Instruction Guide for Manual Pull-Down Screen
1
Description
Floating wall bracket
Aluminium casing
Sc reen fabric
Handle
Top panel
Upper hook
Baffle
Lower hook
Locking screw
Warnings
The warranty will only be valid if you follow the instructions below carefully! Improper use and care may cause
serious injury and/or damage!.
Make sure the Fixing screw be fastened when using the wall bracket, to avoid any damage.
Make sure the surface you have chosen for installing the screen is flat and secure.
Please read the following as any damage to the screen surface will impact the image's quality:
1. Do not touch the screen surface by hand.
2. Do not write or draw on the screen surface.
3. Do not poke the screen surface by finger or edge tools, as it may cause scratches or tears.
4. Do not use any detergent or cleaning products to clean the screen surface, please clean it with a soft cloth
and lukewarm water.
Retract the screen after every use.
Ensure the screen is level when it is wall-mounted installation, when the screen is spread, it should be
balanceable with the wall.
Do not pull two sides of the screen fabric by hands, do not fold the screen fabric.
To prevent unnecessary damage, the operation and maintenance of the screen should be done by adult.
6
Accessaries
Floating wall bracket(2pcs)
5 40mm Tapping screw & cap (8s ets)
Hanging bracket (2pcs)
M5x10 Screw (6pcs)
Instruction manual (1pc)
Ignoring the safety warnings may lead
to injuries or damaging the product.
Retract the screen after every use.
Leave it hanging for a long period may
cause screen fabric loose
Avoid hanging anything on the screen
as it may cause the screen to fall down.
Do not take apart and replace with unknown parts. If there are any problems, please contact your local dealer.
Product specifications are subject to change.
The screen should be installed at secure
place to avoid any accidents or the screen
falling down.
Please contact your local dealer for repair
or maintenance, and contact us if you have
any further questions. Avoid taking apart the
fixtures by yourself. Loose parts may cause
the screen fall down.
Operation
Installation
5
1.Lowering the screen:
Using the pull down handle, lower the screen with a gentle even action until desired height is reached.
The screen will stop when it reaches its maximum.
DO NOT A TTEMPT TO FORCE THE SCREEN LOWER THAN THIS POINT.
The screen will retract slightly before lock-ing in place.
2.Raising the screen:
Using the handle, pull down the s creen a small way, then allow the screen to raise quickly.
Caution: Do not let go of the ha ndle until the screen is fully retracted. Damage from retracting too rapidly
can occur. Do not allow the dropper bar to hit the screen case when retracting.
Picture 1 Picture 2
Take out all the parts from the packaging to ensure you have all necessary components.
There are three installation measures for this product, namely wall mount, ceiling mount and ceiling hang. The
installed distance can be changeable up to your needs via adjusting the slipper block, while the ideal position is the
mounting bracket is at its nearest point to the end cap, which can reduce unnecessary vibration or noise.
Wall and ceiling installation:
1. Mount the wall/ceiling brackets using the appropriate screws for your supporting material.
2. Ensure the brackets are horizontal and near the ends of the casing. Fasten to the wall or ceiling, not both.
( Figure 1) .
Figure 1
Installation Steps
a) Wood supporting materials: Drill in the 5 x 40 screws through the appropriate holes in the bracket
( Figure 2-3 ).
b) Concrete supporting materials: Install the anchors and drill in the 5 x 40
( Figure 4-5).
bracket holes.
screws into the appropriate
2
Wood wall installation
Figure 2 Figure 3
Wood ceiling installation
Concrete wall installation
Figure 4 Figure 5
Concrete ceiling installation
3 ( Figure 6-7 ). Loosen the locking screw to lower the bracket clamp all the way down.
Ceiling hang installation
Each end of the screen casing needs to be supported by a hook (not provided). Ensure that the suspension system
(cable and/or hook) can support the weight of the screen.
1. To drill two same holes with an electric drill horizontally with wall, then fasten hangers (unprovided) onto the
ceiling. ( Figure 12 )
3
Fixing screw
Figure 6 Figure 7
4. Mount the projection screen by sliding the casing grooves over the bracket hooks. ( Figure 8-9 )
Up groove
Down groove
Figure 8 Figure 9
5. Tighten the locking screw to clamp the screen securely in place. ( Figure 10-11 )
Baffle
A
1
Figure 12
2. Use three M5x10mm screws to fasten the hanging brackets, to the wall and ceiling brackets as shown.
( Figure 13-14)
Figure 13 Figure 14
3. Attach the wall and ceiling brackets to the casing as shown in figures 15 and 16.
2
4
Figure 10 Figure 11
Figure 15 Figure 16
4. Place hooks through the hanging brackets to suspend the projection screen as shown. See figure 17.
Figure 17
Loading...