l Up to 4.25 Gb/s Bi-directional Data Links
l Duplex LC Single Mode Transceiver
l Small Form Factor, RJ-45 size, 2×5 pin Package
l 18 Wavelength (λ): 1270 nm to 1610 nm CWDM DFB
LD Transmitter
l 28 dB Power Budget at Least
l SFF-8472 Digital Diagnostic Function
l AC/AC Coupled Signal Input / Output
l LVTTL Transmitter Disable Input
l LVTTL Signal Detect Output
l Single +3.3 V Power Supply
l RoHS Compliant
l 0 to 70oC Operation
l Wave Solderable and Aqueous Washable
l Class 1 Laser International Safety Standard IEC-60825
Compliant
APPLICATIONS
l Tri-rate 1.063/2.125/4.25 Gb/s Fibre Channel
l 1.25 Gb/s 1000 BASE-LX Gigabit Ethernet
ORDER INFORMATION
P/No. Bit Rate
TRSL-8380W-CXX0G 4 / 2 / 1 400/200/100 > 28 CWDM 2×7 LC with DMI 0 to 70 5 to 1 -27 Yes
CWDM* Wavelength (0 to 70oC)
Central
Wavelength
-C270 1264.5 1270 1277.5 -C450 1444.5 1450 1457.5
-C290 1284.5 1290 1297.5 -C470 1464.5 1470 1477.5
-C310 1304.5 1310 1317.5 -C490 1484.5 1490 1497.5
-C330 1324.5 1330 1337.5 -C510 1504.5 1510 1517.5
-C350 1344.5 1350 1357.5 -C530 1524.5 1530 1537.5
-C370 1364.5 1370 1377.5 -C550 1544.5 1550 1557.5
-C390 1384.5 1390 1397.5 -C570 1564.5 1570 1577.5
-C410 1404.5 1410 1417.5 -C590 1584.5 1590 1597.5
-C430 1424.5 1430 1437.5 -C610 1604.5 1610 1617.5
CWDM*: 18 Wavelengths from 1270 nm to 1610 nm, each step 20 nm.
(Gb/s)
Min.
(nm)
FC-PI Power
Budget
(dBm)
Typ.
(nm)
Max.
(nm)
DESCRIPTION
The TRSL-8380-CXX0G series single mode transceivers is
small form factor, low power, high performance module for
bi-directional serial optical data communications such as
4x/2x/1x Fibre Channel and 1000BASE-LX Gigabit
Ethernet. This 2×7 pin SFF transceiver comply with the 2× 5
standard package defined by the SFF MSA with the
exception of four extra pins for real-time digital diagnostics
and transmitter fault indication. Digital diagnostic functions
are available via the 2-wire serial interface defined in the
SFF-8472 MSA. This module is designed for single mode
fiber and operates at a nominal wavelength of CWDM
wavelength. There are eighteen center wavelengths
available from 1270 nm to 1610 nm, with each step 20 nm.
A guaranteed minimum optical link budget of 28 dB is
offered. The transmitter section uses a multiple quantum
well CWDM DFB laser and is a class 1 laser compliant
according to International Safety Standard IEC-60825. The
receiver section uses an integrated InGaAs detector
preamplifier (IDP) mounted in an optical header and a
limiting post-amplifier IC. A PECL logic interface
simplifies interface to external circuitry.
LASER SAFETY
This single mode transceiver is a Class 1 laser product. It
complies with IEC-60825 and FDA 21 CFR 1040.10 and
1040.11. The transceiver must be operated within the
specified temperature and voltage limits. The optical ports
of the module shall be terminated with an optical connector
or with a dust plug.
@4.25 Gb/s
Output Center Wavelength
Output Spectrum Width
OMA 1500 µW
λ
∆λ
λc –5.5 λc λc +7.5
--- 1 nm -20 dB width
nm 2
Side Mode Suppression Ratio SMSR 30 dB
Optical Rise Time tr / tf 90 ps 20% to 80% Values
Relative Intensity Noise RIN -118 dB/Hz
Electrical
Data Input Current – Low IIL -350 µA
Data Input Current – High IIH 350 µA
Differential Input Voltage VIH - VIL 300 mV
Data Input Voltage – Low VIL - VCC -2.0 -1.58 V 2
Data Input Voltage -- High VIH - VCC -1.1 -0.74 V 2
Disable Input Voltage -- Low V
Disable Input Voltage -- High V
Shut Off Time for TxDis t
0 0.5 V TX Output Enabled
TDIS,L
Vcc – 1.3
TDIS,H
1 ms
DIS
Vcc V TX Ouput Disabled
1. Output power is power coupled into a 9/125 µm single mode fiber.
2. ITU-T G.694.2 CWDM wavelength from 1270 nm to 1610 nm, each step 20 nm.
3. These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs.
Signal Detect -- Asserted Pa --- --- -18 dBm Transition: low to high
Signal Detect -- Deasserted Pd -31 --- --- dBm Transition: high to low
Signal detect -- Hysteresis 1.0 --- dB
Wavelength of Operation 1260 --- 1600 nm
Electrical
Data Output Voltage – Low VOL - VCC -2.0 -1.58 V 5
Data Output Voltage – High VOH - VCC -1.1 -0.74 V 5
Signal Detect Output Voltage -- Low
Signal Detect Output Voltage -- High
3. Measured at PRBS 27-1 at BERT 1E-12.
4. Represents sensitivity based on OMA spec, as corrected to incoming Extinction Ratio of 9 dB. For example, an OMA of 2.6 µW is
approximately equal to an average power of -27.7 dBm, average with an Extinction ratio of 9 dB.
5. These outputs are compatible with 10K, 10KH and 100K ECL and PECL outputs.
SDA Data line of two wire serial interface
VeeRx Rreceiver ground
VccRx Receiver Power – 3.3V±5%
SD Signal Detect Output
RD- Receiver Data Out Bar
RD+ Receiver Data Out
Mounting Studs. Connect to Chassis
Ground
Signal Name Description
D
B
TX_Fault Transmitter Fault Indication
SCL Clock line of two wire serial interface
10 TD-
9
8
7
6
TD+ Transmitter Data In
TX_Disable Logic low to enable TXoutput
VeeTx Transmitter ground
VccTx Transmitter Power – 3.3V±5%
Transmitter Data In Bar
Module Definition
Module Definition
MOD-DEF2
PIN A
4 SDA SCL Serial module definition protocol
Module Definition 4 specifies a serial definition protocol. For this definition, upon power up, MOD-DEF(1:2) appear as no connector
(NC) and MOD-DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol. The protocol uses the
2-wire serial CMOS E2PROM protocol of the ATMEL AT24C01A/02/04 family of components.