Video Compatibility ............................ 79
RS232 Commands and Protocol
Function List .....................................80
RS232 Pin Assignments .................... 80
RS232 Protocol Function List ............ 81
Wall Mount Installation ......................85
Optoma Global Ofces .....................86
Regulation & Safety Notices .............88
2
English
Usage Notice
Safety Information
The lightning ash with arrow head within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufcient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH
VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE
CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Class B emissions limits
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Important Safety Instruction
1. Do not block any ventilation openings. To ensure reliable operation of
the projector and to protect from over heating, it is recommended to
install the projector in a location that does not block ventilation. As an
example, do not place the projector on a crowded coffee table, sofa,
bed, etc. Do not put the projector in an enclosure such as a book case
or a cabinet that restricts air ow.
2. Do not use the projector near water or moisture. To reduce the risk
of re and/or electric shock, do not expose the projector to rain or
moisture.
3. Do not install near heat sources such as radiators, heaters, stoves or
any other apparatus such as ampliers that emits heat.
4. Clean only with dry cloth.
5. Only use attachments/accessories specied by the manufacturer.
6. Do not use the unit if it has been physically damaged or abused.
Physical damage/abuse would be (but not limited to):
Unit has been dropped.
Power supply cord or plug has been damaged.
Liquid has been spilled on to the projector.
Projector has been exposed to rain or moisture.
Something has fallen in the projector or something is loose inside.
Do not attempt to service the unit yourself. Opening or removing covers
may expose you to dangerous voltages or other hazards. Please call
Optoma before you send the unit for repair.
7. Do not let objects or liquids enter the projector. They may touch
dangerous voltage points and short out parts that could result in re or
electric shock.
8. See projector enclosure for safety related markings.
9. The unit should only be repaired by appropriate service personnel.
3
English
Usage Notice
Precautions
Please follow all warnings, precautions and
maintenance as recommended in this user’s
guide.
▀■ Warning- Do not look into the projector’s lens when the lamp is
on. The bright light may hurt and damage your eyes.
▀■ Warning- To reduce the risk of re or electric shock, do not
expose this projector to rain or moisture.
▀■ Warning- Please do not open or disassemble the projector as
this may cause electric shock.
▀■ Warning- When replacing the lamp, please allow the unit to
cool down. Follow instructions as described on pages
76-77.
▀■ Warning- This projector will detect the life of the lamp itself.
Please be sure to change the lamp when it shows
warning messages.
▀■ Warning- Reset the “Lamp Reset” function from the on-screen
display “OPTIONS | Lamp Settings” menu after
replacing the lamp module (refer to page 53).
When the lamp
reaches the end
of its life, the pro-
jector will not turn
back on until the
lamp module has
been replaced.
To replace the
lamp, follow the
procedures listed
under “Replacing
the Lamp” section
on pages 76-77.
▀■ Warning- When switching the projector off, please ensure
the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the
projector to cool down.
▀■ Warning- Do not use lens cap when projector is in operation.
▀■ Warning- When the lamp is approaching the end of its lifetime,
the message “Lamp Warning: Lamp life exceeded.”
will show on the screen. Please contact your local
reseller or service center to change the lamp as soon
as possible.
▀■ Warning- Do not look into or point the laser pointer on your
remote control into your or someone’s eyes. Laser
pointer can cause permanent damage to eyesight.
4
English
Usage Notice
Do:
Turn off and unplug the power plug from the AC outlet before
cleaning the product.
Use a soft dry cloth with mild detergent to clean the display
housing.
Disconnect the power plug from AC outlet if the product is
not being used for a long period of time.
Do not:
Block the slots and openings on the unit provided for
ventilation.
Use abrasive cleaners, waxes or solvents to clean the unit.
Use under the following conditions:
- In extremely hot, cold or humid environments.
Ensure that the ambient room temperature is within
5 - 35°C.
Relative Humidity is 5 - 35°C, 80% (Max.),
non-condensing.
- In areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic eld.
- In direct sunlight.
5
English
Usage Notice
Eye Safety Warnings
▀■ Avoid staring/facing directly into the projector beam at all
times. Keep your back to the beam as much as possible.
▀■ When projector is used in a classroom, adequately supervise
students when they are asked to point out something on the
screen.
▀■ In order to minimize the lamp power, use room blinds to
reduce ambient light levels.
Product Features
Monitor loop
through only support in VGA1-In/
YPbPr.
▀■ XGA (1024x768) Native resolution /
WXGA (1280x800) Native resolution
▀■ HD compatible – 1080p supported
▀■ VGA monitor loop through
(works on standby mode > 1W)
▀■ BrilliantColorTM Technology
▀■ Security Bar and Kensington Lock
▀■ RS232 control
▀■ Rapid shutdown
▀■ Built-in speakers
▀■ Network support
▀■ USB display (Mac OS is not supported)
▀■ Network display (Windows 7 64bit is not supported)
▀■ USB Reader
6
English
Introduction
Package Overview
Unpack and inspect the box contents to ensure
all parts listed below are in the box. If something
is missing, please contact your nearest customer
service center.
Due to different
applications in
each country,
some regions
may have
different
accessories.
Projector with lens cap
2 × AAA Batteries
Documentation :
User’s Manual
Warranty Card
Quick Start Card
WEEE Card
(for EMEA only)
STOP Card
(for US Only)
Power Cord
IR Remote Control
VGA Cable
USB Cable 5m
7
English
Introduction
Product Overview
Main Unit
6
4
56
7
8
4
9
4
1
2
3
4
4
10
11
1. Control Panel
2. Focus Ring
3. Speaker
4. Tilt-Adjustment Feet
5. Lens
6. IR Receiver
Air Flow
7. Input / Output
Connections
8. Power Socket
9. Security Bar
10. Ventilation (inlet)
11. Ventilation (outlet)
8
English
Introduction
LAMP
TEMP
POWER/STANDBY
MENU
S
O
U
R
C
E
Control Panel
231
10
9
7
1. Source
2. Enter / Help
3. Re-Sync
4. IR Receiver
5. Temp LED
6. Presenter
7. Four Directional Select Keys
8. Power/Standby button and LED
9. Keystone Correction
10. Menu
11. Lamp LED
4
511
68
9
English
Introduction
AUDIO OUT
AUDIO1-IN
(VGA1/VGA2)
RS-232
MIC
LR
AUDIO 2-IN (S-VIDEO/VIDEO)
VIDEOS-VIDEO
HDMI
VGA-OUT
VGA1-IN / YPbPr
VGA2-IN / YPbPr
RJ-45
PB/MOUSE
SERVICE
12V OUT
USB /
DISPLAY
12V OUT
Input/Output Connections
1
Monitor loop
through only support in VGA1-In/
YPbPr.
15
6542
14
131119
378910
1612
1718
1. RJ-45 Networking Connector
2. 5pin Mini-USB for interactive function and rmware upgrade
12.............................................................................................. *12V DC Plug
14
English
Installation
LAMP
TEMP
POWER/STANDBY
MENU
S
O
U
R
C
E
When Power mode
(Standby) is set
to Eco (<1W), the
VGA output, Audio
pass-through
and RJ45 will be
deactivated when
the projector is in
standby.
Powering the projector On / Off
Powering On the Projector
1. Remove the lens cap.
2. Securely connect the power cord and signal cable. When
connected, the POWER/STANDBY LED will turn Amber.
3. Turn on the lamp by pressing “ ” button either on the top of
the projector or on the remote. The POWER/STANDBY LED
will now turn Green.
The startup screen will display in approximately 10 seconds.
The rst time you use the projector, you will be asked to
select the preferred language and power saving mode.
4. Turn on and connect the source that you want to display
on the screen (computer, notebook, video player, etc). The
projector will detect the source automatically. If not, push
menu button and go to “OPTIONS”.
Make sure that the “Source Lock” has been set to “Off”.
If you connect multiple sources at the same time, press the
“SOURCE” button on the control panel or direct source keys
on the remote control to switch between inputs.
Turn on the
projector rst and
then select the
signal sources.
2
POWER/STANDBY
1
Lens Cap
15
English
Installation
Powering Off the Projector
1. Press the “ ” button on the remote control or
on the control panel to turn off the projector.
The following message will be displayed on the screen.
Press the “ ” button again to conrm otherwise the
message will disappear after 15 seconds. When you
press the “ ” button for the second time, the projector will
display countdown timer and will shut down.
2. The cooling fans continue to operate for about 10 seconds
for cooling cycle and the POWER/STANDBY LED will
Flash Green. When the POWER/STANDBY LED lights
solid Amber, the projector has entered standby mode.
If you wish to turn the projector back on, you must wait
until the projector has completed the cooling cycle and
has entered standby mode. Once in standby mode, simply
press “ ” button to restart the projector.
3. Disconnect the power cord from the electrical outlet and
the projector.
4. Do not turn on the projector immediately following a power
off procedure.
Contact the
nearest service
center if the
projector displays
these symptoms.
See pages
86-87 for more
information.
Warning Indicator
When the warning indicators (see below) come on,
the projector will automatically shutdown:
“LAMP” LED indicator is lit red and if “POWER/STANDBY”
indicator ashes amber.
“TEMP” LED indicator is lit red and if “POWER/STANDBY”
indicator ashes amber. This indicates the projector has
overheated. Under normal conditions, the projector can be
switched back on.
“TEMP” LED indicator ashes red and if “POWER/STAND-
BY” indicator ashes amber.
Unplug the power cord from the projector, wait for 30 seconds
and try again. If the warning indicator light up again, please
contact your nearest service center for assistance.
16
English
Installation
Adjusting the Projected Image
Adjusting the Projector’s Height
The projector is equipped with elevator feet for adjusting
the image height.
1. Locate the adjustable foot you wish to modify on the
underside of the projector.
2. Rotate the adjustable ring clockwise to raise the projector
or counter clockwise to lower it. Repeat with the remaining
feet as needed.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
17
English
Installation
Width
Height
Diagonal
Top View
Side View
Projection Distance (D)
Projection Distance (D)
Screen
Screen
Screen (W)
Screen (H)
Offset (Hd)
Adjusting the Projector’s Focus
To focus the image, rotate the focus ring until the image is clear.
XGA series: The projector will focus at distances from 1.64
to 12.46 feet (0.5 to 3.8 meters).
WXGA series: The projector will focus at distances from 1.64
to 11.15 feet (0.5 to 3.4 meters).
Focus Ring
Adjusting Projection Image Size
XGA series: Projection Image Size from 41.0” to 312.0” (1.0
to 7.9 meters).
WXGA series: Projection Image Size from 44.6” to 303.0”
Refer to the “Power On/Off the Projector” section on
pages 14-15.
Automatically synchronize the projector to the input
source.
Conrm your item selection.
Enter / Help
/
Help Menu (only available when OSD menu is not
shown).
SOURCE
Menu
Four Directional
Select Keys
Keystone
Press “SOURCE” to select an input signal.
Press “Menu” to launch the on-screen display
(OSD) menu. To exit OSD, Press “Menu” again.
Use to select items or make adjustments to your selection.
Use to adjust image distortion caused
by tilting the projector. (±40 degrees)
PresenterDirect key for LAN/Wireless.
Lamp LEDIndicate the projector’s lamp status.
Temp LEDIndicate the projector’s temperature status.
POWER/
STANDBY
Indicate the projector’s status.
LED
20
English
User Controls
Remote Control
Using the Remote Control
Power
L Button
R Button
Page +
Page -
Enter / Help
Source
Re-SYNC
Four Directional
Select Keys
Keystone +/-
Volume +/-
Refer to the “Power On/Off the Projector”
section on pages 14-15.
Mouse left click.
Mouse right click.
Use this button to page up.
Use this button to page down.
Conrm your item selection.
Help Menu (only available when OSD
menu is not shown).
Press “Source” to select an input signal.
Automatically synchronizes the projector to
the input source.
Use to select items or make
adjustments to your selection.
Adjust image distortion caused by tilting the
projector.
Adjust to increase / decrease the volume.
Brightness
3D
Menu
HDMI
Freeze
Adjust the brightness of the image.
Press the “3D” to turn the 3D OSD menu
on/off.
Press “Menu” to launch the on-screen
display (OSD) menu. To exit OSD, press
“Menu” again.
Press “HDMI” to choose HDMI source.
Press “Freeze” to pause the screen image.
Press this button again to unlock.
21
English
User Controls
Using the Remote Control
AV mute
S-Video Press “S-Video” to choose S-Video source.
VGA
Video
Momentarily turns off/on the audio and
video.
Press “VGA” to choose VGA sources.
Press “Video” to choose Composite video
source.
Interactive Pen
Using the Interactive Pen
ON/OFF
LED
LED
Nib
Mouse Left
Click
Power On/Off the Interactive Pen.
Indicate the interactive pen’s status.
Indicate the interactive pen’s battery consumption.
Press the nib to draw or write.
Mouse left click.
Mouse Right
Click
Menu
Mouse right click.
Press “Menu” to launch the on-screen
display (OSD) menu. To exit OSD, press
“Menu” again.
22
English
User Controls
Using the HELP button
The HELP function ensures easy setup and operation.
Press the “?” button on the remote control or press the
“HELP” button on the control panel to open the Help Menu.
23
English
User Controls
Please refer to the
“Troubleshooting”
section on pages
70-75 for more
details.
Help menu button functions only when no input source
is detected.
24
English
User Controls
If input source is detected and help button is pressed, the
following pages will appear to help diagnose any problems.
25
English
User Controls
26
English
User Controls
On-screen Display Menus
The Projector has multilingual On-screen Display menus that
allow you to make image adjustments and change a variety of
settings.
How to operate
1. To open the OSD menu, press “Menu” on the Remote Control or
Projector Keypad.
2 When OSD is displayed, use
main menu. While making a selection on a particular page, press
or “Enter” key to enter sub menu.
3.Use
using key.
4. Select the next item to be adjusted in the sub menu and adjust as
described above.
5. Press “Enter” to conrm, and the screen will return to the main
menu.
6. To exit, press “MENU” again. The OSD menu will close and the
projector will automatically save the new settings.
keys to select the desired item and adjust the settings
keys to select any item in the
Main Menu
Sub Menu
Settings
27
English
User Controls
Main MenuSub MenuSettings
Image
Display Mode
Brightness0~100
Contrast0~100
Sharpness0~31
Color0~100
Tint0~100
AdvancedGammaFilm / Video / Graphics / Standard
0~10
Color Temp.Warm / Medium / Cold
Color Settings
Color SpaceAUTO / RGB / YUV
Input Source
Exit
Display
Format4:3 / 16:9-I / 16:9-II / Native / AUTO
4:3 / 16:9 or 16:10 / LBX / Native / AUTO
Edge Mask0~10
Zoom -5~25 (80%~200%)
H Image Shift-50~50
V Image Shift-50~50
V Keystone-40~40
3D3D Mode
3D Sync. InvertOn / Off
Exit
Setup
Language
Screen Type16:10 / 16:9
Projection
Menu Location
SignalAutomaticOn / Off
Phase (VGA)0~31
Frequency (VGA)-5~5
H. Position (VGA)-5~5
V. Position (VGA)-5~5
Exit
ʳ
SecuritySecurityOn / Off
Security TimerMonth / Day / Hour
Change Password
ʳ
Exit
#7
Presentation / Bright / Movie / sRGB /
Blackboard / Classroom / User / 3D
#1
#1
BrilliantColor™
Red Gain / Green Gain / Blue Gain / Red
Bias / Green Bias / Blue Bias / Cyan /
Magenta / Yellow / Reset / Exit
VGA1 / VGA2 / Video / S-Video / HDMI /
Flash Drive / Presenter / USB Display
#2
#3
Off / DLP-Link / IR
#4
English / Deutsch / Français / Italiano /
Español / Português / Svenska /
Nederlands / Norsk/Dansk / Polski /
Suomi / Ɋɭɫɫɤɢɣ / İȜȜȘȞȚțȐ / Magyar /
ýeština / γέΎϓ / ϲΑήϋ /
᧯խ֮ʳ/ 亞խ֮ʳ/
ֲ
ء!0ᾂ᱑ʳ/ ࡷࡎ࡙/ Türkçe / ViӋt /
Bahasa Indonesia / Română
#3
#5
Menu Tree
28
English
User Controls
Main MenuSub MenuSettings
Setup
Projector ID0~99
MuteOn / Off
Volume0~20
Audio InputDefault / Audio1 / Audio2 / MIC
AdvancedLogo
Logo Capture
Closed CaptioningOff / CC1 / CC2
Exit
NetworkNetwork State
DHCP
IP Address
Gateway
DNS
ApplyYes / No
Exit
Options
Source LockOn / Off
High AltitudeOn / Off
Information HideOn / Off
Keypad LockOn / Off
Background ColorBlack / Red / Blue / Green / White
IR ReceiverTop ReceiverOn / Off
Front ReceiverOn / Off
AdvancedDirect Power OnOn / Off
Auto Power Off (min.)0~180
Sleep Timer (min.)0~995
Power Mode (Standby)Eco. / Active
Exit
Lamp SettingsLamp Hour
Lamp ReminderOn / Off
Brightness ModeEco. / Bright / Image AI
Lamp ResetYes / No
Exit
InteractiveOn / Off
Dual PenOn / Off
Pointer MotionNormal / Draw / Stable
Click SpeedFast / Medium / Low
Set function
ChannelAutomatic / Channel
Information
Reset
#6
Optoma / Neutral / User
Subnet mask
PointBlank
Pointer Motion / PowerPoint Annotation /
Switch Window (Alt+Tab) / Esc / Show
Desktop (Cmd+D) / Open Windows
Explorer (Cmd+E) / Middle Mouse / Double
Click / Disable
Pen1 Battery Capacity / Pen1 RF
Strength / Pen2 Battery Capacity / Pen2
RF Strength / Channel / Receiver / Pen1 /
Pen2
29
English
User Controls
Please note that the on-screen display (OSD) menus vary according to the
signal type selected and the projector model you are using.
(#1) “Color” and “Tint” are only supported in Video mode.
(#2) For XGA model only.
(#3) For WXGA model only. 16:9 or 16:10 depend on “Screen Type” setting.
(#4) “3D Sync Invert” is only available when 3D is enabled.
(#5) “Signal” is only supported in Analog VGA (RGB) signal.
(#6) MIC volume can also be controlled by “Setup Volume” in OSD.
(#7) When PointBlank is enabled, “Display Mode” will support “Presenta-
tion”, “Bright”, “User” and “3D” modes only.
30
English
User Controls
IMAGE
Display Mode
There are many factory presets optimized for various types of
images.
Presentation: Good color and brightness from PC input.
Bright: Maximum brightness from PC input.
Movie: For home theater.
sRGB: Standardised accurate color.
Blackboard: This mode should be selected to achieve optimum
color settings when projecting onto a blackboard (green).
Classroom: This mode is recommended for projecting in a
classroom.
User: User’s settings.
3D: Recommand setting for 3D mode enabled. Any further ad-
justments by the user in 3D will be saved in this mode for further
use.
Brightness
Adjust the brightness of the image.
Press the to darken image.
Press the to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture.
Press the to decrease the contrast.
Press the to increase the contrast.
31
English
User Controls
“Color” and “Tint”
functions are only
supported under
Video mode.
Sharpness
Adjust the sharpness of the image.
Press the to decrease the sharpness.
Press the to increase the sharpness.
Color
Adjust a video image from black and white to fully saturated color.
Press the to decrease the amount of saturation in the image.
Press the to increase the amount of saturation in the image.
Tint
Adjust the color balance of red and green.
Press the to increase the amount of green in the image.
Press the to increase the amount of red in the image.
32
English
User Controls
IMAGE | Advanced
Gamma
This allows you to choose a degamma table that has been
ne-tuned to bring out the best image quality for the input.
Film: for home theater.
Video: for video or TV source.
Graphics: for image source.
Standard: for PC or computer source.
BrilliantColor™
This adjustable item utilizes a new color-processing algorithm and
system level enhancements to enable higher brightness while
providing true, more vibrant colors in picture. The range is from
“0” to “10”. If you prefer a stronger enhanced image, adjust toward
the maximum setting. For a smoother, more natural image, adjust
toward the minimum setting.
Color Temp
If set to cold temperature, the image looks more blue. (cold image)
If set to warm temperature, the image looks more red.
(warm image)
Color Settings
Press into the next menu as below and then use or to
select item.
Red Gain/Green Gain/Blue Gain/Red Bias/Green Bias/Blue
Bias/Cyan/Magenta/Yellow: Use
Blue, Cyan, Magenta and Yellow Colors.
Reset: Choose “Yes” to return the factory default settings for
color adjustments.
or to select Red, Green,
33
English
User Controls
Color Space
Select an appropriate color matrix type from AUTO, RGB or YUV.
Input Source
Use this option to enable / disable input sources. Press to enter
the sub menu and select which sources you require. Press “Enter”
to finalize the selection. The projector will not search for inputs that
are not selected.
34
English
User Controls
DISPLAY
Format
Use this function to choose your desired aspect ratio.
XGA
4:3: This format is for 4×3 input sources.
16:9-I: This format is for 16×9 input sources, like HDTV and
DVD enhanced for Wide screen TV. (576i/p)
16:9-II: This format is for 16×9 input sources, like HDTV and
DVD enhanced for Wide screen TV. (480i/p)
Native: This format displays the original image without any
scaling.
AUTO: Automatically selects the appropriate display format.
When input is 4:3, the image is displayed as 4:3. When input is
16:9 above, the image is displayed as 16:9- I
Aspect ratio
(source detected)
4:31024 x 768 center
16:9-I1024 x 576 center
16:9-II854 x 480 center
No resize image, 1:1 mapping and
Native
centered. This format shows the
original image without scaling.
Resize image
XGA model
35
English
User Controls
16:9 or 16:10
depend on “Screen
Type” setting.
WXGA
4:3: This format is for 4×3 input sources.
16:9: This format is for 16×9 input sources, like HDTV and DVD
enhanced for Wide screen TV.
16:10: This format is for 16×10 input sources, like widescreen
laptops.
LBX: This format is for non-16x9, letterbox source and for users
who use external 16x9 lens to display 2.35:1 aspect ratio using
full resolution.
Native: This format displays the original image without any
scaling.
AUTO: Automatically selects the appropriate display format.
16:10 Screen480i/p576i/p1080i/p720pPC
4:31066 x 800 center
16:101280 x 800 center
LBX
Native
1280 x 960 center, then get the central 1280 x 800 image
1:1 mapping
centered.
to display
1:1 map-
ping (960 x
540) display
1280 x 800
1280 x 720
center
1:1
mapping
centered.
16:9 Screen480i/p576i/p1080i/p720pPC
4:3960 x 720 center
16:91280 x 720 center
LBX
Native
1280 x 960 center, then get the central 1280 x 720 image
1:1 mapping
centered.
to display
1:1 map-
ping (960 x
540) display
1280 x 720
1280 x 720
center
1:1
mapping
centered.
36
English
User Controls
Edge Mask
Edge mask function removes the noise in a video image. Edge
Each I/O has
different setting of
“Edge mask”.
“Edge mask” and
“Zoom” can’t work at
same time.
mask the image to remove video encoding noise on the edge of
video source.
Zoom
Press the to reduce the size of an image.
Press the to magnify an image on the projection screen.
H Image Shift
Shift the projected image position horizontally.
V Image Shift
Shift the projected image position vertically.
V Keystone
Press the or to adjust image distortion vertically. If the image
looks trapezoidal, this option can help make the image rectangular.
37
English
User Controls
DISPLAY | 3D
“IR” options may
vary according to
model.
“3D Sync Invert” is
only available when
3D is enabled and
this mode 3D is for
DLP link glass only.
Compatible 3D
source, 3D content
and active shutter
glasses are required
for 3D viewing.
3D Mode
Off: Select “Off” to turn 3D settings off for 3D images.
DLP Link: Select “DLP Link” to use optimized settings for DLP
Link 3D images.
IR: Select “IR” to use optimized settings for IR-based 3D
images.
3D Sync. Invert
Press the “On” to invert left and right frame contents.
Press the “Off” for default frame contents.
38
English
User Controls
SETUP
Language
Choose the multilingual OSD menu. Press or into the sub
menu and then use the or key to select your preferred
language. Press “Enter” to nalize the selection.
“Screen Type” is for
WXGA only.
Rear-Desktop and
Rear-Ceiling are
to be used with a
translucent screen.
Screen Type
Choose the screen type from16:10 or 16:9.
Projection
Front-Desktop
This is the default selection. The image is projected straight on
the screen.
Front-Ceiling
When selected, the image will turn upside down.
Rear-Desktop
When selected, the image will appear reversed.
39
English
User Controls
Rear-Ceiling
When selected, the image will appear reversed in upside down
position.
Menu Location
Choose the menu location on the display screen.
Projector ID
ID denition can be set up by menu (range 0-99), and allow user
control an individual projector by RS232. Refer to pages 81-84 for
the complete list of RS232 commands.
Mute
Choose the “On” to turn mute on.
Choose the “Off” to turn mute off.
40
English
User Controls
SETUP
Volume
Press the to decrease the volume.
Volume adjustment
can also control MIC
volume.
Press the to increase the volume.
Audio Input
The default audio settings are on the back panel of the
projector. Use this option to reassign any of the Audio Inputs
(1 or 2) to the current image source. Each Audio input can be
assigned to more than one video source.
Audio 1: VGA 1 and VGA 2.
Audio 2: S-Video/Video.
MIC: (No default video source)
41
English
User Controls
SETUP | Signal
“Signal” is only
supported in Analog
VGA (RGB) signal.
(RGB)
Automatic
Automatically selects the signal. If you use this function, the
Phase, frequency items are grayed out, and if Signal is not automatic, the phase, frequency items will appear for user to manually
tune and saved in settings after that for next time projector turns
off and on again.
Phase
Synchronize the signal timing of the display with the graphic card.
If the image appears to be unstable or ickers, use this function to
correct it.
Frequency
Change the display data frequency to match the frequency of
your computer’s graphic card. Use this function only if the image
appears to icker vertically.
H. Position
Press the to move the image left.
Press the to move the image right.
V. Position
Press the to move the image down.
Press the to move the image up.
42
English
User Controls
SETUP | Security
Security
On: Choose “On” to use security verication when the turning
Off: Choose “Off” to be able to switch on the projector without
Security Timer
Use this function to set the how long (Month/Day/Hour) the
Password default
value is “1234” (rst
time).
projector can be used. Once this time has elapsed you will be
requested to enter your password again.
Change Password
First time:
1. Press “” to set the password.
2. The password has to be 4 digits.
3. Use number button on the remote to enter your new
Change Password:
1. Press “” to input old password.
2. Use number button to enter current password and then
3. Enter new password (4 digits in length) using the number
4. Enter new password again and press “” to conrm.
on the projector.
password verication.
password and then press “” key to conrm your
password.
press “” to conrm.
buttons on the remote, then press “” to conrm.
43
English
User Controls
If the incorrect password is entered 3 times, the projector will
automatically shut down.
If you have forgotten your password, please contact your local
ofce for support.
44
English
User Controls
SETUP | Advanced
Logo
Use this function to set the desired startup screen. If changes are
made they will take effect the next time the projector is powered
on.
Optoma: The default startup screen.
Neutral: Logo is not displayed on startup screen.
User: Use stored picture from “Logo Capture” function.
For successful logo
capture, please
ensure that the on-
screen image does
not exceed the pro-
jector’s native resolution. (XGA:1024x768
or WXGA:1280x800).
Logo Capture
Press to capture an image of the picture currently displayed
on screen.
Closed Captioning
Use this function to set the desired startup screen. If changes are
made they will take effect the next time the projector is powered
on.
Off: select “off” to turn off the closed captioning feature.
CC1:CC1 language: American English.
CC2:CC2 language (depending on the TV channel of the
Use this function to select your desired startup screen. If you
change the setting from one to another, when you exit the OSD
menu, the new setting will take effect on next open.
On: Assign an IP address to the projector from an external
DHCP server automatically.
Off: Assign an IP address manually.
IP Address
Select an IP address.
Subnet Mask
Select subnet mask number.
Gateway
Select the default gateway of the network connected to the
projector.
DNS
Select DNS number.
Apply
Press “” and then choose “Yes” to apply the selection.
46
English
User Controls
How to use web browser to control your projector
1. Turn on DHCP to allow the DHCP
server to automatically assign an IP, or
manually enter the required network
information.
2. Then choose apply and press “
” button to complete the conguration
process.
3. Open your web browser and type in from
the OSD LAN screen then the web page
will display as below:
4. Based on net wor k web-pa ge f or the
input-string in [tools] tab, the limitation for
Input-Length is in the below list (“space”
and the other punctuation key included):
CategoryItem
IP Address15
Crestron Control
Projector
Network
Conguration
User Password
Admin Password
IP ID2
Port5
Projector Name10
Location9
Assigned To9
DHCP (Enabled)(N/A)
IP Address15
Subnet Mask15
Default Gateway15
DNS Server15
Enabled(N/A)
New Password15
Conrm15
Enabled(N/A)
New Password15
Conrm15
Input-Length
(characters)
When you used the projector IP ad-
dress, you will can not link to your
service server.
47
English
User Controls
When making a direct connection from your computer to the projector
Step 1: Find an IP Address (192.168.0.100) from LAN function of projector.
Step 2: Select apply and press “Enter” button to submit function or press “menu” key to
exit.
Step 3: To open Network Connections,
click Start, click Control Panel,
click Network and Internet
Connections, and then click
Network Connections. Click the
connection you want to congure,
and then, under Network Tasks
, click Change settings of
this connection.
Step 4: On the General tab, under
This connection uses the
following items, click Internet
Protocol (TCP/IP), and then click
“Properties.”
Step 5: Click Use the following IP
address, and type in as below:
1) IP address: 192.168.0.100
2) Subnet mask: 255.255.255.0
3) Default gateway:192.168.0.254
Step 6: To open Internet Options, click
IE web browser, click Internet
Options, click the Connections tab and click “LAN Settings...”
Step 7: The Local Area Network (LAN)
Setting dialog box appears, In the
Proxy Server area, cancel the
Use a proxy server for your LAN
check box., then click “OK” button
twice.
Step 8: Open your IE and type in the IP
address of 192.168.0.100 in the
URL then press “Enter” key.
48
English
User Controls
Crestron RoomView Control Tool
Crestron RoomView™ provides a central monitoring station for 250+
control systems on a single Ethernet network (more are possible,
the number depends on the combination of IP ID and IP address).
Crestron RoomView monitors each projector, including projector’s
online status, system power, lamp life, network setting and hardware
faults, plus any custom attribute as dened by the Administrator.
The Administrator can add, delete, or edit room information, contact
information and events, which are logged automatically by the
software for all users. (Operation UI as following image)
1. Main Screen
2. Edit Room
Crestron Room-
View function support is dependent
on models.
49
English
User Controls
3. Edit Attribute
4. Edit Event
For more information, please visit
http://www.crestron.com & www.crestron.com/getroomview.
50
English
User Controls
OPTIONS
Source Lock
On: The projector will only search current input connection.
Off: The projector will search for other signals if the current
High Altitude
When “On” is selected, the fans will spin faster. This feature is
useful in high altitude areas where the air is thin.
Information Hide
input signal is lost.
On: Choose “On” to hide the info message.
Off: Choose “Off” to show the “searching” message.
To turn off the key-
pad lock, press and
hold “Enter” key on
top of the projector
for 5 seconds.
Keypad Lock
When the keypad lock function is “On”, the control panel will be
locked however, the projector can be operated by the remote
control. By selecting “Off”, you will be able to reuse the control
panel.
Background Color
Use this feature to display a “Black”, “Red”, “Blue”, “Green” or
“White”, screen when no signal is available.
IR Receiver
Front Receiver: Choose “On” to start the receiver. Choose “Off”
Top Receiver: Choose “On” to start the receiver. Choose “Off”
to close the receiver.
to close the receiver.
51
English
User Controls
Reset
Choose “Yes” to return the display parameters on all menus to the
factory default settings.
52
English
User Controls
OPTIONS |
Advanced
Direct Power On
Choose “On” to activate Direct Power mode. The projector will
automatically power on when AC power is supplied, without
pressing the “ ” key on the projector control panel or on the
remote control.
Auto Power Off (min)
Sets the countdown timer interval. The countdown timer will start,
when there is no signal being sent to the projector. The projector
will automatically power off when the countdown has nished (in
minutes).
When Power mode
(Standby) is set
to Eco (<1W), the
VGA output, Audio
pass-through
and RJ45 will be
deactivated when
the projector is in
standby.
Sleep Timer (min)
Sets the countdown timer interval. The countdown timer will start,
with or without a signal being sent to the projector. The projector
will automatically power off when the countdown has nished (in
minutes).
Power Mode (Standby)
Eco.: Choose “Eco.” to save power dissipation further < 1W.
Active: Choose “Active” to return to normal standby and the
VGA out port will be enabled.
53
English
User Controls
Lamp Settings
When ambient tem-
perature is over 35°C
in operating, the
projector will switch
to Eco automatically.
OPTIONS |
Lamp Hours
Display the projection time.
Lamp Reminder
Choose this function to show or to hide the warning message
when the changing lamp message is displayed.
The message will appear 30 hours before suggested replacement
of lamp.
Brightness Mode
Eco.: Choose “Eco.” to dim the projector lamp which will lower
power consumption and extend the lamp life.
BRIGHT: Choose “BRIGHT” to increase the brightness.
Image AI: Choose “Image AI” to improve the contrast of the
picture by optimizing the brightness of the lamp
according to the picture content.
Lamp Reset
Reset the lamp hour counter after replacing the lamp.
54
English
User Controls
OPTIONS |
PointBlank
Interactive
Choose “On” to enable Interactive and activate the Interactive
menu.
Dual Pen
Interactivity is sup-
ported only in the following input modes:
VGA and HDMI from
a PC, and Wire-
less Display, USB
Display, and LAN
Display
Interactive Pen is
supported in 3D
source of 120Hz
DLP-Link.
The response time
lag of Dual Pen
operation is 180ms.
Choose “On” to enable dual pen simultaneously.
Pointer Motion
Choose this function to select the Pointer Motion mode: “Normal”,
“Draw”, and “Stable”.
Normal: In this mode, press Mouse Left Click button of
the interactive pen can hold the position of the pointer for a
moment. This mode is best to use the Interactive Pen like a
mouse, i.e., for left click and double click functions.
Draw: In this mode, the pointer can move freely for drawing.
This mode is best for drawing or writing on the screen
Stable: In this mode, press and hold the Mouse Left Click
button of the interactive pen to limit the pointer to vertical or
orizontal moves. If the Mouse Left Click button is released,
the pointer can resume to move freely. This mode is best for
drawing vertical or horizontal lines on the screen.
Click Speed
Choose this function to select the mouse pause time. This function
is only available in Normal mode. The available options are: “Fast”,
“Medium” and “Low”.
Set Function
55
English
User Controls
Choose this function to select the function of the Menu button
on the interactive pen.
Pointer Motion: Function as toggling among “Normal”, “Draw”,
and “Stable” mode
PowerPoint Annotation: Function as annotating in the Power-
Point slide show.
Switch Windows (Alt+Tab): Function as toggling among
windows,acting as the keyboard shortcut Alt+Tab.
Esc: Function as the keyboard Esc button.
Show Desktop (Cmd+D): Function as showing desktop, mini-
mizing all windows.
Open Windows Explorer (Cmd+E): Choose the function as
opening the Windows Explorer.
Middle Mouse: Choose the function as the scroll wheel of the
mouse.
Double Click: Choose the function as double-clicking.
Disable: Disable the Function button.
Channel
Auto: Channel is selected automatically.
Manual: Channel is selected manually. A total of 15 channels
are available.
Information
View the information about the interactive pen.
56
English
User Controls
Ruby Introduction
Ruby is a embedded project which can bring the high performance in network projection. Base on network protocol, user
can congure the projector remotely. It supports to connect the
PC with Projector by USB, Ethernet, and Wireless. This project
makes full use of the network capability. It allows the administrator to control all the projectors in one building by one PC.
When some emergencies happen, the projector can send out
alert information to administrator by email and web page. It
can read more than one USB device directly and show all the
images in it
This project consists of three software applications which
make full use of the network and USB capability
• Web Control
• Card Reader
• Optoma Presenter
How to use Web Control
The Web Control application allows user to congure the projec-
tor remotely base on various network protocol. It is convenient for
administrator to control the whole projectors in one building by
one PC.
1. Start the web browser, and enter the IP address of the projector in
URL: http://IP-address, the log-in web page is displayed.
57
English
User Controls
2 There are 3 options in this page.
• Click “Download”, it displays the interface to download the software of “Optoma Presenter”.
• Click “Crestron”, to enter the control page of Flash UI.
• Click “Admin”, the log-in page shows up.
3.Enter the password and click [Login] button, and then main page
is displayed. The default password is “admin” when target system
is brand new. The maximum password is 8 characters with any
characters except “space”.
4. Click “Logout”, it returns back to log-in page.
System Status
This page indicates the information of Model Name, Versions, LAN
Status and Wireless Status.
General Setup
Password of entering control web page can be changed here. Old
password is requested when changing a new password.
Projector Control
All items in this page is the detail options about how to control
the projector more smoothly. Example: Power On/OFF, Source
change, Brightness, ….This page will refresh the status currently
of all the items in few seconds.
58
English
User Controls
Alert Setup
This page is to set up the alert notication for kinds of error types
by sending mail. Alert type is multi-options.
SMTP Mail Setup
This page is to set up the details of mail sending, ex. mail server
IP address, user name, password and mail address of receivers.
(Note: Multi-receivers are separated by semicolon.)
Network Setup
This page is to set up network parameters of IP, DHCP Server, and
wireless.
59
English
User Controls
• IP Setup: Click “Obtain an IP address automatically” as auto
mode; click “Use the following IP Address” as static mode, IP Ad-
dress/Subnet Mask/Default Gateway/ DNS Server are required to
be lled and then click “Apply” button.
• DHCP Server Setup: Enable/Disable, Start IP, End IP, Subnet
Mask, Default Gateway, DNS server.
• Wireless Setup: Connect with wireless dongle, and then setup
WLAN mode, SSID, KEY, Channel etc.
Presenter Setup
Admin password/User password is used to change the password
for admin/user in target side.
Click “Connection Control” to enter “Connection Status”
• Conference Control: Click “On” or “Off” to enable/disable conference control mode.
60
English
User Controls
Click the following icons under “Play Control”
• : Click to disconnect host PC.
• : Click to switch session to background.
• : Click to change display region.
Crestron RoomView
This is the control page of Flash UI.
Click “Power” to control power on/off of projector.
Click “Vol-, Mute, Vol+” to control volume.
In the SourceList, it includes all sources that the projector can
process.
Click “Menu” to open menu; click “Source” to choose next source;
click “Auto” to detect the source automatically; click “Blank” for AV
mute function.
“Contrast, Brightness, Color, Sharpness, Zoom, Freeze” can be
adjusted in the control panel below.
61
English
User Controls
Click “Tools”, the following items are included:
• Crestron Control: the basic network information of the control
system device.
• Projector: the ID of each projector in a building for Administrator
to control.
• User Password: change user’s password.
• Default Language: set the default language.
• DHCP: enable/disable DHCP and the details of network card.
After change each items, click “Send” button to make it effect.
Click “Info” to show information and status of this projector.
62
English
User Controls
Click “Help” to inform administrator to do related protection or
operation.
Reset to Default
Click “Apply” to reset system to the default settings.
Click “Flash Upgrade” to upgrade the Firmware from USB disk,
which has been inserted in projector.
Reboot System
Click “Reboot” to reboot system.
63
English
User Controls
How to use the Card Reader
The Card Reader application can display packaged images in a
USB ash device.
1. Plugging the USB device into USB port of projector, source of Flash
Drive is detected, and then USB Flash Devices Detection Screen is
displayed. It supports 3 USB devices at the same time.
2. Press “Enter” to enter Thumbnail mode, different photos in different
folders can be chosen; press “Menu” to open menu. The following
buttons are supported in the user interface:
• Previous: Move the selected item left. (Go to previous page when
this is the most left item)
• Next: Move the selected item right. (Go to next page when this is
the most right item.)
• Display: Display the selected image or folder.
• Thumbnail: Enter the Thumbnail Display Mode.
• Slide Show: Enter the Slide Show Mode.
• Name Order: Sort les/folders in name order.
• Extend Order: Sort les/folders in extended order.
• SizeOrder: Sort les/folders in size order.
• TimeOrder: Sort les/folders in time order.
• Projector Menu: Enter OSD menu.
64
English
User Controls
• File Name On/OFF: Enable/Disable le name display in Thumbnail Display Mode.
Press Up/Down/Left/Right key to choose different functions and
press Enter key to make it effect.
3. In the menu of Thumbnail mode, choose Display function, or
choose le and press “Enter” to enter Display mode. The following
buttons are supported in the user interface:
• Display: Enter the Image Display Mode.
• Thumbnail: Enter the Thumbnail Display Mode.
• Slide Show: Enter the Slide Show Mode.
• Actual Size: Display in actual size of the image.
• Best Fit: Display the image in best t to the screen.
• EXIF Disp OFF/On: Enable/Disable EXIF information display.
• +90/-90 deg: Rotate 90/-90 degree.
Press Up/Down/Left/Right key to choose different functions and
press Enter key to make it effect.
4. Press the SlideShow key to enter the Slide Show Mode. The fol-
lowing buttons are supported in the user interface:
65
English
User Controls
When the image
le is large, slide
show time will be
longer more than the
general picture, such
as BMP format. The
max size of image
le is as below:
- JPG: 10000 x
10000;
- TIF, BMP, GIF and
PNG: 1280 x 800;
• Stop: Stop Slide Show Mode.
• Delay 3/4/5: Slide Show delay in seconds.
• Slide Effect: Following modes are supported. (Slide Right/Slide
Down/Slide Up/Slide Auto)
• Repeat ON/OFF: Enable/Disable Slide Show Repeat Mode.
Press Up/Down/Left/Right key to choose different functions and
press Enter key to make it effect.
When the image can NOT be displayed due to memory limitation
or can NOT support image format, the specic image is displayed
on the center of the screen.
66
English
User Controls
How to use the Optoma Presenter
Optoma Presenter application allows remote desktop from a host
PC to be displayed on the network display through Ethernet, USB,
or Wireless transports. It can adapt to different network settings
(DHCP, xed IP, and direct link by USB/Ethernet cable).
This software can be downloaded from web page.
Before using this function, a USB cable is needed to connect the
Projector and PC Host directly. When the connection is OK, the PC
will show a USB device disk.
Select “Optoma Presenter”, and then run “autorun.exe” to start USB
Display.
1. Press the Autorun icon in the right-down region to pause or play the
USB display.
2. After installation in PC, double click the program of Optoma Pre-
senter to enter main window.
-->
• : Connect and search network display.
• : Stop/Start displaying desktop contents to connected network
display.
• : Select display region.
• : Congure Optoma Presenter.
• : Manage all connected network displays.
• : Disconnect all connections.
67
English
User Controls
Click the button to enter Connect and Search Menu.
1. Enter IP address of projector, select the option “Directly”, and then
click “Connect” button to enter log-in interface; or Click “Search”
button to search the projectors on network and select projectors
to connect.
2. Input “User type” and “Password” in log-in interface. Display port
can be selected, default is “Full screen”.
3. After log-in, Optoma Presenter will modify PC resolution to Ruby
supported resolution, and the buttons of and become
available.
Click the button to select the size of projection region, including
Full screen, Fixed Size and Alterable mode.
68
English
User Controls
• Fixed size mode: FIXED mode allows the user to place a frame
on the desktop and only the image enclosed inside the frame is
transferred to remote network display. The user can change the
width and height of the frame by setting up in page “Parameter
Setting”->”Basic Setting” or change the size of frame in ALTER-
ABLE mode and move the frame by dragging the frame with
mouse.
• Alterable size mode: ALTERABLE mode the only region capture
is the one enclose by the frame. The difference with FIXED
mode is the frame in ALTERABLE mode can be enlarged or
downsized by dragging the eight small black squares scattered
on eight edges of the frame.
Click the button to enter Setting interface, including Basic Set-
ting and Advanced Setting.
• Basic Setting: Select Language, Region size of xed size capture mode and allow notication message popup.
Click the button to control all the users and all the projectors
connected to the same projector.
69
English
User Controls
• : For Administrator user login.
• : For Normal user login.
• : Status of the connection for connected
• : Status of the connection for not connected.
• : For the status and display position of local screen on the
network display, change it by clicking on it and a dialog box appears.
• : Click this unlock icon, the password can be changed. (Password change to target network display, only a connection with an
Administrator user logged in can change the password.)
• : Click this lock icon will result in no response.
• : Disconnect with target network display.
• : Connect the target network display via a webpage front end.
User of Admin type is able to view a menu page with a list of PCs
connected to the target network display.
• : For the other PCs.
• : For the current PC.
• : Options of display port in which the highlight
one is the current status, click on one of them to change the
display port.
• : Disconnect the PC from a network display.
70
English
Appendices
Troubleshooting
If you experience a problem with your projector,
please refer to the following information. If a
problem persists, please contact your local
reseller or service center.
No image appears on-screen
Ensure all the cables and power connections are correctly and
securely connected as described in the “Installation” section.
Ensure all the pins of connectors are not bent or broken.
Check if the projection lamp has been securely installed. Please
refer to the “Replacing the lamp” section.
Make sure you have removed the lens cap and the projector is
switched on.
Ensure that the “AV mute” feature is not turned on.
Partial, scrolling or incorrectly displayed image
Press “Re-SYNC” on the remote.
If you are using a PC:
For Windows 95, 98, 2000, XP, Windows 7:
1. Open the “My Computer” icon, the “Control Panel” folder, and
then double click on the “Display” icon.
2. Select the “Settings” tab.
3. Verify that your display resolution setting is lower than or equal
to UXGA (1600 × 1200).
4. Click on the “Advanced Properties” button.
If the projector is still not projecting the whole image, you will also
need to change the monitor display you are using. Refer to the
following steps.
5. Verify the resolution setting is lower than or equal to UXGA
(1600 × 1200).
6. Select the “Change” button under the “Monitor” tab.
71
English
Appendices
7. Click on “Show all devices”. Next, select “Standard monitor
types” under the SP box; choose the resolution mode you need
under the “Models” box.
8. Verify that the resolution setting of the monitor display is lower
than or equal to UXGA (1600 × 1200).
If you are using a Notebook:
1. First, follow the steps above to adjust resolution of the
computer.
2. Press the appropriate keys listed below for your notebook
manufacturer to send signal out from notebook to projector.
Example: [Fn]+[F4]
Acer [Fn]+[F5]
Asus [Fn]+[F8]
Dell [Fn]+[F8]
Gateway [Fn]+[F4]
Mac Apple:
System Preference Display Arrangement Mirror
display
If you experience difculty changing resolutions or your monitor
freezes, restart all equipment including the projector.
The screen of the Notebook or PowerBook computer is not
IBM/Lenovo [Fn]+[F7]
HP/Compaq [Fn]+[F4]
NEC [Fn]+[F3]
Toshiba [Fn]+[F5]
displaying your presentation
If you are using a Notebook PC
Some Notebook PCs may deactivate their own screens when a
second display device is in use. Each has a different way to be
reactivated. Refer to your computer’s manual for detailed
information.
Image is unstable or ickering
Use “Phase” to correct it. See page 41for more information.
Change the monitor color setting on your computer.
Image has vertical ickering bar
Use “Frequency” to make an adjustment. See page 41 for more
information.
Check and re-congure the display mode of your graphic card to
make it compatible with the projector.
72
English
Appendices
Image is out of focus
Make sure the lens cap is removed.
Adjust the Focus Ring on the projector lens.
Make sure the projection screen is between the required distance.
See page 18.
The image is stretched when displaying 16:9 DVD title
When you play anamorphic DVD or 16:9 DVD, the projector will
show the best image when the projector display mode is set to
16:9 in the OSD.
If you play 4:3 format DVD titles, please change the format to 4:3
in the projector OSD.
If the image is still stretched, you will also need to adjust the
aspect ratio by referring to the following:
Please setup the display format as 16:9 (wide) aspect ratio type
on your DVD player.
Image is too small or too large
Move the projector closer to or further from the screen.
Press“Menu” button on the remote control or projector panel, go
to “DISPLAY Format” and try the different settings.
Image has slanted sides
If possible, reposition the projector so that it is horizontally
centered on the screen and below the bottom of the screen.
Press “Keystone +/-” button on the remote control or press
“ / ” on the projector panel, until the sides are vertical.
Image is reversed
Select “SETUP Projection” from the OSD and adjust the
projection direction.
73
English
Appendices
The projector stops responding to all controls
If possible, turn off the projector, then unplug the power cord and
wait at least 60 seconds before reconnecting power.
Check that “Keypad Lock” is not activated by trying to control the
projector with the remote control.
Lamp burns out or makes a popping sound
When the lamp reaches its end of life, it will burn out and may
make a loud popping sound. If this happens, the projector will not
turn on until the lamp module has been replaced. To replace the
lamp, follow the procedures in the “Replacing the Lamp” section on
pages 76-77.
LED lighting message
Steady light
No light
Message
Standby State
(Input power cord)
Power on (Warming)
Lamp lightingGreen
Power off (Cooling)
Error (Over Temp.)
Error (Fan fail)
Error (Lamp fail)
* POWER/STANDBY LED be ON when OSD appears, be OFF when OSD disappears.
POWER/STAND-
BY LED
(Green/Amber)(Red)(Red)
Amber
Flashing
Green
Flashing
Green
Flashing
Amber
Flashing
Amber
Flashing
Amber
Temp-LED
Flashing
Lamp-LED
74
English
Appendices
On Screen Messages
Temperature warning:
Fan failed:
Lamp warning:
Out of display range:
If the remote control does not work
Check the operating angle of the remote control is within ±15°
both horizontally and vertically of one of the IR receivers on the
projector.
Make sure there are not any obstructions between the remote
control and the projector. Move to within 7 m (±0°) of the projector.
Make sure the batteries are inserted correctly.
Replace batteries if they are exhausted.
75
English
Appendices
If the Interactive pen does not work
Check the input source is PC (VGA, HDMI, Wireless and LAN
source)
Check the Interactive function is turned On.
When using Wireless or LAN connection, and the Pen does not
work, check if the Wireless/Network function is turned On.
If more than one Pen point toward the screen at the same time,
none can function.
Check the Nib, If the Nib is worn out, replace with a new Nib.
Make sure the batteries are inserted correctly.
Replace batteries if they are exhausted.
Make sure there are not any obstructions between the Interactive
pen and the projector. Move to within 10m (0°) / 8m (20°) / 5m
(45°) of the projector.
76
English
Appendices
Replacing the lamp
The projector automatically detects the lamp life. When the
lamp life is nearing the end of use, you will receive a warning
message.
When you see this message, please contact your local reseller
or service center to change the lamp as soon as possible.
Make sure the projector has been cooled down for at least 30
minutes before changing the lamp.
Warning: If ceiling mounted, please use caution when
opening the lamp access panel. It is recommended to wear
safety glasses if changing the bulb when ceiling mounted.
“Caution must be used to prevent any loose parts from fall-
ing out of projector.”
Warning: Lamp compartment may be hot! Allow it to cool
down before changing the lamp!
Warning: To reduce the risk of personal injury, do not drop
the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.
77
English
Appendices
The screws on the
1
2
3
4
lamp cover and the
lamp cannot be
removed.
The projector
cannot be turned
on if the lamp
cover has not been
placed back on the
projector.
Do not touch the
glass area of the
lamp. Hand oil can
cause the lamp to
shatter. Use a dry
cloth to clean the
lamp module if it
was accidentally
touched.
Lamp Replacement Procedure:
1. Switch off the power to the projector by pressing the “ ” button.
2. Allow the projector to cool down for at least 30 minutes.
3. Disconnect the power cord.
4. Unscrew the two screws on the cover. 1
5. Lift up and remove the cover. 2
6. Unscrew the two screws on the lamp module. 3
7. Lift up the lamp handle and remove the lamp module slowly and carefully. 4
To replace the lamp module, reverse the previous steps.
8. Turn on the projector and use “Lamp Reset” after the lamp module is
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------BaudRate:9600Note:Thereisa<CR>afterallASCIIcommandsDataBits:80DistheHEXcodefor<CR>inASCIIcodeParity:NoneStopBits:1FlowControl :NoneUART16550FIFO:DisableProjectorReturn(Pass):PProjectorReturn(Fail):FXX=01ˀ99,projector'sID,XX=00is forallprojectors
Note : the ~XX must be set as ~00 when use on telnet command no matter what ID pro jector has.eg: telnet with ~0004 1 can execute Freeze function but ~3804 1 can't.
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND to projector (telnet supported)
Unit A, 27/F Dragon Centre,
79 Wing Hong Street, +852-2396-8968
Cheung Sha Wan, +852-2370-1222
Kowloon, Hong Kong www.optoma.com.hk
China
5F, No. 1205, Kaixuan Rd., +86-21-62947376
Changning District +86-21-62947375
Shanghai, 200052, China www.optoma.com.cn
88
English
Appendices
Regulation & Safety Notices
This appendix lists the general notices of your projector.
FCC notice
This device has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This device generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this device does cause
harmful interference to radio or television reception, which can
be determined by turning the device off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television
technician for help.
Notice: Shielded cables
All connections to other computing devices must be
made using shielded cables to maintain compliance with
FCC regulations.
Caution
Changes or modications not expressly approved by the
manufacturer could void the user’s authority, which is
granted by the Federal Communications Commission, to
operate this projector.
89
English
Appendices
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian
ICES-003.
Remarque à l’intention des utilisateurs
canadiens
Cet appareil numerique de la classe B est conforme a la
norme
• R & TTE Directive 1999/5/EC (if product has RF function)
Disposal instructions
Do not throw this electronic device into the
trash when discarding. To minimize pollution
and ensure utmost protection of the global
environment, please recycle it.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.