How it Works
Optoma
Loading...
UHD550X
User Manual
61 pgs12.5 Mb0
Technical data [de]
3 pgs578.56 Kb0
Product Sheet
3 pgs573.33 Kb0

Optoma UHD65, UHD60, UHD550X User Manual

DLP® Projector
User manual
TABLE OF CONTENTS
SAFETY ............................................................................................... 4
INTRODUCTION .................................................................................. 8
Connections.............................................................................................................................. 10
Keypad ..................................................................................................................................... 10
Remote control ......................................................................................................................... 12
SETUP AND INSTALLATION ............................................................. 13
Installing the projector .............................................................................................................. 13
Connecting sources to the projector ......................................................................................... 14
Adjusting the projector image ................................................................................................... 15
Remote setup ........................................................................................................................... 16
USING THE PROJECTOR .................................................................. 18
Powering on / off the projector.................................................................................................. 18
Selecting an input source ......................................................................................................... 19
USING THE PROJECTOR .................................................................. 20
Menu navigation and features .................................................................................................. 20
OSD Menu tree......................................................................................................................... 21
Display image settings menu.................................................................................................... 29
Display aspect ratio menu ........................................................................................................ 31
Display edge mask menu ......................................................................................................... 33
Display digital zoom menu........................................................................................................ 33
Display image shift menu ......................................................................................................... 33
Audio internal speaker menu .................................................................................................... 33
Audio mute menu ..................................................................................................................... 33
Audio volume menu .................................................................................................................. 33
Setup projection menu.............................................................................................................. 34
Setup lamp settings menu ........................................................................................................ 34
Setup lter settings menu ......................................................................................................... 34
2
English
Setup power settings menu ...................................................................................................... 34
Setup security menu ................................................................................................................. 35
Setup test pattern menu ........................................................................................................... 35
Setup remote settings menu..................................................................................................... 35
Setup projector ID menu........................................................................................................... 35
Setup 12V trigger menu............................................................................................................ 36
Setup options menu.................................................................................................................. 36
Setup reset OSD menu ............................................................................................................ 37
Network LAN menu .................................................................................................................. 37
Network control menu............................................................................................................... 38
Setup network control settings menu ....................................................................................... 39
Info menu.................................................................................................................................. 44
MAINTENANCE .................................................................................. 45
Replacing the lamp ................................................................................................................... 45
Installing and cleaning the dust lter ........................................................................................ 47
ADDITIONAL INFORMATION ............................................................ 48
Compatible resolutions ............................................................................................................. 48
Image size and projection distance .......................................................................................... 50
Projector dimensions and ceiling mount installation ................................................................. 52
IR remote codes ....................................................................................................................... 53
Troubleshooting ........................................................................................................................ 55
Warning indicators .................................................................................................................... 57
Specications ........................................................................................................................... 59
Optoma global ofces ............................................................................................................... 60
English
3
SAFETY
The lightning ash with arrow head within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufcient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Please follow all warnings, precautions and maintenance as recommended in this user's guide.
Important Safety Instruction
To prolong the effective life of the lamp, make sure to keep the lamp on for at least 60 seconds and
avoid performing force shutdown.
RG2
Do not stare into the beam, RG2. As with any bright source, do not stare into the direct beam, RG2 IEC 62471-5:2015.
Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from
over heating, it is recommended to install the projector in a location that does not block ventilation. As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the projector in an enclosure such as a book case or a cabinet that restricts air ow.
To reduce the risk of re and/or electric shock, do not expose the projector to rain or moisture. Do not
install near heat sources such as radiators, heaters, stoves or any other apparatus such as ampliers that emits heat.
Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short
out parts that could result in re or electric shock.
Do not use under the following conditions:
± In extremely hot, cold or humid environments.
(i) Ensure that the ambient room temperature is within 5°C ~ 40°C
(ii) Relative humidity is 10% ~ 85%
± In areas susceptible to excessive dust and dirt.
± Near any appliance generating a strong magnetic eld.
± In direct sunlight.
4
Do not use the projector in places where ammable gases or explosives gases may be present in the
atmosphere. The lamp inside the projector becomes very hot during operation and the gases may ignite and result in a re.
Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be
(but not limited to):
± Unit has been dropped.
± Power supply cord or plug has been damaged.
± Liquid has been spilled on to the projector.
± Projector has been exposed to rain or moisture.
± Something has fallen in the projector or something is loose inside.
Do not place the projector on an unstable surface. The projector may fall over resulting in injury or the
projector may become damaged.
English
Do not block the light coming out of the projector lens when in operation. The light will heat the object
and my melt, cause burns or start a re.
Please do not open or disassemble the projector as this may cause electric shock.
Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous
voltages or other hazards. Please call Optoma before you send the unit for repair.
See projector enclosure for safety related markings.
The unit should only be repaired by appropriate service personnel.
Only use attachments/accessories specied by the manufacturer.
Do not look into straight into the projector lens during operation. The bright light may harm your eyes.
When replacing the lamp, please allow the unit to cool down. Follow instructions as described on
pages 45-46.
This projector will detect the life of the lamp itself. Please be sure to change the lamp when it shows
warning messages.
Reset the "Lamp Reset" function from the on-screen display "Setup lamp settings" menu after
replacing the lamp module.
When switching the projector off, please ensure the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the projector to cool down.
When the lamp is approaching to the end of its life time, the message "Lamp life exceeded." will show
on the screen. Please contact your local reseller or service center to change the lamp as soon as possible.
Turn off and unplug the power plug from the AC outlet before cleaning the product.
Use a soft dry cloth with mild detergent to clean the display housing. Do not use abrasive cleaners,
waxes or solvents to clean the unit.
Disconnect the power plug from AC outlet if the product is not being used for a long period of time.
Note: When the lamp reaches the end of its life, the projector will not turn back on until the lamp module has been
replaced. To replace the lamp, follow the procedures listed under “Replacing the Lamp” section on pages 45-46.
Do not setup the projector in places where it might be subjected to vibration or shock.
Do not touch the lens with bare hands
Remove battery/batteries from remote control before storage. If the battery/batteries are left in the
remote for long periods, they may leak.
Do not use or store the projector in places where smoke from oil or cigarettes may be present, as it
can adversely affect the quality of the projector performance.
Please follow the correct projector orientation installation as non standard installation may affect the
projector performance.
Use a power strip and or surge protector. As power outages and brown-outs can KILL devices.
English
5
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.
© Copyright 2017
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specically disclaims any implied warranties of merchantability or tness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending applications in other countries throughout the world.
HDMI, the HDMI Logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
DLP®, DLP Link and the DLP logo are registered trademarks of Texas Instruments and BrilliantColorTM is a
trademark of Texas Instruments.
All other product names used in this manual are the properties of their respective owners and are Acknowledged.
MHL, Mobile High-Denition Link and the MHL Logo are trademarks or registered trademarks of MHL Licensing, LLC.
FCC
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.
6
English
Caution
Changes or modications not expressly approved by the manufacturer could void the user's authority, which is granted by the Federal Communications Commission, to operate this projector.
Operation Conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Remarque l'intention des utilisateurs canadiens
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.
Declaration of Conformity for EU countries
EMC Directive 2014/30/EC (including amendments)
Low Voltage Directive 2014/35/EC
R & TTE Directive 1999/5/EC (if product has RF function)
WEEE
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle it.
English
7
INTRODUCTION
Package Overview
Carefully unpack and verify that you have the items listed below under standard accessories. Some of the items under optional accessories may not be available depending on the model, specication and your region of purchase. Please check with your place of purchase. Some accessories may vary from region to region.
The warranty card is only supplied in some specic regions. Please consult your dealer for detailed information.
Standard accessories
ON
OFF
User2
User1
User3
Contrast
Brightness
Mode
Aspect ratio
Keystone
3D
DB
Sleep Timer
Mute
Volume
Source
Re-sync
Menu
Volume
HDMI1
HDMI2
VGA1
VGA2 Video YPbPr
Projector Remote control Power lead Documentation
Warranty Card*

Basic User Manual

Note:
The remote control is shipped with the battery.
* For European warranty Information, please visit www.optoma.com.
Optional accessories
HDMI cable Lens cap CD user manual
Note: Optional accessories vary depending on model, specication and region.
8
English
INTRODUCTION
Product Overview
6
21
11 11
3 4
5
Minimum 100mm
Minimum 100mm
7
8
9
9
10
4
Minimum 100mm
Minimum 300mm
Minimum 300mm
Minimum 100mm
Note:
Do not block projector intake and exhaust vents.
When operating the projector in an enclosed space, allow at least 30 cm clearance around the intake
and exhaust vents.
No Item No Item
1. Top Cover 7. Zoom Lever
2.
Focus Ring
Lens Shift Dial
8.
3. Lens 9. Ventilation (outlet)
4. IR Receiver 10. Keypad
5. Input / Output 11. Tilt-Adjustment Foot
6. Ventilation (inlet)
English
9
INTRODUCTION
Connections
1 6 743 5 9 10 118
No Item No Item
1. KensingtonTM Lock Port 8. AUDIO IN Connector
2. Power Socket 9. 12V OUT Connector
3. RJ-45 Connector 10. USB Type A / Service Connector
4. RS232 Connector 11. S/PDIF Connector
5. HDMI 1 Connector 12. USB Power Out (5V 1.5A)
HDMI 2 (HDCP2.2) / MHL
6. Connector (*)
7. VGA Connector
2
13
12
13. AUDIO OUT Connector
Note:
USB Type A supports mouse / service capability.
Remote mouse requires special remote control.
(*)Only HDMI 2 (HDCP2.2) connector supports 4K (Ultra HD) at 60Hz refresh rate.
Keypad
10
English
INTRODUCTION
1 2
8
5 467
No Item No Item
1.
2.
3.
4.
Menu
Enter
Re-Sync
Temp LED
Lamp LED
5.
Source
6.
Power and On/Standby LED
7.
Four Directional Select Keys
8.
3
English
11
INTRODUCTION
Remote control
10
11
12
1
ON
OFF
14
2
3
User1
Brightness
User2
Contrast
User3
Mode
4
Mute
Source
Aspect ratio
DB
Volume
3D
Sleep Timer
Re-sync
5
Keystone
6
7
8
15
16
17
18
19
20
21
22
9
Menu
HDMI1
Volume
HDMI2
23
24
25
VGA1
VGA2 Video YPbPr
26
13
27
No Item No Item
1. Power On 15. User 3
User 2 16. Contrast
2.
3. User 1 17. Display Mode
4. Brightness 18. Aspect Ratio
5. Keystone (not supported) 19. 3D Menu On / Off (not supported)
6. Mute 20. Sleep Timer
7. DB (Dynamic Black) 21. Volume +
8. Source 22. Re-Sync
9. Enter 23. Four Directional Select Keys
10. Menu 24. Volume -
11. HDMI1 25. HDMI2
12. VGA1 26. YPbPr (not supported)
13. VGA2 (not supported) 27. Video (not supported)
14. Power Off
Note: Some keys may have no function for models that do not support these features.
English
12
SETUP AND INSTALLATION
Installing the projector
Your projector is designed to be installed in one of four possible positions.
Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment.
Table mount front Ceiling mount front
Table mount rear Ceiling mount rear
Projector should be placed at on a surface and 90 degrees / perpendicular to the screen.
How to determine projector location for a given screen size, please refer to distance table on pages
50-51.
How to determine screen size for a given distance, please refer to distance table on pages 50-51.
Note: The further away the projector is placed from the screen the projected image size increases and vertical
offset also increases proportionally.
IMPORTANT!
Do not operate the projector in any orientation other that table top or ceiling mount. The projector should be horizontal and not tilted either forwards/backwards or left/right. Any other orientation will invalidate the warranty and may shorten the lifetime of the projector lamp or the projector itself. For none standard installation advise please contact Optoma.
English
13
SETUP AND INSTALLATION
Connecting sources to the projector
1
2
3
4
5
6
14
13
12
MOLEX
11
10
9
MOLEX
7
8
14
English
No Item No Item
1. HDMI Cable 8. S/PDIF Out Cable
HDMI / MHL Cable
2.
USB Power Cable
9.
3. RCA Component Cable 10. Audio Out Cable
4. VGA In Cable 11. HDMI Dongle
5. Audio In Cable 12. RS232 Cable
6. 12V DC Jack 13. RJ-45 Cable
7. USB Cable 14. Power Cord
SETUP AND INSTALLATION
Adjusting the projector image
Image height
The projector is equipped with elevator feet for adjusting the image height.
1. Locate the adjustable foot you wish to adjust on the underside of the projector.
2. Rotate the adjustable foot clockwise or counterclockwise to raise or lower the projector.
Zoom, lens shift, and focus
To adjust the image size and position, do the following:
a. Push down rmly on the middle of the top cover to unlock the latch. Then open the top cover.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
Zoom Lever
Lens Shift
b. To adjust the image size, turn the zoom lever clockwise or counterclockwise to increase or decrease
the projected image size.
c. To adjust the image position, turn the lens shift dial clockwise or counterclockwise to adjust the
position of the projected image vertically.
English
15
SETUP AND INSTALLATION
To adjust the focus, turn the focus ring clockwise or counterclockwise until the image is sharp and
legible.
Note: The projector will focus at a distance of 1.3m to 9.3m.
Remote setup
Installing / replacing the batteries
Two AAA size batteries are supplied for the remote control.
Focus Ring
1. Remove the battery cover on the back of the remote control.
2. Insert AAA batteries in the battery compartment as illustrated.
3. Replace back cover on remote control.
Note: Replace only with the same or equivalent type batteries.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
Do not mix batteries of different types. Different types of batteries have different characteristics.
Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or
cause chemical leakage in old batteries.
Remove batteries as soon as the are depleted. Chemicals that leak from batteries that come in contact
with skin can cause a rash. If you nd any chemical leakage, wipe thoroughly with a cloth.
The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
16
If you will not be using the remote control for an extended period of time, remove the batteries.
When you dispose of the batteries, you must obey the law in the relative area or country.
English
SETUP AND INSTALLATION
Effective range
Infra-Red (IR) remote control sensor is located on the front side and rear side of the projector. Ensure to hold the remote control at an angle within 30 degrees perpendicular to the projector’s IR remote control sensor to function correctly. The distance between the remote control and the sensor should not be longer than 7 meters (~ 23 feet).
Make sure that there are no obstacles between the remote control and the IR sensor on the projector
that might obstruct the infra-red beam.
Make sure the IR transmitter of the remote control is not being shined by sunlight or uorescent lamps
directly.
Please keep the remote controller away from uorescent lamps for over 2 meters or the remote
controller might become malfunction.
If the remote control is closed to Inverter-Type uorescent lamps, it might become ineffective from time
to time.
If the remote control and the projector are within a very short distance, the remote control might
become ineffective.
When you aim at the screen, the effective distance is less than 5 meters from the remote control to the
screen and reecting the IR beams back to the projector. However, the effective range might change according to screens.
Approx. ±15°
Menu
HDMI1
VGA1
HDMI2
VGA2
Video
YPbPr
Approx. ±15°
ON
User1
Brightne ss
User2
OFF
Contrast
Keystone
Aspect r atio
User3
Mute
Mode
DB
Source
Volume
3D
Sleep Ti mer
Re-sync
Volume
ON
User1
Brightne ss
User2
OFF
Contrast
Keystone
Aspect r atio
User3
Mute
Mode
DB
Source
Volume
3D
Sleep Ti mer
Menu
Re-sync
Volume
HDMI1
VGA1
HDMI2
VGA2
Video
YPbPr
English
17
USING THE PROJECTOR
ON
OFF
User2
User1
User3
Powering on / off the projector
or
ON
User1
Brightness
Keystone
Source
VGA1
Mute
Menu
HDMI1
User2
Contrast
Aspect ratio
DB
Sleep Timer
Volume
Volume
HDMI2
VGA2 Video YPbPr
Mode
Re-sync
OFF
User3
3D
Powering on
1. Securely connect the power lead and signal/source cable. When connected, the On/Standby LED will turn red.
2. Turn on the projector by pressing the " " on the projector keypad or the remote control.
3. A start up screen will display in approximately 10 seconds and the On/Standby LED will be ashing blue.
Note: The rst time the projector is turned on, you will be prompted to select the preferred language, projection
orientation, and other settings.
Powering off
1. Turn off the projector by pressing the " " on the projector keypad or the “ ” on the remote control.
2. The following message will be displayed:
Power Off
Power Off?
Press power key again.
3. Press the " " or the “ ” button again to conrm, otherwise the message will disappear after 15 seconds. When you press the " " or the “ ” button for the second time, the projector will shut down.
4. The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/ Standby LED will ash green or ash blue. When the On/Standby LED turns solid red, this indicates the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle has nished and the projector has entered standby mode. When the projector is in standby mode, simply press the " " button again to turn on the projector.
5. Disconnect the power lead from the electrical outlet and the projector.
Note: It is not recommended that the projector is turned on immediately, right after a power off procedure.
English
18
USING THE PROJECTOR
ON
OFF
Menu
User2
Contrast
Aspect ratio
DB
Volume
Source
Re-sync
User1
Brightness
Keystone
Mute
User3
Mode
3D
Sleep Timer
Selecting an input source
Turn on the connected source that you want to display on the screen, such as computer, notebook, video player, etc. The projector will automatically detect the source. If multiple sources are connected, push the source button on the projector keypad or the remote control to select the desired input.
or
ON
OFF
User2
User1
User3
Contrast
Brightness
Mode
Aspect ratio
Keystone
3D
DB
Sleep Timer
Mute
Volume
Source
Re-sync
Menu
Volume
HDMI1
HDMI2
VGA1
VGA2 Video YPbPr
English
19
Loading...
+ 42 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use