Optoma OCM818W-RU Users Manual

Projector

Flush Mount

ABtUS SIGAPORE PTE LTD www.abtussingapore.com

Optoma www.optoma.com

Model: OCM818W-RU / OCM818B-RU

Revision 24/01/2014Patent Pending

User Operation Guide

IMPORTANT NOTES

● Thank you for purchasing the Projector Flush Mount. This bracket is suitable for most

projectors up to a load of 15kg (33 lbs).

● To ensure correct usage, please read this instruction manual thoroughly. Keep this manual for future

reference.

● BRACKETS SHOULD BE MOUNTED ONLY BY A QUALIFIED INSTALLER.

● User will be responsible for any injuries and damages that may arise from improper installation and

handing of Projector Flush Mounting Kit.

● Ensure all mounting screws are appropriately positioned and properly tighten/ fastened.

● Installers are to ensure customer’s safety during installtion.

● We reserve the right to amend or undertake any necessary changes without prior notice.

● Ensure the Ceiling can support the total weight of the Projector and the Projector Flush Mount.

● All bolts and screws must be used at the designated points as per installation instructions to prevent

damage to the projector unit, or injury.

● DO NOT install near an air conditioner or where there is excessive dust and smoke

SPECIFICATION

Net Weight : 1.2 kg ( 2.6 lbs)

Dimension : 168 x 138 x 126 mm (6.6” x 5.4” x 5”)

Load Capacity : 15 kg (33 lbs)

Please read these

instructions before

commencing installation

as faulty installation could

result in injury. Optoma

assumes no responsibility

for faulty installations.

Package Checklist (Each package should contain the parts listed and shown below)

Flush Mount Assembly (x1)

Parts Bag

Cross Recessed Screw A—I

M4 x 15 Cross Recessed Screw

M4 x 20 Cross Recessed Screw

M4 x 25 Cross Recessed Screw

M5 x 15 Cross Recessed Screw

M5 x 20 Cross Recessed Screw

M5 x 25 Cross Recessed Screw

M6 x 15 Cross Recessed Screw

M6 x 20 Cross Recessed Screw

M6 x 25 Cross Recessed Screw

1mm Washer

2mm Washer

4mm Washer

Bottom Spacer

M5 x 10 Socket Button Screw

Square Nut

Ceiling Plate

M4x6 Cross Recessed Screw

M8x65 Socket Cap Screw

M5x10 Socket Button Screw

4 pcs 4 pcs

M3 x 15 Cross Recessed Screw

M3 x 20 Cross Recessed Screw

M3 Flat Washer

Extension Bracket (50mm)

4 pcs

Tools Included

4 pcs

Tools Required for mount assembly

4 pcs

1. 1x Star / Philips Screw Driver

2. 1x 13mm Spanner

4 pcs

3mm Allen Key

6mm Allen Key

1 pc

4 pcs

Square Extension Bracket (100mm)

Bottom Spacer

Nut

Extension Bracket (50mm)

1mm, 2mm, 4mm Washers

*Speciﬁ cations are subject to changes without notice. 3

User Operation Guide

(A) Removing the Ceiling Plate from the Flush Mount Assembly:

1. Loosen the M4x6 (x2) Cross Recessed Screw with a screw driver

2. Remove the M8x55 Socket Cap Screw and Nylock Nut from the Flush Mount Assembly as shown.

3. Removing the Ceiling Plate from the Flush Mount Assembly.

M8x55 Socket Cap Screw

Ceiling Plate

M8 Nylock Nut

Screw driver

M4x6 Cross Recessed Screw

6mm Allen Key

+ 8 hidden pages