IMPORTANT:
Please read this manual before using the unit to ensure safe and proper use.
The unit will generate the magnetic/electric field; never place any medical
equipment; watches; credit card; magnetic record card or any magnetic
sensitive products close to the unit.
Only phones with built-in QI wireless system can recharged by this unit. For
details, please refer the user’s manual of your phone.
The design of the unit is indoor use. Never spill or spray any type of liquid on the
product.
Do not use this product near water and moisture, for example: near a bathtub,
washbowl, kitchen sink or laundry tub; in a wet basement; or near a swimming
pool.
Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
Clean only with dry cloth. Unplug this product from external USB Charging
Devices before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry
closth for cleaning.
Do NOT place any heavy object on the Charging Surface. It may damage the unit.
When replacement parts are required, be sure the service technician uses
replacement parts specified by the manufacturer or those that have the same
characteristics as the original parts. Unauthorized substitutions may result in fire
or electric shock or other hazards.
1
FCC Statement
Warning: Changes or modifications to this unit not expressly approved by the party
responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
The device must not be co-located or operating in conjunction with any other
antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions : (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
2
Package Includes:
1. Charger
2. Car Mount
3. Plastic Cover
4. USB Connection Cable
5. User’s Manual
3
Installations:
Before use, assembled the Car Mount to the Charger as follows:
1. Loosen the Knob on the Charger by turning it counterclockwise as illustrated
below:
2. Insert the Car Mount into the Charger as illustrated below:
4
3. Tighten it by turning the Knob clockwise as illustrated below:
Mounting:
Mount the Charger into your vehicle as follows:
1. Tear off the protective film on the Plastic Cover then stuck it onto the desired
place as illustrated below:
2. Remove the protection film from the bottom of the Suction Cup.
5
3. Raise the Lock on the Suction Cup as illustrated below:
4. Push the Suction Cup onto the Plastic Cover; Windshield or any smooth surface
on your vehicle.
5. Press the Lock to secure it as illustrated below:
6
Connection:
Connect the Charger to your Car USB Charger (not included) as follows:
1. Connect the Micro USB Plug from the supplied USB connection cable to the
Micro USB Port on the Charger as illustrated below:
2. Connect the full size USB Plug to the USB Port on your Car USB Charger (not
included) as illustrated below:
3. The Red Power On Indicator on the Charger will illuminate.
7
Charging:
1. Mount the unit into your vehicle then connect it to your Car USB Charger as
previously instructed.
2. Press the Release Button on the rear of Charger to release the Clip as illustrated
below:
3. Place your cell phone onto the Charging surface as illustrated below:
4. Adjust the location of cell phone by sliding the Holder up/down as illustrated
below until the color of the Red Indicator on the Charger turns to blue (or, the
charging icon appears on the cell phone’s display) to start charging.
(Note: If the location of the cell phone is incorrect, charging will NOT proceed.)
8
5. Closed the Clip to hold the cell phone as illustrated below:
Notes:
1. To charge a cell phone with this Charger, the cell phone must be compatible
with the Qi standard for wireless charging.
2. During charging, if the cell phone has a cover or case, it may disturb or prevent
the wireless charging function of the cell phone.
3. The charging transmission distance of the unit is less than 8mm, the thickness of
cell phone cover or case can NOT extend 8 mm.
4. To maximize the charging speed, using a Car USB Charger (not included)
equipped with Quick Charger 3.0 USB port.
5. To save energy, disconnect the Charger from the Car USB Charger if not using it
for an extended period of time.
GENERAL SPECIFICATION:
Wireless Charging Type: Qi version 1.2
Input: DC 5V/2A or 9V/2A
Output: 5W or 10W
Transmission Distance: Up to 8 mm
SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE
9
For customer service on this product,
Please call 1-866-321-7191
Loading...