DLP® Projector
User manual
TABLE OF CONTENTS
SAFETY ............................................................................................... 4
Important Safety Instruction....................................................................................................... 4
3D Safety Information ................................................................................................................ 5
Copyright ................................................................................................................................... 6
Disclaimer .................................................................................................................................. 6
Trademark Recognition ............................................................................................................. 6
FCC ........................................................................................................................................... 7
Declaration of Conformity for EU countries ............................................................................... 7
WEEE ........................................................................................................................................ 7
INTRODUCTION .................................................................................. 8
Package Overview..................................................................................................................... 8
Standard accessories ................................................................................................................ 8
Optional accessories ................................................................................................................. 8
Product Overview ...................................................................................................................... 9
Connections.............................................................................................................................. 10
Keypad ..................................................................................................................................... 11
Remote control ......................................................................................................................... 12
SETUP AND INSTALLATION ............................................................. 13
Installing the projector .............................................................................................................. 13
Connecting sources to the projector ......................................................................................... 15
Adjusting the projector image ................................................................................................... 16
Remote setup ........................................................................................................................... 17
USING THE PROJECTOR .................................................................. 19
Powering on / off the projector.................................................................................................. 19
Selecting an input source ......................................................................................................... 20
USING THE PROJECTOR .................................................................. 21
Menu navigation and features .................................................................................................. 21
OSD Menu tree......................................................................................................................... 22
Display image settings menu.................................................................................................... 31
Display 3D menu ...................................................................................................................... 33
Display aspect ratio menu ........................................................................................................ 34
Display edge mask menu ......................................................................................................... 37
Display zoom menu .................................................................................................................. 37
Display image shift menu ......................................................................................................... 37
Display geometric correction menu .......................................................................................... 37
Audio mute menu ..................................................................................................................... 38
Audio volume menu .................................................................................................................. 38
Setup projection menu.............................................................................................................. 38
2
English
Setup screen type menu........................................................................................................... 38
Setup lamp settings menu ........................................................................................................ 38
Setup lter settings menu ......................................................................................................... 38
Setup power settings menu ...................................................................................................... 39
Setup security menu ................................................................................................................. 40
Setup HDMI link settings menu ................................................................................................ 40
Setup test pattern menu ........................................................................................................... 40
Setup remote settings menu..................................................................................................... 40
Setup projector ID menu........................................................................................................... 41
Setup options menu.................................................................................................................. 41
Setup reset all menu................................................................................................................. 42
Network WLAN menu ............................................................................................................... 42
Network LAN menu .................................................................................................................. 42
Network control menu............................................................................................................... 43
Setup network control settings menu ....................................................................................... 44
Info menu.................................................................................................................................. 49
MAINTENANCE .................................................................................. 50
Replacing the lamp ................................................................................................................... 50
Installing and cleaning the dust lter ........................................................................................ 52
ADDITIONAL INFORMATION ............................................................ 53
Compatible resolutions ............................................................................................................. 53
Image size and projection distance .......................................................................................... 55
Projector dimensions and ceiling mount installation ................................................................. 57
RS232 protocol function list ...................................................................................................... 58
IR remote codes ....................................................................................................................... 66
Troubleshooting ........................................................................................................................ 68
Warning indicators .................................................................................................................... 69
Specications ........................................................................................................................... 72
Optoma global ofces ............................................................................................................... 73
English
3
SAFETY
The lightning ash with arrow head within an equilateral triangle is
intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufcient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
Please follow all warnings, precautions and maintenance as recommended in this user's guide.
Important Safety Instruction
RG2 IEC
Do not stare into the beam, RG2.
As with any bright source, do not stare into the direct beam, RG2 IEC 62471-5:2015.
Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from
over heating, it is recommended to install the projector in a location that does not block ventilation.
As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the
projector in an enclosure such as a book case or a cabinet that restricts air ow.
To reduce the risk of re and/or electric shock, do not expose the projector to rain or moisture. Do not
install near heat sources such as radiators, heaters, stoves or any other apparatus such as ampliers
that emits heat.
Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short
out parts that could result in re or electric shock.
Do not use under the following conditions:
± In extremely hot, cold or humid environments.
(i) Ensure that the ambient room temperature is within 5°C ~ 40°C
(ii) Relative humidity is 10% ~ 85%
± In areas susceptible to excessive dust and dirt.
± Near any appliance generating a strong magnetic eld.
± In direct sunlight.
Do not use the projector in places where ammable gases or explosives gases may be present in the
atmosphere. The lamp inside the projector becomes very hot during operation and the gases may
ignite and result in a re.
Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be
(but not limited to):
± Unit has been dropped.
± Power supply cord or plug has been damaged.
4
± Liquid has been spilled on to the projector.
± Projector has been exposed to rain or moisture.
± Something has fallen in the projector or something is loose inside.
Do not place the projector on an unstable surface. The projector may fall over resulting in injury or the
projector may become damaged.
Do not block the light coming out of the projector lens when in operation. The light will heat the object
and cause melt, cause burns, or start a re.
English
Please do not open or disassemble the projector as this may cause electric shock.
Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous
voltages or other hazards. Please call Optoma before you send the unit for repair.
See projector enclosure for safety related markings.
The unit should only be repaired by appropriate service personnel.
Only use attachments/accessories specied by the manufacturer.
Do not look into straight into the projector lens during operation. The bright light may harm your eyes.
When replacing the lamp, please allow the unit to cool down. Follow instructions as described on
pages 50-51.
This projector will detect the life of the lamp itself. Please be sure to change the lamp when it shows
warning messages.
Reset the "Lamp Reset" function from the on-screen display “Setup > Lamp Settings” menu after
replacing the lamp module.
When switching the projector off, please ensure the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the projector to cool down.
When the lamp is approaching to the end of its life time, the message "Lamp life exceeded." will show
on the screen. Please contact your local reseller or service center to change the lamp as soon as
possible.
Turn off and unplug the power plug from the AC outlet before cleaning the product.
Use a soft dry cloth with mild detergent to clean the display housing. Do not use abrasive cleaners,
waxes or solvents to clean the unit.
Disconnect the power plug from AC outlet if the product is not being used for a long period of time.
Note: When the lamp reaches the end of its life, the projector will not turn back on until the lamp module has been
replaced. To replace the lamp, follow the procedures listed under “Replacing the Lamp” section on pages
50-51.
Do not setup the projector in places where it might be subjected to vibration or shock.
Do not touch the lens with bare hands
Remove battery/batteries from remote control before storage. If the battery/batteries are left in the
remote for long periods, they may leak.
Do not use or store the projector in places where smoke from oil or cigarettes may be present, as it
can adversely affect the quality of the projector performance.
Please follow the correct projector orientation installation as non standard installation may affect the
projector performance.
Use a power strip and or surge protector. As power outages and brown-outs can KILL devices.
3D Safety Information
Please follow all warnings and precautions as recommended before you or your child use the 3D function.
Warning
Children and teenagers may be more susceptible to health issues associated with viewing in 3D and should be
closely supervised when viewing these images.
Photosensitive Seizure Warning and Other Health Risks
Some viewers may experience an epileptic seizure or stroke when exposed to certain ashing images
or lights contained in certain Projector pictures or video games. If you suffer from, or have a family
history of epilepsy or strokes, please consult with a medical specialist before using the 3D function.
Even those without a personal or family history of epilepsy or stroke may have an undiagnosed
condition that can cause photosensitive epileptic seizures.
Pregnant women, the elderly, sufferers of serious medical conditions, those who are sleep deprived or
under the inuence of alcohol should avoid utilizing the unit's 3D functionality.
English
5
If you experience any of the following symptoms, stop viewing 3D pictures immediately and consult a
medical specialist: (1) altered vision; (2) light-headedness; (3) dizziness; (4) involuntary movements
such as eye or muscle twitching; (5) confusion; (6) nausea; (7) loss of awareness; (8) convulsions;
(9) cramps; and/ or (10) disorientation. Children and teenagers may be more likely than adults
to experience these symptoms. Parents should monitor their children and ask whether they are
experiencing these symptoms.
Watching 3D projection may also cause motion sickness, perceptual after effects, disorientation, eye
strain and decreased postural stability. It is recommended that users take frequent breaks to lessen
the potential of these effects. If your eyes show signs of fatigue or dryness or if you have any of the
above symptoms, immediately discontinue use of this device and do not resume using it for at least
thirty minutes after the symptoms have subsided.
Watching 3D projection while sitting too close to the screen for an extended period of time may
damage your eyesight. The ideal viewing distance should be at least three times the screen height. It
is recommended that the viewer's eyes are level with the screen.
Watching 3D projection while wearing 3D glasses for an extended period of time may cause a
headache or fatigue. If you experience a headache, fatigue or dizziness, stop viewing the 3D
projection and rest.
Do not use the 3D glasses for any other purpose than for watching 3D projection.
Wearing the 3D glasses for any other purpose (as general spectacles, sunglasses, protective goggles,
etc.) may be physically harmful to you and may weaken your eyesight.
Viewing in 3D projection may cause disorientation for some viewers. Accordingly, DO NOT place your
3D PROJECTOR near open stairwells, cables, balconies, or other objects that can be tripped over, run
into, knocked down, broken or fallen over.
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright
laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced
without written consent of the author.
© Copyright 2017
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations
or warranties with respect to the contents hereof and specically disclaims any implied warranties of
merchantability or tness for any particular purpose. The manufacturer reserves the right to revise this publication
and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any
person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending
applications in other countries throughout the world.
HDMI, the HDMI Logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
DLP®, DLP Link and the DLP logo are registered trademarks of Texas Instruments and BrilliantColorTM is a
trademark of Texas Instruments.
All other product names used in this manual are the properties of their respective owners and are
Acknowledged.
MHL, Mobile High-Denition Link and the MHL Logo are trademarks or registered trademarks of MHL Licensing,
LLC.
English
6
FCC
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause
harmful interference to radio or television reception, which can be determined by turning the device off and on is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC
regulations.
Caution
Changes or modications not expressly approved by the manufacturer could void the user's authority, which is
granted by the Federal Communications Commission, to operate this projector.
Operation Conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Remarque à l'intention des utilisateurs canadiens
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.
Declaration of Conformity for EU countries
EMC Directive 2014/30/EU (including amendments)
Low Voltage Directive 2014/35/EU
RED 2014/53/EU (if product has RF function)
RoHS Directive 2011/65/EU (if product has RF function)
WEEE
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure
utmost protection of the global environment, please recycle it.
English
7
INTRODUCTION
Package Overview
Carefully unpack and verify that you have the items listed below under standard accessories. Some of the items
under optional accessories may not be available depending on the model, specication and your region of
purchase. Please check with your place of purchase. Some accessories may vary from region to region.
The warranty card is only supplied in some specic regions. Please consult your dealer for detailed information.
Standard accessories
Power Switch
Freeze
L
R
Enter
-
Page+Laser
Page
Keystone Volume
-+-
+
1 2
Menu33D
4
HDMI5VGA6Video
7
User18User29User3
Source0Resync
Projector Remote control Power lead
CD User Manual
Warranty Card
Basic User Manual
Documentation
Note: The remote control is shipped with the batteries.
Optional accessories
Lens cap
Carry bag
VGA cable
Note: Optional accessories vary depending on model, specication and region.
English
8
INTRODUCTION
Product Overview
1 32 54
6
78
9
10
13
12 11
Note: Do not block projector inlet or outlet air vents.
(*) Optional accessory varies depending on model, specication, and region.
No Item No Item
1. Lamp Cover 8. Lens
2.
Focus Ring
Ventilation (inlet)
9.
3. Zoom Lever 10. Ventilation (outlet)
4. IR Receiver 11. Kensington
5. Keypad 12. Power Socket
6. Tilt-Adjustment Foot 13. Input / Output
7. Security Bar
TM
Lock Port
English
9
INTRODUCTION
Connections
RJ-45
7
8
AUDIO IN
AUDIO OUT
HDMI 1
USB
USB READER/DISPLAY
1 3
2
HDMI 2/MHL
VGA-IN/YPbPr VGA-OUT/YPbPr
VIDEO
RS-232C
5 64
101112 9
No Item No Item
1. HDMI 1 Connector 7. RJ-45 Connector
USB READER/DISPLAY
2.
Connector*
8. AUDIO IN Connector
3. HDMI 2/MHL Connector 9. AUDIO OUT Connector
4. VIDEO Connector 10. RS-232C Connector
5. VGA-IN/YPbPr Connector 11. KensingtonTM Lock Port
6. VGA-OUT/YPbPr Connector 12. Power Socket
Note:
*Supports 5V/1A power output only if MHL source is not detected. If MHL source is detected, the
5V/1A power output is disabled automatically.
*Supports WiFi dongle.
*Use the USB READER/DISPLAY connector as follows:
– Network Display: (a) Plug in the WiFi USB dongle; (b) Use the HDcastPro APP on your mobile phone.
– USB Display for iOS and Android devices.
– Multimedia: Display pictures and documents from the USB disk directly.
10
English
INTRODUCTION
Keypad
1 293 4
12
11
10
8
7
5
6
No Item No Item
1. On/Standby LED 7. IR Receiver
2.
Lamp LED
8.
Enter
3. Keystone Correction 9. Menu
4. Temp LED 10. Four Directional Select Keys
5. Info 11. Source
6. Re-Sync 12. Power
English
11
INTRODUCTION
Remote control
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Power Switch
Freeze
L
Enter
-
Page
Keystone Volume
-
+
1 2
Menu33D
4
HDMI5VGA6Video
7
User18User29User3
Source
Page+Laser
-
0
Resync
16
17
R
18
19
20
+
21
22
23
24
25
26
27
15
No Item No Item
1. Power On / Off 15. Brightness Mode
Freeze 16. Mouse On / Off
2.
3. Display Blank / Audio Mute 17. Mute
4. Mouse Left Click 18. Mouse Right Click
5. Enter 19. Four Directional Select Keys
6. Laser 20. Page +
7. Page - 21. Volume - / +
8. Keystone - / + 22. 3D Menu On / Off
9. Menu 23. VGA
10. Aspect Ratio 24. Video
11. HDMI 25. User 3
12. User 2 26. Numeric Keypad (0-9)
13. User 1 27. Resync
14. Source
Note: Some keys may have no function for models that do not support these features.
12
English
SETUP AND INSTALLATION
Installing the projector
Your projector is designed to be installed in one of four possible positions.
Your room layout or personal preference will dictate which installation location you select. Take into consideration
the size and position of your screen, the location of a suitable power outlet, as well as the location and distance
between the projector and the rest of your equipment.
Table mount front Ceiling mount front
Table mount rear Ceiling mount rear
Projector should be placed at on a surface and 90 degrees / perpendicular to the screen.
How to determine projector location for a given screen size, please refer to distance table on pages
55-56.
How to determine screen size for a given distance, please refer to distance table on pages 55-56.
Note: The further away the projector is placed from the screen the projected image size increases and vertical
offset also increases proportionally.
IMPORTANT!
Do not operate the projector in any orientation other that table top or ceiling mount. The projector should
be horizontal and not tilted either forwards/backwards or left/right. Any other orientation will invalidate
the warranty and may shorten the lifetime of the projector lamp or the projector itself. For none standard
installation advise please contact Optoma.
English
13
SETUP AND INSTALLATION
Projector installation notice
Place the projector in a horizontal position.
The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed
in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically,
and may lead to other unpredictable damages.
15°
-15°
Allow at least 20 cm clearance around the exhaust vent.
Minimum 100mm
(3.94 inches)
Minimum 100mm
(3.94 inches)
Minimum 200mm
(7.87 inches)
Minimum 100mm
(3.94 inches)
Minimum 200mm
(7.87 inches)
Minimum 200mm
(7.87 inches)
14
Ensure that the intake vents do not recycle hot air from the exhaust vent.
When operating the projector in an enclosed space, ensure that the surrounding air temperature within
the enclosure does not exceed operation temperature while the projector is running, and the air intake
and exhaust vents are unobstructed.
All enclosures should pass a certied thermal evaluation to ensure that the projector does not recycle
exhaust air, as this may cause the device to shutdown even if the enclosure temperature is with the
acceptable operation temperature range.
English
SETUP AND INSTALLATION
Connecting sources to the projector
16
1
HDMI 1
USB
USB READER/DISPLAY
15
14 13
2 3
HDMI 2/MHL
MOLEX
12
MOLEX
VGA-IN/YPbPr VGA-OUT/YPbPr
VIDEO
11
RS-232C
10
4
5
6
AUDIO IN
RJ-45
9
AUDIO OUT
7
8
No Item No Item
1. HDMI Cable 9. RJ-45 Cable
HDMI / MHL Cable
2.
RS-232C Cable
10.
3. Video Cable 11. VGA In Cable
4. RCA Component Cable 12. WiFi Dongle
5. VGA Out Cable 13. USB Cable (mouse control)
6. Audio In Cable 14. Power Cord
7. Audio Out Cable 15. USB Power Supply (5V/1A)
8. Audio In Cable 16. HDMI Dongle
English
15
SETUP AND INSTALLATION
Adjusting the projector image
Image height
The projector is equipped with elevator feet for adjusting the image height.
1. Locate the adjustable foot you wish to adjust on the underside of the projector.
2. Rotate the adjustable foot clockwise or counterclockwise to raise or lower the projector.
Zoom and focus
To adjust the image size, turn the zoom lever clockwise or counterclockwise to increase or decrease
the projected image size.
To adjust the focus, turn the focus ring clockwise or counterclockwise until the image is sharp and
legible.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
Zoom Lever
Focus Ring
Note: The projector will focus at a distance of 1m to 10.
English
16
SETUP AND INSTALLATION
Remote setup
Installing / replacing the batteries
Two AAA size batteries are supplied for the remote control.
1. Remove the battery cover on the back of the remote control.
2. Insert AAA batteries in the battery compartment as illustrated.
3. Replace back cover on remote control.
Note: Replace only with the same or equivalent type batteries.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
Do not mix batteries of different types. Different types of batteries have different characteristics.
Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or
cause chemical leakage in old batteries.
Remove batteries as soon as they are depleted. Chemicals that leak from batteries that come in
contact with skin can cause a rash. If you nd any chemical leakage, wipe thoroughly with a cloth.
The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
If you will not be using the remote control for an extended period of time, remove the batteries.
When you dispose of the batteries, you must obey the law in the relative area or country.
Effective range
Infra-Red (IR) remote control sensor is located on the top side of the projector. Ensure to hold the remote control
at an angle within 30 degrees perpendicular to the projector’s IR remote control sensor to function correctly. The
distance between the remote control and the sensor should not be longer than 6 meters (~ 20 feet).
Make sure that there are no obstacles between the remote control and the IR sensor on the projector
that might obstruct the infra-red beam.
Make sure the IR transmitter of the remote control is not being shined by sunlight or uorescent lamps
directly.
Please keep the remote controller away from uorescent lamps for over 2 meters or the remote
controller might become malfunction.
If the remote control is closed to Inverter-Type uorescent lamps, it might become ineffective from time
to time.
If the remote control and the projector are within a very short distance, the remote control might
become ineffective.
When you aim at the screen, the effective distance is less than 5 m from the remote control to the
screen and reecting the IR beams back to the projector. However, the effective range might change
according to screens.
English
17
SETUP AND INSTALLATION
Approx. ±15°
Resync
+
Page+Laser
R
Source
0
User18User29User3
7
HDMI5VGA6Video
4
Menu33D
1 2
+
-
-
Keystone Volume
Page
-
Enter
L
Freeze
Power Switch
18
English
USING THE PROJECTOR
Freeze
Power Switch
Powering on / off the projector
or
Power Switch
Freeze
L
Enter
-
Page
Keystone Volume
-+-
1 2
Menu33D
4
HDMI5VGA6Video
7
User18User29User3
Source0Resync
R
Page+Laser
+
Powering on
1. Securely connect the power lead and signal/source cable. When connected, the On/Standby LED will
turn red.
2. Turn on the projector by pressing the " " either on the projector keypad or the remote control.
3. A start up screen will display in approximately 10 seconds and the On/Standby LED will be ashing
green or ashing blue.
Note: The rst time the projector is turned on, you will be prompted to select the preferred language, projection
orientation, and other settings.
Powering off
1. Turn off the projector by pressing the " " either on the projector keypad or the remote control.
2. The following message will be displayed:
Power Off
Power Off?
Press power key again.
3. Press the " " again to conrm, otherwise the message will disappear after 10 seconds. When you
press the " " button for the second time, the projector will shut down.
4. The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/
Standby LED will ash green or ash blue. When the On/Standby LED turns solid red, this indicates
the projector has entered standby mode. If you wish to turn the projector back on, you must wait until
the cooling cycle has nished and the projector has entered standby mode. When the projector is in
standby mode, simply press the " " button again to turn on the projector.
5. Disconnect the power lead from the electrical outlet and the projector.
Note: It is not recommended that the projector is turned on immediately, right after a power off procedure.
English
19
USING THE PROJECTOR
Freeze
Power Switch
L
R
Keystone Volume
Page
-
-
+
-
+
1 2
Menu
3
3D
4
HDMI
5
VGA6Video
7
User18User29User3
Source
0
Resync
Page+Laser
Enter
Selecting an input source
Turn on the connected source that you want to display on the screen, such as computer, notebook, video player,
etc. The projector will automatically detect the source. If multiple sources are connected, push the source button on
the projector keypad or the remote control to select the desired input.
or
Power Switch
Freeze
L
R
Enter
-
Page
Keystone Volume
-+-
1 2
Menu33D
4
HDMI5VGA6Video
7
User18User29User3
Source0Resync
Page+Laser
+
English
20
USING THE PROJECTOR
Menu navigation and features
The projector has multilingual on-screen display menus that allow you to make image adjustments and change a
variety of settings. The projector will automatically detect the source.
1. To open the OSD menu, press on the remote control or the projector keyboard.
2. When OSD is displayed, use keys to select any item in the main menu. While making a selection
on a particular page, press or key to enter sub menu.
3. Use keys to select the desired item in the sub menu and then press or key to view further
settings. Adjust the settings by using keys.
4. Select the next item to be adjusted in the sub menu and adjust as described above.
5. Press the or to conrm, and the screen will return to the main menu.
6. To exit, press the or again. The OSD menu will close and the projector will automatically save
the new settings.
Main Menu
Sub Menu
Display
Image Settings
3D
Aspect Ratio
Edge Mask
Zoom
Image Shift
Geometric Correction
Select Exit Enter
Navigation guide
Settings
English
21
USING THE PROJECTOR
OSD Menu tree
Main
Menu
Display Image Settings
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Presentation
Bright
Cinema
Display Mode
[Data]
Wall Color [Data]
Brightness -50~50
Contrast
Sharpness 1~15
Color -50~50
Tint -50~50
Film
Video
Graphics
Gamma
Color Settings
Standard(2.2)
1.8
2.0
2.4
BrilliantColor
Color
Temperature
[Data model]
Color Matching
TM
Color
Saturation -50~50 [Default:0]
Hue -50~50 [Default:0]
Gain -50~50 [Default:0]
Game
sRGB
DICOM SIM.
User
3D
Off [Default]
BlackBoard
Light Yellow
Light Green
Light Blue
Pink
Gray
-50~50
1~10
Warm
Medium
Cool
R [Default]
G
B
C
Y
M
W
22
English
USING THE PROJECTOR
Main
Menu
Display Image Settings
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Color Settings
Signal
Brightness Mode
[Lamp Base Data]
Color Matching
RGB Gain/Bias
Color Space [Not
HDMI Input]
Color Space
[HDMI Input]
RGB Channel
White Level -50~50
Black Level -50~50
Saturation -50~50
Hue -50~50
IRE
Exit
Automatic
Frequency
Phase
H. Position -5~5 (depends on signal) [Default: 0]
V. Position -5~5 (depends on signal) [Default: 0]
Exit
Reset
Exit
Red Gain -50~50
Green Gain -50~50
Blue Gain -50~50
Red Bias -50~50
Green Bias -50~50
Blue Bias -50~50
Reset
Exit
Cancel [Default]
Yes
Cancel [Default]
Yes
Auto [Default]
RGB
YUV
Auto [Default]
RGB(0~255)
RGB(16~235)
YUV
Normal [Default]
Red
Green
Blue
0
7.5
Off
On [Default]
-10~10 (depends on signal)
[Default: 0]
0~63 (depends on signal)
[Default: 0]
Bright [Default]
Eco
Dynamic
Eco+
Reset
English
23
USING THE PROJECTOR
Main
Menu
Display
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Off
3D Mode
3D->2D
3D
3D Format
3D sync invert
Aspect Ratio
Edge Mask 0~10 [Default: 0]
Zoom -5~25 [Default: 0]
H: 0; V: -100
DLP [Default]
IR
3D [Default]
L
R
Auto [Default]
SBS
Top and Bottom
Frame Sequential
On
Off [Default]
4:3
16:9
16:10 [WXGA WUXGA models]
LBX [except SVGA XGA models]
Native
Auto
Audio
H: -100; V: 0
H: 100; V: 0
Image shift
Geometric
Correction
Mute
Volume 0-10 [Default: 5]
H: 0; V: 100
H: -100; V: 0
H: 0; V: -100
H: 100; V: 0
H: 0; V: 100
Four Corner
Adjustment
H Keystone -20~20 [Default:0]
V Keystone -20~20 [Default:0]
Auto Keystone
Reset
[Default:0]
Off
On [Default]
Off [Default]
On
24
English
USING THE PROJECTOR
Main
Menu
Setup
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Front [Default]
Projection
Screen Type
Lamp Settings
Filter Settings
Power Settings
Security
[WXGA WUXGA
models]
Lamp Reminder
Lamp Reset
Optional Filter
Installed
Filter Usage
Hours
Filter Reminder
Filter Reset
Direct Power On
Signal Power On
Auto Power Off
(min)
Sleep Timer
Quick Resume
Power Mode
(Standby)
USB Power
(Standby)
Security
Security Timer
Change
Password
Sleep Timer
(min)
Always On
Month
Day
Hour
Rear
Ceiling-top
Rear-top
16:9
16:10 [Default]
Off
On [Default]
Cancel [Default]
Yes
Yes
No [Default]
(Read only)
Off
300hr
500hr [Default]
800hr
1000hr
Cancel [Default]
Yes
Off [Default]
On
Off [Default]
On
0~180 (5 min increments)
[Default: 20]
0~990 (30 min increments)
[Default: 0]
Yes
No [Default]
Off
On [Default]
Active
Eco [Default]
Off [Default]
On
English
25
USING THE PROJECTOR
Main
Menu
Setup
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
HDMI Link
Settings
Test Pattern
Remote
Settings
[Depends on
remote]
HDMI Link
IR Function
User1
User2
Off
On
Green Grid
Magenta Grid
White Grid
White
Off
On
Off
HDMI 2
Test Pattern
LAN
Brightness
Contrast
Sleep Timer
Color Matching
Color Temp
Gamma
Projection
Lamp Settings
Zoom
Freeze
MHL
HDMI 2
Test Pattern
LAN
Brightness
Contrast
Sleep Timer
Color Matching
Color Temp
Gamma
Projection
Lamp Settings
Zoom
Freeze
MHL
26
English
USING THE PROJECTOR
Main
Menu
Setup
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
HDMI 2
Test Pattern
LAN
Brightness
Contrast
Remote
Settings
[Depends on
remote]
Projector ID 00~99
Options
User3
Language
Sleep Timer
Color Matching
Color Temp
Gamma
Projection
Lamp Settings
Zoom
Freeze
MHL
English [Default]
Deutsch
Français
Italiano
Español
Português
Polski
Nederlands
Svenska
Norsk
Dansk
Suomi
ελληνικά
繁體中文
簡体中文
日本語
한국어
Русский
Magyar
Čeština
Closed
Captioning
ไทย
Türkçe
Tiếng Việt
Bahasa Indonesia
Română
Slovenčina
CC1
CC2
Off [Default]
English
27
USING THE PROJECTOR
Main
Menu
Setup Options
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Menu Settings
Auto Source
Input Source
Input Name
High Altitude
Display Mode
Lock
Keypad Lock
Information Hide
Background
Color
Menu Location
Menu Timer
HDMI1
HDMI2/MHL
VGA
Video
Network Display
USB Display
Multimedia
Top left
Top right
Center [Default]
Bottom left
Bottom right
Off
5sec
10sec [Default]
Off [Default]
On
HDMI1
HDMI2/MHL
VGA
Video
Network Display
USB Display
Multimedia
Default [Default]
Custom
Default [Default]
Custom
Default [Default]
Custom
Default [Default]
Custom
Default [Default]
Custom
Default [Default]
Custom
Default [Default]
Custom
Off [Default]
On
Off [Default]
On
Off [Default]
On
Off [Default]
On
None [Default]
Blue
Red
28
English
USING THE PROJECTOR
Main
Menu
Setup
Network
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Green
Grey
Logo
Cancel [Default]
Yes
Cancel [Default]
Yes
Off
On [Default]
Connected (read only)
Disconnected (read only)
(read only) (depends on network
card)
Infrastructure (read only)
Ad-hoc (read only) [Default]
Off [Default]
On
Off
On [Default]
Note: Port 41794.
Off
On [Default]
Note: Port 2023.
Off
On [Default]
Note: Port 4352
Off
On [Default]
Note: Port 9131
Off
On [Default]
Note: Port 23
Off
On [Default]
Note: Port 80
Options
Reset
WLAN
LAN
Control
Background
Color
Reset OSD
Reset to Default
WLAN
Network Status
MAC Address
IP Address 172.28.120.1 [Default] (read only)
SSID NetworkDisplay (read only)
Connection
Mode
Network Status (read only)
MAC Address (read only)
DHCP
IP Address 192.168.0.100 [Default]
Subnet Mask 255.255.255.0 [Default]
Gateway 192.168.0.254 [Default]
DNS 192.168.0.51 [Default]
Reset
Crestron
Extron
PJ Link
AMX Device
Discovery
Telnet
HTTP
English
29
USING THE PROJECTOR
Main
Menu
Information
Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Values
Regulatory
Serial Number
Source
Resolution 00x00
Refresh Rate 0.00Hz
Display Mode
Power
mode(standby)
Bright mode 0H
Eco mode 0H
Lamp Hours
Network Status
IP Address
Projector ID 00~99
Filter Usage
Hours
Brightness
Mode
FW Version
Dynamic mode 0H
Eco+ mode 0H
Total hours
System
LAN
MCU
AM
Note:
If the Signal setting is set to “Automatic”, the Phase and Frequency items are grayed out. If the
Signal setting is set to a specic input source, the Phase and Frequency items will appear for user to
manually tune and saved in settings.
The Lamp Reset in OSD will reset both Lamp Hours in OSD and Lamp Hours in service mode. The
Projection Hours in service mode will not be reset.
If you make changes to “IR Function”, “Projection”, or “Keypad Lock” functions, a conrmation
message will appear on the screen. Select “Yes” to save the settings.
Each display mode can be adjusted and saved the value.
In 3D timing mode, the Zoom and Edge Mask functions will be disabled to prevent from image break.
30
English
USING THE PROJECTOR
Display menu
Display image settings menu
Display Mode
There are many factory presets optimized for various types of images.
Presentation: This mode is suitable for showing PowerPoint presentations when the projector is
connected to the PC.
Bright: Maximum brightness from PC input.
Cinema: Select this mode for home theater.
Game: Select this mode to increase the brightness and response time level for enjoying video games.
sRGB: Standardized accurate color.
DICOM SIM.: This mode can project a monochrome medical image such as an X ray radiography,
MRI, etc.
User: Memorize user’s settings.
3D: To experience the 3D effect, you need to have 3D glasses. Make sure your PC/portable device
has a 120 Hz signal output quad buffered graphics card and a 3D Player installed.
Wall Color (Data mode)
Use this function to obtain an optimized screen image according to the wall color. Select between off, blackboard,
light yellow, light green, light blue, pink, and gray.
Brightness
Adjust the brightness of the image.
Contrast
The contrast controls the degree of difference between the lightest and darkest parts of the picture.
Sharpness
Adjust the sharpness of the image.
Color
Adjust a video image from black and white to fully saturated color.
Tint
Adjust the color balance of red and green.
Gamma
Set up gamma curve type. After the initial setup and ne tuning is completed, utilize the Gamma Adjustment steps
to optimize your image output.
Film: For home theater.
Video: For video or TV source.
Graphics: For PC / Photo source.
Standard(2.2): For standardized setting.
1.8/ 2.0/ 2.4: For specic PC / Photo source.
English
31
USING THE PROJECTOR
Color Settings
Congure the color settings.
BrillianColorTM: This adjustable item utilizes a new color-processing algorithm and enhancements to
enable higher brightness while providing true, more vibrant colors in picture.
Color Temperature (data-mode only): Select a color temperature from Warm, Medium, or Cool.
Color Matching: Select the following options:
± Color: Adjust the red (R), green (G), black (B), cyan (C), yellow (Y), magenta (M), and white (W)
level of the image.
± Saturation: Adjust a video image from black and white to fully saturated color.
± Hue: Adjust the color balance of red and green.
± Gain: Adjust the image brightness.
± Reset: Return the factory default settings for color matching.
± Exit: Exit the “Color Matching” menu.
RGB Gain/Bias: This settings allows to congure the brightness (gain) and contrast (bias) of an
image.
± Reset: Return the factory default settings for RGB gain/bias.
± Exit: Exit the “RGB Gain/Bias” menu.
Color Space (non-HDMI input only): Select an appropriate color matrix type from the following:
AUTO, RGB, or YUV.
Color Space (HDMI input only): select an appropriate color matrix type from the following: Auto,
RGB(0-255), RGB(16-235), and YUV.
RGB Channel: Select from normal, red, green, or blue channels.
White Level: Allow user to adjust White Level when inputting Video signals.
Black Level: Allow user to adjust Black Level when inputting Video signals.
Saturation: Adjust a video image from black and white to fully saturated color.
Hue: Adjust the color balance of red and green.
IRE: Allow user to adjust IRE value when inputting Video signals.
Note: IRE is only available with NTSC video format.
Exit: Exit the “Color Settings” menu.
Signal
Adjust the signal options.
Automatic: Congure automatically the signal (the frequency and phase items are grayed out). If
automatic is disabled, the frequency and phase items will appear for tuning and saving the settings.
Frequency: Change the display data frequency to match the frequency of your computer’s graphic
card. Use this function only if the image appears to icker vertically.
32
Phase: Synchronize the signal timing of the display with the graphic card. If the image appears to be
unstable or ickers, use this function to correct it.
H. Position: Adjust the horizontal positioning of the image.
V. Position: Adjust the vertical positioning of the image.
Exit: Exit the “Signal” menu.
English
USING THE PROJECTOR
Brightness Mode (Lamp base data)
Adjust the brightness mode settings for lamp-based projectors.
Bright: Choose “Bright” to increase the brightness.
Eco: Choose “Eco” to dim the projector lamp which will lower power consumption and extend the lamp
life.
Dynamic: Choose “Dynamic” to dim the lamp power which will be based on brightness level of the
content and adjust lamp power consumption between 100% and 30% dynamically. The lamp life will
be extended.
Eco+: When Eco+ mode is activated, the brightness level of the content is automatically detected to
signicantly reduced lamp power consumption (up to 70%) during periods of inactivity.
Reset
Return the factory default settings for color settings.
Display 3D menu
3D Mode
Use this option to disable the 3D function or select the appropriate the 3D function.
Off: Select “Off” to turn off 3D mode.
DLP: Select to use optimized settings for DLP 3D Glasses.
IR: Select “IR” to use optimized setting for IR 3D Glasses.
3D → 2D
Use this option to specify how the 3D content should appear on the screen.
3D: Display 3D signal.
L (Left): Display the left frame of 3D content.
R (Right): Display the right frame of 3D content.
3D Format
Use this option to select the appropriate 3D format content.
Auto: When a 3D identication signal is detected, the 3D format is selected automatically.
SBS: Display 3D signal in “Side-by-Side” format.
Top and Bottom: Display 3D signal in “Top and Bottom” format.
Frame Sequential: Display 3D signal in “Frame Sequential” format.
3D Sync Invert
Use this option to enable/disable the 3D sync invert function.
English
33
USING THE PROJECTOR
Display aspect ratio menu
Aspect Ratio
Select the aspect ratio of the displayed image between the following options:
4:3: This format is for 4:3 input sources.
16:9: This format is for 16:9 input sources, like HDTV and DVD enhanced for Wide screen TV.
16:10 (for WXGA and WUXGA models only): This format is for 16:10 input sources, like widescreen
laptops.
LBX (except SVGA and XGA models): This format is for non-16x9, letterbox source and if you use
external 16x9 lens to display 2.35:1 aspect ratio in full resolution.
Native: This format displays the original image without any scaling.
Auto: Automatically selects the appropriate display format.
Note:
Detailed informations about LBX mode:
± Some Letter-Box Format DVDs are not enhanced for 16x9 TVs. In this situation, the image
will not look right when displaying image in 16:9 mode. In this situation, please try to use the
4:3 mode to view the DVD. If the content is not 4:3, there will be black bars around the image
in 16:9 display. For this type of content, you can use LBX mode to ll the image on the 16:9
display.
± If you use an external anamorphic lens, this LBX mode also allows you to watch a 2.35:1
content (include Anamorphic DVD and HDTV lm source) that supports anamorphic wide is
enhanced for 16x9 Display in a wide 2.35:1 image. In this case, there are no black bars. Lamp
power and vertical resolution are fully utilized.
XGA scaling table:
Source 480i/p 576i/p 1080i/p 720p
4x3 Scale to 1024x768.
16x9 Scale to 1024x576.
Native No scaling will be made; the image is displayed with the resolution based on input source.
Auto -If source is 4:3, the screen type will be scaled to 1024x768.
-If source is 16:9, the screen type will be scaled to 1024x576.
-If source is 15:9, the screen type will be scaled to 1024x614.
-If source is 16:10, the screen type will be scaled to 1024x640.
34
English
USING THE PROJECTOR
XGA auto mapping rule:
Auto
4:3
Wide Laptop
SDTV
HDTV
WXGA scaling table (screen type 16x10):
Note:
Supported screen type 16:9 (1280x720), 16:10 (1280x800).
When screen type is 16:9, the 16x10 format becomes unavailable.
H-resolution V-resolution 1024 768
Input resolution Auto/Scale
640 480 1024 768
800 600 1024 768
1024 768 1024 768
1600 1200 1024 768
1280 720 1024 576
1280 768 1024 614
1280 800 1024 640
720 576 1024 576
720 480 1024 576
1280 720 1024 576
1920 1080 1024 576
When screen type is 16:10, the 16x9 format becomes unavailable.
If you select auto option then the display mode will be also automatically changed.
16 : 10 screen 480i/p 576i/p 1080i/p 720p PC
4x3 Scale to 1066x800.
16x10 Scale to 1280x800.
LBX Scale to 1280x960, then get the central 1280x800 image to display.
Native mode 1:1 mapping centered. 1:1 mapping
display
1280x800.
Auto -Input source will be t into 1280x800 display area and be kept its original aspect ratio.
-If source is 4:3, the screen type will be scaled to 1066x800.
-If source is 16:9, the screen type will be scaled to 1280x720.
-If source is 15:9, the screen type will be scaled to 1280x768.
-If source is 16:10, the screen type will be scaled to 1280x800.
1280x720
centered.
1:1 mapping
centered.
English
35
USING THE PROJECTOR
WXGA auto mapping rule (screen type 16x10):
Auto
4:3
Wide Laptop
SDTV
HDTV
WXGA scaling table (screen type 16x9):
16 : 9 screen 480i/p 576i/p 1080i/p 720p PC
4x3 Scale to 960x720.
16x9 Scale to 1280x720.
LBX Scale to 1280x960, then get the central 1280x720 image to display.
Native mode 1:1 mapping centered. 1:1 mapping
H-resolution V-resolution 1280 800
Input resolution Auto/Scale
640 480 1066 800
800 600 1066 800
1024 768 1066 800
1280 1024 1066 800
1400 1050 1066 800
1600 1200 1066 800
1280 720 1280 720
1280 768 1280 768
1280 800 1280 800
720 576 1280 720
720 480 1280 720
1280 720 1280 720
1920 1080 1280 720
display
1280x720.
1280x720
centered.
1:1 mapping
centred.
Auto -If this format is select, screen type will automatically become 16:9 (1280x720).
-If source is 4:3, the screen type will be scaled to 960x720.
-If source is 16:9, the screen type will be scaled to 1280x720.
-If source is 15:9, the screen type will be scaled to 1200x720.
-If source is 16:10, the screen type will be scaled to 1152x720.
36
English
USING THE PROJECTOR
WXGA auto mapping rule (screen type 16x9):
Auto
4:3
Wide Laptop
SDTV
HDTV
H-resolution V-resolution 1280 720
Input resolution Auto/Scale
640 480 960 720
800 600 960 720
1024 768 960 720
1280 1024 960 720
1400 1050 960 720
1600 1200 960 720
1280 720 1280 720
1280 768 1200 720
1280 800 1152 720
720 576 1280 720
720 480 1280 720
1280 720 1280 720
1920 1080 1280 720
Display edge mask menu
Edge Mask
Use this function to remove the video encoding noise on the edge of video source.
Display zoom menu
Zoom
Use to reduce or magnify an image on the projection screen.
Display image shift menu
Image Shift
Adjust the projected image position horizontally (H) or vertically (V).
Display geometric correction menu
Four Corner Adjustment
Allow the image to be squeezed to t an area dened by moving each of the four corners’ x and y position.
H Keystone
Adjust image distortion horizontally and make a squarer image. Horizontal keystone is used to correct a keystoned
image shape in which the left and right borders of the image are unequal in length. This is intended for use with
horizontally on-axis applications.
V Keystone
Adjust image distortion vertically and make a squarer image. Vertical keystone is used to correct a keystoned
image shape in which the top and bottom are slanted to one of the sides. This is intended when for use with
vertically on-axis applications.
Auto Keystone
Correct keystone digitally to t the projected image on the area on which you are projecting.
Reset
Resets the lamp hour counter after replacing the lamp.
English
37
USING THE PROJECTOR
Audio menu
Audio mute menu
Mute
Use this option to temporarily turn off the sound.
On: Choose the “On” to turn mute on.
Off: Choose the “Off” to turn mute off.
Note: “Mute” function affects both internal and external speaker volume.
Audio volume menu
Volume
Adjust the volume level.
Setup menu
Setup projection menu
Projection
Select the preferred projection between front, rear, ceiling-top, and rear-top.
Setup screen type menu
Screen Type (for WXGA and WUXGA models only)
Choose the screen type from 16:9 and 16:10.
Setup lamp settings menu
Lamp Reminder
Choose this function to show or to hide the warning message when the changing lamp message is displayed. The
message will appear 30 hours before suggested replacement of lamp.
Lamp Reset
Resets the lamp hour counter after replacing the lamp.
Setup lter settings menu
Optional Filter Installed
Set the warning message setting.
Yes: Display warning message after 500 hours of use.
Note: “Filter Usage Hours / Filter Reminder / Filter Reset” will only appear when “Optional Filter Installed” is “Yes”.
No: Turn off warning message.
Filter Usage Hours
Display the lter time.
English
38
USING THE PROJECTOR
Filter Reminder
Choose this function to show or hide the warning message when the changing lter message is displayed. The
available options include 300hr, 500hr, 800hr, and 1000hr.
Filter Reset
Reset the dust lter counter after replacing or cleaning the dust lter.
Setup power settings menu
Direct Power On
Choose “On” to activate Direct Power mode. The projector will automatically power on when AC power is supplied,
without pressing the “Power” key on the projector keypad or on the remote control.
Signal Power On
Choose “On” to activate Signal Power mode. The projector will automatically power on when a signal is detected,
without pressing the “Power” key on the projector Keypad or on the remote control.
Note: If the “Signal Power On” option is turned “On”, the power consumption of the projector in standby mode will
be over 3W.
Auto Power Off (min)
Sets the countdown timer interval. The countdown timer will start, when there is no signal being sent to the
projector. The projector will automatically power off when the countdown has nished (in minutes).
Sleep Timer (min)
Congure the sleep timer.
Sleep Timer (min): Sets the countdown timer interval. The countdown timer will start, with or without
a signal being sent to the projector. The projector will automatically power off when the countdown has
nished (in minutes).
Note: The Sleep Timer is reset every time when the projector is powered off.
Always On: Check to set the sleep timer always on.
Quick Resume
Set the quick resume setting.
On: If the projector is accidentally turned off, this feature allows the projector to be instantly powered
on again, if selected within a period of 100 seconds.
Off: The fan will start cooling the system after 10 seconds when user turns off the projector.
Power Mode (Standby)
Set the power mode for standby state.
Active: Choose “Active” to return to normal standby.
Eco: Choose “Eco.” to save power dissipation further < 0.5W.
USB Power (Standby)
Enable or disable USB power function during standby.
English
39
USING THE PROJECTOR
Setup security menu
Security
Enable this function to prompt for a password before using the projector.
On: Choose “On” to use security verication when the turning on the projector.
Off: Choose “Off” to be able to switch on the projector without password verication.
Security Timer
Can be select the time (Month/Day/Hour) function to set the number of hours the projector can be used. Once this
time has elapsed you will be requested to enter your password again.
Change Password
Use to set or modify the password that is prompted when turning the projector on.
Setup HDMI link settings menu
Note:
When you connect HDMI CEC-compatible devices to the projector with HDMI cables, you can control
them on the same power on or power off status using the HDMI Link control feature in the projector’s
OSD. This lets one device or multiple devices in a group power on or power off via HDMI Link Feature.
In a typical conguration, your DVD player may be connected to the projector through an amplier or
home theater system.
HDMI
Apmlier
HDMI Link
Enable/Disable the HDMI Link function. Support that power on control from player to projector and power off control
from projector to player.
HDMI
DVD Player
Setup test pattern menu
Test Pattern
Select the test pattern from green grid, magenta grid, white grid, white or disable this function (off).
Setup remote settings menu
IR Function
Set the IR function setting.
On: Choose “On”, the projector can be operated by the remote control from front or top IR receiver.
Off: Choose “Off”, the projector can’t be operated by the remote control from front or top IR receiver.
By selecting “Off”, you will be able to use the Keypad keys.
User1/ User2/ User3
Assign the default function for User1, User2, or User3 between HDMI 2, test pattern, LAN, brightness, contrast,
sleep timer, color matching, color temp, gamma, projection, lamp settings, zoom, freeze, and MHL.
English
40
USING THE PROJECTOR
Setup projector ID menu
Projector ID
ID denition can be set up by menu (range 0-99), and allow user control an individual projector by using RS232 command.
Setup options menu
Language
Select the multilingual OSD menu between English, German, French, Italian, Spanish, Portuguese, Polish, Dutch,
Swedish, Norwegian/Danish, Finnish, Greek, traditional Chinese, simplied Chinese, Japanese, Korean, Russian,
Hungarian, Czechoslovak, Arabic, Thai, Turkish, Farsi, Vietnamese, Indonesian, Romanian, and Slovakian.
Closed Captioning
Closed Captioning is a text version of the program sound or other information displayed on the screen. If the input
signal contains closed captions, you can turn on the feature and watch the channels. The available options include
“Off”, “CC1”, and “CC2”.
Menu Settings
Set the menu location on the screen and congure menu timer settings.
Menu Location: Select the menu location on the display screen.
Menu Timer: Set the duration where the OSD menu stays visible on the screen.
Auto Source
If set to “On”, the projector will automatically nd the available input source.
Input Source
Select the input source between HDMI1, HDMI2/MHL, VGA, Video, Network Display, USB Display, and Multimedia.
Input Name
Use to rename the input function for easier identication. The available options include HDMI1, HDMI2/MHL, VGA,
Video, Network Display, USB Display, and Multimedia.
High Altitude
When “On” is selected, the fans will spin faster. This feature is useful in high altitude areas where the air is thin.
Display Mode Lock
Choose “On” or “Off” to lock or unlock adjusting display mode settings.
Keypad Lock
When the keypad lock function is “On”, the Keypad will be locked. However, the projector can be operated by the
remote control. By selecting “Off”, you will be able to reuse the Keypad.
Information Hide
Enable this function to hide the information message.
Off: Choose “On” to hide the info message.
On: Choose “Off” to show the “searching” message.
Background Color
Use this function to display a blue, red, green, grey color, none, or logo screen when no signal is available.
English
41
USING THE PROJECTOR
Setup reset all menu
Reset OSD
Return the factory default settings for OSD menu settings.
Reset to Default
Return the factory default settings for all settings.
Network menu
Network WLAN menu
WLAN
Enable or disable WLAN function.
Network Status
Display the network connection status (read-only).
MAC Address
Display the MAC address (read-only).
IP Address
Display the IP address.
SSID (Service Set Identier)
Assign a network name for WLAN.
Connection Mode
Displays a connection mode.
Network LAN menu
Network Status
Display the network connection status (read-only).
MAC Address
Display the MAC address (read-only).
DHCP
Use this option to enable or disable the DHCP function.
On: Projector will obtain an IP address automatically from your network.
Off: To assign IP, subnet mask, gateway, and DNS conguration manually.
Note: Exiting OSD will automatically apply the entered values.
IP Address
Display the IP address.
Subnet Mask
Display subnet mask number.
Gateway
Display the default gateway of the network connected to the projector.
English
42
USING THE PROJECTOR
DNS
Display the DNS number.
Reset
Reset the network parameters.
How to use web browser to control your projector
1. Turn “On” the DHCP option on projector to allow a DHCP server to automatically assign an IP address.
2. Open the web browser in your PC and type in the projector’s IP address (“Network > LAN > IP
Address”).
3. Enter the user name and password, and click “Login”.
The projector’s conguration web interface opens.
Note:
The default user name and password is “admin”.
The steps in this section is based on Windows 7 operating system.
Making a direct connection from your computer to the projector*
1. Turn “Off” the DHCP option on the projector.
2. Congure the IP address, Subnet Mask, Gateway, and DNS on projector (“Network > LAN”).
3. Open Network and Sharing Center page on your PC, and assign the identical network parameters to
your PC as set on projector. Click “OK” to save the parameters.
4. Open the web browser on your PC and type in to the URL eld the IP address, assigned in step 3.
Then press “Enter” key.
Reset
Reset all values for LAN parameters.
Network control menu
Crestron
Use this function to select the network function (port: 41794).
For more information, please visit http://www.crestron.com and www.crestron.com/getroomview.
Extron
Use this function to select the network function (port: 2023).
English
43
USING THE PROJECTOR
PJ Link
Use this function to select the network function (port: 4352).
AMX Device Discovery
Use this function to select the network function (port: 9131).
Telnet
Use this function to select the network function (port: 23).
HTTP
Use this function to select the network function (port: 80).
Setup network control settings menu
LAN_RJ45 function
For simplicity and ease of operation, the projector provides diverse networking and remote management features.
The LAN / RJ45 function of the projector through a network, such as remotely manage: Power On / Off, brightness,
and contrast settings. Also, you can view the projector status information, such as: Video- Source, Sound-Mute, etc.
Projector
(Ethernet)
Wired LAN terminal functionalities
This projector can be controlled by using a PC (laptop) or other external device via LAN / RJ45 port and compatible
with Crestron / Extron / AMX (Device -Discovery) / PJLink.
Crestron is a registered trademark of Crestron Electronics, Inc. of the United States.
Extron is a registered trademark of Extron Electronics, Inc. of the United States.
AMX is a registered trademark of AMX LLC of the United States.
PJLink applied for trademark and logo registration in Japan, the United States of America, and other
countries by JBMIA.
The projector is supported by the specied commands of the Crestron Electronics controller and related software,
for example RoomView®.
http://www.crestron.com/
This projector is compliant to support Extron device(s) for reference.
http://www.extron.com/
This projector is supported by AMX ( Device Discovery ).
http://www.amx.com/
English
44
USING THE PROJECTOR
This projector supports all commands of PJLink Class1 (Version 1.00).
http://pjlink.jbmia.or.jp/english/
For more detailed information about the various types of external devices which can be connected to the LAN /
RJ45 port and remote control the projector, as well as the supported commands for these external devices, please
contact the Support-Service directly.
LAN RJ45
1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (laptop).
HDMI 1
USB
USB READER/DISPLAY
HDMI 2/MHL
VIDEO
VGA-IN/YPbPr VGA-OUT/YPbPr
RS-232C
AUDIO IN
RJ-45
AUDIO OUT
2. On the PC (Laptop), select Start > Control Panel > Network Connections.
3. Right-click on the Local Area Connection, and select Property.
4. In the Properties window, select the General tab, and select Internet Protocol (TCP / IP).
English
45
USING THE PROJECTOR
5. Click “Properties”.
6. Type in the IP address and Subnet mask, then press “OK”.
7. Press the “Menu” button on the projector.
8. Open on projector Network > LAN.
9. Enter the following connection parameters:
± DHCP: Off
± IP Address: 192.168.0.100
± Subnet Mask: 255.255.255.0
± Gateway: 192.168.0.254
± DNS: 192.168.0.1
10. Press “Enter” to conrm settings.
11. Open a web browser, for example Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher
installed.
12. In the Address bar, input the projector’s IP address: 192.168.0.100.
13. Press “Enter”.
46
English
USING THE PROJECTOR
The projector is setup for remote management. The LAN / RJ45 function displays as follows:
Information page
Main page
Tool page
Contact IT helpdesk
English
47
USING THE PROJECTOR
RS232 by Telnet Function
There is alternative RS232 command control way, in projector so called “RS232 by TELNET” for LAN / RJ45
interface.
Quick Start-Guide for “RS232 by Telnet”
Check and get the IP address on OSD of the projector.
Make sure that the PC / laptop can access the web-page of the projector.
Make sure that “Windows Firewall” setting is set disabled in case of “TELNET” function ltering out by
PC / laptop.
.
1. Select Start > All Programs.> Accessories > Command Prompt.
2. Input the command format as follows:
± telnet ttt.xxx.yyy.zzz 23 (“Enter” key pressed)
± (ttt.xxx.yyy.zzz: IP-Address of the projector)
3. If Telnet-Connection ready, and user can have RS232 command input, then “Enter” key pressed, the
RS232 command will be workable.
Specication for “RS232 by TELNET”:
1. Telnet: TCP.
2. Telnet port: 23 (for more detail, kindly please get contact with the service agent or team).
3. Telnet utility: Windows “TELNET.exe” (console mode).
4. Disconnection for RS232-by-Telnet control normally: Close
5. Windows Telnet utility directly after TELNET connection ready.
± Limitation 1 for Telnet-Control: there is less than 50 bytes for successive network payload for
Telnet-Control application.
48
± Limitation 2 for Telnet-Control: there is less than 26 bytes for one complete RS232 command for
Telnet-Control.
± Limitation 3 for Telnet-Control: Minimum delay for next RS232 command must be more than 200 (ms).
English
USING THE PROJECTOR
Info menu
Info menu
View the projector information as listed below:
Regulatory
Serial Number
Source
Resolution
Refresh Rate
Display Mode
Network Status
Power mode(standby)
Lamp Hours
Network Status
IP Address
Projector ID
Filter Usage Hours
Brightness Mode
FW Version
English
49
MAINTENANCE
Replacing the lamp
The projector automatically detects the lamp life. When the lamp life is nearing the end of use, a warning message
will appear on the screen.
Warning
Lamp Warning
Lamp life exceeded.
When you see this message, please contact your local reseller or service center to change the lamp as soon as
possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp.
Warning: If ceiling mounted, please use caution when opening the lamp access panel. It is
recommended to wear safety glasses if changing the bulb when ceiling mounted. Caution must be used
to prevent any loose parts from falling out of projector.
Warning: Lamp compartment is hot! Allow it to cool down before changing lamp!
Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The
bulb may shatter and cause injury if it is dropped.
50
English
MAINTENANCE
Replacing the lamp (continued)
5
2
3
4
6
1
Procedure:
1. Switch off the power to the projector by pressing the " " button on the remote control or the projector
keypad.
2. Allow the projector to cool down for at least 30 minutes.
3. Disconnect the power cord.
4. Unscrew the screw on the cover. 1
5. Remove the cover. 2
6. Unscrew the screw on the lamp module. 3
7. Lift up the lamp handle. 4
8. Remove the lamp cord. 5
9. Remove the lamp module carefully. 6
10. To replace the lamp module, reverse the previous steps.
11. Turn on the projector and reset the lamp timer.
12. Lamp Reset: (i) Press "Menu" (ii) Select "Setup" (iii) Select "Lamp Settings" (iv) Select "Lamp
Reset" (v) Select "Yes".
Note:
The screw on the lamp cover and the lamp cannot be removed.
The projector cannot be turned on if the lamp cover has not been placed back on the projector.
Do not touch the glass area of the lamp. Hand oil can cause the lamp shatter. Use a dry cloth to clean
the lamp module if it was accidentally touched.
English
51
MAINTENANCE
Installing and cleaning the dust lter
Installing the dust lter
Note: Dust lters are only required/supplied in the selected regions with excessive dust.
Cleaning the dust lter
We recommend you to clean the dust lter every three months. Clean it more often if the projector is used in a
dusty environment.
Procedure:
1. Switch off the power to the projector by pressing the " " button on the remote control or the projector
keypad.
2. Disconnect the power cord.
3. Remove the dust lter carefully. 1
4. Clean or replace the dust lter. 2
5. To install the dust lter, reverse the previous steps.
2
52
1
English
ADDITIONAL INFORMATION
Compatible resolutions
Digital compatibility
B0/Established
Timing
720x400 @ 70Hz SVGA: Native timing: 640x80p @ 60Hz 720x480p @ 60Hz
640x480 @ 60Hz 800x600 @ 120Hz XGA: 1024x768 @ 60Hz 720x480p @ 60Hz 1280x720p @ 60Hz
640x480 @ 67Hz 1024x768 @ 120Hz WXGA: 1280x800 @ 60Hz;
640x480 @ 72Hz 1280x800 @ 60Hz 1080P: 1920x1080 @ 60Hz 1920x1080i @ 60Hz 1920x1080i @ 50Hz
640x480 @ 75Hz 1280x1024 @ 60Hz 720(1440)x480i @ 60Hz 1920x1080p @ 60Hz
800x600 @ 56Hz 1680x1050 @ 60Hz 1920x1080p @ 60Hz
800x600 @ 60Hz 1280x720 @ 60Hz 720x576p @ 50Hz
800x600 @ 72Hz 1280x720 @ 120Hz 1280x720p @ 50Hz
800x600 @ 75Hz 1600x1200 @ 60Hz 1920x1080i @ 50Hz
832x624 @ 75Hz XGA/WXGA: 720(1440)x576i @ 50Hz
1024x768 @ 60Hz 1440x900 @ 60Hz 1920x1080p @ 50Hz
1024x768 @ 70Hz 1024x768 @ 120Hz 1920x1080p @ 24Hz
1024x768 @ 75Hz 1280x800 @ 60Hz 1920x1080p @ 30Hz
1280x1024 @ 75Hz 1280x1024 @ 60Hz
1152x870 @ 75Hz 1680x1050 @ 60Hz
B0/Standard Timing B0/Detail Timing B1/Video Mode B1/Detail Timing
1280x720p @ 60Hz 1366x768 @ 60Hz
1280x720 @ 60Hz
1280x720 @ 60Hz
1280x720 @ 120Hz
1600x1200 @ 60Hz
1080P:
1280x720 @ 60Hz
1280x800 @ 60Hz
1280x1024 @ 60Hz
1400x1050 @ 60Hz
1600x1200 @ 60Hz
1440x900 @ 60Hz
1280x720 @ 120Hz
1024x768 @ 120Hz
Analog compatibility
B0/Established
Timing
720x400 @ 70Hz SVGA: Native timing: 1366x768 @ 60Hz
640x480 @ 60Hz 800x600 @ 120Hz XGA: 1024x768 @ 60Hz
640x480 @ 67Hz 1024x768 @ 120Hz WXGA: 1280x800 @ 60Hz;
640x480 @ 72Hz 1280x800 @ 60Hz 1080P: 1920x1080 @ 60Hz
640x480 @ 75Hz 1280x1024 @ 60Hz
800x600 @ 56Hz 1680x1050 @ 60Hz
800x600 @ 60Hz 1280x720 @ 60Hz
800x600 @ 72Hz 1280x720 @ 120Hz
800x600 @ 75Hz 1600x1200 @ 60Hz
832x624 @ 75Hz XGA/WXGA:
1024x768 @ 60Hz 1440x900 @ 60Hz
B0/Standard Timing B0/Detail Timing B1/Video Mode B1/Detail Timing
1280x720 @ 60Hz
English
53
ADDITIONAL INFORMATION
B0/Established
Timing
1024x768 @ 70Hz 1024x768 @ 120Hz
1024x768 @ 75Hz 1280x800 @ 60Hz
1280x1024 @ 75Hz 1280x1024 @ 60Hz
1152x870 @ 75Hz 1680x1050 @ 60Hz
B0/Standard Timing B0/Detail Timing B1/Video Mode B1/Detail Timing
1280x720 @ 60Hz
1280x720 @ 120Hz
1600x1200 @ 60Hz
1080P:
1280x720 @ 60Hz
1280x800 @ 60Hz
1280x1024 @ 60Hz
1400x1050 @ 60Hz
1600x1200 @ 60Hz
1440x900 @ 60Hz
1280x720 @ 120Hz
1024x768 @ 120Hz
True 3D video compatibility
HDMI 1.4a 3D
Input
Input resolutions
HDMI 1.3
Input timing
1280x720P @ 50Hz Top - and - Bottom
1280x720P @ 60Hz Top - and - Bottom
1280x720P @ 50Hz Frame packing
1280x720P @ 60Hz Frame packing
1920x1080i @ 50 Hz Side- by-Side (Half)
1920x1080i @ 60 Hz Side- by-Side (Half)
1920x1080P @ 24 Hz Top - and- Bottom
1920x1080P @ 24 Hz Frame packing
1920x1080i @ 50Hz
1920x1080i @ 60Hz
1280x720P @ 50Hz
1280x720P @ 60Hz
800 x 600 @ 60Hz
1024 x 768 @ 60Hz
1280 x 800 @ 60Hz
1920x1080i @ 50Hz
1920x1080i @ 60Hz
1280x720P @ 50Hz
1280x720P @ 60Hz
800x600 @ 60Hz
1024x768 @ 60Hz
1280x800 @ 60Hz
480i HQFS 3D format is Frame sequential
Side-by-Side(Half) SBS mode is on
Top-and-Bottom TAB mode is on
54
Note:
If 3D input is 1080p@24hz, the DMD should replay with integral multiple with 3D mode.
Support NVIDIA 3DTV Play if there is no patent fee from Optoma. 1080i@25hz and 720p@50hz will
run in 100 hz; other 3D timing will run in 120hz.
1080p@24hz will run in 144Hz.
English
ADDITIONAL INFORMATION
Image size and projection distance
(W365)
Diagonal
length
(inch)
Screen Size W x H Projection Distance (D)
(m) (inch) (m) (inch)
Offset (HD)
size of
16:9
Width Height Width Height Wide Tele Wide Tele (m) (inch)
Screen
30 0.64 0.40 25.27 15.79 - 1.10 - 3.61 0.05 0.16
40 0.86 0.54 33.92 21.20 1.34 1.48 4.41 4.85 0.07 0.22
60 1.29 0.81 50.88 31.80 2.02 2.22 6.61 7.27 0.10 0.33
70 1.51 0.94 59.36 37.10 2.35 2.59 7.71 8.48 0.12 0.38
80 1.72 1.08 67.84 42.40 2.69 2.96 8.81 9.70 0.13 0.44
90 1.94 1.21 76.32 47.70 3.02 3.33 9.92 10.91 0.15 0.49
100 2.15 1.35 84.80 53.00 3.36 3.70 11.02 12.12 0.17 0.55
120 2.58 1.62 101.76 63.60 4.03 4.44 13.22 14.54 0.20 0.66
150 3.23 2.02 127.20 79.50 5.04 5.54 16.53 18.18 0.25 0.82
180 3.88 2.42 152.64 95.40 6.05 6.65 19.83 21.82 0.30 0.99
200 4.31 2.69 169.60 106.00 6.72 7.39 22.04 24.24 0.33 1.09
250 5.38 3.37 212.00 132.50 8.40 9.24 27.54 30.30 0.42 1.37
300.6 6.47 4.05 254.91 159.32 10.10 - 33.12 - 0.50 1.65
Note: Zoom ratio is 1:1.1x.
(X365)
Diagonal
length
(inch)
size of
16:9
Width Height Width Height Wide Tele Wide Tele (m) (inch)
Screen
27 0.56 0.42 21.87 16.40 - 1.20 - 3.93 0.06 2.46
40 0.81 0.61 32.00 24.00 1.58 1.76 5.17 5.76 0.09 3.60
50 1.02 0.76 40.00 30.00 1.97 2.19 6.46 7.20 0.11 4.50
60 1.22 0.91 48.00 36.00 2.37 2.63 7.76 8.64 0.14 5.40
70 1.42 1.07 56.00 42.00 2.76 3.07 9.05 10.07 0.16 6.30
80 1.63 1.22 64.00 48.00 3.15 3.51 10.34 11.51 0.18 7.20
90 1.83 1.37 72.00 54.00 3.55 3.95 11.63 12.95 0.21 8.10
100 2.03 1.52 80.00 60.00 3.94 4.39 12.93 14.39 0.23 9.00
120 2.44 1.83 96.00 72.00 4.73 5.27 15.51 17.27 0.27 10.80
150 3.05 2.29 120.00 90.00 5.91 6.58 19.39 21.59 0.34 13.50
180 3.66 2.74 144.00 108.00 7.10 7.90 23.27 25.91 0.41 16.20
200 4.06 3.05 160.00 120.00 7.88 8.78 25.85 28.78 0.46 18.00
250 5.08 3.81 200.00 150.00 9.86 10.97 32.32 35.98 0.57 22.50
304.5 6.19 4.64 243.60 182.70 12.00 - 39.36 - 0.70 27.41
Screen Size W x H Projection Distance (D)
(m) (inch) (m) (inch)
Offset (HD)
Note: Zoom ratio is 1:1.1x.
English
55
ADDITIONAL INFORMATION
(S365)
Diagonal
length
(inch)
Screen Size W x H Projection Distance (D)
(m) (inch) (m) (inch)
Offset (HD)
size of
16:9
Width Height Width Height Wide Tele Wide Tele (m) (inch)
Screen
27 0.55 0.41 21.60 16.20 - 1.19 - 3.89 0.06 0.20
40 0.81 0.61 32.00 24.00 1.58 1.76 5.17 5.76 0.09 0.30
50 1.02 0.76 40.00 30.00 1.97 2.19 6.46 7.20 0.11 0.37
60 1.22 0.91 48.00 36.00 2.37 2.63 7.76 8.64 0.14 0.45
70 1.42 1.07 56.00 42.00 2.76 3.07 9.05 10.07 0.16 0.52
80 1.63 1.22 64.00 48.00 3.15 3.51 10.34 11.51 0.18 0.60
90 1.83 1.37 72.00 54.00 3.55 3.95 11.63 12.95 0.21 0.67
100 2.03 1.52 80.00 60.00 3.94 4.39 12.93 14.39 0.23 0.75
120 2.44 1.83 96.00 72.00 4.73 5.27 15.51 17.27 0.27 0.90
150 3.05 2.29 120.00 90.00 5.91 6.58 19.39 21.59 0.34 1.12
180 3.66 2.74 144.00 108.00 7.10 7.90 23.27 25.91 0.41 1.35
200 4.06 3.05 160.00 120.00 7.88 8.78 25.85 28.78 0.46 1.50
250 5.08 3.81 200.00 150.00 9.86 10.97 32.32 35.98 0.57 1.87
304.5 6.19 4.64 243.60 182.70 12.00 - 39.36 - 0.70 2.28
Note: Zoom ratio is 1:1.1x.
Top View
Side View
Projection Distance (D)
Projection Distance (D)
Screen
Screen
Screen (W)
Screen (H)
Offset (Hd)
Diagonal
Height
Width
56
English
ADDITIONAL INFORMATION
Projector dimensions and ceiling mount installation
1. To prevent damage to your projector, please use the Optoma ceiling mount.
2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to
the projector meet the following specications:
Screw type: M4*3
Minimum screw length: 10mm
Lens
96.37
82.87
297.99
110.00
55.00
82.30 90.10
Unit: mm
Note: Please note that damage resulting from incorrect installation will void the warranty.
Warning:
If you buy a ceiling mount from another company, please be sure to use the correct screw size.
Screw size will vary depending on the thickness of the mounting plate.
Be sure to keep at least 10 cm gap between the ceiling and the bottom of the projector.
Avoid installing the projector near a heat source.
English
57
ADDITIONAL INFORMATION
RS232 protocol function list
Baud Rate : 9600
Data Bits: 8
Parity: None
Stop Bits: 1
Flow Control : None
UART16550 FIFO: Disable
Projector Return (Pass): P
Projector Return (Fail): F XX=01-99, projector's ID, XX=00 is for all projectors
Note: There is a <CR> after all ASCII commands 0D is the HEX code for <CR> in ASCII code.
SEND to projector
232 ASCII
Code
~XX00 1 7E 30 30 30 30 20 31 0D Power ON
~XX00 0 7E 30 30 30 30 20 30 0D Power OFF (0/2 for backward compatible)
~XX00 1
~nnnn
~XX01 1 7E 30 30 30 31 20 31 0D Resync
~XX02 1 7E 30 30 30 32 20 31 0D AV Mute On
~XX02 0 7E 30 30 30 32 20 30 0D Off (0/2 for backward compatible)
~XX03 1 7E 30 30 30 33 20 31 0D Mute On
~XX03 0 7E 30 30 30 33 20 30 0D Off (0/2 for backward compatible)
~XX04 1 7E 30 30 30 34 20 31 0D Freeze
~XX04 0 7E 30 30 30 34 20 30 0D Unfreeze (0/2 for backward compatible)
~XX05 1 7E 30 30 30 35 20 31 0D Zoom Plus
~XX06 1 7E 30 30 30 36 20 31 0D Zoom Minus
~XX12 1 7E 30 30 31 32 20 31 0D Direct Source Commands HDMI
~XX12 15 7E 30 30 31 32 20 31 35 0D Direct Source Commands HDMI 2
~XX12 5 7E 30 30 31 32 20 35 0D VGA
~XX12 10 7E 30 30 31 32 20 31 30 0D Video
~XX12 18 7E 30 30 31 32 20 31 38 0D Network Display(Presenter)
~XX12 19 7E 30 30 31 32 20 31 39 0D USB display
~XX12 23 7E 30 30 31 32 20 32 33 0D Multimedia
~XX20 1 7E 30 30 32 30 20 31 0D Display Mode Presentation
~XX20 2 7E 30 30 32 30 20 32 0D Bright
~XX20 3 7E 30 30 32 30 20 33 0D Cinema
~XX20 12 7E 30 30 32 30 20 31 32 0D Display Mode Game
~XX20 4 7E 30 30 32 30 20 34 0D sRGB
~XX20 13 7E 30 30 32 30 20 31 33 0D Display Mode DICOM SIM.
~XX20 5 7E 30 30 32 30 20 35 0D User
~XX20 9 7E 30 30 32 30 20 39 0D 3D
~XX506 0 & 2 7E 30 30 35 30 36 20 30 0D Wall Colorlens Off
~XX506 1 7E 30 30 35 30 36 20 31 0D Wall Color Blackboard
~XX506 7 7E 30 30 35 30 36 20 37 0D Wall Color Light Yellow
~XX506 3 7E 30 30 35 30 36 20 33 0D Wall Color Light Green
~XX506 4 7E 30 30 35 30 36 20 34 0D Wall Color Light Blue
~XX506 5 7E 30 30 35 30 36 20 35 0D Wall Color Pink
~XX506 6 7E 30 30 35 30 36 20 36 0D Wall Color Gray
~XX21 n 7E 30 30 32 31 20 a 0D Brightness n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX22 n 7E 30 30 32 32 20 a 0D Contrast n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX23 n 7E 30 30 32 33 20 a 0D Sharpness n = 1 (a=31) ~ 15 (a=31 35)
~XX45 n 7E 30 30 34 34 20 a 0D Color (Saturation) n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX44 n 7E 30 30 34 35 20 a 0D Tint n = -50 (a=2D 35 30) ~ 50 (a=35 30))
~XX35 1 7E 30 30 33 35 20 31 0D Gamma Film
~XX35 2 7E 30 30 33 35 20 32 0D Gamma Video
~XX35 3 7E 30 30 33 35 20 33 0D Gamma Graphics
~XX35 4 7E 30 30 33 35 20 34 0D Gamma Standard
~XX35 5 7E 30 30 33 35 20 35 0D Gamma 1.8
~XX35 6 7E 30 30 33 35 20 36 0D Gamma 2
~XX35 12 7E 30 30 33 35 20 31 31 0D Gamma 2.4
~XX34 n 7E 30 30 33 34 20 a 0D BrilliantColor
HEX Code Function Description
7E 30 30 30 30 20 31 20 a 0D Power ON with Password ~nnnn = ~0000 (a=7E 30 30 30 30)
TM
~9999 (a=7E 39 39 39 39)
n = 1 (a=30) ~ 10 (a=31 30)
58
English
ADDITIONAL INFORMATION
SEND to projector
232 ASCII
Code
~XX36 4 7E 30 30 33 36 20 34 0D Color Temp. Warm
~XX36 1 7E 30 30 33 36 20 31 0D Color Temp. Medium
~XX36 2 7E 30 30 33 36 20 32 0D Color Temp. Cool
~XX327 n 7E 30 30 33 32 37 20 a 0D Color Matching Red Hue n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX328 n 7E 30 30 33 32 38 20 a 0D Color Matching Green Hue n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX329 n 7E 30 30 33 32 39 20 a 0D Color Matching Blue Hue n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX330 n 7E 30 30 33 33 30 20 a 0D Color Matching Cyan Hue n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX331 n 7E 30 30 33 33 31 20 a 0D Color Matching Yellow Hue n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX332 n 7E 30 30 33 33 32 20 a 0D Color Matching Magenta Hue n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX333 n 7E 30 30 33 33 33 20 a 0D Color Matching Red Stutation n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX334 n 7E 30 30 33 33 34 20 a 0D Color Matching Green Stutation n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX335 n 7E 30 30 33 33 35 20 a 0D Color Matching Blue Stutation n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX336 n 7E 30 30 33 33 36 20 a 0D Color Matching Cyan Stutation n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX337 n 7E 30 30 33 33 37 20 a 0D Color Matching Yellow Stutation n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX338 n 7E 30 30 33 33 38 20 a 0D Color Matching Magenta Stutation n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX339 n 7E 30 30 33 33 39 20 a 0D Color Matching Red Gain n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX340 n 7E 30 30 33 34 30 20 a 0D Color Matching Green Gain n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX341 n 7E 30 30 33 34 31 20 a 0D Color Matching Blue Gain n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX342 n 7E 30 30 33 34 32 20 a 0D Color Matching Cyan Gain n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX343 n 7E 30 30 33 34 33 20 a 0D Color Matching Yellow Gain n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX344 n 7E 30 30 33 34 34 20 a 0D Color Matching Magenta Gain n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX345 n 7E 30 30 33 34 35 20 a 0D Color Matching White /R n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX346 n 7E 30 30 33 34 36 20 a 0D Color Matching White /G n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX347 n 7E 30 30 33 34 37 20 a 0D Color Matching White /B n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX215 1 7E 30 30 32 31 35 20 31 0D Color Matching Reset
~XX24 n 7E 30 30 32 34 20 a 0D RGB Gain/Bias Red Gain n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX25 n 7E 30 30 32 35 20 a 0D RGB Gain/Bias Green Gain n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX26 n 7E 30 30 32 36 20 a 0D RGB Gain/Bias Blue Gain n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX27 n 7E 30 30 32 37 20 a 0D RGB Gain/Bias Red Bias n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX28 n 7E 30 30 32 38 20 a 0D RGB Gain/Bias Green Bias n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX29 n 7E 30 30 32 39 20 a 0D RGB Gain/Bias Blue Bias n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX517 1 7E 30 30 35 31 37 20 31 0D RGB Gain/Bias Reset Reset
~XX37 1 7E 30 30 33 37 20 31 0D Color Space Auto
~XX37 2 7E 30 30 33 37 20 32 0D RGB\ RGB(0-255)
~XX37 3 7E 30 30 33 37 20 33 0D YUV
~XX37 4 7E 30 30 33 37 20 34 0D RGB(16 - 235)
~XX200 n 7E 30 30 32 30 30 20 a 0D White level n = 0 (a=30) ~ 31 (a=33 31)
~XX201 n 7E 30 30 32 30 31 20 a 0D Black level n = -5 (a=2D 35) ~ 5 (a=35)
~XX204 1 7E 30 30 32 30 34 20 31 0D 0 IRE
~XX204 0 7E 30 30 32 30 34 20 30 0D 7.5 IRE
~XX91 1 7E 30 30 39 31 20 31 0D Signal Automatic On
~XX91 0 7E 30 30 39 31 20 30 0D Signal Automatic Off
~XX73 n 7E 30 30 37 33 20 a 0D Signal Frequency n = -5 (a=2D 35) ~ 5 (a=35) By signal
~XX74 n 7E 30 30 37 34 20 a 0D Signal Phase n = 0 (a=30) ~ 63 (a=36 33) By signal
~XX75 n 7E 30 30 37 35 20 a 0D Signal H. Position n = -5 (a=2D 35) ~ 5 (a=35) By timing
~XX76 n 7E 30 30 37 36 20 a 0D Signal V. Position n = -5 (a=2D 35) ~ 5 (a=35) By timing
~XX110 1 7E 30 30 31 31 30 20 31 0D Brightness Mode Bright
~XX110 2 7E 30 30 31 31 30 20 32 0D Eco
~XX110 3 7E 30 30 31 31 30 20 33 0D Eco+
~XX110 4 7E 30 30 31 31 30 20 34 0D Dynamic
~XX509 1 7E 30 30 35 30 39 20 31 0D Image Settings Reset n=1 Reset
~XX230 0 7E 30 30 32 33 30 20 30 0D 3D Mode OFF
~XX230 1 7E 30 30 32 33 30 20 31 0D 3D Mode DLP-Link
~XX230 3 7E 30 30 32 33 30 20 33 0D 3D Mode IR
~XX400 0 7E 30 30 34 30 30 20 30 0D 3D->2D 3D
~XX400 1 7E 30 30 34 30 30 20 31 0D L
~XX400 2 7E 30 30 34 30 30 20 32 0D R
~XX405 0 7E 30 30 34 30 35 20 30 0D 3D Format Auto
HEX Code Function Description
English
59
ADDITIONAL INFORMATION
SEND to projector
232 ASCII
Code
~XX405 1 7E 30 30 34 30 35 20 31 0D SBS
~XX405 2 7E 30 30 34 30 35 20 32 0D Top and Bottom
~XX405 3 7E 30 30 34 30 35 20 33 0D Frame sequential
~XX231 0 7E 30 30 32 33 31 20 30 0D 3D Sync Invert Off
~XX231 1 7E 30 30 32 33 31 20 31 0D 3D Sync Invert On
~XX60 1 7E 30 30 36 30 20 31 0D Aspect Ratio 4:3
~XX60 2 7E 30 30 36 30 20 32 0D 16:9
~XX60 3 7E 30 30 36 30 20 33 0D 16:10(WXGA/ WUXGA)
~XX60 5 7E 30 30 36 30 20 35 0D LBX [except for SVGA XGA models]
~XX60 6 7E 30 30 36 30 20 36 0D Native
~XX60 7 7E 30 30 36 30 20 37 0D Auto
~XX61 n 7E 30 30 36 31 20 a 0D Edge mask n = 0 (a=30) ~ 10 (a=31 30)
~XX62 n 7E 30 30 36 32 20 a 0D Zoom n = -5 (a=2D 35) ~ 25 (a=32 35)
~XX63 n 7E 30 30 36 33 20 a 0D H Image Shift n = -100 (a=2D 31 30 30) ~ 100 (a=31 30 30)
~XX64 n 7E 30 30 36 34 20 a 0D V Image Shift n = -100 (a=2D 31 30 30) ~ 100 (a=31 30 30)
~XX66 n 7E 30 30 36 36 20 a 0D V Keystone n = -20 (a=2D 32 30) ~ 20 (a=32 30)
~XX65 n 7E 30 30 36 35 20 a 0D H Keystone n = -20 (a=2D 32 30) ~ 20 (a=32 30)
~XX69 1 7E 30 30 36 39 20 31 0D Auto Keystone On
~XX69 0 7E 30 30 36 39 20 30 0D Auto Keystone Off
~XX59 1 7E 30 30 35 39 20 31 0D Four corners (Top-Left) Right+
~XX59 2 7E 30 30 35 39 20 32 0D Left+
~XX59 3 7E 30 30 35 39 20 33 0D Up+
~XX59 4 7E 30 30 35 39 20 34 0D Down+
~XX59 5 7E 30 30 35 39 20 35 0D (Top-Right) Right+
~XX59 6 7E 30 30 35 39 20 36 0D Left+
~XX59 7 7E 30 30 35 39 20 37 0D Up+
~XX59 8 7E 30 30 35 39 20 38 0D Down+
~XX59 9 7E 30 30 35 39 20 39 0D (Bottom-Left) Right+
~XX59 10 7E 30 30 35 39 20 31 30 0D Left+
~XX59 11 7E 30 30 35 39 20 31 31 0D Up+
~XX59 12 7E 30 30 35 39 20 31 32 0D Down+
~XX59 13 7E 30 30 35 39 20 31 33 0D (Bottom-Right) Right+
~XX59 14 7E 30 30 35 39 20 31 34 0D Left+
~XX59 15 7E 30 30 35 39 20 31 35 0D Up+
~XX59 16 7E 30 30 35 39 20 31 36 0D Down+
~XX516 7E 30 30 35 31 36 20 0D Four corners reset Reset
~XX71 1 7E 30 30 37 31 20 31 0D Projection Front-Desktop
~XX71 2 7E 30 30 37 31 20 32 0D Rear-Desktop
~XX71 3 7E 30 30 37 31 20 33 0D Front-Ceiling
~XX71 4 7E 30 30 37 31 20 34 0D Rear-Ceiling
(WXGA/ WUXGA only)
~XX90 1 7E 30 30 39 31 20 31 0D Screen Type 16:10
~XX90 0 7E 30 30 39 31 20 30 0D 16:9
~XX109 1 7E 30 30 31 30 39 20 31 0D Lamp Reminder On
~XX109 0 7E 30 30 31 30 39 20 30 0D Off (0/2 for backward compatible)
~XX111 1 7E 30 30 31 31 31 20 31 0D Lamp Reset Ye s
~XX320 1 7E 30 30 33 32 30 20 31 0D Optional Filter Installed Yes
~XX320 0 7E 30 30 33 32 30 20 30 0D No (0/2 for backward compatible)
~XX322 0 7E 30 30 33 32 32 20 30 0D Filter Reminder Off
~XX322 1 7E 30 30 33 32 32 20 31 0D Filter Reminder 300 hr
~XX322 2 7E 30 30 33 32 32 20 32 0D Filter Reminder 500 hr
~XX322 3 7E 30 30 33 32 32 20 33 0D Filter Reminder 800 hr
~XX322 4 7E 30 30 33 32 32 20 34 0D Filter Reminder 1000 hr
~XX323 1 7E 30 30 33 32 33 20 31 0D Filter Reset Yes
~XX105 1 7E 30 30 31 30 35 20 31 0D Direct Power On On
~XX105 0 7E 30 30 31 30 35 20 30 0D Direct Power On Off (0/2 for backward compatible)
~XX113 1 7E 30 30 31 31 33 20 31 0D Signal Power On On
~XX113 0 7E 30 30 31 31 33 20 30 0D Signal Power On Off (0/2 for backward compatible)
HEX Code Function Description
60
English
ADDITIONAL INFORMATION
SEND to projector
232 ASCII
Code
~XX106 n 7E 30 30 31 30 36 20 a 0D Auto Power Off (min) “n = 0 (a=30) ~ 180 (a=31 38 30)
~XX107 n 7E 30 30 31 30 37 20 a 0D Sleep Timer (min) “n = 0 (a=30) ~ 990 (a=39 39 30)
~XX507 0 7E 30 30 35 30 37 20 30 0D Sleep Timer Repeat Off (0/2 for backward compatible)
~XX507 1 7E 30 30 35 30 37 20 31 0D Sleep Timer Repeat On
~XX115 1 7E 30 30 31 31 35 20 31 0D Quick Resume On
~XX115 0 7E 30 30 31 31 35 20 30 0D Quick Resume Off (0/2 for backward compatible)
~XX114 1 7E 30 30 31 31 34 20 31 0D Power Mode ( Standby) Active
~XX114 0 7E 30 30 31 31 34 20 30 0D Power Mode ( Standby) Eco. (<0.5W)
~XX77 n 7E 30 30 37 37 20 aabbcc 0D Security Security Timer Month/Day/Hour n = mm/dd/hh
~XX78 1
~nnnn
~XX78 0
~nnnn
~XX511 0 7E 30 30 35 31 31 20 30 0D HDMI Link n=0 & 2 Off
~XX511 1 7E 30 30 35 31 31 20 31 0D HDMI Link n=1 On
~XX195 0 7E 30 30 31 39 35 20 30 0D Test Pattern Off
~XX195 1 7E 30 30 31 39 35 20 31 0D Test Pattern Grid (White)
~XX195 2 7E 30 30 31 39 35 20 32 0D Test Pattern White
~XX195 3 7E 30 30 31 39 35 20 33 0D Test Pattern Grid(Green)
~XX195 4 7E 30 30 31 39 35 20 34 0D Test Pattern Grid (Magenta)
~XX11 0 7E 30 30 31 31 20 30 0D IR Function Off
~XX11 1 7E 30 30 31 31 20 31 0D On
~XX79 n 7E 30 30 37 39 20 a 0D Projector ID n = 00 (a=30 30) ~ 99 (a=39 39)
~XX70 1 7E 30 30 37 30 20 31 0D Language English
~XX70 2 7E 30 30 37 30 20 32 0D German
~XX70 3 7E 30 30 37 30 20 33 0D French
~XX70 4 7E 30 30 37 30 20 34 0D Italian
~XX70 5 7E 30 30 37 30 20 35 0D Spanish
~XX70 6 7E 30 30 37 30 20 36 0D Portuguese
~XX70 7 7E 30 30 37 30 20 37 0D Polish
~XX70 8 7E 30 30 37 30 20 38 0D Dutch
~XX70 9 7E 30 30 37 30 20 39 0D Swedish
~XX70 10 7E 30 30 37 30 20 31 30 0D Norwegian/Danish
~XX70 11 7E 30 30 37 30 20 31 31 0D Finnish
~XX70 12 7E 30 30 37 30 20 31 32 0D Greek
~XX70 13 7E 30 30 37 30 20 31 33 0D Traditional Chinese
~XX70 14 7E 30 30 37 30 20 31 34 0D Simplied Chinese
~XX70 15 7E 30 30 37 30 20 31 35 0D Japanese
~XX70 16 7E 30 30 37 30 20 31 36 0D Korean
~XX70 17 7E 30 30 37 30 20 31 37 0D Russian
~XX70 18 7E 30 30 37 30 20 31 38 0D Hungarian
~XX70 19 7E 30 30 37 30 20 31 39 0D Czechoslovak
~XX70 20 7E 30 30 37 30 20 32 30 0D Arabic
~XX70 21 7E 30 30 37 30 20 32 31 0D Thai
~XX70 22 7E 30 30 37 30 20 32 32 0D Turkish
~XX70 23 7E 30 30 37 30 20 32 33 0D Farsi
~XX70 25 7E 30 30 37 30 20 32 35 0D Vietnamese
~XX70 26 7E 30 30 37 30 20 32 36 0D Indonesian
~XX70 27 7E 30 30 37 30 20 32 37 0D Romanian
~XX70 28 7E 30 30 37 30 20 32 38 0D Slovakian
~XX88 0 7E 30 30 38 38 20 30 0D Closed Captioning Off
~XX88 1 7E 30 30 38 38 20 31 0D cc1
~XX88 2 7E 30 30 38 38 20 32 0D cc2
HEX Code Function Description
(5 minutes for each step).”
(30 minutes for each step).”
mm= 00 (aa=30 30) ~ 12 (aa=31 32)
dd = 00 (bb=30 30) ~ 30 (bb=33 30)
hh= 00 (cc=30 30) ~ 24 (cc=32 34)
7E 30 30 37 38 20 31 0D Security On
7E 30 30 37 38 20 32 20 a 0D Off(0/2 for backward compatible)
~nnnn = ~0000 (a=7E 30 30 30 30)
~9999 (a=7E 39 39 39 39)
English
61
ADDITIONAL INFORMATION
SEND to projector
232 ASCII
Code
~XX72 1 7E 30 30 37 32 20 31 0D Menu Location Top Left
~XX72 2 7E 30 30 37 32 20 32 0D Top Right
~XX72 3 7E 30 30 37 32 20 33 0D Centre
~XX72 4 7E 30 30 37 32 20 34 0D Bottom Left
~XX72 5 7E 30 30 37 32 20 35 0D Bottom Right
~XX515 0 7E 30 30 35 31 35 20 30 0D Menu Timer n=0 & 2 Off
~XX515 1 7E 30 30 35 31 35 20 31 0D Menu Timer n=1 5sec
~XX515 3 7E 30 30 35 31 35 20 32 0D Menu Timer n=3 & 10sec
~XX518 2
~nnnnnnnnnn
~XX518 5
~nnnnnnnnnn
~XX518 8
~nnnnnnnnnn
~XX518 13
~nnnnnnnnnn
~XX519 1 7E 30 30 35 31 39 20 31 0D Input Name Reset Reset all input name to default
~XX101 1 7E 30 30 31 30 31 20 31 0D High Altitude On
~XX101 0 7E 30 30 31 30 31 20 30 0D Off (0/2 for backward compatible)
~XX348 1 7E 30 30 33 34 38 20 31 0D Display Mode Lock On
~XX348 0 7E 30 30 33 34 38 20 30 0D Display Mode Lock Off
~XX103 1 7E 30 30 31 30 33 20 31 0D Keypad Lock On
~XX103 0 7E 30 30 31 30 33 20 30 0D Off (0/2 for backward compatible)
~XX102 1 7E 30 30 31 30 32 20 31 0D Information Hide On
~XX102 0 7E 30 30 31 30 32 20 30 0D Off (0/2 for backward compatible)
~XX104 0 7E 30 30 31 30 34 20 30 0D Background Color None
~XX104 1 7E 30 30 31 30 34 20 31 0D Background Color Blue
~XX104 3 7E 30 30 31 30 34 20 33 0D Background Color Red
~XX104 4 7E 30 30 31 30 34 20 34 0D Background Color Green
~XX104 6 7E 30 30 31 30 34 20 36 0D Background Color Gray
~XX104 7 7E 30 30 31 30 34 20 37 0D Background Color Logo
~XX80 1 7E 30 30 38 30 20 31 0D Mute On
~XX80 0 7E 30 30 38 30 20 30 0D Off (0/2 for backward compatible)
~XX81 n 7E 30 30 38 31 20 a 0D Volume(Audio) n = 0 (a=30) ~ 10 (a=31 30)
~XX454 0 7E 30 30 34 35 34 20 30 0D Crestron Off
~XX454 1 7E 30 30 34 35 34 20 31 0D On
~XX455 0 7E 30 30 34 35 35 20 30 0D Extron Off
~XX455 1 7E 30 30 34 35 35 20 31 0D On
~XX456 0 7E 30 30 34 35 36 20 30 0D PJLink Off
~XX456 1 7E 30 30 34 35 36 20 31 0D On
~XX457 0 7E 30 30 34 35 37 20 30 0D AMX Device Discovery Off
~XX457 1 7E 30 30 34 35 37 20 31 0D On
~XX458 0 7E 30 30 34 35 38 20 30 0D Telnet Off
~XX458 1 7E 30 30 34 35 38 20 31 0D On
~XX459 0 7E 30 30 34 35 38 20 30 0D HTTP Off
~XX459 1 7E 30 30 34 35 38 20 31 0D On
~XX313 1 7E 30 30 33 31 33 20 31 0D Information menu On
~XX313 0 7E 30 30 33 31 33 20 30 0D Information menu Off (0/2 for backward compatible)
~XX112 1 7E 30 30 31 31 32 20 31 0D Reset to Default Yes (P.S When security is off)
~XX112 1
~nnnn
~XX546 1 7E 30 30 35 34 36 20 31 0D Reset OSD
~XX210 n 7E 30 30 32 30 30 20 n 0D Display message on the
SEND to emulate Remote
232 ASCII
Code
~XX140 10 7E 30 30 31 34 30 20 31 30 0D Up
~XX140 11 7E 30 30 31 34 30 20 31 31 0D Left
HEX Code Function Description
7E 30 30 35 31 38 20 32 20 a 0DInput Name HDMI2 (a= 7E +nnnnnnnnnn)
7E 30 30 35 31 38 20 35 20 a 0DInput Name HDMI1/MHL (a= 7E +nnnnnnnnnn)
7E 30 30 35 31 38 20 38 20 a 0DInput Name VGA (a= 7E +nnnnnnnnnn)
7E 30 30 35 31 38 20 31 33 20
a 0D
7E 30 30 31 31 32 20 31 0D Reset to Default Yes (P.S When security is On/ Off)
HEX Code Function Description
Input Name Video (a= 7E +nnnnnnnnnn)
n: 1-30 characters
OSD
62
English
ADDITIONAL INFORMATION
SEND to emulate Remote
232 ASCII
Code
~XX140 12 7E 30 30 31 34 30 20 31 32 0D Enter (for projection MENU)
~XX140 13 7E 30 30 31 34 30 20 31 33 0D Right
~XX140 14 7E 30 30 31 34 30 20 31 34 0D Down
~XX140 15 7E 30 30 31 34 30 20 31 35 0D Keystone +
~XX140 16 7E 30 30 31 34 30 20 31 36 0D Keystone ~XX140 17 7E 30 30 31 34 30 20 31 37 0D Volume ~XX140 18 7E 30 30 31 34 30 20 31 38 0D Volume +
~XX140 19 7E 30 30 31 34 30 20 31 39 0D Brightness
~XX140 20 7E 30 30 31 34 30 20 32 30 0D Menu
~XX140 21 7E 30 30 31 34 30 20 32 31 0D Zoom
~XX140 28 7E 30 30 31 34 30 20 32 38 0D Contrast
~XX140 47 7E 30 30 31 34 30 20 34 37 0D Source
SEND from projector automatically
232 ASCII
Code
when Standby/Warming/Cooling/Out of
Range/Lamp fail/Fan Lock/Over Temperature/
Lamp Hours Running Out
READ from projector
232 ASCII
Code
~XX87 1 7E 30 30 38 37 20 31 0D LAN Settings /Network
~XX87 3 7E 30 30 38 37 20 33 0D LAN Settings /IP Address (Read only)
~XX108 1 7E 30 30 31 30 38 20 31 0D Lamp Hours
~XX121 1 7E 30 30 31 32 31 20 31 0D Input Source Commands Oka a = 0 None
~XX122 1 7E 30 30 31 32 32 20 31 0D Sofware Version OKdddd dddd: FW version
~XX123 1 7E 30 30 31 32 33 20 31 0D Display Mode Oka a = 0 None
~XX124 1 7E 30 30 31 32 34 20 31 0D Power State OKn n : 0/1 = Off/On
~XX125 1 7E 30 30 31 32 35 20 31 0D Brightness OKn
~XX126 1 7E 30 30 31 32 36 20 31 0D Contrast OKn
~XX127 1 7E 30 30 31 32 37 20 31 0D Aspect Ratio Okaa aa = 2 16:9
~XX128 1 7E 30 30 31 32 38 20 31 0D Color Temperature Oka a=0 Medium
HEX Code Function Description
HEX Code Function
HEX Code Function
State
Projector Return
INFOn n : 0/1/2/3/4/6/7/8 =
Projector Return
(Read only)
Description
n: Standby/Warming/Cooling/Out of Range/
Lamp fail/Fan Lock/Over Temperature/
Lamp Hours Running Out
Description
a = 2 VGA
a = 5 Video
a = 7 HDMI1
a = 8 HDMI2
a = 13 Network Display
a = 14 USB Display
a = 17 Multimedia
a = 1 Presentation
a = 2 Bright
a = 3 Cinema
a = 4 sRGB
a = 5 User (1)
a = 9 3D
a = 10 DICOM SIM.
a = 12 Game
aa=3 16:10 [WXGA WUXGA models]
aa=5 LBX [except for SVGA XGA models]
aa=6 Native
aa=7 Auto
a=1 D50/Cool
a=3 D70/Warm
English
63
ADDITIONAL INFORMATION
READ from projector
232 ASCII
Code
~XX129 1 7E 30 30 31 32 39 20 31 0D Projection Mode OKn n = 0 Front-Desktop
~XX150 1 7E 30 30 31 35 30 20 31 1D Information Okabbbbbcc
~XX150 4 7E 30 30 31 35 30 20 34 0D Resolution Oka a = string (e.g. Ok1920x1080)
~XX150 16 7E 30 30 31 35 30 20 31 36 0D Standby Power Mode Oka a=1 Active
~XX150 19 7E 30 30 31 35 30 20 31 39 0D Refresh rate Oka a = string (Refresh rate e.g. Ok60Hz)
~XX151 1 7E 30 30 31 35 31 20 31 0D Model name OKa a=1 SVGA
~XX108 1 7E 30 30 31 30 38 20 31 0D Lamp Hours Okbbbb bbbb: LampHour
~XX321 1 7E 30 30 33 32 31 20 31 0D Filter Usage Hours OKbbbb bbbb: Filter Usage Hours
~XX352 1 7E 30 30 33 35 32 20 31 0D System Temperature Okaaaa aaa=000~999
~XX353 1 7E 30 30 33 35 33 20 31 0D Serial number Okaaaaaaaaaaaa
~XX354 1 7E 30 30 33 35 34 20 31 0D Closed Captioning Oka a = 0 Off
~XX355 1 7E 30 30 33 35 35 20 31 0D AV Mute Oka a = 0 Off
~XX356 1 7E 30 30 33 35 36 20 31 0D Mute Oka a = 0 Off
~XX357 1 7E 30 30 33 35 37 20 31 0D LAN FW version Okeeeee eeeee = Software Version
~XX543 1 7E 30 30 35 34 33 20 31 0D H ImageShift Oka a=nnnn
~XX543 2 7E 30 30 35 34 33 20 32 0D V Image Shift Oka a=nnnn
~XX543 3 7E 30 30 35 34 33 20 33 0D V Keystone Oka a=nnn
~XX558 1 7E 30 30 35 35 38 20 31 0D Projector ID Oka a=nn
HEX Code Function
Projector Return
ddddee
aaaaa
Description
n = 1 Rear-Desktop
n = 2 Front-Ceiling
n = 3 Rear-Ceiling
a : Power Status
a=0 Power Off
a=1 Power On”
b = Lamp Hour
bbbbb Lamp Hour
c = Input Source
cc=00 None
cc=02 VGA1
cc=05 Video
cc=07 HDMI1
cc=08 HDMI2
cc=12 Network Display(Presenter)
cc=13 USB Display
cc=17 Multimedia
d = Firmware Version
dddd Firmware Version”
e = Display mode
ee=00 None
ee=01 Presentation
ee=02 Bright
ee=03 Cinema
ee=04 sRGB
ee=05 User(1)
ee=09 3D
ee=10 DICOM SIM.
ee=12 Game
a=0 Eco.
a=2 XGA
a=3 WXGA
serial number string
a = 1 CC1
a = 2 CC2”
a = 1 On
a = 1 On
64
English
ADDITIONAL INFORMATION
Note:
~xx112 1 ~nnnn (nnnn = password) When security is on, you need to add password after command or
it will return F.
When the projector show other OSD, user key the command “~XX313 0 7E 30 30 33 31 33 20 30 0D
Information menu Off (0/2 for backward compatible)” then it will return F.
English
65
ADDITIONAL INFORMATION
IR remote codes
Power Switch
Freeze
L
Enter
-
Page
Keystone Volume
-
+
1 2
Menu33D
4
HDMI5VGA6Video
7
User18User29User3
Source
Key
Repeat
Format
Address Data
Byte 1 Byte 2 Byte 3 Byte 4
Power F1 32 CD 81 7E Power on/off
Switch F1 32 CD 3E C1 Switch
Display blank /
Audio mute
F1 32 C D 8A 75
Freeze F1 32 CD 8B 74 Freeze
Mute F1 32 CD 92 6D
R
Page+Laser
-
+
0
Resync
Printing-key
definition
Description
Press to turn on / off the
projector.
Press to switch the USB
mouse on / off.
Press to hide / unhide the
screen picture and turn off /
on audio.
Press to freeze the projector
image.
Press to momentarily turn off
/ on the audio.
Mouse left click L F1 32 CD CB 34 L Use as mouse left click.
Mouse right click R F1 32 CD CC 33 R Use as mouse right click.
F2 32 CD C6 39 Up arrow
Four
directional select
keys
F2 32 CD C8 37 Left arrow
F2 32 CD C9 36 Right arrow
Use to select
items or make adjustments
to your selection.
F2 32 CD C7 38 Down arrow
Enter F1 32 CD C5/CA 3A/35 Enter Conrm your item selection.
Page - F2 32 CD C2 3D Page- Press to page down.
Laser ± ± ± ± ± Laser Use as laser pointer.
Page + F2 32 CD C1 3E Page+ Press to page up.
66
English
ADDITIONAL INFORMATION
-
-
Key
Repeat
Format
Address Data
Byte 1 Byte 2 Byte 3 Byte 4
Printing-key
definition
F2 32 CD 85 7A Keystone+
Keystone
Volume
Aspect ratio / 1 F1 32 CD 98 67
+
F2 32 CD 84 7B Keystone-
+
F2 32 CD 8C 73 Volume +
F2 32 CD 8F 70 Volume -
/ 1
Menu / 2 F1 32 CD 88 77 Menu/2
3D / 3 F1 32 CD 93 6C 3D/3
HDMI / 4 F1 32 CD 86 79 HDMI/4
VGA / 5 F1 32 CD D0 2F VGA/5
Video / 6 F1 32 CD D1 2E Video/6
F1 32 CD D2 2D User 1/7 User dened keys.
F1 32 CD D3 2C User 2/8
User1 / 7; User2 / 8; User3
/ 9
F1 32 CD D4 2B User 3/9
Source F1 32 CD C3 3C Source
Brightness mode
/ 0
F1 32 CD 96 69
/ 0
Re-sync F1 32 CD C4 3B Re-Sync
Description
Press to adjust image distortion caused by tilting the
projector.
Press to adjust to increase /
decrease the volume.
Press to change
aspect ratio of a
displayed image.
Use as numeric
keypad number "1".
Press to display or
exit the on-screen
display menus for
projector.
Use as numeric
keypad number "2".
Press to manually
select a 3D mode
that matches your 3D
content.
Use as numeric
keypad number "3".
Press to choose
HDMI source.
Use as numeric
keypad number "4".
Press to choose VGA
source.
Use as numeric
keypad number "5".
Press to choose
composite video
source.
Use as numeric
keypad number "6".
Please see page
40.
Use as numeric
keypad numbers
"7", "8", and "9"
accordingly.
Press to select an input
signal.
Press to automatically
adjust the picture
brightness to give
an optimum contrast
performance.
Use as numeric
keypad number "0".
Press to automatically synchronize the projector to the
input source.
English
67
ADDITIONAL INFORMATION
Troubleshooting
If you experience a problem with your projector, please refer to the following information. If a problem persists,
please contact your local reseller or service center.
Image problems
No image appears on-screen
Ensure all the cables and power connections are correctly and securely connected as described in the
"Installation" section.
Ensure the pins of connectors are not crooked or broken.
Check if the projection lamp has been securely installed. Please refer to the "Replacing the Lamp"
section.
Image is out of focus
Adjust the focus ring on the projector lens.
Make sure the projection screen is between the required distance from the projector. (Please refer to
pages 55-56).
The image is stretched when displaying 16:9 DVD title
When you play anamorphic DVD or 16:9 DVD, the projector will show the best image in 16: 9 format
on projector side.
If you play the LBX format DVD title, please change the format as LBX in projector OSD.
If you play 4:3 format DVD title, please change the format as 4:3 in projector OSD.
Please setup the display format as 16:9 (wide) aspect ratio type on your DVD player.
Image is too small or too large
Adjust the zoom lever on the top of the projector.
Move the projector closer to or further from the screen.
Press "Menu" on the projector panel, go to "Display >Aspect Ratio". Try the different settings.
Image has slanted sides:
If possible, reposition the projector so that it is centered on the screen and below the bottom of the
screen.
68
Use "Display > Geometric Correction > H Keystone or V Keystone" from the OSD to make an
adjustment.
Image is reversed
Select "Setup > Projection" from the OSD and adjust the projection direction.
Blurry double image
Press "3D" button and switch to "Off" to avoid normal 2D image is blurry double image.
English
ADDITIONAL INFORMATION
Two images, side-by-side format
Press "3D" button and switch to "SBS" for input signal is HDMI 1.3 2D 1080i side-by-side.
Image does not display in 3D
Check if the battery of 3D glasses is drained.
Check if the 3D glasses is turned on.
When the input signal is HDMI 1.3 2D (1080i side-by-side half), press "3D" button and switch to "SBS".
Other problems
The projector stops responding to all controls
If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before
reconnecting power.
Lamp burns out or makes a popping sound
When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this
happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp,
follow the procedures in the "Replacing the Lamp" section on pages 50-51.
Remote control problems
If the remote control does not work
Check the operating angle of the remote control is pointed within ±10° to the IR receiver on the
projector.
Make sure there are not any obstructions between the remote control and the projector. Move to within
6 m (20 ft) of the projector.
Make sure batteries are inserted correctly.
Replace batteries if they are exhausted.
Warning indicators
When the warning indicators (see below) light up or ash, the projector will automatically shutdown:
"LAMP" LED indicator is lit red and if "On/Standby" indicator ashes red.
"TEMP" LED indicator is lit red and if "On/Standby" indicator ashes red. This indicates the projector
has overheated. Under normal conditions, the project can be switched back on.
"TEMP" LED indicator ashes red and if "On/Standby" indicator ashes red.
Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up or
English
69
ADDITIONAL INFORMATION
ash, please contact your nearest service center for assistance.
LED lightning messages
Message
Standby state
(Input power cord)
Power on (Warming)
Power on and Lamp
lighting
Power off (Cooling)
Quick Resume (100
secs)
Error (Lamp fail) Flashing Steady light
Error (Fan failure) Flashing Flashing
Error (Over Temp) Flashing Steady light
Standby State
(Burn in mode)
Burnin (Warming) Flashing
Burnin (Cooling) Flashing
Power On
(Burn in Mode)
Power LED Power LED
(Red) (Green or Blue) (Red) (Red)
Steady light
Flashing
(0.5 sec off /
0.5 sec on)
Steady light
Flashing
(0.5 sec off /
0.5 sec light). Back
to red steady light
when cooling fan
turns off.
Flashing
(0.25 sec off /
0.25 sec light)
Flashing
(0.5 sec off /
0.5 sec on)
Flashing
1 sec off
3 sec light
Flashing
(0.5 sec off /
0.5 sec on)
Flashing
1 sec off
3 sec light
Temp-LED
Flashing
(0.5 sec off /
0.5 sec on)
Flashing
1 sec off
3 sec light
Lamp-LED
Flashing
(0.5 sec off /
0.5 sec on)
Flashing
1 sec off
3 sec light
Power off:
Lamp warning:
Power Off
Power Off?
Press power key again.
Warning
Lamp Warning
Lamp life exceeded.
70
English
ADDITIONAL INFORMATION
Temperature warning:
Warning
TEMPERATURE TOO HIGH
Please:
1. Make sure air in and outlets are not blocked.
2. Make sure the environment temperature is under 45 degree C.
If the problem persists in spite of the above.
Please contact a service center for repair.
Fan failed:
Warning
FAN LOCKED
The projector will switch off automatically
Please contact a service center for repair.
Out of display range:
HDMI
Out Of Range
Power down warning:
Power Down
Power Down Timer Active
Power down in sec.
Security timer alarm:
Warning
Security Timer Alarm
Time Out in sec.
English
71
ADDITIONAL INFORMATION
Specications
Optical Description
Maximum resolution UXGA, 1600x1200, 60Hz WUXGA for WXGA 16:10
Native resolution SVGA/XGA/WXGA
Lens - Manual zoom and manual focus
- Bright Mode (Normal Mode) 5000 Hours Standard @190W, 50% Survival Rate
Lamp life
Image size (diagonal)
Projection distance
Electrical Description
Inputs
Outputs
Control
- STD Mode (ECO Mode) 6000 Hours Typical @160W, 50% Survival Rate
- Dynamic mode 6500 Hours
- DE Mode in education cycle 10000 Hours
SVGA/XGA: 27.34” ~ 304.5”
WXGA: 29.8” ~ 300.6”
SVGA/XGA: 1.2m ~ 12.0m (focus range)
WXGA: 1.1m ~ 10.1m (focus range)
- HDMI 1.4a
- HDMI 1.4a + MHL (v2.2)
- VGA-IN
- Audio 3.5mm
- VGA
- Audio 3.5mm
- USB-A power
- RJ45
- RS232
- USB mouse / service
Color reproduction 1073.4 Million color
Scan rate
Built-in speaker Yes, 15W
Power requirement 100 - 240V AC 50/60Hz
Input current 2.5-1.0 A
Mechanical Description
Installation orientation Front, Rear, Ceiling - top, Rear - top
Dimensions
Weight - 2.5 ± 0.5 kg
Environmental conditions Operating in 5 ~ 40°C , 10% to 85% humidity (non-condensing)
Note: All specications are subject to change without notice.
- Horizontal scan rate: 15.375~91.146 KHz
- Vertical scan rate: 24~ 85 Hz (120Hz for 3D feature projector)
- 298 mm (W) x 230 mm (D) x 83 mm (H) (without feet)
- 298 mm (W) x 230 mm (D) x 96.5 mm (H) (with feet)
72
English
ADDITIONAL INFORMATION
Optoma global ofces
For service or support, please contact your local ofce.
USA
3178 Laurelview Ct. 888-289-6786
Fremont, CA 94538, USA 510-897-8601
www.optomausa.com services@optoma.com
Canada
3178 Laurelview Ct. 888-289-6786
Fremont, CA 94538, USA 510-897-8601
www.optomausa.com services@optoma.com
Latin America
3178 Laurelview Ct. 888-289-6786
Fremont, CA 94538, USA 510-897-8601
www.optomausa.com services@optoma.com
Europe
Unit 1, Network 41, Bourne End Mills
Hemel Hempstead, Herts,
HP1 2UJ, United Kingdom +44 (0) 1923 691 800
www.optoma.eu +44 (0) 1923 691 888
Service Tel : +44 (0)1923 691865 service@tsc-europe.com
Benelux BV
Randstad 22-123 +31 (0) 36 820 0252
1316 BW Almere +31 (0) 36 548 9052
The Netherlands
www.optoma.nl
Japan
東京都足立区綾瀬3-25-18
株式会社オーエス info@os-worldwide.com
コンタクトセンター:0120-380-495 www.os-worldwide.com
Taiwan
12F., No.213, Sec. 3, Beixin Rd., +886-2-8911-8600
Xindian Dist., New Taipei City 231, +886-2-8911-6550
Taiwan, R.O.C. services@optoma.com.tw
www.optoma.com.tw asia.optoma.com
Hong Kong
Unit A, 27/F Dragon Centre,
79 Wing Hong Street, +852-2396-8968
Cheung Sha Wan, +852-2370-1222
Kowloon, Hong Kong www.optoma.com.hk
China
5F, No. 1205, Kaixuan Rd., +86-21-62947376
Changning District +86-21-62947375
Shanghai, 200052, China www.optoma.com.cn
France
Bâtiment E +33 1 41 46 12 20
81-83 avenue Edouard Vaillant +33 1 41 46 94 35
92100 Boulogne Billancourt, France savoptoma@optoma.fr
Spain
C/ José Hierro,36 Of. 1C +34 91 499 06 06
28522 Rivas VaciaMadrid, +34 91 670 08 32
Spain
Deutschland
Wiesenstrasse 21 W +49 (0) 211 506 6670
D40549 Düsseldorf, +49 (0) 211 506 66799
Germany info@optoma.de
Scandinavia
Lerpeveien 25 +47 32 98 89 90
3040 Drammen +47 32 98 89 99
Norway info@optoma.no
PO.BOX 9515
3038 Drammen
Norway
Korea
WOOMI TECH.CO.,LTD. +82+2+34430004
4F, Minu Bldg.33-14, Kangnam-Ku, +82+2+34430005
Seoul,135-815, KOREA
korea.optoma.com
English
73
www.optoma.com
*36.7AZ01G001-A*
P/N:36.7AZ01G001-A
Loading...