Optoma Pico PK301 User Manual

FOCUS

CLASS 1 LED PRODUCT

ey e Sa f e t y Wa r n I n g S

Avoid staring/facing directly into

the projector beam at all times. Keep your back to the beam as much as possible.

A stick or laser pointer is recommended to avoid the need for the user to enter the beam.

When projector is used in a classroom, adequately supervise students when they are asked to point out something on the screen.

In order to minimize power, use room blinds to reduce ambient light levels.

Im p o r t a n t Sa f e t y In S t r u c t I o n

1. Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from over heating, it is recommended to install the projector in a location that does not block ventilation. As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the projector in an enclosure such as a book

case or a cabinet that restricts air ow.

2. Do not use the projector near water or

moisture. To reduce the risk of re and/

or electric shock, do not expose the projector to rain or moisture.

3. Do not install near heat sources such as radiators, heaters, stoves or any other

apparatus such as ampliers that emits

heat.

4. Do not use the projector in direct sunlight.

5. Do not use near any appliance

generating a strong magnetic eld.

6. Do not use the projector in areas susceptible to excessive dust and dirt.

7. Turn off the product before cleaning.

8. Turn off the product before removing the battery.

9. Disconnect the battery if the product is not being used for a long period of time.

10. Ensure that the ambient room temperature is within 5- 35°C.

11. Relative Humidity is 5 - 35°C, 80% (Max.), non-condensing.

12. Do not expose the battery to temperatures above +60°C (+140°F)

13. New or idle batteries can have shortterm reduced capacity. Fully charge the battery before initial use.

14. Do not put the battery into your mouth.

15. Do not let the battery contacts touch another metal object.

16. Do not drop, throw or try to bend your product.

17. May explode if disposed of in re.

18. Clean only with dry cloth.

19. Only use attachments/accessories specied by the manufacturer.

20. Do not use the unit if it has been physically damaged or abused. Physical

damage/abuse would be (but not

limited to):

▀■ Unit has been dropped. ▀■ Charger or plug has been damaged. ▀■ Liquid has been spilled on to the

▀■ Projector has been exposed to rain or

▀■ Something has fallen in the projector

Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please contact your local reseller or service center before you send the unit for repair.

21. Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short out parts that

could result in re or electric shock.

22. See projector enclosure for safety related markings.

23. The unit should only be repaired by appropriate service personnel.

24. Do not touch the projector for a long time while the projector is used.

25. CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type.

26. Dispose of Used Batteries According to the Instructions.

projector.

moisture.

or something is loose inside.

re g u l a t I o n & S a f e t y n o t I c e S

This appendix lists the general notices of your Projector.

FCC notice

This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

device and receiver.

• Connect the device into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

Notice: Shielded cables

All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.

Caution

Changes or modications not

expressly approved by the manufacturer could void the user’s authority, which is granted by the Federal Communications Commission, to operate this device.

Operation conditions

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

Notice: Canadian users

This Class B digital apparatus complies with Canadian ICES-003.

Remarque à l’intention des utilisateurs canadiens

Cet appareil numerique de la classe B est conforme a la

norme NMB-003 du Canada.

Declaration of Conformity for EU countries

1. this device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may cause undesired operation.

• EMC Directive 2004/108/EC (including

amendments)

• Low Voltage Directive 2006/95/EC

• R & TTE Directive 1999/5/EC (if product has

RF function)

DI S p o S a l o f o l D el e c t r I c a l & el e c t r o n I c eq u I p m e n t

(Applicable throughout the European Union and other European countries with separate collection programs)

This symbol found on your product or on its packaging, indicates that this product should not be treated as household waste when you wish to dispose of it. Instead, it should be handed over to an applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment and human health, which could otherwise be caused by inappropriate disposal of this product. The recycling of materials will help to conserve natural resources.

This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.

FOCUS

Universal

I/O

mini

HDMI

AV IN

DC IN

Audio out

Micro

USB

micro SD

pr o D u c t ov e r v I e W

1. Lens

2. Focus Dial

3. Battery Indicator

4. Auto Search Source Button

5. Enter Button

6. Navigation / Volume Button (up/ down/left/right)

7. Menu / Back Button

8. Through-hole for straps

9. IR Cover

10. VGA Input Connector

11. Speaker

12. Mini HDMI Connector

13. DC Input

14. AV Input Connector

15. Audio Out Connector

16. Mirco USB port

17. Power Button

18. microSD Card Slot

19. Battery Cover

20. Screw Hole for Tripod

pa c k a g e ov e r v I e W

<Note> The standard accessories may vary in each region due to different applications.

In S t a l l I n g t h e Ba t t e r y

1. Remove the battery cover. (

2. Insert the battery with the electrical

contacts facing those in the battery compartment. ()

3. Secure battery into place by

pushing it down on the opposite side from the electrical contacts. () Remove the battery by lifting it from the opposite side of the

Standard Accessory

1. Power adaptor with AC Plug

2. VGA cable

3. USB Male Cable

4. Battery

electrical contacts.

4. Slide the battery cover back into

place.()

5. AV Cable Optional Accessory

6. Mini HDMI Cable

7. Remote control

8. iPod Connection Kit a. USB Cable for iPod Connector b. iPod Cable c. iPod Connector

9. Component Cable

10. USB Female Cable

~

)

+ 4 hidden pages