OPW 1-3122, 1-3132 Maintenance Manual
OPW Installation and Maintenance Instructions
OPW 1-3122 and 1-3132 Series Electronic Sensor Replacement
IMPORTANT: Please read these warnings and follow the
assembly instructions completely and carefully before
starting. Failure to do so may cause product failure, or
result in environmental contamination due to liquid
leakage into the soil, creating hazardous spill conditions.
IMPORTANT: The OPW 1-3100 Spill Container is preassembled for your convenience and ease of installation.
Check to make sure the unit is intact and undamaged and
all parts have been supplied. Never substitute parts for
those supplied. Doing so may cause product failure.
WARNING-DANGER: Using electrically operated
equipment near gasoline or gasoline vapors may result in
a fire or explosion, causing personal injury and property
damage or death. Be sure that the working area is free
from such hazards, and always use proper precautions.
NOTE: At all times when product is in the storage tank
keep the riser pipe capped, so the vapors cannot escape
into the environment.
Notice: OPW products must be used in compliance with
applicable federal, state, and local laws and regulations.
Product selection should be based on physical
specifications and limitations and compatibility with the
environment and material to be handled. All illustrations
and specifications in this literature are based on the latest
production information available at the time of publication.
Prices, materials, and specification are subject to change
at any time, and models may be discontinued at any time,
in either case, without notice or obligation.
Standard Product Warranty
OPW warrants that products sold by it are free from
defects in materials and workmanship for a period of one
year from the date of manufacture by OPW (ECO products
two years from date of manufacture.) Proof of purchase
may be required. As the exclusive remedy under this
limited warranty, OPW, will at its sole discretion, repair,
replace, or issue credit for future orders for any product
that may prove defective within the one year date of
manufacture period (repairs, replacements, or credits may
be subject to prorated warranty for remainder of the
original warranty period, complete proper warranty claim
documentation required.) This warranty shall not apply to
any product that has been altered in any way, which has
been repaired by any party other than a service
representative authorized by OPW, or when failure is due
to misuse, or improper installation or maintenance. OPW
shall have no liability whatsoever for special, incidental or
consequential damages to any party, and shall have no
liability for the cost of labor, freight, excavation, clean up,
downtime, removal, reinstallation, loss of profit, or any
other cost or charges.
For any product certified to California 2001 standards,
OPW warrants that product sold by it are free from defects
in material and workmanship for a period of one year from
date of manufacture or one year from date of registration
of installation not to exceed 15 months from date of
manufacture by OPW.
THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, AND
SPECIFICALLY THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THERE ARE NO
WARRANTIES, WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF.
In some states it is prohibited to use spill container drain
valves on spill containers that are exclusively used for
vapor return risers. Install only 1-3100 Series Thread-On
spill container models equipped with a drain plug.
WARNING: If the snowplow ring is removed, for any
reason, follow the Operation and Maintenance instruction
as noted. Replace o-rings and seals and install new ones.
Never reuse damaged o-rings or seals as it may result in
an improper seal. Only qualified, competent, well-trained
technicians should perform maintenance. Common sense
and good judgment should always be exercised. The
contractor’s understanding of all related site conditions
prior to starting the project is essential. If the contractor
does not have a clear understanding of the required work
and site conditions, the contractor is advised to seek
clarification prior to starting any portion of the project.
NOTICE TO DELIVERY DRIVER: All delivery drivers
MUST inspect the inside of the container for water or
contaminants other than fuel prior to delivery. If water or
contaminates are present, then they MUST be removed
before proceeding. Dispose of towels and debris safely
and per all applicable local, state, and federal codes. After
delivery is complete, the driver MUST drain any excess
fuel that may have spilled into the container from their
delivery hose.
1-3122 & 1-3132 Series Performance
Specifications:
Torque Specification:
Ring Bolts: 3/8-16 UN, 20 ft-lbs minimum to 25 ft-lbs
maximum.
Tools Recommended
Large slotted screwdriver
DW-VAC-TEST – Vacuum Test Equipment
(or 202310 Test Adaptor)
OPW 1-3100 Series Spill Container Page 25
Figure 1
10-1/2”
Sensor
Adaptor
Adaptor
O-Ring
Sensor
Conduit
(customer
Supplied)
Seal off
(customer
Supplied)
1” Min
Clearance
1-1/2” Plug
Grommet
(supplied
with sensor)
Top View into Guard
Primary
Bucket
Secondary
Bucket
OPW 1-3100 Series Spill Container Page 26
Loading...