OPTREX DMF5002N, DMC5002N Datasheet
DMF5002N (AB) No.97-0020 OPTREX CORPORATION Page 1/15
OPTREX
Type No.
*******
February 14, 1997
First Edition
Final Revision
Quality Assurance Div.
Production Div.
Checked by
Checked by
Approved by
Production Div.
Design Engineering Div.
Prepared by
LCD Module Specification
ＤＭＦ５００２Ｎ
ＤＭＦ５００２ＮＤＭＦ５００２Ｎ
ＤＭＦ５００２Ｎ
Table of Contents
1. General Specifications.............................................................................2
2. Electrical Specifications...........................................................................3
3. Optical Specifications..............................................................................6
4. I/O Terminal.............................................................................................8
5. Test..........................................................................................................10
6. Appearance Standards............................................................................11
7. Code System of Production Lot..........................................................14
8. Type Number .........................................................................................14
9. Applying Precautions.............................................................................14
10. Handling Precautions.............................................................................15
Revision History
Rev. Date Page Comment
DMF5002N (AB) No.97-0020 OPTREX CORPORATION Page 2/15
OPTREX
1.General Specifications
Operating Temp.
：
min. 0℃ ～ max. 50℃
Storage Temp.
：
min. -20℃ ～ max. 60℃
Dot Pixels
：
128 (W) × 112 (H) dots
Dot Size
：
0.50 (W) × 0.49 (H) mm
Dot Pitch
：
0.54 (W) × 0.53 (H) mm
Viewing Area
：
77.0 (W) × 66.0 (H) mm
Outline Dimensions
：
110.0 (W) × 90.6 (H) × 12.8 (D) mm
LCD Type
：
NRD-7399
( STN / Neutral-mode / Reflective )
Viewing Angle
：
6:00
Control LSI
：
T6963C-0101 (Produced by TOSHIBA)
Data Transfer
：
8-bit parallel data transfer
Backlight
：
None
Drawings
：
Dimensional Outline UE-35450
DMF5002N (AB) No.97-0020 OPTREX CORPORATION Page 3/15
OPTREX
2.Electrical Specifications
2.1.Absolute Maximum Ratings
V
SS
=0V
Parameter Symbol Conditions Min. Max. Units
Supply Voltage
(Logic)
VCC-VSS
－
-0.3 7.0 V
Supply Voltage
VCC-VEE
－
-0.3 28.0 V
(LCD Drive) VCC-V
ADJ
－
0 27.0 V
Input Voltage VI
－
-0.3 VCC+0.3 V
2.2.DC Characteristics
Ta=25℃, V
SS
=0V
Parameter Symbol Conditions Min. Typ. Max. Units
Supply Voltage
(Logic)
VCC-VSS
－
4.5 － 5.5 V
Supply Voltage
VCC-VSS
－
21.0 － 26.0 V
(LCD Drive) VCC-V
ADJ
Shown in 3.1 V
High Level
Input Voltage
VIH VCC=5.0V±10% VCC-2.2
－
V
CC
V
Low Level
Input Voltage
VIL VCC=5.0V±10% 0 － 0.8 V
High Level
Output Voltage
VOH IOH=-0.75mA VCC-0.3
－
V
CC
V
Low Level
Output Voltage
VOL IOL=0.75mA 0 － 0.3 V
Supply Current
ICC VCC-VSS=5.0V
－
8.7 20.0 mA
I
EE
VCC-V
ADJ
=18.4V
－
3.9 10.0 mA
DMF5002N (AB) No.97-0020 OPTREX CORPORATION Page 4/15
OPTREX
2.3.AC Characteristics
V
CC
=5.0V±10%
Parameter Symbol Min. Max. Units
C/D Setup Time
t
CDS
100 － ns
C/D Hold Time
t
CDH
10 － ns
CE, RD, WR Pulse Width
t
CE
,
t
RD
,
t
WR
80 － ns
Data Setup Time
t
DS
80 － ns
Data Hold Time
t
DH
40 － ns
Access Time
t
ACC
－
150 ns
Output Hold Time
t
OH
10 50 ns
(WRITE)
(READ)
RD, WR
D0～D7
CE
C/D
D0～D7
t
DS
t
OH
t
DH
t
ACC
t
CE
,
t
RD
,
t
WR
t
CDH
t
CDS
DMF5002N (AB) No.97-0020 OPTREX CORPORATION Page 5/15
OPTREX
2.4.Power Supply ON/OFF Sequence
2.4.1.ON Sequence
2.4.2.OFF Sequence
2.4.3.Reset Sequence
Please maintain the above sequence when turning on and off the power supply of the module.
If V
EE
and/or V
ADJ
is supplied to the module while internal alternate signal for LCD driving
(M) is unstable or RESET is active, DC component will be supplied to the LCD panel. This
may cause damage to the LCD module.
RESET
VCC
VADJ
SIGNAL
T≧0
T≧0T≧0T
≧
50msT≧50ms
T>2μs
LEVEL
L Level
H Level
VCC
VADJ
VCC
VSS
Power OffPower On Reset CancellationReset
VEE
VSS
VSS
VCC
VSS
VCC
VCC
VEE
0≦t
SIGNAL
0≦t
SIGNAL
VCC
LEVEL
VADJ
VADJ
VEE
VSS
VSS
VCC
VSS
VCC
VCC
VEE
0≦t
SIGNAL
0≦t
SIGNAL
VCC
LEVEL
VADJ
VADJ
Loading...