Oreck RORB400, RORB550, RORB600, ROR700 User Manual

USA: 1-800-989-3535 CANADA: 1-888-676-7325 COMMERCIAL: 1-800-242-1378

 www.oreck.com

www.oreckcommercial.com 

VISIT ONE OF OUR OVER 450 STORE LOCATIONS

53367-01 REV F

SIMPLY AMAZING

USER’S GUIDE

ORBITER

MULTI-FLOOR MACHINE

RORB400 RORB550

RORB600 RORB700

SERIES

•IMPORTANT•

SAVE THIS BOOKLET!

Includes:

• Safety Warnings

• Warranty

• Operating Instructions

• Trouble Diagnosis

• Accessories

ENGLISH

BEFORE OPERATING CLEANER, READ ALL

INSTRUCTIONS IN THIS

MANUAL CAREFULLY.

Table of Contents

SAFETY & GENERAL INFORMATION . . . . . . 2

Important Safety Instructions . . . . . . . . . . . . . . . . 2

Grounding Information . . . . . . . . . . . . . . . . . . . . 3

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Customer Service . . . . . . . . . . . . . . . . . . . . . . . . 4

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . 4

GETTING STARTED . . . . . . . . . . . . . . . . . . . . . 4

Attaching Accessories . . . . . . . . . . . . . . . . . . . . 4

Removing Accessories . . . . . . . . . . . . . . . . . . . . 5

Turning Floor Machine On and Off . . . . . . . . . . . 5

To Guide the Floor Machine . . . . . . . . . . . . . . . . 5

CARPET & AREA RUG APPLICATIONS . . . . . 5

Dry Carpet Cleaning . . . . . . . . . . . . . . . . . . . . . 5

Bonnet Cleaning . . . . . . . . . . . . . . . . . . . . . . . . 5

LAMINATE, VINYL AND LINOLEUM FLOOR APPLICATIONS

Surface Cleaning . . . . . . . . . . . . . . . . . . . . . . . . 6

Scrubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Stripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Refinishing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SEALED HARDWOOD FLOOR APPLICATIONS

Surface Cleaning Sealed Floors . . . . . . . . . . . . . . 7

Sandscreening . . . . . . . . . . . . . . . . . . . . . . . . . . 8

WAXED HARDWOOD FLOOR APPLICA

face Cleaning and W

Sur

TILE FLOOR APPLICATIONS . . . . . . . . . . . . . . 8

Deep Cleaning Light Cleaning

STONE FLOOR APPLICATIONS . . . . . . . . . . . 9

Deep Cleaning Marble Restoration

CONCRETE & ASPHALT APPLICATIONS . . . . 10

Removing Oil & Dir

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . .

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Bonnets Pads

Brushes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Sand Scr

MAINTENANCE & TROUBLESHOOTING . . . . 11

Care of your Oreck Floor Machine . . . . . . . . . . . 11

User Maintenance

Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . 12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

eens

TIONS

. . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . 9

. . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . 7

. . . . . . . . . . . . . . . . .

axing Hard Wood Floors 8

. . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . 6

8 9

10 10

Safety &

General Information

IMPORTANT

SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE

USING THIS MULTI-FLOOR MACHINE

WARNING

To reduce the risk of fire,

electric shock, or injury:

Use indoors only.

•

• Risk of explosion - Floor sanding can result in an explosive mixture of fine dust and air. Use floor sanding machine only in well ventilated area.

• Do not allow to be used as a toy. Close attention is necessary when used by or near children.

• Do not leave appliance unattended when plugged in. Unplug from outlet when not in use and before servicing.

• Use only as described in this manual. Use only manufacturer’s recommended attachments.

• Do not use with a damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center or call customer service at: US: 1-800-989-3535 Canada: 1-888-676-7325 Commercial: 1-800-242-1378

• Do not pull or carry by cord, use cord as a handle, close door on cord, or pull cord around sharp edges or corners. Keep cord away from heated surfaces.

• Do not run cleaner over cord. Do not use on stairs.

•

• Connect to a properly grounded outlet only. See

ounding instructions.

• Unplug before installing or removing pads/cleaning brushes.

• Warning - To reduce the risk of fire, use only

available floor cleaners and waxes

commer intended for machine application.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cor

• Do not handle plug or cleaner with wet hands.

• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that may reduce air flow.

• Keep hair, loose clothing, fingers and all parts of body away fr

• Turn off all controls before unplugging.

• Do not use appliance in an enclosed space where flammable, explosive or toxic vapors are given off by oil base paint, paint thinner, some mothproofing substances, or in an ar present.

cially

om openings and moving par

ea wher

e flammable dust is

ts.

ENGLISH

CAUTION

This appliance must be connected to a grounded metal, permanent wiring system; or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.

ALWAYS UNPLUG THE MACHINE BEFORE

INSTALLING OR REMOVING ACCESSORIES.

ALWAYS WEAR SHOES WHEN USING

LECTRICAL EQUIPMENT.

SAVE THESE INSTRUCTIONS

Grounding Information

s CAUTION s

This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electrical current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

s WARNING s

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug

illustrated in Sketch A (see next column). A temporary adapter that looks like the adapter illustrated in Sketch B (see next column) may be used to connect this plug to a 2-pole r available. The temporar a properly grounded outlet can be installed by a qualified electrician. The green colored rigid ear, lug, or the like extending fr per cover. Whenever the adapter is used, it must be held in place by a metal scr

NOTE: In Canada, the use of a temporar permitted by the Canadian Electrical Code.

eceptacle, if a pr

om the adapter must be connected to a

manent ground such as a properly grounded outlet box

operly grounded outlet is not

y adapter should be used only until

y adapter is not

Grounding Methods

GROUNDED

OUTLET BOX

ADAPTER

GROUNDED

OUTLET

GROUNDING

Sketch A

METAL

SCREW

Sketch B

Orbiter®Model 400, 600 & 700 is

intended for Household Use.

Orbiter

Model 550 is intended for

Commercial Use.

Warranty

Oreck Corporation (Oreck) gives you the following limited warranty for this product only if it was originally purchased for use, not resale, from Oreck or an ORECK AUTHORIZED Dealer.

Oreck will repair or replace, free of charge, to the original purchaser, any part, which is found to be defective in material or workmanship within one of purchase for all models. Machine is intended for commercial use. Any commercial use voids of the 400, 600 or 700 series voids the warranty.

Components returned prepaid to an Oreck Factory Authorized Service Center or to Oreck will be repaired or replaced free of cost at the option of Oreck and/or its service center when upon examination by either of them, such components are found to be defective.

Brushes, pads, drive blocks and other parts are subject to normal wear and are not covered by this limited warranty. This limited warranty does not apply to any par to accident, abuse, alteration, misuse, damage caused by fire or act of God, the use of voltages other than indicated on the serial number plate of this pr product by other than Oreck or an Oreck Factory Authorized Ser

Oreck does not authorize any person or representative to assume or grant any other warranty obligation in connection with the sale of this pr

vice Center.

Note: The 550 series Floor

(1) year of the date

t subjected

oduct, or service of this

oduct.

Oreck's limited warranty is valid only if you retain proof of purchase from Oreck or an Oreck authorized retail dealer of this product. If you purchase this product from any other

ce, your purchase is “AS IS”, which means that Oreck

sour grants to you no warranty and that you, not Oreck, assume the entir this product, including the entire cost of any necessary

vicing or r

ser

e risk of the quality and per

epairs of any defects.

formance of

ENGLISH

Oreck's liability for damages to you for any cost whatsoever, arising out of this statement of limited warranty shall be limited to the amount paid for this

roduct at the time of original purchase, and Oreck shall

p not be liable for any direct, indirect, consequential or incidental damages arising out of the use or inability to use this product.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

LL EXPRESS AND IMPLIED WARRANTIES FOR THIS

A PRODUCT, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD, AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD.

Some jurisdictions do not allow limitations on the duration of implied warranties so the above limitation may not apply to you.

This warranty gives you specific legal rights and you may have other rights which vary from jurisdiction to jurisdiction.

Customer Service

Your ORECK floor cleaner is a product of precise engineering. If you require additional information or have problems with your ORECK appliance, you may call ORECK customer service at:

USA: 1-800-989-3535 Canada: 1-888-676-7325 Commercial: 1-800-242-1378

Please specify the model number and serial/code number which can be found on the data plate on the side of the

Orbiter Save your sales or purchase slip. Should your ORECK

appliance require warranty service in the U.S.A., present this slip to the Authorized Service Center as your proof of purchase date or, in Canada, call customer service.

Multi-Floor Machine.

Introduction

The Orbiter® Multi-Floor Machine is the most advanced,

asiest to use machine of its kind. With proper care and

e use, your Orbiter This booklet will tell you how to care for the Orbiter

Multi-Floor Machine will last a lifetime.

Multi-Floor Machine and all about its features, accessories and their uses.

AUTION:NEVER SERVICE THE MACHINE WHILE IT IS

PLUGGED IN - ALWAYS DISCONNECT it from the electrical outlet. When leaving machine unattended, be sure to disconnect it. For more information see the

Maintenance and Troubleshooting”section.

“

Getting Started

Your Orbiter assembled and ready to operate once the proper accessories are attached. The off/on switch has international symbols (O) OFF and ( l ) ON.

Attaching Accessories

The Orbiter® Multi-Floor Machine can be used on almost any surface with the right accessories. A complete list and description of the available accessories is included on page 10 under

To attach a pad, bonnet, or sand screen:

Lay the Orbiter®Multi-Floor Machine on its back with

the handle lying on the floor.

2. Attach the pad or bonnet to the black drive pad

holder using the teeth of the black drive pad holder. If attaching a sand screen, first attach the pad to the black drive pad holder. Then place the sand screen on the floor-side of the pad.

3. Place the black drive pad holder on the beige holder

pan found on the bottom of the Machine (See Figure 1, next page).

4. Set the Orbiter®Multi-Floor Machine upright with the

pad, bonnet, or sand screen sitting on the floor.

To attach a brush:

Lay the Orbiter®Multi-Floor Machine on its back with

the handle lying on the floor.

Multi-Floor Machine comes completely

“Accessories”.

Orbiter

Multi-Floor

2. With the bristles pointed away from the unit, place

ush on the beige holder pan found on the

the br bottom of the

Orbiter

Multi-Floor Machine

(See Figure 1, next page).

3. Set the Orbiter®Multi-Floor Machine upright with the

brush sitting on the floor.

CAUTION: NEVER put the brush or black drive pad holder on the machine by placing it on the floor and moving the running machine over it, or by placing the machine over the brush or black drive pad holder and then starting the motor.

ENGLISH

igure 1. Attaching Black Drive Pad Holder or Brush

CAUTION: Oreck recommends removing brushes and pads when storing the Orbiter Accessories (especially brushes) can become deformed if stored on the machine.

Removing Accessories

Lay the Orbiter®Multi-Floor Machine on its back and pull the brush or the black drive pad holder off the beige holder pan.

CAUTION: Oreck recommends removing brushes and pads when storing the Orbiter Accessories (especially brushes) can become deformed if stored on the machine.

Turning Floor Machine On and Off

The on-off switch is located on the back side of the motor housing

(400) or on the handle (550, 600, 700). It has

been designed to be conveniently activated. On (I) Off(O) is printed on the switch. (See Figure 2.) BE CAREFUL that the switch is in the OFF (O) position before you plug the electrical cord into the outlet. Before turning the machine on, be sure there is a bonnet pad or brush in place on the machine.

400

ON/OFF

Switch

Figure 2. Orbiter®Multi-Floor Machine On/Off switch

To Guide the Floor Machine

Grasp the unique “T” handle and glide the machine across the floor in a side to side motion. The patented “T” handle featur Orbiter's per smooth and easy action with fingertip control.

CAUTION: when using your Orbiter

e completing any of the following

Befor procedures for the first time, test a small hidden area to ensure color-fastness of the material and that the accessory used is not too

essive for the sur

aggr

e gives you complete control. The

fectly balanced counter-weight system gives

IMPORTANT - Always wear shoes

Multi-Floor Machine.

550, 600, 700

ON/OFF

Switch

Multi-Floor Machine.

face.

Carpet and Area Rug

Applications

Dry Carpet Cleaning

(For deep cleaning carpet and rugs)

The Oreck Dry Carpet Cleaning System®is the easiest and most effective way to keep your carpet and rugs looking

lean and beautiful. It effectively removes dirt and grime

c that vacuums cannot. Unlike many carpet extractors, steam cleaners or steam cleaning services, it will not leave a soapy or sticky residue on your carpet that will attract dirt and cause rapid resoiling. It is safe for use in homes with children and pets.

Equipment and Material Required:

• Orbiter®Multi-Floor Machine

• Black Drive Pad Holder

• White Terrycloth Bonnet (for berber or low-pile carpets) or Black Carpet Brush (for medium- or highpile carpets)

• Oreck Premist

• Oreck Dry Carpet Cleaner

Procedure:

Spray Premist® Soil Release Pre-Spray on the carpet in

a 6 ft by 6 ft area.

2. Sprinkle Dry Carpet Cleaner over the treated area (do not over use).

3. Work the Dry Carpet Cleaner into the carpet with the Orbiter terrycloth bonnet (for berber or low-pile carpets) or black carpet brush (for medium- or high-pile carpets).

4. Repeat steps 1 through 3 until the whole carpet has been treated. The carpet can be walked on during or immediately after the treatment with no ill effects.

5. When the white terrycloth bonnet becomes soiled, turn it over. When the job is complete, clean the white terrycloth bonnet in the washing machine using cold water or hose off and allow to air dry.

6. After waiting at least 30 minutes, vacuum the treated areas with an Oreck vacuum cleaner.

See Dry Carpet Cleaner packaging for complete

uctions.

instr

Bonnet Cleaning

(For surface cleaning carpet and rugs)

This procedur (follow manufacturer’s recommendations for handmade, silk and oriental rugs or carpets).

Equipment and Material Required:

Orbiter

•

• Black Drive Pad Holder

• White Terrycloth Bonnet

• Oreck Premist

Procedure:

Lightly spray Premist®Soil Release Pre-Spray over the soiled ar

Soil Release Pre-Spray

Multi-Floor Machine and the white

e can be used on most types of carpets

Multi-Floor Machine

Soil Release Pre-Spray

ea in the carpet or high traf

fic ar

ea.

ENGLISH

2. Use the Orbiter®Multi-Floor Machine and the white

terrycloth bonnet to lift dirt from the treated area. Work terrycloth bonnet over the treated area.

urn terrycloth bonnet over when soiled and continue

3.T

to clean carpet.

4. When the job is complete, clean the white terrycloth

bonnet in the washing machine using cold water or hose off and allow to air dry.

Laminate, Vinyl and

Linoleum Floor Applications

Surface Cleaning

Timberworks®Floor Cleaner restores the natural beauty of all your hard flooring

waxed floors)

scuffs and grime from your floors to reveal their original and beautiful luster.

Equipment and Material Required:

• Orbiter®Multi-Floor Machine

• Black Drive Pad Holder

• White Terrycloth Bonnet

• Timberworks

• White Polish Pad (optional)

Procedure:

To clean hard flooring, including polyurethane-coated wood, laminate, vinyl and linoleum floors, use the Timberworks

Machine with the white terrycloth bonnet.

1. Lightly mist a 6 ft by 6 ft area with Timberworks

Floor Cleaner (a little goes a long way).

2. Clean the treated area with the Orbiter®Multi-Floor

Machine and the white terrycloth bonnet.

3. Floors should shine with a beautiful luster.

Timberworks any streaking or clouding may be the result of a build-up of other floor cleaners. If necessar procedure until floor shines.

4. If desir

ed, vin to a higher luster using the white polish pad after cleaning.

See Timberworks

Scrubbing

This procedure can be used on hard floor surfaces,

EXCEPT WOOD FLOORS. Equipment and Material Required:

• Orbiter®Multi-Floor Machine

• Black Drive Pad Holder own Strip Pad or Blue Scr

•

floor surface

• Orange Scrub Brush

Vacuum, Broom or Dust Mop

•

• Cleaning Solution

Interior Cir

•

Blue Scr

(not for use on stone, tile, or

. It safely and effectively removes the dirt,

Floor Cleaner

Floor Cleaner and the Orbiter®Multi-Floor

Floor Cleaner will not leave a residue;

, repeat

yl and laminate flooring can be polished

bottle for complete instructions.

ub Pad depending on

cle (Donut Hole) from Brown Strip Pad or

ub Pad

• Mops - 2 (1 to apply/pick up Cleaning Solution and 1 to rinse floor)

• Bucket and wringer Wet-Dry Vacuum (optional)

•

Procedure:

Vacuum or sweep floor area to be cleaned with

broom or dust mop.

2. Mix cleaning solution according to manufacturer’s

nstructions on container label.

pply cleaning solution in a 6 ft by 6 ft area.

3.A

4. Let solution stand for 5 minutes, scrub floor with

Orbiter

Multi-Floor Machine and brown strip pad or

blue scrub pad.

5. Use orange scrub brush on floors with cracks, crevices, and grout.

6. Use interior circle (donut hole) from the brown strip pad or blue scrub pad to clean in corners and around door jambs by hand.

7. Pick up dirty solution with mop or wet-dry vacuum. DO NOT ALLOW CLEANING SOLUTION TO DRY ON FLOOR.

Repeat Steps 3-6 until all floor area is cleaned.

9. Mop or use Orbiter®Multi-Floor Machine with the

white terrycloth bonnet and clean water to rinse the floor area.

Precautions:

Do not flood the floor area with cleaning solution

or allow solution to dry before pick-up.

2. Use clean mop for final rinse.

3. Change rinse water frequently.

4. Use damp cloth to wipe off any splashes on walls

or furniture.

Stripping

This procedur surfaces,

e can be used on most types of har

EXCEPT WOOD & STONE FLOORS, to remove

buffable floor wax or coatings.

Equipment and Material Required:

• Orbiter®Multi-Floor Machine Black Drive Pad Holder

•

• Brown Strip Pad

acuum, Broom or Dust Mop

•

ax Remover or Stripping Solution

•

• Interior Circle (Donut Hole) from Brown Strip Pad

• Mops - 2 (1 to apply/pick up Cleaning Solution and 1 to rinse floor)

• Bucket and Wringer

• Wet-Dry Vacuum for dirty and rinse water pick-up (optional)

ocedur

Vacuum or sweep floor area to be stripped with broom or dust mop.

2. Mix stripping solution according to manufacturer’s instructions on container label.

d floor

ENGLISH

3. Dip mop in stripping solution and apply to floor in a

6 ft by 6 ft area. Apply along baseboard edges first or where there is a wax or dirt build-up.

et solution stand for 5 minutes, scrub floor with

4.L

Orbiter

Multi-Floor Machine and the brown strip pad. Use interior circle (donut hole) from the brown strip pad to reach in corners and around door jambs.

o pick up dirty solution, use a mop or wet-dry

5.T

acuum. DO NOT ALLOW STRIPPING SOLUTION

v TO DRY ON FLOOR.

6. Repeat steps 3-5 until the entire floor is completely

stripped.

7. Rinse area TWICE with clean water and clean mop.

Pick up water with mop or wet-dry vacuum.

8. Allow floor to dry before applying new floor finish.

Precautions:

Do not flood the floor with stripping solution or allow

solution to dry before pick-up.

2. Use clean mop for final rinse.

3. Change rinse water frequently.

4. Use damp cloth to wipe off any splashes on walls

or furniture.

7. Additional coats (3 and 4) of floor finish should be

applied to achieve the level of appearance desired. Four coats of floor finish will provide extra protection

o the floor surface.

8. Allow 24 hours for floor finish to harden before

buffing.

9. Buff floor to higher shine using Orbiter®Multi-Floor

Machine and white polish pad or lamb’s wool

onnet.

recautions:

When using NEW mops to apply floor finish, make sure to rinse mop first. Foreign chemicals will affect the floor finish.

2. Completely submerging mop head into the floor

finish is a waste of product.

3. Turn mop over frequently for even distribution of

floor finish.

4. Do not allow mop to become dry; this will cause

streaking.

5. Apply floor finish in thin even coats.

6. Do NOT pour floor finish directly on the floor and

attempt to spread evenly. This will cause dark spots and delay drying time.

Refinishing

This procedure can be used on most types of hard floor surfaces,

Equipment and Material Required:

Procedure:

EXCEPT WOOD & STONE FLOORS.

• Orbiter®Multi-Floor Machine

• Black Drive Pad Holder

• White Polish Pad or Lamb’s Wool Bonnet

• Floor finish liquid

• Clean string mop, 16-20 oz. size

• Bucket and wringer

• Disposable plastic bag

Place disposable bag inside of bucket with wringer. This will protect floor finish from being contaminated and chemical residue remaining in bucket.

2. Pour quart size container of floor finish into the

disposable bag. Amount of floor finish depends on size of floor ar

ea to be covered and number of coats

to be applied.

3. ONL

Y dip the mop tip into the floor finish and wring out lightly. Avoid dripping floor finish or splashing on walls.

4. Apply floor finish in thin even coats. Apply FIRST

COAT of floor finish along baseboard edges and cover remaining floor area in an left-right direction.

HINT: Only the first coat of floor finish needs to be applied to baseboar

d edges.

5. Allow floor finish to dry for 20 minutes before

applying a second coat.

6. Apply the second coat of floor finish 1 tile width

from baseboard. Application should be in a crossing direction to the preceding coat.

Sealed Hard Wood Floor

Applications

Surface Cleaning Sealed Floors

This procedure is for polyurethane-sealed hard wood floors, not waxed hard wood floors.

Timberworks all your hard flooring

waxed floors)

scuffs and grime from your floors to reveal their original and beautiful luster.

Equipment and Material Required:

Orbiter

•

• Black Drive Pad Holder

• White Terrycloth Bonnet

• Timberworks

• White Polish Pad (optional)

Procedure:

To clean hard flooring, including polyurethane-coated wood, laminate, vinyl and linoleum floors, use the

imber

T Machine with the white terrycloth bonnet. Vinyl and laminate flooring can be polished to a higher luster using the white polish pad after cleaning.

1. Lightly mist a 6 ft by 6 ft ar

Floor Cleaner (a little goes a long way).

2. Clean the tr

Machine

Floor Cleaner restores the natural beauty of

(not for use on stone, tile, or

. It safely and effectively removes the dirt,

Multi-Floor Machine

Floor Cleaner

works

Floor Cleaner and the Orbiter® Multi-Floor

ea with T

eated ar

ea with the

and the white ter

Orbiter

ycloth bonnet.

imber

works

Multi-Floor

ENGLISH

3. Floors should shine with a beautiful luster.

Timberworks

Floor Cleaner will not leave a residue;

any streaking or clouding may be the result of a

uild-up of other floor cleaners. If necessary, repeat

b procedure until floor shines.

See Timberworks

bottle for complete instructions.

Sandscreening

(Wood Floors)

Sandscreening is ideal for refinishing the polyurethane

oating on hard wood floors. The procedure is not

c designed to totally remove the old polyurethane, but smooth out imperfections and prime the floor for a new fresh coating. However, polyurethane coatings are generally very durable and look good for a long time - try a thorough cleaning before refinishing the polyurethane coating to see if the luster can be restored.

Equipment and Material Required:

• Orbiter®Multi-Floor Machine

• Black Drive Pad Holder

• Brown Strip Pad

• Sand Screen 60 grit

• Sand Screen 80 grit

• Sand Screen 100 grit

• Broom or Dust Mop

• Vacuum Cleaner

• Tack Rags

Procedure:

Use Orbiter®Multi-Floor Machine and the brown strip pad.

2. Place #60 grit sand screen disc under brown strip

pad. Sand the floor. Remove residue by vacuuming or sweeping the floor in the same direction as the boards.

3. Place a #80 sand screen disc under the brown strip

pad. Sand the floor.

4. Sweep and vacuum the floor, then tack rag

THOROUGHLY.

5. Apply finish according to manufacturer’s

recommendations.

nish between coats with #100 grit sand screen

6. Bur

disc and tack rag.

Waxed Hard Wood Floor

Applications

Surface Cleaning and Waxing Waxed Hard Wood Floors

This procedure should be used on WAX FINISH floors only.

Equipment and Material Required:

• Orbiter®Multi-Floor Machine Black Drive Pad Holder

•

• Lamb’s Wool Bonnet

• Tan Polish Brush (Union Mix) White Polish Pad (optional)

•

• Paste Wax, 1 lb. Indian Sand Paste W

•

• Dust Mop

• Buffable Wax

Procedure:

ompletely dust mop floor.

ipe up spills with a dry cloth or paper towel. Use a

2.W

slightly damp cloth for sticky spills. Hint: Buff with white polish pad to restore luster.

3. To apply paste wax: Attach black drive pad holder to

Orbiter o white polish pad on floor and center black drive pad holder onto pad. Work Orbiter

Multi-Floor Machine. Apply a tablespoon

f paste wax on 4 sections of white polish pad. Place

Multi-Floor Machine in a forward/back motion and spread out the paste wax to a thin coat. Allow paste wax to dry for 5 minutes. Turn white polish pad over to clean side and buff. Use tan polish brush or lamb’s wool bonnet to obtain a higher luster.

Helpful Hints:

When floor looks dull, try buffing first to see if that will restore the luster before re-waxing.

2. When ar

eas of heavy use no longer respond to buffing, wax only those areas and buff all of the floor to an even luster.

3. Use clear paste wax to retain the floor’s natural color.

Use Indian Sand Paste Wax to add a little color and help blend in blemishes on old floors.

Tile Floor Applications

Deep Cleaning

Equipment and Material Required:

• Orbiter®Multi-Floor Machine

• Black Drive Pad Holder

• Orange Scrub Brush or Black Carpet Brush

• White Terrycloth Bonnet

• Grunge Attack

Procedure:

unge Attack

Gr grease from tile floors and grout, leaving sparkling results.

1. Dilute Grunge Attack®Tile Floor Cleaner into a

separate spray bottle according to the instructions on the bottle.

2. Lightly spray a 6 ft by 6 ft area with diluted Grunge

Attack

3. Clean with the Orbiter®Multi-Floor Machine and an

orange scrub brush for ceramic tile floors or

ete. Use Orbiter

concr black carpet brush for delicate or glazed ceramic or porcelain tile floors.

4. Repeat steps 1 through 3 until the whole floor has

been cleaned.

5. Go back over the cleaned floor with the Orbiter

Multi-Floor Machine and white ter r

emove all dirt lifted by the orange scrub brush. Wet floor as necessary with water or diluted Grunge Attack

See Grunge Attack instructions.

Tile Floor Cleaner

ile Floor Cleaner lifts dirt, grime and

Tile Floor Cleaner.

Multi-Floor Machine and the

ycloth bonnet to

Tile Floor Cleaner.

Tile Floor Cleaner bottle for complete

ENGLISH

Light Cleaning

Equipment and Material Required:

• Orbiter®Multi-Floor Machine White Terrycloth Bonnet

• Grunge Attack

•

ile Floor Cleaner

Procedure:

Grunge Attack®Tile Floor Cleaner lifts dirt, grime and grease from tile floors and grout, leaving sparkling results.

1. Dilute Grunge Attack®Tile Floor Cleaner according to the instructions on the bottle.

ightly spray a 6 ft by 6 ft area with Grunge Attack

2.L

Tile Floor Cleaner.

3. Clean with the Orbiter®Multi-Floor Machine and

white terrycloth bonnet. This bonnet is designed to lift and remove dirt from hard surfaces.

See Grunge Attack

Cleaner bottle for complete instruc-

tions.

Stone Floor Applications

Deep Cleaning

For cleaning all types of stone floors, including marble, granite, slate and other stone floors.

Equipment and Material Required:

• Orbiter®Multi-Floor Machine

• Tan Polish Brush (Union Mix)

• Stone Clear Bottom

• Vacuum, Broom or Dust Mop

• Mop and Bucket

Procedure:

Stone Clear Bottom®Stone Floor Cleaner is a pH neutral balanced daily cleaner designed to safely clean all stone surfaces without damaging the stone’s natural crystalline surface.

1. Clean the floor with vacuum, broom or dust mop to ensure that all grit is removed.

2. Dilute Stone Clear Bottom®Stone Floor Cleaner according to the instructions on the bottle.

o clean stone floors and gr

3. T Multi-Floor Machine and the tan polish brush (union mix).

4. To remove dirt and grime lifted by the brush, mop floors with clean water or with Stone Clear Bottom Cleaning Solution.

See Stone Clear Bottom

Stone Floor Cleaner

out, use the Orbiter

bottle for complete instr

uctions.

Marble Restoration

Michaelangelo’s Marble Restorer®polishing cream is a unique blend of microabrasives that safely restores the

tone’s natural crystalline structure to rejuvenate the shine

he marble once had. It will safely and effectively revive

t dull marble surfaces, light surface scratches, abrasions, etch marks, shower wall streaks, water marks, and glass rings.

Equipment and Material Required:

•

• Black Drive Pad Holder

• Beige Marble Pad

• White Poilsh Pad

• Stone Clear Bottom

• Lamb’s Wool Bonnet (optional)

• Michaelangelo’s Marble Restorer

• Vacuum, Dust Mop or Broom

• Mop & Bucket

• Squeegee

Procedure:

2. Spray water on the floor and then apply a dab

3. Check results by moving the slurry with a squeegee.

4. Immediately mop the floor with a mix of 2 oz of

5. Let the floor dry completely. Buff the floor with an

See Michaelangelo’s Marble Restorer instructions.

Orbiter

ulti-Floor Machine

Stone Floor Cleaner

Polishing Cream

Clean the floor with vacuum, broom or dust mop to ensure that all grit has been removed. All topical coatings need to be removed.

(2 in diameter) per 16 sq ft of surface of Michaelangelo’s Marble Restorer Using Orbiter

Multi-Floor Machine and beige

polishing cream.

marble pad, begin buffing the area. Buff for five or more passes, keeping the product in a wet slurry. Do not let the product dry on the floor, and spray additional water if necessary.

Reapply or continue to buff if necessary. Remove slurry with squeegee, wet/dry vacuum or clean mop.

Stone Clear Bottom 1 gallon of water, making sur Michaelangelo’s Marble Restorer

om the floor

Orbiter

Multi-Floor Machine and a white polish pad.

Stone Floor Cleaner and

e all of the

has been removed

bottle for complete

ENGLISH

Concrete and Asphalt

Applications

Removing Oil and Dirt

Greaselock®Absorbent Powder effectively and safely cleans concrete and asphalt without solvents. Greaselock application is a natural mineral that absorbs and captures oil and dirt so it can be safely discarded or rinsed away.

quipment and Material Required:

• Orbiter®Multi-Floor Machine

• Black Drive Pad Holder

• Greaselock

Absorbent Powder

• Brown Strip Pad

• Orange Scrub Brush

Procedure:

o clean oil, dirt, mold and mildew from smooth concrete,

T use the Greaselock pad. To clean rough or uneven concrete or asphalt, use

easelock

Absorbent Powder and the brown strip

Absorbent Powder and

the orange scrub

brush.

1. For fresh stains or spills that have not dried, use the Greaselock

Absorbent Powder as a dry powder. For dry stains, add a little water during mixing or scrubbing stage.

2. Liberally apply Greaselock®Absorbent Powder to spill

or area to clean, completely covering it. Allow five to ten minutes to absorb for fresh stains, overnight for dried stains.

3. Use the Orbiter®Multi-Floor Machine and brown strip

pad or orange scrub brush to agitate the powder on the floor. Mop or hose off floor if necessary.

See Greaselock

Absorbent Powder packaging for

complete instructions.

Accessories

Oreck offers a full line of accessories to give you the tools you need for the job!

Depending on the unit purchased, some of the accessories below may be included with your Orbiter Machine. All of these accessories ar our over 450 Oreck retail Stores or on our website,

.oreck.com

www

When choosing different pads and brushes for the

Orbiter

, ther

accessor

e is no exact science to selecting an

y for a particular floor

. Bonnets ar surface cleaning most floor types. Pads are good for scrubbing and polishing flat surfaces. Brushes work well for getting into r

ecesses in non-flat sur the bristles can get into grout lines. When you choose an accessory, remember you want one aggressive enough to do the job but gentle enough not to damage the floor. Use common sense. For example, do not use a brown strip pad (aggressive) on a wood floor (soft floor). Start with what is safe and move to a mor

e aggr

needed.

Multi-Floor

e available at one of

e good for

faces, like tile, wher

, if

essive accessor

Note: Oreck recommends removing brushes and pads when storing the Orbiter

Multi-Floor Machine. Accessories

can become deformed if stored on the machine.

General

Black Drive Pad Holder 53178-51-0327

Black plastic with teeth)

(

• Holds pads and bonnets in place

Bonnets

Bonnets are designed to surface clean most surfaces. They are washable and can be reused.

White Terrycloth Bonnet 437053

• This bonnet cleans the traffic lane and spots in the carpet without wetting the entire carpet.

• Use with Oreck Premist

Soil Release Pre-Spray and

Dry Carpet Cleaner.

• When one side of bonnet is dirty, flip it over and use the other side.

• When job is complete, clean terrycloth bonnet in washing machine using cold water or hose off and allow to air dry.

Lamb’s Wool Bonnet 437054

• Designed to provide the best possible shine on wood, tile and vinyl floors.

• Use the bonnet for everyday buffing to remove scuff marks.

• When job is complete, clean lambs wool bonnet in washing machine using cold water or hose off and allow to air dry.

To use a bonnet, see and

“Removing Accessories” on page 5

“Attaching Accessories” on page 4

Pads

Pads are designed to be porous and open-weave (except the beige pad) so that when it loosens dirt it can pick it up. The dir

t goes inside the pad (i.e. of the floor). All pads can be turned over and the other side used before cleaning or disposing. Pads may be hosed of some instances and re-used.

The pads are color coded depending on how aggressive they are (except for the beige marble pad): White is the softest, followed by blue medium aggr

being the most aggressive.

White Polish Pad 437051

(least aggressive)

• Apply paste wax.

• Clean and polish wood (coated & uncoated),linoleum,

and laminate.

• Cleans all surfaces except stone.

f in

essive, and brown

ENGLISH

Blue Scrub Pad 437057

(medium aggressive)

• Used for scrubbing. Cleans tile and concrete.

•

Brown Strip Pad 437049

(most aggressive)

• Strips linoleum, vinyl, laminate and tile floors.

• Cleans and scrubs tile and grout. Can be used on commercial vinyl.

•

• Use on smooth concrete.

• Use with Sand Screens.

• Scrubs and cleans wood decks.

eige Marble Pad 437058

(marble only)

• For restoring and cleaning marble floors.

To use a floor pad, see

Removing Accessories” on page 5.

and “

“Attaching Accessories” on page 4

Brushes

Brushes are designed to get into grooves and recesses on non-flat surfaces. Brushes lift and remove ground-in dirt and grime.

Brushes are coded depending on how aggressive they are with the black carpet brush being the least aggressive, followed by the tan polish brush (union mix) and the orange scrub brush the most aggressive.

Black Carpet Brush 237049

(least aggressive)

• Use with Oreck Dry Shampoo.

• Safe, soft action needed for carpet cleaning.

• Use on textured linoleum.

• Use for cleaning delicate or glazed ceramic or porcelain tile.

Tan Polish Brush (Union Mix) 237048

(medium aggressive)

Use to polish wood floors.

•

• Will “blend” in excess floor wax, maintain an even coat of wax and eliminate wax build-up.

• Use for getting inside cracks of a wood floor. Use to polish waxed wood floors.

•

• Use for marble, stone, and delicate tile floors

Orange Scr

(most aggressive)

Used to clean ceramic tile or concrete and many tough

• stains.

o use a br

T and “

Removing

ub Brush

ush, see

Accessories”

“Attaching

Accessories”

on page 5.

237047

on page 4

Sand Screens

Sand screens offer the very best in floor sanding. For all sand screens, place the black drive pad holder on

Orbiter place the sand screen under any floor p Floor Machine onto the pad.

60 grit SS12060 80 grit SS12080 100 grit SS12100

F Cleaning Products, Please Call or Visit Your Local Oreck Dealer.

RESIDENTIAL USA: 1-800-989-3535 Canada: 1-888-676-7325 www.oreck.com

COMMERCIAL Commercial: 1-800-242-1378 www.oreckcommercial.com

Multi-Floor Machine. Then

ad on floor and center Orbiter

or Questions or Information about Oreck’s Line of

ulti-

Maintenance &

Troubleshooting

Car

e of Y

our Oreck

Multi-Floor Machine

This is a precision machine. Dropping, unreasonable bumping or rough handling may result in damage to the balanced counter-weight system. Wrap your cord loosely around the two hooks on the handle. Remove brushes after use. The bristles may be damaged due to the weight of the machine. Store your machine in the upright position. After each use, remove wax or cleaning solutions from the unit. After sanding, blow sawdust off motor. Clean housing and bumper with damp cloth after each use. A little care will keep your Orbiter

looking like new.

User Maintenance

The Orbiter®motor bearings are factory lubricated and sealed. All other ser authorized service center. There are no user serviceable parts inside.

vicing should be perfor

med by an

+ 25 hidden pages