Optoma X355, X345, W355, W345 User Manual
User manual
DLP® Projector
English
2
TABLE OF CONTENTS
SAFETY ............................................................................................... 4
Important Safety Instruction....................................................................................................... 4
3D Safety Information ................................................................................................................ 5
Copyright ................................................................................................................................... 6
Disclaimer .................................................................................................................................. 6
Trademark Recognition ............................................................................................................. 6
FCC ........................................................................................................................................... 7
Declaration of Conformity for EU countries ............................................................................... 7
WEEE ........................................................................................................................................ 7
INTRODUCTION .................................................................................. 8
Package Overview..................................................................................................................... 8
Standard accessories ................................................................................................................ 8
Optional accessories ................................................................................................................. 8
Product Overview ...................................................................................................................... 9
Connections.............................................................................................................................. 10
Keypad ..................................................................................................................................... 12
Remote control 1 ...................................................................................................................... 13
Remote control 2 ...................................................................................................................... 14
SETUP AND INSTALLATION ............................................................. 15
Installing the projector .............................................................................................................. 15
Connecting sources to the projector ......................................................................................... 16
Adjusting the projector image ................................................................................................... 19
USING THE PROJECTOR .................................................................. 22
Powering on / off the projector.................................................................................................. 22
Selecting an input source ......................................................................................................... 23
USING THE PROJECTOR .................................................................. 24
Menu navigation and features .................................................................................................. 24
OSD Menu tree......................................................................................................................... 25
Display image settings menu.................................................................................................... 34
Display 3D menu ...................................................................................................................... 36
Display aspect ratio menu ........................................................................................................ 37
Display edge mask menu ......................................................................................................... 40
Display zoom menu .................................................................................................................. 40
Display image shift menu ......................................................................................................... 40
Display keystone menu ............................................................................................................ 40
Audio mute menu ..................................................................................................................... 41
Audio volume menu .................................................................................................................. 41
Audio audio input 2 function menu ........................................................................................... 41
English
3
Audio mic volume menu ........................................................................................................... 41
Setup projection menu.............................................................................................................. 41
Setup screen type menu........................................................................................................... 41
Setup lamp settings menu ........................................................................................................ 41
Setup lter settings menu ......................................................................................................... 42
Setup power settings menu ...................................................................................................... 42
Setup security menu ................................................................................................................. 43
Setup test pattern menu ........................................................................................................... 43
Setup remote settings menu..................................................................................................... 43
Setup projector ID menu........................................................................................................... 43
Setup options menu.................................................................................................................. 44
Setup reset menu ..................................................................................................................... 45
Network LAN menu (for Type 2) ............................................................................................... 45
Network control menu............................................................................................................... 46
Setup network control settings menu ....................................................................................... 47
Info menu.................................................................................................................................. 52
MAINTENANCE .................................................................................. 53
Replacing the lamp ................................................................................................................... 53
Installing and cleaning the dust lter ........................................................................................ 55
ADDITIONAL INFORMATION ............................................................ 56
Compatible resolutions ............................................................................................................. 56
Image size and projection distance .......................................................................................... 59
Projector dimensions and ceiling mount installation ................................................................. 61
IR remote control 1 codes ........................................................................................................ 62
IR remote control 2 codes ........................................................................................................ 64
Troubleshooting ........................................................................................................................ 66
Warning indicators .................................................................................................................... 68
Specications ........................................................................................................................... 70
Optoma global ofces ............................................................................................................... 71
English
4
SAFETY
The lightning ash with arrow head within an equilateral triangle is
intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufcient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
Please follow all warnings, precautions and maintenance as recommended in this user's guide.
Important Safety Instruction
Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from
over heating, it is recommended to install the projector in a location that does not block ventilation.
As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the
projector in an enclosure such as a book case or a cabinet that restricts air ow.
To reduce the risk of re and/or electric shock, do not expose the projector to rain or moisture. Do not
install near heat sources such as radiators, heaters, stoves or any other apparatus such as ampliers
that emits heat.
Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short
out parts that could result in re or electric shock.
Do not use under the following conditions:
In extremely hot, cold or humid environments. ±
(i) Ensure that the ambient room temperature is within 5°C ~ 40°C
(ii) Relative humidity is 10% ~ 85%
In areas susceptible to excessive dust and dirt. ±
Near any appliance generating a strong magnetic eld. ±
In direct sunlight. ±
Do not use the projector in places where ammable gases or explosives gases may be present in the
atmosphere. The lamp inside the projector becomes very hot during operation and the gases may
ignite and result in a re.
Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be
(but not limited to):
Unit has been dropped. ±
Power supply cord or plug has been damaged. ±
Liquid has been spilled on to the projector. ±
Projector has been exposed to rain or moisture. ±
Something has fallen in the projector or something is loose inside. ±
Do not place the projector on an unstable surface. The projector may fall over resulting in injury or the
projector may become damaged.
Do not block the light coming out of the projector lens when in operation. The light will heat the object
and my melt, cause burns or start a re.
Please do not open or disassemble the projector as this may cause electric shock.
Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous
voltages or other hazards. Please call Optoma before you send the unit for repair.
See projector enclosure for safety related markings.
The unit should only be repaired by appropriate service personnel.
English
5
Only use attachments/accessories specied by the manufacturer.
Do not look into straight into the projector lens during operation. The bright light may harm your eyes.
When replacing the lamp, please allow the unit to cool down. Follow instructions as described on
pages 53-54.
This projector will detect the life of the lamp itself. Please be sure to change the lamp when it shows
warning messages.
Reset the "Lamp Reset" function from the on-screen display "Setup lamp settings" menu after
replacing the lamp module.
When switching the projector off, please ensure the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the projector to cool down.
When the lamp is approaching to the end of its life time, the message "Lamp life exceeded." will show
on the screen. Please contact your local reseller or service center to change the lamp as soon as
possible.
Turn off and unplug the power plug from the AC outlet before cleaning the product.
Use a soft dry cloth with mild detergent to clean the display housing. Do not use abrasive cleaners,
waxes or solvents to clean the unit.
Disconnect the power plug from AC outlet if the product is not being used for a long period of time.
When the lamp reaches the end of its life, the projector will not turn back on until the lamp module has beenNote:
replaced. To replace the lamp, follow the procedures listed under “Replacing the Lamp” section on pages
53-54.
Do not setup the projector in places where it might be subjected to vibration or shock.
Do not touch the lens with bare hands
Remove battery/batteries from remote control before storage. If the battery/batteries are left in the
remote for long periods, they may leak.
Do not use or store the projector in places where smoke from oil or cigarettes may be present, as it
can adversely affect the quality of the projector performance.
Please follow the correct projector orientation installation as non standard installation may affect the
projector performance.
Use a power strip and or surge protector. As power outages and brown-outs can KILL devices .
3D Safety Information
Please follow all warnings and precautions as recommended before you or your child use the 3D function.
Warning
Children and teenagers may be more susceptible to health issues associated with viewing in 3D and should be
closely supervised when viewing these images.
Photosensitive Seizure Warning and Other Health Risks
Some viewers may experience an epileptic seizure or stroke when exposed to certain ashing images
or lights contained in certain Projector pictures or video games. If you suffer from, or have a family
history of epilepsy or strokes, please consult with a medical specialist before using the 3D function.
Even those without a personal or family history of epilepsy or stroke may have an undiagnosed
condition that can cause photosensitive epileptic seizures.
Pregnant women, the elderly, sufferers of serious medical conditions, those who are sleep deprived or
under the inuence of alcohol should avoid utilizing the unit's 3D functionality.
If you experience any of the following symptoms, stop viewing 3D pictures immediately and consult a
medical specialist: (1) altered vision; (2) light-headedness; (3) dizziness; (4) involuntary movements
such as eye or muscle twitching; (5) confusion; (6) nausea; (7) loss of awareness; (8) convulsions;
(9) cramps; and/ or (10) disorientation. Children and teenagers may be more likely than adults
to experience these symptoms. Parents should monitor their children and ask whether they are
experiencing these symptoms.
English
6
Watching 3D projection may also cause motion sickness, perceptual after effects, disorientation, eye
strain and decreased postural stability. It is recommended that users take frequent breaks to lessen
the potential of these effects. If your eyes show signs of fatigue or dryness or if you have any of the
above symptoms, immediately discontinue use of this device and do not resume using it for at least
thirty minutes after the symptoms have subsided.
Watching 3D projection while sitting too close to the screen for an extended period of time may
damage your eyesight. The ideal viewing distance should be at least three times the screen height. It
is recommended that the viewer's eyes are level with the screen.
Watching 3D projection while wearing 3D glasses for an extended period of time may cause a
headache or fatigue. If you experience a headache, fatigue or dizziness, stop viewing the 3D
projection and rest.
Do not use the 3D glasses for any other purpose than for watching 3D projection.
Wearing the 3D glasses for any other purpose (as general spectacles, sunglasses, protective goggles,
etc.) may be physically harmful to you and may weaken your eyesight.
Viewing in 3D projection may cause disorientation for some viewers. Accordingly, DO NOT place your
3D PROJECTOR near open stairwells, cables, balconies, or other objects that can be tripped over, run
into, knocked down, broken or fallen over.
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright
laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced
without written consent of the author.
© Copyright 2016
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations
or warranties with respect to the contents hereof and specically disclaims any implied warranties of
merchantability or tness for any particular purpose. The manufacturer reserves the right to revise this publication
and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any
person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending
applications in other countries throughout the world.
HDMI, the HDMI Logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
DLP , DLP Link and the DLP logo are registered trademarks of Texas Instruments and BrilliantColorTM is a
trademark of Texas Instruments.
All other product names used in this manual are the properties of their respective owners and are
Acknowledged.
DARBEE is a trademark by Darbee Products, Inc.
MHL, Mobile High-Denition Link and the MHL Logo are trademarks or registered trademarks of MHL Licensing,
LLC.
English
7
FCC
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause
harmful interference to radio or television reception, which can be determined by turning the device off and on is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC
regulations.
Caution
Changes or modications not expressly approved by the manufacturer could void the user's authority, which is
granted by the Federal Communications Commission, to operate this projector.
Operation Conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Remarque l'intention des utilisateurs canadiens
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.
Declaration of Conformity for EU countries
EMC Directive 2004/108/EC (including amendments)
Low Voltage Directive 2006/95/EC
R & TTE Directive 1999/5/EC (if product has RF function)
WEEE
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure
utmost protection of the global environment, please recycle it.
INTRODUCTION
Package Overview
Carefully unpack and verify that you have the items listed below under standard accessories. Some of the items
under optional accessories may not be available depending on the model, specication and your region of
purchase. Please check with your place of purchase. Some accessories may vary from region to region.
The warranty card is only supplied in some specic regions. Please consult your dealer for detailed information.
Standard accessories
CD User Manual
Warranty Card*(1)
Basic User Manual
Projector Power lead *(3)
Note:
The remote control is shipped with the battery.
*(1) For European warranty information please visit www.optomaeurope.com.
*(2) The actual remote control may vary depending on the region.
*(3) Power lead is depending on the region.
Optional accessories
Carry bag
Remote control *(2)
VGA cable
HDMI cable
Documentation
Lens cap
8
Optional accessories vary depending on model, specication and region.Note:
English
INTRODUCTION
Product Overview
13
1 32 5
9
4
6
78
10
12 11
Do not block projector inlet or outlet air vents.Note:
No Item No Item
1. Lamp Cover 8. Lens
2.
Focus Ring
Ventilation (inlet)
9.
3. Zoom Lever 10. Ventilation (outlet)
4. IR Receiver 11. Kensington
5. Keypad 12. Power Socket
6. Tilt-Adjustment Foot 13. Input / Output
7. Security Bar
TM
Lock Port
English
9
English
10
INTRODUCTION
Audio Out
Audio In
VIDEO
VGA-IN / YPbPr
RS-232C
VGA-OUT / YPbPr
HDMI
USB Power
MOUSE /
SERVICE
Out (5V 1.0A)
HDMI 1 / MHL
Audio In
Audio Out
VIDEO
VGA-IN 1 / YPbPr
RS-232C
VGA-IN 2 / YPbPr
HDMI 2
USB Power
MOUSE /
SERVICE
Out (5V 1.0A)
VGA-OUT / YPbPr
S-VIDEO
Audio In /Mic In
RJ-45
Connections
Type 1 XGA/ WXGA
Type 2 XGA/ WXGA
134b32b
1214
11
54a32a1
8
6
6
7
7
8
13
1214
1011
9
English
11
INTRODUCTION
No Item
1. HDMI 1 / MHL Connector N/A √
a) HDMI 2 Connector
2.
b) HDMI Connector
USB Power Out (5V 1A) Connector / MOUSE / SERVICE
3.
Connector
4. a) VGA-IN 1 / YPbPr Connector and
VGA-IN 2 / YPbPr Connector
b) VGA-IN / YPbPr Connector
5. S-VIDEO Connector N/A √
6. Composite Connector √ √
7. Audio Out Connector √ √
8. Audio In Connector √ √ (x2)
9. Audio In / Mic In Connector N/A √
10. RJ-45 Connector N/A √
11. RS-232C Connector √ √
12. KensingtonTM Lock Port √ √
13. VGA-OUT / YPbPr Connector √ √
14. Power Socket √ √
Regulatory Name
Type 1 XGA/
WXGA
√ √
√* √*
√ √ (x2)
Type 2 XGA/
WXGA
“Note: √” means the item is supported, “N/A” means the item is not available.
Note:
Remote mouse requires special remote control.
*This model supports mouse / service capability.
English
12
INTRODUCTION
Keypad
11
10
1 2
9
7
8
3 4
No Item No Item
On/Standby LED
1.
Lamp LED
2.
Keystone Correction
3.
Temp LED
4.
Information
5.
Enter
7.
Menu
8.
Four Directional Select Keys
9.
Source
10.
Power
11.
6. Re-Sync
5
6
English
13
INTRODUCTION
3
V
O
L
T
S
CR2025
Remote control 1
10
11
1
12
2
3
13
14
4
4
5
6
15
2
7
16
8
9
17
18
No Item No Item
1. Power On / Off 10. IR LED Indicator
Keystone + / - 11. Freeze
2.
3. AV Mute 12. Aspect Ratio
4. Volume - / + 13. Mute
5. Enter 14. Four Directional Select Keys
6. Menu 15. 3D
7. HDMI 16. Video
8. VGA 17. Resync
9. Source 18. Brightness Mode
Note:
The actual remote control may vary depending on the region.
Some keys may have no function for models that do not support these features.
Before using the remote control for the rst time, remove the transparent insulation tape. See page 20
for battery installation.
INTRODUCTION
Freeze
Power Switch
L
R
V Keystone Volume
Page+
-
+
-
+
1 2
Menu33D
4
HDMI5VGA6Video
7
User18User29User3
Source
0
Resync
Page
-
Laser
Enter
Remote control 2
10
11
12
13
14
15
1
16
2
3
4
17
18
5
19
6
7
8
9
20
21
22
23
24
25
26
27
Note:
No Item No Item
1. Power On / Off 15. Brightness Mode
Freeze 16. Mouse On / Off
2.
3. Display Blank / Audio Mute 17. Mute
4. Mouse Left Click 18. Mouse Right Click
5. Enter 19. Four Directional Select Keys
6. Laser 20. Page -
7. Page + 21. Volume - / +
8. V Keystone - / + 22. 3D Menu On / Off
9. Menu 23. VGA
10. Aspect Ratio 24. Video
11. HDMI 25. User 3
12. User 2 26. Numeric Keypad (0-9)
13. User 1 27. Resync
14. Source
The actual remote control may vary depending on the region.
Some keys may have no function for models that do not support these features
14
English
SETUP AND INSTALLATION
Installing the projector
Your projector is designed to be installed in one of four possible positions.
Your room layout or personal preference will dictate which installation location you select. Take into consideration
the size and position of your screen, the location of a suitable power outlet, as well as the location and distance
between the projector and the rest of your equipment.
Table mount front Ceiling mount front
Table mount rear Ceiling mount rear
Projector should be placed at on a surface and 90 degrees / perpendicular to the screen.
How to determine projector location for a given screen size, please refer to distance table on pages
59-60.
How to determine screen size for a given distance, please refer to distance table on pages 59-60.
The further away the projector is placed from the screen the projected image size increases and vertical Note:
offset also increases proportionally.
IMPORTANT!
Do not operate the projector in any orientation other that table top or ceiling mount. The projector should
be horizontal and not tilted either forwards/backwards or left/right. Any other orientation will invalidate
the warranty and may shorten the lifetime of the projector lamp or the projector itself. For none standard
installation advise please contact Optoma.
English
15
English
16
SETUP AND INSTALLATION
Audio Out
Audio In
VIDEO
VGA-IN / YPbPr
RS-232C
VGA-OUT / YPbPr
HDMI
USB Power
MOUSE /
SERVICE
Out (5V 1.0A)
MOLEX
MOLEX
Connecting sources to the projector
Type 1 XGA/ WXGA
16
3
2
13
7
6
15
4
11
9
14
12
English
17
SETUP AND INSTALLATION
HDMI 1 / MHL
Audio In
Audio Out
VIDEO
VGA-IN 1 / YPbPr
RS-232C
VGA-IN 2 / YPbPr
HDMI 2
USB Power
MOUSE /
SERVICE
Out (5V 1.0A)
VGA-OUT / YPbPr
S-VIDEO
Audio In /Mic In
RJ-45
MOLEX
MOLEX
Type 2 XGA/ WXGA
16
3
1
2
4
5
7
6
15
14
13
12
11
10
8
9
No Item
1. MHL Cable
2.
HDMI Cable
3. RCA Component Cable
4. VGA In Cable
5. S-Video Cable
6. Video Cable
7. Audio In Cable
8. Microphone In Cable
9. Audio Out Cable
Type 1 XGA/
Regulatory Name
WXGA
Type 2 XGA/
WXGA
N/A √
√ √
√ √
√ √
N/A √
√ √
√ √
N/A √
√ √
English
18
SETUP AND INSTALLATION
No Item
10. RJ-45 Cable
11. RS232C Cable
12. USB Cable (mouse control)
13. VGA Out Cable
14. USB Power Cable
15. HDMI Stick
16. Power Cord
“Note: √” means the item is supported, “N/A” means the item is not available.
Regulatory Name
Type 1 XGA/
WXGA
N/A √
√ √
√ √
√ √
√ √
√ √
√ √
Type 2 XGA/
WXGA
English
19
SETUP AND INSTALLATION
Adjusting the projector image
Image height
The projector is equipped with elevator feet for adjusting the image height.
Locate the adjustable foot you wish to adjust on the underside of the projector.1.
Rotate the adjustable foot clockwise or counterclockwise to raise or lower the projector.2.
Zoom and focus
To adjust the image size, turn the zoom lever clockwise or counterclockwise to increase or decrease
the projected image size.
To adjust the focus, turn the focus ring clockwise or counterclockwise until the image is sharp and
legible.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
Zoom Lever
Focus Ring
The projector will focus at a distance of 1m to 10m.Note:
English
20
SETUP AND INSTALLATION
3
V
O
L
T
S
CR2025
M
3
V
O
L
T
S
CR2025
Installing / replacing the batteries
Press rmly and slide the battery cover off.1.
Install new battery into the compartment. Remove the old battery and 2.
install new one (CR2025). Ensure that the side with a “+” is facing
up.
Put the cover back.3.
CAUTION: To ensure safe operation, please observe the following precautions:
Use CR2025 type battery.
Avoid contact with water or liquid.
Do not expose the remote control to moisture or heat.
Do not drop the remote control.
If the battery has leaked in the remote control, carefully wipe the case clean and install new battery.
Risk of an explosion if battery is replaced by an incorrect type.
Dispose of used battery according to the instructions.
English
21
SETUP AND INSTALLATION
Effective range
Infra-Red (IR) remote control sensor is located on top of the projector. Ensure to hold the remote control at an
angle within 30 degrees perpendicular to the projector’s top IR remote control sensor to function correctly. The
distance between the remote control and the sensor should not be longer than 6 meters (~ 20 feet).
When pointing the remote control directly (0 degrees angle) on the IR sensor, the distance between the Note:
remote control and the sensor should not be longer than 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote control and the IR sensor on the projector
that might obstruct the infra-red beam.
Make sure the IR transmitter of the remote control is not being shined by sunlight or uorescent lamps
directly.
Please keep the remote controller away from uorescent lamps for over 2 meters or the remote
controller might become malfunction.
If the remote control is close to Inverter-Type uorescent lamps, it might become ineffective from time
to time.
If the remote control and the projector are within a very short distance, the remote control might
become ineffective.
When you aim at the screen, the effective distance is less than 6 meters from the remote control to the
screen and reecting the IR beams back to the projector. However, the effective range might change
according to screens.
Approx. 15°
USING THE PROJECTOR
Powering on / off the projector
or
Powering on
The rst time the projector is turned on, you will be prompted to select the preferred language, projectionNote:
orientation, and other settings.
Powering off
Securely connect the power lead and signal/source cable. When connected, the On/Standby LED will 1.
turn red.
Turn on the projector by pressing the 2. " " either on the projector keypad or the remote control.
A start up screen will display in approximately 10 seconds and the On/Standby LED will be ashing 3.
green or ashing blue.
Turn off the projector by pressing the 1. " " either on the projector keypad or the remote control.
The following message will be displayed:2.
Power Off
Power Off?
Press power key again.
Press the 3. " " again to conrm, otherwise the message will disappear after 15 seconds. When you
press the " " button for the second time, the projector will shut down.
The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/4.
Standby LED will ash green or ash blue. When the On/Standby LED turns solid red, this indicates
the projector has entered standby mode. If you wish to turn the projector back on, you must wait until
the cooling cycle has nished and the projector has entered standby mode. When the projector is in
standby mode, simply press the " " button again to turn on the projector.
Disconnect the power lead from the electrical outlet and the projector.5.
22
It is not recommended that the projector is turned on immediately, right after a power off procedure.Note:
English
Loading...