Optoma Technology TW615GOV User Manual

1

English

Usage Notice

Safety Information

The lightning ash with arrow head within an equilateral triangle is

intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may be of sufcient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

Class B emissions limits

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Important Safety Instruction

1. Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from over heating, it is recommended to install the projector in a location that does not block ventilation. As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the projector in an enclosure such as a book case or a cabinet that restricts air ow.

2. Do not use the projector near water or moisture. To reduce the risk of re and/or electric shock, do not expose the projector to rain or moisture.

3. Do not install near heat sources such as radiators, heaters, stoves or

any other apparatus such as ampliers that emits heat.

4. Clean only with dry cloth.

5. Only use attachments/accessories specied by the manufacturer.

6. Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be (but not limited to):

 Unit has been dropped.  Power supply cord or plug has been damaged.  Liquid has been spilled on to the projector.  Projector has been exposed to rain or moisture.  Something has fallen in the projector or something is loose inside.

Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please call Optoma before you send the unit for repair.

7. Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short out parts that could result in re or electric shock.

8. See projector enclosure for safety related markings.

9. The unit should only be repaired by appropriate service personnel.

3

English

Usage Notice

Precautions

Please follow all warnings, precautions and maintenance as recommended in this user’s guide.

▀■ Warning- Do not look into the projector’s lens when the lamp is

on. The bright light may hurt and damage your eyes.

▀■ Warning- To reduce the risk of re or electric shock, do not

expose this projector to rain or moisture.

▀■ Warning- Please do not open or disassemble the projector as

this may cause electric shock.

▀■ Warning- When replacing the lamp, please allow the unit to

cool down. Follow instructions as described on pages

55-56.

▀■ Warning- This projector will detect the life of the lamp itself.

Please be sure to change the lamp when it shows warning messages.

▀■ Warning- Reset the “Lamp Reset” function from the on-screen

display “OPTIONS | Lamp Settings” menu after replacing the lamp module (refer to page 49).

▀■ Warning- When switching the projector off, please ensure

the cooling cycle has been completed before disconnecting power. Allow 90 seconds for the projector to cool down.

▀■ Warning- Do not use lens cap when projector is in operation.

▀■ Warning- When the lamp is approaching the end of its lifetime,

the message “Lamp Warning: Lamp life exceeded.” will show on the screen. Please contact your local reseller or service center to change the lamp as soon

as possible.

▀■ Warning- Do not look into or point the laser pointer on your

remote control into your or someone’s eyes. Laser pointer can cause permanent damage to eyesight.

4

English

Usage Notice

Do:

  Turn off and unplug the power plug from the AC outlet before

cleaning the product.

  Use a soft dry cloth with mild detergent to clean the display

housing.

  Disconnect the power plug from AC outlet if the product is

not being used for a long period of time.

Do not:

  Block the slots and openings on the unit provided for

ventilation.

 Use abrasive cleaners, waxes or solvents to clean the unit.

 Use under the following conditions:

- In extremely hot, cold or humid environments.

Ensure that the ambient room temperature is within



5 - 40°C.

Relative Humidity is 5 - 40°C, 80% (Max.),



non-condensing.

- In areas susceptible to excessive dust and dirt.

- Near any appliance generating a strong magnetic eld.

- In direct sunlight.

5

English

Usage Notice

Eye Safety Warnings

▀■ Avoid staring/facing directly into the projector beam at all

times. Keep your back to the beam as much as possible.

▀■ When projector is used in a classroom, adequately supervise

students when they are asked to point out something on the

screen.

▀■ In order to minimize the lamp power, use room blinds to

reduce ambient light levels.

Product Features

Monitor loop

through only support in VGA1-In/ SCART/YPbPr.

▀■ XGA (1024x768) Native resolution /

WXGA (1280x800) Native resolution

▀■ HD compatible – 1080p supported

▀■ VGA monitor loop through

(works on standby mode > 1W)

▀■ BrilliantColorTM Technology

▀■ Security Bar and Kensington Lock

▀■ RS232 control

▀■ Rapid shutdown ▀■ Built-in speakers ▀■ Network support

6

English

Introduction

POWER

?

Package Overview

Unpack and inspect the box contents to ensure all parts listed below are in the box. If something is missing, please contact your nearest customer service center.

Due to different

applications in

each Country, some regions may have

different accessories.

Projector with lens cap

2 × AAA Batteries

Documentation :

User’s Manual



Warranty Card



Quick Start Card



WEEE Card



(for EMEA only)

Power Cord 1.8m

IR Remote Control

VGA Cable 1.8m

Carrying case

7

English

Introduction

VGA1-IN / YPbPr

/

VGA2-IN

/

SCART

/

YPbPr

VGA-OUT

S-VIDEO VIDEO

AUDIO-OUT

(VGA1)

AUDIO1-IN

RS-232

USB

(VGA2)

AUDIO2-IN

HDMI

RJ-45

(S-VIDEO/VIDEO)

AUDIO3-IN

?

POWER

12V OUT

POWER

?

Product Overview

Main Unit

2

3

5

4

5

1

6

9

8

1. Control Panel

2. Zoom Ring

3. Focus Ring

4. Zoom Lens

5. IR Receivers

7

6

6. Tilt-Adjustment Feet

7. Security Bar

8. Input / Output

Connections

9. Power Socket

8

English

Introduction

POWER

?

Control Panel

1

12

7

1. Help

2. Menu

3. Source

4. Enter

5. Re-Sync

6. Power

7. Keystone Correction

8. Four Directional Select Keys

9. On/Standby LED

10. Lamp Fail LED

11. Temp LED

12. IR Receiver

62 4 53

11

10

8

9

English

Introduction

VGA1-IN / YPbPr /

VGA2-IN

/

SCART / YPbPr

VGA-OUT

S-VIDEO VIDEO

AUDIO-OUT

(VGA

1)

AUDIO1-IN

RS-232

USB

(VGA 2)

AUDIO2-IN

HDMI

RJ-45

(S-VIDEO/VIDEO)

AUDIO3-IN

12V OUT

1 3

12V OUT

Input/Output Connections

5

87642

9

17

Monitor loop

through only support in VGA1-In/ SCART/YPbPr.

10

12

11

13

14

15

16

1. RJ-45 Networking Connector

2. USB Connector (Connect to PC for Remote Mouse

function)

3. HDMI Connector

4. VGA1-In/YPbPr/ Connector (PC Analog Signal/Component Video Input/HDTV/YPbPr/

Wireless Dongle)

5. VGA-Out Connector (Monitor Loop-through Output from

VGA1-In)

6. S-Video Input Connector

7. Composite Video Input Connector

8. Audio Output Connector (3.5mm Mini Jack)

9. 12V Trigger Relay Connector (12V, 750mA)

10. VGA2-In/SCART/YPbPr Connector (PC Analog Signal/Component Video Input/HDTV/SCART/

YPbPr)

11. RS-232 Connector (9-pin)

12. Audio 3 Input connector (3.5mm mini jack) (for S-Video/Video)

13. Audio 2 Input connector (3.5mm mini jack)

(for VGA2)

14. Audio 1 Input connector (3.5mm mini jack) (for VGA1)

15. KensingtonTM Lock Port

16. Security Bar

17. Power Socket

10

English

Installation

Remote Control

1

2

12

13

14

15

16

17

18

19

20

1. LED Indicator

2. Power On/Off

3. Four Directional

Select Keys

4. Mouse Right Click

5. Page Up

6. Re-Sync

24

7. Page Down

8. Volume +/-

9. 3D

3

10. AV mute

4

11. Video

12. PC/Mouse control

5

13. Mouse Left Click

6

14. Enter/Help

7

15. Source

16. Keystone +/-

8

17. Menu

9

18. Brightness

19. HDMI

10

20. S-Video

11

21. Numbered keypad (for password input)

22. Freeze

232221

23. VGA

24. Laser Pointer

11

English

Installation

VGA1-IN / YPbPr /

VGA2-IN

/

SCART / YPbPr

VGA-OUT

S-VIDEO VIDEO

AUDIO-OUT

(VGA

1)

AUDIO1-IN

RS-232

USB

(VGA 2)

AUDIO2-IN

HDMI

R-J45

(S-VIDEO/VIDEO)

AUDIO3-IN

E62405SP

R

MOLEX

12V OUT

Due to the

difference in applications for each

country, some regions may

have different accessories.

(*) Optional

accessory

Connecting the Projector

Connect to Computer/Notebook

Audio Output

3

5

4

8 9

1

2

6

7

+12V Output

1....................................................................................................Power Cord

2.....................................................................................................VGA Cable

3..............................................................................................*Network Cable

4....................................................................................................*USB Cable

5...........................................................................................*DVI/HDMI Cable

6................................................................................................*RS232 Cable

7.........................................................................................*Audio Input Cable

8........................................................................................*VGA Output Cable

9......................................................................................*Audio Output Cable

12

English

Installation

VGA1-IN / YPbPr /

VGA2-IN

/

SCART / YPbPr

VGA-OUT

S-VIDEO VIDEO

AUDIO-OUT

(VGA

1)

AUDIO1-IN

RS-232

USB

(VGA

2)

AUDIO2-IN

HDMI

R-J45

(S-VIDEO/VIDEO)

AUDIO3-IN

E62405SP

R

12V OUT

Connect to Video Sources

DVD Player, Set-top Box,

HDTV receiver

1

2

7

910

4

S-Video Output

Composite Video Output

8

6

+12V Output

3

5

8

Due to the

difference in applications for each

country, some regions may

have different accessories.

(*) Optional

accessory

DVD Player, Set-top Box,

HDTV receiver

1....................................................................................................Power Cord

2.....................................................................................................VGA Cable

3................................................................................*Composite Video Cable

4.............................................................................................. *S-Video Cable

5................................................*15-Pin to 3 RCA Component/HDTV Adaptor

6.............................................................................*3 RCA Component Cable

7................................................................................... *SCART/VGA Adaptor

8.................................................................................*Audio Cable Jack/RCA

9..................................................................................................*HDMI Cable

10............................................................................................*Network Cable

13

English

Installation

When Power mode

POWER

?

(Standby) is set

to Eco (<1W), the VGA output, Audio pass-through

and RJ45 will be deactivated when

the projector is in

standby.

Powering the projector On / Off

Powering On the Projector

1. Remove the lens cap. 

2. Securely connect the power cord and signal cable. When

connected, the POWER/STANDBY LED will turn Amber.

3. Turn on the lamp by pressing “ ” button either on the top of the projector or on the remote. The POWER/STANDBY LED will now turn Green. 

The startup screen will display in approximately 10 seconds.

The rst time you use the projector, you will be asked to select the preferred language and power saving mode.

4. Turn on and connect the source that you want to display on the screen (computer, notebook, video player, etc). The projector will detect the source automatically. If not, push menu button and go to “OPTIONS”. Make sure that the “Source Lock” has been set to “Off”.

If you connect multiple sources at the same time, press the

“SOURCE” button on the control panel or direct source keys on the remote control to switch between inputs.

Turn on the

projector rst and

then select the signal sources.

2

Power

1

Lens Cap

14

English

Installation

Powering Off the Projector

1. Press the “ ” button on the remote control or on the control panel to turn off the projector.

The following message will be displayed on the screen.

Press the “ ” button again to conrm otherwise the

message will disappear after 15 seconds. When you press the “ ” button for the second time, the projector will display countdown timer and will shut down.

2. The cooling fans continue to operate for about 10 seconds

for cooling cycle and the POWER/STANDBY LED will Flash Green. When the POWER/STANDBY LED lights solid Amber, the projector has entered standby mode.

If you wish to turn the projector back on, you must wait

until the projector has completed the cooling cycle and has entered standby mode. Once in standby mode, simply

press “ ” button to restart the projector.

3. Disconnect the power cord from the electrical outlet and

the projector.

4. Do not turn on the projector immediately following a power

off procedure.

Contact the



nearest service center if the

projector displays these symptoms.

See pages 65-66 for more

information.

Warning Indicator

When the warning indicators (see below) come on,

the projector will automatically shutdown:

 “LAMP” LED indicator is lit red and if “POWER/STANDBY”

indicator ashes amber.

 “TEMP” LED indicator is lit red and if “POWER/STANDBY”

indicator ashes amber. This indicates the projector has overheated. Under normal conditions, the projector can be switched back on.

 “TEMP” LED indicator ashes red and if “POWER/STAND-

BY” indicator ashes amber.

Unplug the power cord from the projector, wait for 30 seconds

and try again. If the warning indicator light up again, please contact your nearest service center for assistance.

15

English

Installation

Adjusting the Projected Image

Adjusting the Projector’s Height

The projector is equipped with elevator feet for adjusting the image height.

1. Locate the adjustable foot you wish to modify on the

underside of the projector.

2. Rotate the adjustable ring clockwise to raise the projector or counter clockwise to lower it. Repeat with the remaining

feet as needed.

Tilt-Adjustment Feet

Tilt-Adjustment Ring

16

English

Installation

Width

Height

Diagonal

Top View

Side View

Projection Distance (D)

Screen

Screen (W)

Screen (H)

Offset (Hd)

POWER

?

Adjusting the Projector’s Zoom / Focus

You may turn the zoom ring to zoom in or out. To focus the image, rotate the focus ring until the image is clear.

XGA series: The projector will focus at distances from 4.92



to 39.4 feet (1.5 to 12.0 meters).

WXGA series: The projector will focus at distances from 3.93



to 32.8 feet (1.2 to 10.0 meters).

Adjusting Projection Image Size

XGA series: Projection Image Size from 36.3” to 362.0” (0.9



to 9.2 meters).

Zoom Ring

Focus Ring

WXGA series: Projection Image Size from 36.3” to 362.0”



(0.9 to 9.2 meters).

17

English

Installation

XGA

Diagonal length

(inch) size of

4:3 Screen

44.00 0.89 0.67 35.20 26.40 1.43 1.72 4.69 5.63 0.10 0.33

60.00 1.22 0.91 48.00 36.00 1.95 2.34 6.40 7.68 0.14 0.45

70.00 1.42 1.07 56.00 42.00 2.28 2.73 7.46 8.96 0.16 0.52

80.00 1.63 1.22 64.00 48.00 2.60 3.12 8.53 10.24 0.18 0.60

90.00 1.83 1.37 72.00 54.00 2.93 3.51 9.60 11.52 0.21 0.67

100.00 2.03 1.52 80.00 60.00 3.25 3.90 10.66 12.80 0.23 0.75

120.00 2.44 1.83 96.00 72.00 3.90 4.68 12.80 15.36 0.27 0.90

150.00 3.05 2.29 120.00 90.00 4.88 5.85 16.00 19.20 0.34 1.12

180.00 3.66 2.74 144.00 108.00 5.85 7.02 19.20 23.03 0.41 1.35

250.00 5.08 3.81 200.00 150.00 8.13 9.75 26.66 31.99 0.57 1.37

302.00 6.14 4.60 241.60 181.20 9.82 11.78 32.21 38.65 0.69 2.26

Screen Size W x H Projection Distance (D)

(m) (inch) (m) (feet)

Width Height Width Height wide tele wide tele (m) (feet)

 This table is for user’s reference only.

WXGA

Diagonal length

(inch) size of 16:10 Screen

44.00 0.95 0.59 37.40 23.23 1.20 1.50 3.94 4.92 0.07 0.24

60.00 1.29 0.81 50.79 31.89 1.70 2.00 5.58 6.56 0.10 0.33

70.00 1.51 0.94 59.45 37.01 1.90 2.30 6.23 7.54 0.12 0.38

80.00 1.72 1.08 67.72 42.52 2.20 2.60 7.22 8.53 0.13 0.44

90.00 1.94 1.21 76.38 47.64 2.50 3.00 8.20 9.84 0.15 0.49

100.00 2.15 1.35 84.65 53.15 2.80 3.30 9.18 10.82 0.17 0.55

120.00 2.58 1.62 101.57 63.78 3.30 4.00 10.82 13.12 0.20 0.66

150.00 3.23 2.02 127.17 79.53 4.10 5.00 13.45 16.40 0.25 0.82

180.00 3.88 2.42 152.76 95.28 5.00 6.00 16.40 19.68 0.30 0.98

250.00 5.38 3.37 211.81 132.68 6.90 8.30 22.63 27.22 0.42 1.37

302.00 6.50 4.07 255.91 160.24 8.30 10.00 27.22 32.80 0.50 1.66

Screen Size W x H Projection Distance (D)

(m) (inch) (m) (feet)

Width Height Width Height wide tele wide tele (m) (feet)

Offset (Hd)

 This table is for user’s reference only.

18

English

User Controls

POWER

?

Control Panel & Remote Control

Control Panel

Using the Control Panel

POWER

RE-SYNC

Enter

SOURCE

Menu

Four Directional

Select Keys

Keystone

HELP

Lamp LED Indicate the projector’s lamp status.

Temp LED Indicate the projector’s temperature status.

POWER/

STANDBY LED

Refer to the “Power On/Off the Projector” section on

pages 13-14.

Automatically synchronize the projector to the input

source.

Conrm your item selection.

Press “SOURCE” to select an input signal.

Press “Menu” to launch the on-screen display (OSD) menu. To exit OSD, Press “Menu” again.

Use to select items or make adjustments to your selection.

Use to adjust image distortion caused by tilting the projector. (±40 degrees)

Help Menu (refer to page 21).

?

Indicate the projector’s status.

19

English

User Controls

Remote Control

Using the Remote Control

Power

Laser

L Button

R Button

Page +

Page -

Enter / Help

Source

Re-SYNC

Four Directional

Select Keys

Keystone +/-

Volume +/-

Refer to the “Power On/Off the Projector”

section on pages 13-14.

Press to use laser pointer.

Mouse left click.

Mouse right click.

Use this button to page up.

Use this button to page down.

Conrm your item selection.

Help Menu (refer to page 21).

Press “Source” to select an input signal.

Automatically synchronizes the projector to

the input source.

Use to select items or make

adjustments to your selection.

Adjust image distortion caused by tilting the

projector.

Adjust to increase / decrease the volume.

Brightness

3D

Menu

HDMI

Adjust the brightness of the image.

Press the “3D” to turn the 3D OSD menu on/off.

Press “Menu” to launch the on-screen

display (OSD) menu. To exit OSD, press

“Menu” again.

Press “HDMI” to choose HDMI source.

20

English

User Controls

Using the Remote Control

Freeze

AV mute

S-Video Press “S-Video” to choose S-Video source.

VGA

Video

Press “Freeze” to pause the screen image. Press this button again to unlock.

Momentarily turns off/on the audio and

video.

Press “VGA” to choose VGA sources.

Press “Video” to choose Composite video

source.

21

English

User Controls

POWER

?

POWER

?

Using the HELP button

The HELP function ensures easy setup and operation.

Press the “?” button on the remote control or press the



“HELP” button on the control panel to open the Help Menu.

22

English

User Controls

Help menu button functions only when no input source



is detected.

Please refer to the

“Troubleshooting”

section on pages

50-54 for more

details.

If input source is detected and help button is pressed, the



following pages will appear to help diagnose any problems.

23

English

User Controls

24

English

User Controls

On-screen Display Menus

The Projector has multilingual On-screen Display menus that allow you to make image adjustments and change a variety of

settings. The projector will automatically detect the source.

How to operate

1. To open the OSD menu, press “Menu” on the Remote Control or

Projector Keypad.

2 When OSD is displayed, use

main menu. While making a selection on a particular page, press

or “Enter” key to enter sub menu.

3. Use

using key.

4. Select the next item to be adjusted in the sub menu and adjust as

described above.

5. Press “Enter” to conrm, and the screen will return to the main

menu.

6. To exit, press “MENU” again. The OSD menu will close and the

projector will automatically save the new settings.

keys to select the desired item and adjust the settings

keys to select any item in the

Main Menu

Sub Menu

Settings

25

English

User Controls

Main Menu Sub Menu Settings

Image

Display Mode

Brightness -50~50

Contrast -50~50

Sharpness 1~15

Color -50~50

Tint -50~50

Advanced Gamma Film / Video / Graphics / PC

BrilliantColor™ 0~10

Color Temp. Warm / Medium / Cold

Color Settings

Color Space AUTO / RGB / YUV

AUTO / RGB (0-255) / RGB (16-235) / YUV

Input Source VGA1 / VGA2 / Video / S-Video / HDMI

Exit

Display

Format 4:3 / 16:9 or 16:10 / LBX / Native / AUTO

4:3 / 16:9-1 / 16:9-II / Native / AUTO Edge Mask 0~10 Zoom -5~25 (80%~200%) H Image Shift -50~50 V Image Shift -50~50 V Keystone -40~40 Auto Keystone On / Off 3D 3D Off / DLP-Link / IR

3D Sync. Invert On / Off

Exit

Setup

Language

Screen Type 16:10 / 16:9

Projection

Menu Location

Signal Automatic On / Off

Phase (VGA) 0~31

Frequency (VGA) -5~5

H. Position (VGA) -5~5 V. Position (VGA) -5~5 Exit

ʳ

Security Security On / Off

Security Timer Month / Day / Hour Change Password

ʳ

Exit

Presentation / Bright / Movie / sRGB /

Blackboard / Classroom / User / 3D

#1

Red Gain / Green Gain / Blue Gain / Red

Bias / Green Bias / Blue Bias / Cyan /

Magenta / Yellow / Reset / Exit

#2

#3

#6

#4

English / Deutsch / Français / Italiano /

Español / Português / Svenska /

Nederlands / Norsk/Dansk / Polski /

Suomi / Ɋɭɫɫɤɢɣ / İȜȜȘȞȚțȐ / Magyar /

ýeština / γέΎϓ / ϲΑήϋ /᜗

᧯խ֮ʳ/ 亞󰪠խ֮ʳ/

ֲ

ء፿!0ᾂ᝖᱑ʳ/ ࡷࡎ࡙/ Türkçe

#3

#5

Menu Tree

26

English

User Controls

Main Menu Sub Menu Settings

Setup

Projector ID 0~99

Mute On / Off Volume 0~10 Audio Input Default / Audio1 / Audio2 / Audio3 Advanced Logo Optoma / Neutral / User

Logo Capture

Closed Captioning Off / CC1 / CC2

Exit

RS232 RS232 / Network Network Network State

DHCP IP Address

Subnet mask Gateway

DNS

Apply Yes / No

Exit

Wireless On / Off

Options

Source Lock On / Off High Altitude On / Off Information Hide On / Off Keypad Lock On / Off Background Color Black / Red / Blue / Green / White Advanced Direct Power On On / Off

Auto Power Off (min.) 0~180 Sleep Timer (min.) 0~995 Power Mode (Standby) Eco. / Active

Exit

Lamp Settings Lamp Hours

Lamp Reminder On / Off Brightness Mode Eco. / Bright Lamp Reset Yes / No

Exit

Reset

Please note that the on-screen display (OSD) menus vary according to the

signal type selected and the projector model you are using.

(#1) “Color” and “Tint” are only supported in Video mode.

(#2) For HDMI source only.

(#3) For WXGA model only. 16:9 or 16:10 depend on “Screen Type” setting.

(#4) “3D Sync Invert” is only available when 3D is enabled.

(#5) “Signal” is only supported in Analog VGA (RGB) signal.

(#6) For XGA model only.

27

English

User Controls

IMAGE

Display Mode

There are many factory presets optimized for various types of images.

Presentation: Good color and brightness from PC input.



Bright: Maximum brightness from PC input.



Movie: For home theater.



sRGB: Standardised accurate color.



Blackboard: This mode should be selected to achieve optimum



color settings when projecting onto a blackboard (green).

Classroom: This mode is recommended for projecting in a



classroom.

User: User’s settings.



3D: Recommended setting for 3D mode enabled. Any further ad-



justments by the user in 3D will be saved in this mode for further

use.

Brightness

Adjust the brightness of the image.

Press the to darken image.



Press the to lighten the image.



Contrast

The contrast controls the degree of difference between the lightest and darkest parts of the picture.

 Press the to decrease the contrast.

Press the to increase the contrast.



28

English

User Controls

Sharpness

Adjust the sharpness of the image.

 Press the to decrease the sharpness.  Press the to increase the sharpness.

Color

“Color” and “Tint”

functions are only

supported under

Video mode.

Adjust a video image from black and white to fully saturated color.

 Press the to decrease the amount of color in the image  Press the to increase the amount of color in the image.

Tint

Adjust the color balance of red and green.

 Press the to increase the amount of green in the image.  Press the to increase the amount of red in the image.

29

English

User Controls

IMAGE | Advanced

Gamma

This allows you to choose a degamma table that has been ne-tuned to bring out the best image quality for the input.

 Film: for home theater.

Video: for video or TV source.



Graphics: for image source.



 PC: for PC or computer source.

BrilliantColor™

This adjustable item utilizes a new color-processing algorithm and system level enhancements to enable higher brightness while providing true, more vibrant colors in picture. The range is from “0” to “10”. If you prefer a stronger enhanced image, adjust toward the maximum setting. For a smoother, more natural image, adjust toward the minimum setting.

Color Temp

If set to cold temperature, the image looks more blue. (cold image) If set to warm temperature, the image looks more red.

(warm image)

Color Settings

Press into the next menu as below and then use or to

select item.

 Red/Green/Blue/Cyan/Magenta/Yellow: Use or to select

Red, Green, Blue, Cyan, Magenta and Yellow Colors.

 Reset: Choose “Yes” to return the factory default settings for

color adjustments.

30

English

User Controls

Color Space

Select an appropriate color matrix type from AUTO, RGB or YUV.

Input Source

Use this option to enable / disable input sources. Press to enter the sub menu and select which sources you require. Press “Enter” to finalize the selection. The projector will not search for inputs that

are not selected.

31

English

User Controls

DISPLAY

Format

Use this function to choose your desired aspect ratio.

XGA

4:3: This format is for 4×3 input sources.



16:9-I: This format is for 16×9 input sources, like HDTV and



DVD enhanced for Wide screen TV. (576i/p)

16:9-II: This format is for 16×9 input sources, like HDTV and



DVD enhanced for Wide screen TV. (480i/p)

Native: This format displays the original image without any



scaling.

AUTO: Automatically selects the appropriate display format.



When input is 4:3, the image is displayed as 4:3. When input is 16:9 above, the image is displayed as 16:9- I

Aspect ratio

(source detected)

4:3 1024 x 768 center

16:9-I 1024 x 576 center

16:9-II 854 x 480 center

Native

Resize image (XGA)

No resize image, 1:1 mapping and

centered. This format shows the

original image without scaling.

32

English

User Controls

WXGA

4:3: This format is for 4×3 input sources.



16:9: This format is for 16×9 input sources, like HDTV and DVD



enhanced for Wide screen TV.

16:9 or 16:10

depend on “Screen Type” setting.

16:10: This format is for 16×10 input sources, like widescreen



laptops.

LBX: This format is for non-16x9, letterbox source and for users



who use external 16x9 lens to display 2.35:1 aspect ratio using

full resolution.

Native: This format displays the original image without any



scaling.

AUTO: Automatically selects the appropriate display format.



16:10 Screen 480i/p 576i/p 1080i/p 720p PC

4:3 1066 x 800 center

16:10 1280 x 800 center

LBX

Native

1280 x 960 center, then get the central 1280 x 800 image

1:1 mapping

centered.

to display

1:1 map-

ping display

1280 x 800

1280 x 720

center

1:1

mapping

centered.

16:9 Screen 480i/p 576i/p 1080i/p 720p PC

4:3 960 x 720 center

16:9 1280 x 720 center

LBX

Native

1280 x 960 center, then get the central 1280 x 720 image

1:1 mapping

centered.

to display

1:1 map-

ping display

1280 x 720

center

1:1

mapping

centered.

33

English

User Controls

Each I/O has

different setting of “Edge Mask”.

“Edge Mak” and

“Zoom” can’t work at same time.

Edge Mask

Edge mask function removes the noise in a video image. Edge mask the image to remove video encoding noise on the edge of video source.

Zoom

 Press the to reduce the size of an image.

 Press the to magnify an image on the projection screen.

H Image Shift

Shift the projected image position horizontally.

V Image Shift

Shift the projected image position vertically.

V Keystone

Press the or to adjust image distortion vertically. If the image looks trapezoidal, this option can help make the image rectangular.

Auto Keystone

Automatically adjusts vertical image distortion.

34

English

User Controls

DISPLAY | 3D

3D

Off: Select “Off” to turn 3D settings off for 3D images.



DLP Link: Select “DLP Link” to use optimized settings for DLP



“IR” options may

vary according to model.

“3D Sync Invert” is

only available when

3D is enabled and

this mode 3D is for DLP link glass only.

Compatible 3D

source, 3D content and active shutter

glasses are required for 3D viewing.

Link 3D images.

IR: Select “IR” to use optimized settings for IR-based 3D



images.

3D Sync. Invert

Press the “On” to invert left and right frame contents.



Press the “Off” for default frame contents.



35

English

User Controls

Rear-Desktop and

Rear-Ceiling are

to be used with a

translucent screen.

SETUP

Language

Choose the multilingual OSD menu. Press or into the sub menu and then use the or key to select your preferred

language. Press “Enter” to nalize the selection.

“Screen Type” is for

WXGA only.

Screen Type

Choose the screen type from16:10 or 16:9.

Projection

 Front-Desktop

This is the default selection. The image is projected straight on

the screen.

 Rear-Desktop

When selected, the image will appear reversed.

 Front-Ceiling

36

English

User Controls

When selected, the image will turn upside down.



Rear-Ceiling

When selected, the image will appear reversed in upside down

position.

Menu Location

Choose the menu location on the display screen.

Projector ID

ID denition can be set up by menu (range 0~99), and allow user control an individual projector by RS232. Refer to page 60-63 for the complete list of RS232 commands.

Mute

Choose the “On” to turn mute on.



Choose the “Off” to turn mute off.



Volume

 Press the to decrease the volume.

 Press the to increase the volume.

Audio Input

The default audio settings are on the back panel of the projector. Use this option to reassign any of the Audio Inputs (1 ,2 or 3) to the current image source. Each Audio input can be assigned to more than one video source.

Audio 1: VGA 1.



Audio 2: VGA 2.



Audio 3: S-Video/Video.



Default: Set Input back to default video source.



37

English

User Controls

SETUP

RS232

RS232: Allow RS232 control of an individual projector.



Network: Allow projector control via web browser (Internet



Wireless

Choose the “On” to turn on the Wireless.

(Default setting)

Explorer) using the network.

“Wireless” is only-

functional with VGA

connector.

Warning:

Wired VGA will not

function and the

projector maybe shut down if Wire-

less is turned on.

38

English

User Controls

SETUP | Signal

(RGB)

“Signal” is only

supported in Analog VGA (RGB) signal.

Automatic

Automatically selects the signal. If you use this function, the Phase, frequency items are grayed out, and if Signal is not automatic, the phase, frequency items will appear for user to manually tune and saved in settings after that for next time projector turns

off and on again.

Phase

Synchronize the signal timing of the display with the graphic card. If the image appears to be unstable or ickers, use this function to

correct it.

Frequency

Change the display data frequency to match the frequency of your computer’s graphic card. Use this function only if the image appears to icker vertically.

H. Position

Press the to move the image left.



Press the to move the image right.



V. Position

Press the to move the image down.



Press the to move the image up.



39

English

User Controls

SETUP | Security

Password default

value is “1234” (rst time).

Security

On: Choose “On” to use security verication when the turning



Security Timer

Change Password



on the projector.

Off: Choose “Off” to be able to switch on the projector without

password verication.

Use this function to set the how long (Month/Day/Hour) the projector can be used. Once this time has elapsed you will be requested to enter your password again.

First time:

1. Press “ ” to set the password.

2. The password has to be 4 digits.

3. Use number button on the remote to enter your new password and then press “ ” key to conrm your password.

Change Password:

1. Press “ ” to input old password.

2. Use number button to enter current password and then

press “ ” to conrm.

3. Enter new password (4 digits in length) using the number

buttons on the remote, then press “ ” to conrm.

4. Enter new password again and press “ ” to conrm.

40

English

User Controls

If the incorrect password is entered 3 times, the projector will



automatically shut down.

If you have forgotten your password, please contact your local



ofce for support.

41

English

User Controls

SETUP | Advanced

Logo

Use this function to set the desired startup screen. If changes are

made they will take effect the next time the projector is powered

on.

Optoma: The default startup screen.



Neutral: Neutral startup screen.



User: Use stored picture from “Logo Capture” function.



For successful logo

capture, please ensure that the input signal does not ex-

ceed the projector’s

native resolution. (XGA:1024x768 or WXGA:1280x800).

Logo Capture

Press to capture an image of the picture currently displayed

on screen.

Closed Captioning

Use this function to set the desired startup screen. If changes are

made they will take effect the next time the projector is powered

on.

Off: select “off” to turn off the closed captioning feature.



CC1:CC1 language: American English.



CC2:CC2 language (depending on the TV channel of the



user):Spanish, French, Portuguese, German, Danish.

42

English

User Controls

SETUP | Network

Network State

Display the network connection status.

DHCP

Use this function to select your desired startup screen. If you change the setting from one to another, when you exit the OSD menu, the new setting will take effect on next open.

On: Assign an IP address to the projector from an external



DHCP server automatically.

Off: Assign an IP address manually.



IP Address

Select an IP address.

Subnet Mask

Select subnet mask number.

Gateway

Select the default gateway of the network connected to the

projector.

DNS

Select DNS number.

Apply

Press “ ” and then choose “Yes” to apply the selection.

43

English

User Controls

How to use web browser to control your projector

1. Turn on DHCP to allow the DHCP server to automatically assign an IP, or manually enter the required network information.

2. Then choose apply and press “

” button to complete the conguration process.

3. Open your web browser and type in the projector’s IP address from the OSD LAN screen. The following web page will display as below:

When you used the projector IP ad-

dress, you will can not link to your

service server.

4. The crestron control settings can be found in the [tools] tab.(see picture)

Please note, each eld can only contain a limited number of characters, as shown in the table below. (spaces and the other punctuation included):

Category Item

IP Address 15

Crestron Control

Projector

Network Conguration

User Password

Admin Password

IP ID 2

Port 5

Projector Name 10

Location 9

Assigned To 9

DHCP (Enabled) (N/A)

IP Address 15

Subnet Mask 15

Default Gateway 15

DNS Server 15

Enabled (N/A)

New Password 15

Conrm 15

Enabled (N/A)

New Password 15

Conrm 15

Input-Length

(characters)

44

English

User Controls

When making a direct connection from your computer to the projector

Step 1: Find an IP Address (192.168.0.100) from LAN function of projector.

Step 2: Select apply and press “Enter” button to submit function or press “menu” key to

exit.

Step 3: To open Network Connections,

click Start, click Control Panel, click Network and Internet

Connections, and then click Network Connections. Click the

connection you want to congure,

and then, under Network Tasks

, click Change settings of

this connection.

Step 4: On the General tab, under

This connection uses the following items, click Internet Protocol (TCP/IP), and then click

“Properties.”

Step 5: Click Use the following IP

address, and type in as below:

1) IP address: 192.168.0.100

2) Subnet mask: 255.255.255.0

3) Default gateway:192.168.0.254

Step 6: To open Internet Options, click

IE web browser, click Internet Options, click the Connections tab and click “LAN Settings...”

Step 7: The Local Area Network (LAN)

Setting dialog box appears, In the Proxy Server area, cancel the Use a proxy server for your LAN check box., then click “OK” button

twice.

Step 8: Open your IE and type in the IP

address of 192.168.0.100 in the URL then press “Enter” key.

45

English

User Controls

Crestron RoomView Control Tool

Crestron RoomView™ provides a central monitoring station for 250+ control systems on a single Ethernet network (more are possible, the number depends on the combination of IP ID and IP address). Crestron RoomView monitors each projector, including projector’s online status, system power, lamp life, network setting and hardware faults, plus any custom attribute as dened by the Administrator. The Administrator can add, delete, or edit room information, contact information and events, which are logged automatically by the software for all users. (Operation UI as following image)

1. Main Screen

2. Edit Room

Crestron Room-

View function support is dependent

on models.

46

English

User Controls

3. Edit Attribute

4. Edit Event

For more information, please visit http://www.crestron.com & www.crestron.com/getroomview.

47

English

User Controls

With dust lter

installed, High

Altitude mode must

be turned on. Dust

lter is Optional and may not be required in some regions.

OPTIONS

Source Lock

On: The projector will only search current input connection.



Off: The projector will search for other signals if the current



High Altitude

When “On” is selected, the fans will spin faster. This feature is useful in high altitude areas where the air is thin.

Information Hide

 

input signal is lost.

On: Choose “On” to hide the info message.

Off: Choose “Off” to show the “searching” message.

To turn off the key-

pad lock, press and hold “Enter” key on

top of the projector for 5 seconds.

Keypad Lock

When the keypad lock function is “On”, the control panel will be locked however, the projector can be operated by the remote control. By selecting “Off”, you will be able to reuse the control

panel.

Background Color

Use this feature to display a “Black”, “Red”, “Blue”, “Green” or “White”, screen when no signal is available.

Reset

Choose “Yes” to return the display parameters on all menus to the factory default settings.

48

English

User Controls

OPTIONS |

Advanced

Direct Power On

Choose “On” to activate Direct Power mode. The projector will automatically power on when AC power is supplied, without pressing the “ ” key on the projector control panel or on the remote control.

Auto Power Off (min)

Sets the countdown timer interval. The countdown timer will start, when there is no signal being sent to the projector. The projector will automatically power off when the countdown has nished (in minutes).

When Power mode

(Standby) is set to

Eco. (<1W), the VGA output, Audio pass-through

and RJ45 will be deactivated when

the projector is in

standby.

Sleep Timer (min)

Sets the countdown timer interval. The countdown timer will start, with or without a signal being sent to the projector. The projector will automatically power off when the countdown has nished (in minutes).

Power Mode (Standby)

Eco.: Choose “Eco.” to save power dissipation further < 1W.



Active: Choose “Active” to return to normal standby and the



VGA out port will be enabled.

49

English

User Controls

Lamp Settings

When ambient tem-

perature is over 40°C in operating, the

projector will switch to [Eco.] automatically.

OPTIONS |

Lamp Hours

Display the projection time.

Lamp Reminder

Choose this function to show or to hide the warning message when the changing lamp message is displayed. The message will appear 30 hours before suggested replacement

of lamp.

Brightness Mode

Eco.: Choose “Eco.” to dim the projector lamp which will lower



power consumption and extend the lamp life.

BRIGHT: Choose “BRIGHT” to increase the brightness.



Lamp Reset

Reset the lamp hour counter after replacing the lamp.

50

English

Appendices

Troubleshooting

If you experience a problem with your projector,

please refer to the following information. If a problem persists, please contact your local reseller or service center.

No image appears on-screen

Ensure all the cables and power connections are correctly and



securely connected as described in the “Installation” section.

Ensure all the pins of connectors are not bent or broken.



Check if the projection lamp has been securely installed. Please



refer to the “Replacing the lamp” section.

Make sure you have removed the lens cap and the projector is



switched on.

Ensure that the “AV mute” feature is not turned on.



Partial, scrolling or incorrectly displayed image



Press “Re-SYNC” on the remote.

If you are using a PC:



For Windows 95, 98, 2000, XP, Windows 7:

1. Open the “My Computer” icon, the “Control Panel” folder, and then double click on the “Display” icon.

2. Select the “Settings” tab.

3. Verify that your display resolution setting is lower than or equal

to UXGA (1600 × 1200).

4. Click on the “Advanced Properties” button.

If the projector is still not projecting the whole image, you will also need to change the monitor display you are using. Refer to the following steps.

5. Verify the resolution setting is lower than or equal to UXGA

(1600 × 1200).

6. Select the “Change” button under the “Monitor” tab.

51

English

Appendices

7. Click on “Show all devices”. Next, select “Standard monitor types” under the SP box; choose the resolution mode you need

under the “Models” box.

8. Verify that the resolution setting of the monitor display is lower than or equal to UXGA (1600 × 1200).

If you are using a Notebook:



1. First, follow the steps above to adjust resolution of the computer.

2. Press the appropriate keys listed below for your notebook manufacturer to send signal out from notebook to projector. Example: [Fn]+[F4]

Acer  [Fn]+[F5] Asus  [Fn]+[F8] Dell  [Fn]+[F8]

Gateway  [Fn]+[F4]

Mac Apple: System Preference  Display  Arrangement  Mirror display

If you experience difculty changing resolutions or your monitor



freezes, restart all equipment including the projector.

The screen of the Notebook or PowerBook computer is not

IBM/Lenovo  [Fn]+[F7] HP/Compaq  [Fn]+[F4]

NEC  [Fn]+[F3] Toshiba  [Fn]+[F5]

displaying your presentation

If you are using a Notebook PC



Some Notebook PCs may deactivate their own screens when a second display device is in use. Each has a different way to be reactivated. Refer to your computer’s manual for detailed information.

Image is unstable or ickering

Use “Phase” to correct it. See page 38 for more information.



Change the monitor color setting on your computer.



Image has vertical ickering bar

Use “Frequency” to make an adjustment. See page 38 for more



information.

Check and re-congure the display mode of your graphic card to



make it compatible with the projector.

52

English

Appendices

Image is out of focus

Make sure the lens cap is removed.



Adjust the Focus Ring on the projector lens.



Make sure the projection screen is between the required distance.



See page 16.

The image is stretched when displaying 16:9 DVD title

When you play anamorphic DVD or 16:9 DVD, the projector will



show the best image when the projector display mode is set to 16:9 in the OSD.

If you play 4:3 format DVD titles, please change the format to 4:3



in the projector OSD.

If the image is still stretched, you will also need to adjust the



aspect ratio by referring to the following:

Please setup the display format as 16:9 (wide) aspect ratio type



on your DVD player.

Image is too small or too large

Move the projector closer to or further from the screen.



Press “Menu” button on the remote control or projector panel, go



to “DISPLAY  Format” and try the different settings.

Use of Keystone

is not recommended.

Image has slanted sides

If possible, reposition the projector so that it is horizontally



centered on the screen and below the bottom of the screen.

Press “Keystone +/-” button on the remote control or press



“ / ” on the projector panel, until the sides are vertical.

Image is reversed

Select “SETUP  Projection” from the OSD and adjust the



projection direction.

53

English

Appendices

The projector stops responding to all controls

If possible, turn off the projector, then unplug the power cord and



wait at least 60 seconds before reconnecting power.

Check that “Keypad Lock” is not activated by trying to control the



projector with the remote control.

Lamp burns out or makes a popping sound

When the lamp reaches its end of life, it will burn out and may



make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the “Replacing the Lamp” section on

pages 55-56.

LED lighting message

Steady light 

No light 

Message

Standby State (Input power cord)

Power on (Warming)

Lamp lighting Green

Power off (Cooling)

Error (Over Temp.)

Error (Fan fail)

Error (Lamp fail)

＊ POWER/STANDBY LED be ON when OSD appears, be OFF when OSD disappears.

POWER/STAND-

BY LED

(Green/Amber) (Red) (Red)

Amber

Flashing

Green

Flashing

Green

Flashing

Amber

Flashing

Amber

Flashing

Amber

Temp-LED

Flashing

Lamp-LED

54

English

Appendices

On Screen Messages

Temperature warning:



Fan failed:



Lamp warning:



Out of display range:



If the remote control does not work

Check the operating angle of the remote control is within ±15°



both horizontally and vertically of one of the IR receivers on the

projector.

Make sure there are not any obstructions between the remote



control and the projector. Move to within 7 m (±0°) of the projector.

Make sure the batteries are inserted correctly.



Replace batteries if they are exhausted.



55

English

Appendices

Replacing the lamp

The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message.

When you see this message, please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp.

Warning: If ceiling mounted, please use caution when

opening the lamp access panel. It is recommended to wear safety glasses if changing the bulb when ceiling mounted. “Caution must be used to prevent any loose parts from fall-

ing out of projector.”

Warning: Lamp compartment may be hot! Allow it to cool

down before changing the lamp!

Warning: To reduce the risk of personal injury, do not drop

the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.

56

English

Appendices

1

2

3

4

The screws on the

lamp cover and the lamp cannot be removed.

The projector

cannot be turned

on if the lamp

cover has not been

placed back on the

projector.

Do not touch the

glass area of the

lamp. Hand oil can cause the lamp to shatter. Use a dry

cloth to clean the

lamp module if it was accidentally

touched.

Lamp Replacement Procedure:

1. Switch off the power to the projector by pressing the “ ” button.

2. Allow the projector to cool down for at least 30 minutes.

3. Disconnect the power cord.

4. Unscrew the two screws on the cover. 1

5. Lift up and remove the cover. 2

6. Unscrew the two screws on the lamp module. 3

7. Lift up the lamp handle and remove the lamp module slowly and carefully. 4

To replace the lamp module, reverse the previous steps.

8. Turn on the projector and use “Lamp Reset” after the lamp module is

Lamp Reset: (i) Press “Menu”  (ii) Select “OPTIONS”  (iii) Select

replaced.

“Lamp Settings”  (iv) Select “Lamp Reset”  (v) Select “Yes”.

57

English

Appendices

For widescreen

resolution (WXGA), the

compatibility

support is dependent on

Notebook/PC models.

120Hz input

signals may be

dependent on graphics cards support.

Please note that

using resolutions other than native 1024 x 768 (XGA

model), 1280

x 800 (WXGA

model) may result in some loss of image clarity.

Compatibility Modes

Computer Compatibility



Mode Resolution

VGA 640 × 350 70 31.50

VGA 640 × 350 85 37.90

VGA 640 × 400 85 37.90

VGA 640 × 480 60 31.50

VGA 640 × 480 67 -

VGA 640 × 480 72 37.90

VGA 640 × 480 75 37.50

VGA 720 × 400 70 31.50

VGA 720 × 400 85 37.90

SVGA 800 × 600 56 35.20

SVGA 800 × 600 60 37.90

SVGA 800 × 600 72 48.10

SVGA 800 × 600 75 46.90

SVGA 800 × 600 120 -

832 × 624 75 -

XGA 1024 × 768 60 48.40

XGA 1024 × 768 70 56.50

XGA 1024 × 768 75 60.00

XGA 1024 × 768 120 -

1152 × 870 75 -

HD 1280 x 720 60 45.00

HD 1280 x 720 120 -

WXGA-800 1280 x 800 60 -

SXGA 1280 x 1024 60 64.00

1366 x 768 60 -

1440 x 900 60 55.935

SXGA+ 1400 x 1050 60 -

UXGA 1600 × 1200 60 75.00

1680 x 1050 60 -

HDTV 1920 x 1080 30 33.80

Analog/Digital

V-Sync (Hz) H-Sync (KHz)

58

English

Appendices

Computer Compatibility



Mode Resolution V-Sync (Hz) H-Sync (KHz)

MAC LC 13” 640 × 480 66.66 34.98

MAC II 13” 640 × 480 66.68 35.00

MAC 16” 832 × 624 74.55 49.73

MAC 19” 1024 × 768 75 60.24

MAC 1152 × 870 75.06 68.68

MAC G4 640 × 480 60 31.35

i MAC DV 1024 × 768 75 60.00

i MAC DV 1152 × 870 75 68.49

Video Compatibility



NTSC M (3.58MHz), 4.43 MHz

PAL B, D, G, H, I, M, N

SECAM B, D, G, K, K1, L

SDTV 480i/p@60Hz, 576i/p@50Hz

HDTV 720p@50Hz/60Hz, 1080i@50Hz/60Hz,

1080p@24Hz/25Hz/30Hz/50Hz/60Hz

59

English

Appendices

RS232 shell is

12345

6789

grounded.

RS232 Commands and Protocol Function List

RS232 Pin Assignments

Pin no.

1 N/A

2 RXD

3 TXD

4 N/A

5 GND

6 N/A

7 N/A

8 N/A

9 N/A

Spec.

(from projector side)

60

English

Appendices

Optoma EW615i RS232 Command Table.

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Baud Rate : 9600 Note : There i s a <CR> after all ASCII commands Data Bits: 8 0D is the HEX code for <CR> in ASCII code Parity: None Stop Bits: 1 Flow Control : None UART16550 FIFO: Disable Projector Return (Pass): P Projector Return (Fail): F XX=01ˀ99 , projector's ID, XX=00 is for all projectors

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

SEND to projecto r

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

232 ASCII Code HEX Code Function Description

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX00 1 7E 30 30 30 30 20 31 0D Power ON ~XX00 0 7E 30 30 30 30 2 0 30 0D Power OFF (0/2 for backward compatible) ~XX00 1 ~nnnn 7E 30 30 30 30 20 31 20 a 0D Power ON with Password ~nnnn = ~0000 (a=7E 30 30 30 30)

~9999 (a=7E 39 39 39 39)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX01 1 7E 30 30 30 31 20 31 0D Resync ~XX02 1 7E 30 30 30 32 20 31 0D AV Mute On ~XX02 0 7E 30 30 30 32 20 3 0 0D Off (0/2 for backward compatible) ~XX03 1 7E 30 30 30 33 2 0 31 0D Mute On ~XX03 0 7E 30 30 30 33 20 3 0 0D Off (0/2 for backward compatible) ~XX04 1 7E 30 30 30 34 20 3 1 0D Freeze ~XX04 0 7E 30 30 30 34 20 30 0D Unfreeze (0/2 for backward compatible) ~XX05 1 7E 30 30 30 35 2 0 31 0D Zoom Plus ~XX06 1 7E 30 30 30 36 2 0 31 0D Zoom Minus ~XX12 1 7E 30 30 31 32 2 0 31 0D Direct Sour ce Commands HDMI ~XX12 5 7E 30 30 31 32 20 35 0D VGA 1 ~XX12 6 7E 30 30 31 32 20 36 0D VGA 2 ~XX12 8 7E 30 30 31 32 2 0 38 0D VGA 1 Component ~XX12 9 7E 30 30 31 32 20 3 9 0D S-Video ~XX12 10 7E 30 30 31 32 2 0 31 30 0D Video ~XX12 12 7E 30 30 31 32 2 0 31 33 0D VGA 2 SCART ~XX12 13 7E 30 30 31 32 20 31 33 0D VGA 2 Component

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX20 1 7E 30 30 32 30 20 31 0D Display Mode Presenta tion ~XX20 2 7E 30 30 32 30 2 0 32 0D Bright ~XX20 3 7E 30 30 32 30 2 0 33 0D Movie ~XX20 4 7E 30 30 32 30 20 34 0D sRGB ~XX20 5 7E 30 30 32 30 20 3 5 0D User ~XX20 7 7E 30 30 32 30 20 37 0D Blackboard ~XX20 8 7E 30 30 32 30 2 0 38 0D Classroom ~XX20 9 7E 30 30 32 30 2 0 39 0D 3D

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX21 n 7E 30 30 32 31 20 a 0 D Brightness n = 0 (a=30) ~ 100 (a=31 30 30) ~XX22 n 7E 30 30 32 32 20 a 0 D Contrast n = 0 (a=30) ~ 100 (a=31 30 30) ~XX23 n 7E 30 30 32 33 2 0 a 0D Sharpness n = 0 (a=30) ~ 15 (a=33 31)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX24 n 7E 30 30 32 34 20 a 0D Color Settings Red Gain n = -50 (a=2D 35 30) ~ 50 (a=35 30) ~XX25 n 7E 30 30 32 35 20 a 0D Green Gain n = -50 (a=2D 35 3 0) ~ 50 (a=35 30) ~XX26 n 7E 30 30 32 36 20 a 0D Blue Gain n = -50 (a=2D 35 30) ~ 50 (a=35 30) ~XX27 n 7E 30 30 32 37 20 a 0D Red Bias n = -50 (a=2D 35 3 0) ~ 50 (a=35 30) ~XX28 n 7E 30 30 32 38 20 a 0D Green Bias n = -50 (a=2D 35 30) ~ 50 (a=35 30) ~XX29 n 7E 30 30 32 39 20 a 0D Blue Bias n = -50 (a=2D 35 30) ~ 50 (a=35 30) ~XX30 n 7E 30 30 33 30 20 a 0D Cyan n = -50 (a=2D 35 30) ~ 50 (a=35 30) ~XX31 n 7E 30 30 33 31 20 a 0D Yellow n = -50 (a=2D 35 30) ~ 50 (a=35 30) ~XX32 n 7E 30 30 33 32 20 a 0D Magenta n = -50 (a=2D 35 30) ~ 50 (a=35 30) ~XX33 1 7E 30 30 33 33 20 31 0D Reset

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX34 n 7E 30 30 33 34 2 0 a 0D Brill iantColorTM n = 0 (a=30) ~ 10 (a=31 30) ~XX35 1 7E 30 30 33 35 2 0 31 0D Gamma Film ~XX35 2 7E 30 30 33 35 2 0 32 0D Video ~XX35 3 7E 30 30 33 35 2 0 33 0D Graphics ~XX35 4 7E 30 30 33 35 2 0 34 0D PC

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX36 1 7E 30 30 33 36 20 31 0D Color Temp. Warm ~XX36 2 7E 30 30 33 36 2 0 32 0D Medium ~XX36 3 7E 30 30 33 36 2 0 33 0D Cold ~XX37 1 7E 30 30 33 37 2 0 31 0D Color Spa ce Auto ~XX37 2 7E 30 30 33 37 2 0 32 0D RGB\ RGB(0-255) ~XX37 3 7E 30 30 33 37 2 0 33 0D YUV ~XX37 4 7E 30 30 33 37 2 0 34 0D RGB(16-235)

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

RS232 Protocol Function List

Baud Rate : 9600 Data Bits: 8

1. There is a <CR> after all ASCII commands.

2. 0D is the HEX code

for <CR> in ASCII

code.

Parity: None Stop Bits: 1 Flow Control : None UART16550 FIFO: Disable Projector Return (Pass): P Projector Return (Fail): F

XX=00-99, projector's ID, XX=00 is for all projectors

61

English

Appendices

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX44 n 7E 30 30 34 34 2 0 a 0D Color (Saturation) n = 0 (a=30) ~ 100 (a=31 30 30) ~XX45 n 7E 30 30 34 35 2 0 a 0D Tint n = 0 (a=30) ~ 100 (a=31 3 0 30)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------(WXGA) ~XX60 1 7E 30 30 36 30 20 31 0D Format 4:3 ~XX60 2 7E 30 30 36 30 2 0 32 0D 16:9/16:10 ~XX60 5 7E 30 30 36 30 20 33 0D LBX ~XX60 6 7E 30 30 36 30 2 0 36 0D Native ~XX60 7 7E 30 30 36 30 2 0 37 0D Auto

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------(XGA) ~XX60 1 7E 30 30 36 30 20 31 0D Format 4:3 ~XX60 2 7E 30 30 36 30 2 0 32 0D 16:9-I ~XX60 5 7E 30 30 36 30 2 0 33 0D 16:9-II ~XX60 6 7E 30 30 36 30 2 0 36 0D Native ~XX60 7 7E 30 30 36 30 2 0 37 0D Auto

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX61 n 7E 30 30 36 31 2 0 a 0D Edg emask n = 0 (a=30) ~ 10 (a=31 30) ~XX62 n 7E 30 30 36 32 20 a 0D Zoom n = -5 (a=2D 35) ~ 25 (a=32 35) ~XX63 n 7E 30 30 36 33 20 a 0D H Image Shift n = -50 (a=2 D 35 30) ~ +50 (a=35 30) ~XX64 n 7E 30 30 36 34 20 a 0D V Image Shift n = -50 (a=2 D 35 30) ~ +50 (a=35 30) ~XX66 n 7E 30 30 36 36 20 a 0D V Keystone n = -40 (a=2D 34 30) ~ 40 (a=34 30) ~XX69 1 7E 30 30 36 39 20 31 0D Auto Keystone On ~XX69 0 7E 30 30 36 39 20 3 0 0D Auto Keystone Off ~XX230 3 7E 30 30 32 33 30 20 31 0D 3D Mode IR ~XX230 1 7E 30 30 32 33 3 0 20 31 0D 3D Mode DLP-Link ~XX230 0 7E 30 30 32 33 30 20 30 0D 3D Mode Off ~XX231 1 7E 30 30 32 33 31 20 31 0D 3D Sync Invert On ~XX231 0 7E 30 30 32 33 31 20 30 0D 3D Sync Invert Off

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX70 1 7E 30 30 37 30 2 0 31 0D Language English ~XX70 2 7E 30 30 37 30 20 32 0D German ~XX70 3 7E 30 30 37 30 2 0 33 0D French ~XX70 4 7E 30 30 37 30 20 3 4 0D Italian ~XX70 5 7E 30 30 37 30 2 0 35 0D Spanish ~XX70 6 7E 30 30 37 30 2 0 36 0D Portuguese ~XX70 7 7E 30 30 37 30 2 0 37 0D Polish ~XX70 8 7E 30 30 37 30 2 0 38 0D Dutch ~XX70 9 7E 30 30 37 30 2 0 39 0D Swedish ~XX70 10 7E 30 30 37 30 2 0 31 30 0D Norwegian/Danish ~XX70 11 7E 30 30 37 30 20 31 31 0D Finnish ~XX70 12 7E 30 30 37 30 2 0 31 32 0D Greek ~XX70 13 7E 30 30 37 30 2 0 31 33 0D Traditional Chinese ~XX70 14 7E 30 30 37 30 20 31 34 0D Simplified Chinese ~XX70 15 7E 30 30 37 30 2 0 31 35 0D Japanese ~XX70 16 7E 30 30 37 30 2 0 31 36 0D Korean ~XX70 17 7E 30 30 37 30 2 0 31 37 0D Russian ~XX70 18 7E 30 30 37 30 20 31 38 0D Hungarian ~XX70 19 7E 30 30 37 30 20 31 39 0D Czechoslovak ~XX70 20 7E 30 30 37 30 20 32 30 0D Arabic ~XX70 21 7E 30 30 37 30 20 32 31 0D Thai ~XX70 22 7E 30 30 37 30 20 32 32 0D Turkish ~XX70 23 7E 30 30 37 30 2 0 32 33 0D Farsi

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX71 1 7E 30 30 37 31 2 0 31 0D Projection Front-Desktop ~XX71 2 7E 30 30 37 31 20 3 2 0D Rear-Desktop ~XX71 3 7E 30 30 37 31 2 0 33 0D Front-Ceiling ~XX71 4 7E 30 30 37 31 20 34 0D Rear-Ceiling

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX72 1 7E 30 30 37 32 2 0 31 0D Menu Locat ion Top Left ~XX72 2 7E 30 30 37 32 2 0 32 0D Top Right ~XX72 3 7E 30 30 37 32 2 0 33 0D Centre ~XX72 4 7E 30 30 37 32 2 0 34 0D Bottom Left ~XX72 5 7E 30 30 37 32 20 35 0D Bottom Right

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX90 1 7E 30 30 39 31 2 0 31 0D Screen Type 16:10 ~XX90 0 7E 30 30 39 31 20 30 0D 16:9

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX91 n 7E 30 30 39 31 20 a 0D Signa l Automatic n=0 Off; n=1 On ~XX73 n 7E 30 30 37 33 20 a 0D Frequency n = -5 (a=2D 35) ~ 5 ( a=35) By signal ~XX74 n 7E 30 30 37 34 20 a 0D Phase n = 0 (a=30) ~ 31 (a=33 31) By signal ~XX75 n 7E 30 30 37 35 20 a 0D H. Position n = -5 (a=2D 35) ~ 5 (a=35) By timing ~XX76 n 7E 30 30 37 36 20 a 0D V. Position n = -5 (a=2D 35) ~ 5 (a=35) By timing

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX77 n 7E 30 30 37 37 20 aabbcc 0D Security Security Timer Month/Day/Hour n = mm/dd/hh

mm= 00 (aa=30 30) ~ 12 (aa=31 32) dd = 00 (bb=30 30) ~ 30 (bb=33 30)

hh= 00 (cc=30 30) ~ 24 (cc=32 34) ~XX78 1 7E 30 30 37 38 2 0 31 0D Security Settings Enable ~XX78 2 7E 30 30 37 38 2 0 32 0D Disable

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX79 n 7E 30 30 37 39 20 a 0D Projector ID n = 00 (a=30 30) ~ 99 (a=39 39)

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

62

English

Appendices

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX80 1 7E 30 30 38 30 2 0 31 0D Mute On ~XX80 0 7E 30 30 38 30 20 3 0 0D Off (0/2 for backward compatible) ~XX81 n 7E 30 30 38 31 2 0 a 0D Volume n = 0 (a=30) ~ 10 (a=31 30)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX82 1 7E 30 30 38 32 2 0 31 0D Logo Optoma ~XX82 2 7E 30 30 38 32 20 3 2 0D User ~XX82 3 7E 30 30 38 32 2 0 33 0D Neutral ~XX83 1 7E 30 30 38 33 2 0 31 0D Logo Capt ure (Option)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX88 0 7E 30 30 38 38 20 3 0 0D Closed Captioning Off ~XX88 1 7E 30 30 38 38 2 0 31 0D cc1 ~XX88 2 7E 30 30 38 38 2 0 32 0D cc2

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX100 1 7E 30 30 31 30 30 20 31 0D Source Lock On ~XX100 0 7E 30 30 31 30 30 20 30 0D Off (0/2 for backward compatible) ~XX100 3 7E 30 30 31 30 30 20 33 0D Next Source ~XX101 1 7E 30 30 31 30 3 1 20 31 0D High Altitude On ~XX101 0 7E 30 30 31 30 31 20 30 0D Off (0/2 for backward compatible) ~XX102 1 7E 30 30 31 30 32 20 31 0D Information Hide On ~XX102 0 7E 30 30 31 30 32 20 30 0D Off (0/2 for backward compatible) ~XX103 1 7E 30 30 31 30 33 20 31 0D Keypad Lock On ~XX103 0 7E 30 30 31 30 33 20 30 0D Off (0/2 for backward compatible)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX104 1 7E 30 30 31 30 3 4 20 31 0D Background Color Blue ~XX104 2 7E 30 30 31 30 34 20 32 0D Black ~XX104 3 7E 30 30 31 30 34 20 33 0D Red ~XX104 4 7E 30 30 31 30 34 20 34 0D Green ~XX104 5 7E 30 30 31 30 34 20 35 0D White

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX105 1 7E 30 30 31 30 35 20 31 0D Advanced Direct Power On On ~XX105 0 7E 30 30 31 30 3 5 20 30 0D Off (0/2 for backward compatible) ~XX106 n 7E 30 30 31 30 36 20 a 0D Auto Power Off (min) n = 0 (a=30) ~ 180 (a=31 38 30) step:5 ~XX107 n 7E 30 30 31 30 37 20 a 0D Sleep Timer (min) n = 0 (a=30) ~ 995 (a=39 39 39) step:5 ~XX114 1 7E 30 30 31 31 34 20 31 0D Power Mode(Standby) Eco.(<=1W) ~XX114 0 7E 30 30 31 31 34 20 30 0D Active (0/2 for backward co mpatible)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX109 1 7E 30 30 31 30 39 20 31 0D Lamp Reminder On ~XX109 0 7E 30 30 31 30 3 9 20 30 0D Off (0/2 for backward compatible) ~XX110 1 7E 30 30 31 31 30 20 31 0D Brightness Mode Bright ~XX110 0 7E 30 30 31 31 30 20 30 0D Eco. (0/2 for backward compatible) ~XX111 1 7E 30 30 31 31 31 20 31 0D Lamp Reset Yes ~XX111 0 7E 30 30 31 31 31 20 30 0D No (0/ 2 for backward compatible)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX112 1 7E 30 30 31 31 3 2 20 31 0D Reset Yes

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX99 1 7E 30 30 39 39 20 3 1 0D RS232 Alert Res et Reset System Alert ~XX210 n 7E 30 30 32 30 30 20 n 0D Displ ay message on the OSD n: 1-30 characters

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

SEND to emulate Remote

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX140 1 7E 30 30 31 34 30 20 31 0D Power ~XX140 3 7E 30 30 31 34 3 0 20 33 0D Remote Mouse Up ~XX140 4 7E 30 30 31 34 30 20 34 0D Remote Mouse Le ft ~XX140 5 7E 30 30 31 34 3 0 20 35 0D Remote Mouse Enter ~XX140 6 7E 30 30 31 34 30 20 36 0D Remote Mouse Right ~XX140 7 7E 30 30 31 34 3 0 20 37 0D Remote Mouse Down ~XX140 8 7E 30 30 31 34 30 20 38 0D Mouse Left Click ~XX140 9 7E 30 30 31 34 30 20 39 0D Mouse Right Click ~XX140 10 7E 30 30 31 34 30 20 31 30 0D Up/Page + ~XX140 11 7E 30 30 31 34 30 20 31 31 0D Left/Source ~XX140 12 7E 30 30 31 34 30 20 31 32 0D Enter (for pro jection MENU) ~XX140 13 7E 30 30 31 34 30 20 31 33 0D Right/Re-SYNC ~XX140 14 7E 30 30 31 34 30 20 31 34 0D Down/Page ~XX140 15 7E 30 30 31 34 30 20 31 35 0D Keystone + ~XX140 16 7E 30 30 31 34 30 20 31 36 0D Keystone ~XX140 17 7E 30 30 31 34 30 20 31 37 0D Volume ~XX140 18 7E 30 30 31 34 30 20 31 38 0D Volume + ~XX140 19 7E 30 30 31 34 30 20 31 39 0D Brightness (1) ~XX140 20 7E 30 30 31 34 30 20 32 30 0D Menu (2) ~XX140 21 7E 30 30 31 34 30 20 32 31 0D 3D (3 ) ~XX140 22 7E 30 30 31 34 30 20 32 32 0D HDMI (4) ~XX140 23 7E 30 30 31 34 30 20 32 33 0D Freeze (5) ~XX140 24 7E 30 30 31 34 30 20 32 34 0D AV Mute (6) ~XX140 25 7E 30 30 31 34 30 20 32 35 0D S-Video (7) ~XX140 26 7E 30 30 31 34 30 20 32 36 0D VGA1/2 toggle (8) ~XX140 27 7E 30 30 31 34 30 20 32 37 0D Video (9)

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

63

English

Appendices

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

SEND from projector automatica lly

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

232 ASCII Code HEX Code Function Projector Return Description

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------when Standby/Warming/Cooling/Out of Range / System status INFOn n : 0/1/2/3/4/6/7/8/9 = Standby/Warming/Cooling/Out of Range/ Lamp fail/Fan Lock/Over Temperature/ Lamp fail/Fan Lock/Over Temperature/Lamp Hours Running O ut/ Lamp Hour s Running Out/C over Open Cover Open

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

READ from projector

----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

232 ASCII Code HEX Code Function Projector Return Description

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX121 1 7E 30 30 31 32 31 20 31 0D Input Source Commands OKn n : 0/1/2/3/4/5 = Non e/VGA1/VGA2/S-Video/Video/HDMI ~XX122 1 7E 30 30 31 32 3 2 20 31 0D Sofware Version OKdddd dddd: FW version ~XX123 1 7E 30 30 31 32 33 20 31 0D Display Mode OKn n : 0/1/2/3/4/5/7/8/9 = None/Presentation /Bright/Movie/sRGB/

User/Blackboard/Classroom/3D ~XX124 1 7E 30 30 31 32 34 20 31 0D Power State OKn n : 0/1 = Off/On ~XX125 1 7E 30 30 31 32 35 20 31 0D Brightness OKn ~XX126 1 7E 30 30 31 32 36 20 31 0D Contrast OKn ~XX127 1 7E 30 30 31 32 37 20 31 0D Aspect Ratio OKn n : 0/1/2/3/4/5 = 4:3/16:9 or 16:10/LBX/Native/A UTO (WXGA)

n : 0/1/2/3/4/5 = 4:3/16:9-I/16:10-II /Native/AUTO (XGA) ~XX128 1 7E 30 30 31 32 38 20 31 0D Color Temperature OKn n : 0/1/2 = Warm/Med ium/Cold ~XX129 1 7E 30 30 31 32 3 9 20 31 0D Projection Mode OKn n : 0/1/2/3 = Front-Desktop/ Rear-Desktop/ Front-Ceiling/

Rear-Ceiling ~XX150 1 7E 30 30 31 35 30 20 31 0D Information OKabbbbccdddde a : 0/1 = Off/On

bbbb: LampHour

cc: source

00/01/02/03/04/05 = None/VGA1/VGA2 /S-Video/Video/HDMI

dddd: FW version

e : Display mode 0/1/2/3/4/5 //7/8/9=None/Presentation/Bright/

Movie/sRGB/User/Blackboard/Classroom/3D ~XX151 1 7E 30 30 31 35 31 20 31 0D Model name OKn n:16/17 = EW615i/EX615i ~XX108 1 7E 30 30 31 30 38 20 31 0D Lamp Hours OKbbbb bbbb: LampHour ~XX108 2 7E 30 30 31 30 38 20 31 0D Cumulative Lamp Hours OKbbbbb bbbbb: (5 digits) Total Lamp Hours

----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

64

English

Appendices

82.3093.60

110.00 137.2076.40

55.00

323.60

233.30

59.01

89.75

Please note that

damage resulting from incorrect installation will void the warranty.

Warning:

1. If you buy a ceiling mount from another company, please

be sure to use the

correct screw size. Screw size will vary

depending on the

thickness of the mounting plate.

2. Be sure to keep at least 10 cm gap between the ceiling and the bottom of the

projector.

3. Avoid installing the projector near a heat source.

Ceiling Mount Installation

1. To prevent damage to your projector, please use the Optoma ceiling mount.

2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to the projector

meet the following specifications:

Screw type: M3*3



Maximum screw length: 10mm



 Minimum screw length: 7.5mm

Unit: mm

Lens

65

English

Appendices

Optoma Global Ofces

For service or support please contact your local ofce.

USA

3178 Laurelview Ct. 888-289-6786 Fremont, CA 94538, USA 510-897-8601 www.optomausa.com services@optoma.com

Canada

2420 Meadowpine Blvd., Suite #105 888-289-6786 Mississauga, ON, L5N 6S2, Canada 510-897-8601 www.optoma.ca services@optoma.com

Latin America

3178 Laurelview Ct. 888-289-6786 Fremont, CA 94538, USA 510-897-8601 www.optomausa.com services@optoma.com

Europe

42 Caxton Way, The Watford Business Park

Watford, Hertfordshire, WD18 8QZ, UK +44 (0) 1923 691 800

www.optoma.eu +44 (0) 1923 691 888 Service Tel : +44 (0)1923 691865 service@tsc-europe.com

Benelux BV

Randstad 22-123 +31 (0) 36 820 0253 1316 BW Almere +31 (0) 36 548 9052

The Netherlands

www.optoma.nl

France

Bâtiment E +33 1 41 46 12 20

81-83 avenue Edouard Vaillant +33 1 41 46 94 35 92100 Boulogne Billancourt, France savoptoma@optoma.fr

Spain

C/ José Hierro,36 Of. 1C +34 91 499 06 06

28522 Rivas VaciaMadrid, +34 91 670 08 32 Spain

66

English

Appendices

Deutschland

Wiesenstrasse 21 W +49 (0) 211 506 6670 D40549 Düsseldorf, +49 (0) 211 506 66799 Germany info@optoma.de

Scandinavia

Lerpeveien 25 +47 32 98 89 90 3040 Drammen +47 32 98 89 99 Norway info@optoma.no

PO.BOX 9515

3038 Drammen Norway

Korea

WOOMI TECH.CO.,LTD.

4F,Minu Bldg.33-14, Kangnam-Ku, +82+2+34430004 seoul,135-815, KOREA +82+2+34430005

Japan

東京都足立区綾瀬3-25-18 株式会社オーエスエム info@osscreen.com サポートセンター:0120-46-5040 www.os-worldwide.com

Taiwan

5F., No. 108, Minchiuan Rd. +886-2-2218-2360 Shindian City, +886-2-2218-2313 Taipei Taiwan 231, R.O.C. services@optoma.com.tw www.optoma.com.tw asia.optoma.com

Hong Kong

Unit A, 27/F Dragon Centre,

79 Wing Hong Street, +852-2396-8968 Cheung Sha Wan, +852-2370-1222

Kowloon, Hong Kong www.optoma.com.hk

China

5F, No. 1205, Kaixuan Rd., +86-21-62947376 Changning District +86-21-62947375

Shanghai, 200052, China www.optoma.com.cn

67

English

Appendices

Regulation & Safety Notices

This appendix lists the general notices of your projector.

FCC notice

This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This device generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not

occur in a particular installation. If this device does cause

harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the device and receiver.

• Connect the device into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television

technician for help.

Notice: Shielded cables

All connections to other computing devices must be made using shielded cables to maintain compliance with

FCC regulations.

Caution

Changes or modications not expressly approved by the manufacturer could void the user’s authority, which is granted by the Federal Communications Commission, to

operate this projector.

68

English

Appendices

Operation conditions

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference and

2. This device must accept any interference received,

including interference that may cause undesired

operation.

Notice: Canadian users

This Class B digital apparatus complies with Canadian

ICES-003.

Remarque à l’intention des utilisateurs canadiens

Cet appareil numerique de la classe B est conforme a la norme

NMB-003 du Canada.

Declaration of Conformity for EU countries

• EMC Directive 2004/108/EC (including amendments)

• Low Voltage Directive 2006/95/EC

• R & TTE Directive 1999/5/EC (if product has RF function)

Disposal instructions

Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle it.

Optoma Technology TW615GOV User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents

Usage Notice

Safety Information

Precautions

Eye Safety Warnings

Product Features

Introduction

Package Overview

Product Overview

Main Unit

Control Panel

Input/Output Connections

Remote Control

Installation

Connecting the Projector

Connect to Computer/Notebook

Connect to Video Sources

Powering the projector On / Off

Powering On the Projector

Powering Off the Projector

Warning Indicator

Adjusting the Projected Image

Adjusting the Projector’s Height

Adjusting the Projector’s Zoom / Focus

Adjusting Projection Image Size

User Controls

Control Panel & Remote Control

Control Panel

Remote Control

On-screen Display Menus

How to operate

Menu Tree

IMAGE

IMAGE | Advanced

DISPLAY

DISPLAY | 3D

SETUP

SETUP | Security

SETUP | Advanced

SETUP | Network

OPTIONS

Appendices

Troubleshooting

Replacing the lamp

Compatibility Modes

Computer Compatibility

Video Compatibility

RS232 Commands and Protocol Function List

RS232 Pin Assignments

RS232 Protocol Function List

Ceiling Mount Installation

Regulation & Safety Notices