
450 STORE LOCATIONS
75277-07 REV D
SIMPLY AMAZING
FRANÇAIS
®
GUIDE D’UTILISATION PAGE 8
ESPAÑOL
GUIA DEL USUARIO PAGE 14
USER’S GUIDE
XL2200RS
HIGH SPEED UPRIGHT VACUUM
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLET!
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
• Accessories
CLEANER WITH
®
ENGLISH
BEFORE OPERATING
CLEANER, READ ALL
INSTRUCTIONS IN THIS
MANUAL CAREFULLY.
Table of Contents
Maintenance and Customer Service,
Important Safety Instructions, Accessories . . . page 2
Warranty,
Troubleshooting Guide . . . . . . . . . . . . . . page 3
Assembly,
Operating Instructions . . . . . . . . . . . . . . . page 4
Operating Instructions cont.,
To Replace Filter Dust Bag . . . . . . . . . . . page 5
How to Replace a Worn Belt,
Stuffing or Blockage . . . . . . . . . . . . . . . . page 6
®
Using an Oreck Fresh Air
To Adjust or Replace Brush . . . . . . . . . . . page 7
Maintenance and
Customer Service
Your ORECK vacuum cleaner is a product of precise engineering.
The motor bearings are permanently lubricated and should not be
oiled. If you require additional information or have problems with
your ORECK appliance, you may call ORECK customer service at:
USA 1-800-989-3535
Canada 1-888-676-7325
Please specify the model number and serial/code number which
can be found on the data plate on the back of the vacuum.
Save your sales or purchase slip. Should your ORECK appliance
require warranty service in the U.S.A., present this slip to the
Authorized Service Center as your proof of purchase date or, in
Canada, call customer service.
Accessories
Sold Separately
USA: 1-800-989-3535 CANADA: 1-888-676-7325
ITEM PART #
Dust Bag, 8 Pack, Saniseal
1.
ACDS Hypo-Allergenic CCPK8DW
Dust Bag, 8 Pack, Regular CCPK8
Belts, 3 Pack
2.
3. Oreck Fresh Air®Tabs AIRTABS
Tab,
®
0300604
IMPORTANT
SAFETY INSTRUCTIONS
When using an electrical appliance, basic
precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE
USING THIS VACUUM CLEANER
WARNING
To reduce the risk of fire,
electric shock, or injury:
• Do not leave appliance unattended when plugged in. Unplug
from outlet when not in use and before servicing.
• Do not use outdoors or on wet surfaces.
• Do not operate the unit while in the upright and locked position.
• Do not let the unit run while in any one stationary position for any
period of time. Keep the unit moving while in operation.
• Do not allow to be used as a toy. Close attention is necessary
when used by or near children.
• Use only as described in this manual. Use only manufacturer’s
recommended attachments.
• Do not use with damaged cord or plug. If appliance is not
working as it should, has been dropped, damaged, left outdoors,
or dropped into water, return it to a service center or call
customer service at:
• Do not pull or carry by cord, use cord as a handle, close door on
cord, or pull cord around sharp edges or corners. Keep cord
away from heated surfaces.
• Do not run appliance over cord.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not
the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any opening
blocked; keep free of dust, lint, hair and anything that may reduce
air flow.
• Keep hair, loose clothing, fingers and all parts of body away from
openings and moving parts.
• Do not use to pick up anything that is burning or smoking, such as
cigarettes, matches, or hot ashes.
Do not use without filter bag assembly in place.
•
n off all controls before unplugging.
ur
T
•
Use extra car
•
• Do not use to pick up flammable or combustible liquids, such as
gasoline or lighter fluid, or use in areas where they may be
esent.
pr
Do not use appliance in an enclosed space where flammable,
•
explosive or toxic vapors are given off by oil base paint, paint
thinner, some mothproofing substances, or in an area where
flammable dust is present.
Do not pick up toxic material such as chlorine bleach, drain
•
cleaner, gasoline, etc. with this appliance.
Use caution when vacuuming over ar
•
US: 1-800-989-3535
CANADA: 1-888-676-7325
e when cleaning on stairs.
ug edges and fringe.
ea r
SAVE THESE INSTRUCTIONS
Household Use Only
.
2
ENGLISH
Polarized Plug Notice
This product is equipped with a polarized alternating current line plug (a
plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact an electrician to replace the obsolete outlet.
Do not defeat the purpose of the polarized plug
Warranty
ORECK MANUFACTURING COMPANY: (Oreck Manufacturing Company
gives you the following limited warranty for this product only if it was originally purchased for residential use, not resale, from Oreck or an Oreck
Authorized Retail Dealer.)
Oreck will repair or replace, free of charge, to the original purchaser, any
part which is found to be defective in material or workmanship within three
(3) years of the date of purchase; ten (10) years on housing. This limited
warranty applies to normal domestic use. Any commercial use of this
product will void this limited warranty. This limited warranty covers the
revolving roller brush for one (1) year for residential use only.
This limited warranty does not cover the replacement of expendable or
consumable parts such as carbon motor brushes, edge brushes, drive belts,
bulbs, disposable bags and other parts subject to normal wear unless they
are defective in material or workmanship.
This limited warranty does not apply to any part subjected to accident,
abuse, commercial use, alteration, misuse, damage caused by act of God,
the use of voltages other than indicated on the serial number displayed on
this product or service of this product by other than Oreck or a participating Factory Authorized Service Center.
Oreck does not authorize any person or representative to assume or grant
any other warranty obligation with the sale of this product.
Oreck’s limited warranty is valid only if you retain proof of purchase from
Oreck or an Oreck Authorized Retail Dealer for this product. If you
purchase this product from any other source, your purchase is “AS IS,”
which means Oreck grants you no warranty, and that you, not Oreck,
assume the entire risk of the quality and performance of this product,
including the entire cost of any necessary servicing or repairs of any
defects.
Oreck’s liability for damages to you for any costs whatsoever arising out
of this statement of limited war
this product at the time of original purchase, and Oreck shall not be liable
for any direct, indirect, consequential or incidental damages arising out of
the use or inability to use this pr
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to
you.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT,
INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO
THE WARRANTY PERIOD, AND NO WARRANTIES, WHETHER EXPRESS
OR IMPLIED, WILL APPL
Some states do not allow limitations on the duration of implied warranties,
so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
ranty shall be limited to the amount paid for
oduct.
Y AFTER THIS PERIOD.
Troubleshooting Guide
WARNING: Unplug cord from
lectrical outlet before servicing.
e
SAVE SERVICE CALLS...CHECK THESE FIRST:
• Is the disposable filter dust bag full?
• Are pores of filter dust bag clogged with powder or fine dust?
• Is anything clogging the revolving brush, lower tube, intake opening,
fan housing or connector assembly opening?
• Is the belt in place and turning the brush?
• Are the brush ends in the proper location?
• Does the brush turn freely? Are hair, string or rug fibers wound around
the brush?
PROBLEM POSSIBLE SOURCE AREAS TO CHECK
CLEANER
WILL NOT RUN
CLEANER
DOES NOTPICK U
ALL OTHER SERVICING SHOULD BE DONE BY AN
ORECK AUTHORIZED SERVICE CENTER.
CALL CUSTOMER SERVICE HOT LINE
US: 1-800-989-3535
CANADA: 1-888-676-7325
Whenever calling, please be sur
number from data plate.
Not plugged in
properly.
No electricity in
wall outlet.
Filter bag is full.
P
Nozzle or intake
pivot clogged.
Belt is broken or
stretched.
Brush is worn.
Bag tube clogged.
Bag pores are
clogged with fine
dust.
Impeller fan is
broken.
Revolving brush is
not even at both
ends.
Be sure cleaner is
firmly plugged
into wall outlet.
Check electrical
source–fuse or
circuit breaker.
Replace filter bag.
See “To Replace
Filter Dust Bag.”
Clear obstruction.
Replace belt.
See “To Adjust or
Replace Brush.”
Clear obstruction.
Change bag.
Return to Service
Center for repair.
Check brush roll
end cards. Make
sure words “OLD”
or “NEW” match
at each end.
e to have your model and serial
3
ENGLISH
Assembly
To assist you in identifying
components of your vacuum,
the parts have been numbered
as follows
10 On/off switch
11 Cord hook
12 Connector assembly
13 Fan housing
1
2
:
1 Handle section, upper
2 Tube, lower
3 Power head
4 Outer bag
5 Paper filter dust bag
6 Power cord
7 Retaining spring
8 Bag tension bar
9 Zip fastener
Upper
Handle
Connector
Assembly
5
Before assembling appliance,
remove two screws from the
connector assembly. Remove
cardboard insert by pulling
upward.
Slide upper handle section over
matching section of the connector
assembly. Insert short screw into
top hole and long scr
bottom hole then tighten firmly until
handle is no longer loose.
Operating Instructions
To Operate
9
1
11
4
12
2
6
7
10
13
8
3
ew into the
Make sure disposable paper filter dust bag is in place. DO NOT operate
the cleaner without a paper filter dust bag. Plug the power cord into an
electrical outlet and press the On (l) - OFF (O) switch on top of base
when ready to operate.
General Information
The performance of your new cleaner greatly depends upon care and
maintenance. The instructions in this manual will guide you in performing
basic care and maintenance. To obtain the most satisfying years of
service read the instructions and keep them handy for future reference.
Operating Recommendations
This new ORECK XL High-Speed Upright is one of the finest, fastest, and
strongest units in its class. You’ll love the way it cleans, gets under things,
and it’s SO lightweight and easy to use.
he following are a few simple suggestions regarding its operation:
T
1. When inserting a new disposable paper filter dust bag—FIRST PUFF
OUT and OPEN THE BAG.
2. When the disposable filter dust bag is full, REPLACE IT.
3. If at any time the machine does not pick up properly or makes an
unusual noise, STOP OPERATION and service.
4. Although your upright will pick up pins, paper clips, and other small
objects, it is recommended that these be removed from the floor
before you vacuum. Failure to do so may result in permanent
damage to the motor suction fan and its housing.
WARNING: Do not use your vacuum cleaner on damp or wet
5.
surfaces. This will cause damage to the vacuum cleaner and is
dangerous to the user. Damage caused by use on wet or damp
surfaces is not covered under warranty.
6. REPLACE THE BELT EVERY 6 MONTHS.
7. Change the disposable filter dust bag at least once a month—even
if it is not full! The collected dust in the dust bag can cause odor,
attract moisture, act as a breeding area and can affect the
efficiency of the cleaner.
DO NOT run the vacuum cleaner over cord. The revolving brush
8.
could damage the cord.
9. Use caution when vacuuming over area rug edges and fringe.
Disposable Paper Filter Dust Bags
Disposable paper filter dust bags play a ver
ficiency of your ORECK vacuum cleaner
ef
is to trap dir
to pass through. If the paper bag becomes clogged, no air can pass
ough the cleaner and cleaning cannot take place, r
thr
cleaner’s power.
To keep your cleaner operating at maximum efficiency, change the dust
bag fr
DUST BAG.
Be sure the disposable paper filter dust bag is installed properly.
All paper dust bags are not the same. Your ORECK
disposable dust bags have been designed to be used with
the ORECK cleaner
TYPE
your cleaner and could cause damage to it.
t, but at the same time it must be por
. DO NOT FILL ABOVE THE LINE INDICA
equently
. Using bags other than genuine ORECK
CC disposable bags will af
y important role in the
. The purpose of the paper bag
ous enough to allow air
dless of the
egar
TED ON THE
fect the cleaning ability of
4
ENGLISH
PRESS
UNTIL SNAP
IS HEARD
ENFONCEZ JUSQU’À
ENTENDRE UN BRUIT
PRESIONE HASTA
ESCUCHAR UN
CHASQUIDO DE SUJECIÓN
The Belt
The belt on your vacuum cleaner controls the speed of the revolving
brush and is very important for the effective operation of the cleaner. If
the belt becomes stretched or cut, it will cause the revolving brush to stop
completely or slow down. See instructions in the manual for replacing
belt.
An extra belt is stored in the baseplate of your cleaner. When buying
replacement belts, use ONLY ORECK genuine belts. Belts other than
ORECK belts will not operate the revolving brush correctly and may
create undue stress which will cause damage to the motor and brush
bearings. Using belts other than ORECK belts will void the warranty.
Lubrication
The vacuum cleaner motor bearings are factory lubricated and seated.
Further lubrication is not required.
General Cleaner Care
t least once a month, check for
A
and remove excessive lint, string or
hair from revolving brush.
ipe the outside of the cleaner with
W
a damp cloth. Also clean the
connector deflector assembly area,
base of cleaner and fan housing
area. If there is dust in the outer
bag, vacuum it or shake it out.
A little preventative maintenance will
keep your cleaner looking new and
will ensure continued cleaning
effectiveness.
To Replace Filter
Dust Bag
WARNING: Unplug cord from electrical outlet
before servicing
.
BAG REMOVAL:
1. Pull bag cardboard collar to release
bag dock door from connector.
2. Gently pul bag cardboard collar
upward out of the bag dock.
CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor
Surfaces and Polished Floor Finishes
Use floor and floor finish manufacturer’s recommended methods of
cleaning. The metal strip on the base of the cleaner could be damaged if
used on concrete or abrasive surfaces, and, therefore, cause damage to
wood floors, soft (vinyl, asphalt tile, etc.) floor surfaces and polished
floor finishes. The roller brush may also scuff very soft finishes. Do not
operate the unit while in the upright and locked position. Do not let the
unit run while in any one stationary position for any period of time. Keep
the unit moving while in operation.
BAG INSTALLATION:
1. Slide the cardboard collar
completely onto bag dock door.
2. Firmly push bag dock door with both
thumbs on indication point until
it snaps.
5
ENGLISH
How to Replace a Worn Belt
WARNING: Unplug cord from electrical outlet
before servicing.
Remove the replacement belt
from the storage channel.
Remove the door by removing
the hold down screw located on
side of power head.
Slide the door forward by
prying open with a screwdriver
or coin.
Remove the belt from the brush
roll pulley and the motor drive
shaft.
Loop the new belt over the
motor drive shaft. Place the
opposite end of the belt on the
brush roll pulley.
Rotate the br
complete revolutions to ensure
that no par
overhanging the end of the
motor drive shaft.
ush roll three (3)
t of the belt is
Stuffing or Blockage
Under certain conditions it is possible to stuff or block the intake tube
and the lower tube assembly. If your vacuum cleaner does not pick up
properly, or makes unusual noise and the outer bag does not fluff up or
balloon open, follow the following steps:
WARNING: Unplug cord from electrical outlet
before servicing.
1. Check for blockage at the
mouth of the intake opening.
See illustration A. If there is
blockage, remove it with
long-nose pliers, a screwdriver
or coat hanger. If you can not
reach the blockage, remove
A
B
Retainer
Spring
C
O-ring
D
Intake Opening
Intake Opening
Fan
Housing
baseplate. See illustration B.
2. If the blockage is not at the
emove lower tube. See
base, r
illustration C. Unhook r
spring, releasing bottom of
bag. Twist lower collar
counterclockwise to slide up.
Pull tube out of base. Check for
blockage. If blockage is in the
tube, remove with a coat
hanger.
3. If tube is not blocked, look into
fan housing. See illustration D.
Remove debris with long-nose
pliers, a screwdriver or coat
hanger.
4. To reassemble, check O-ring on
tube, and replace if damaged.
See illustration D. Vacuum will
not operate properly without the
tube Oring. Slide O-ring to
approximately 2" from base of
tube. Replace tube by first
lining up slot at base of tube
with inner tab inside fan
housing. Then reinsert tube and
push down until the tube is
seated. Make sure O-ring is in
place against fan housing
opening. Replace and tighten
collar until collar locking tabs
e locked in place. See
ar
illustration E. Make sure collar
oss thr
is not cr
housing.
etainer
eaded on
Replace the door by sliding it
into the groove at the bottom of
the housing. Replace the hold
down screw.
E
6
Loading...