Page 1
Table of contents
Table of Contents ...................................................................................1
Usage Notice ..........................................................................................2
Safety Information .........................................................................................2
Precautions ...................................................................................................3
Eye Safety Warnings .....................................................................................5
Introduction ............................................................................................6
Product Features ...........................................................................................6
Package Overview ........................................................................................7
Product Overview .......................................................................................... 8
Main Unit ................................................................................................................ 8
Control Panel ......................................................................................................... 9
Connection Ports .................................................................................................10
Remote Control .................................................................................................... 11
Installation ............................................................................................ 12
Connecting the Projector .............................................................................12
Powering On/Off the Projector ....................................................................13
Powering On the Projector ................................................................................... 13
Powering Off the projector ................................................................................... 14
Warning Indicator ................................................................................................. 14
Adjusting the Projected Image ....................................................................15
Adjusting the Projector’s Height ........................................................................... 15
Adjusting the Projector’s Zoom / Focus ............................................................... 16
Adjusting Projected Image Size ........................................................................... 16
User Controls .......................................................................................17
Control Panel & Remote Control ................................................................. 17
On-screen Display Menus ........................................................................... 20
How to operate ....................................................................................................20
Menu Tree ............................................................................................................21
Image ................................................................................................................... 22
Display ................................................................................................................ 26
Setup ....................................................................................................................29
System ................................................................................................................. 32
Appendices ..........................................................................................36
Troubleshooting ...........................................................................................36
Image Problems .................................................................................................. 36
Intermission Problems ........................................................................................ 38
Projector Status Indication .................................................................................. 39
Remote Control Problems ...................................................................................40
Replacing the Lamp ....................................................................................41
Compatibility Modes .................................................................................... 42
RS232 Commands and Protocol Function List ...........................................43
Ceiling Mount Installation ............................................................................46
Optoma Global Offices ................................................................................ 47
Regulation & Safety notices ........................................................................49
English
1
Page 2
Usage Notice
Safety Information
The lightning flash with arrowheard within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of import operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH
VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE
CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Class B emissions limits
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Important Safety Instruction
1. Read these instructions –before using this projector.
2. Keep these instructions –for future reference.
3. Follow all instructions.
4. Install in accordance with the manufacturer’s instructions
A. Do not block any ventilation openings
To ensure reliable operation of the projector and to protect it from over-
heating, put the projector in a position and location that will not interfere with its proper ventilation. For example, do not place the projector
on a bed, sofa, carpet, or similar surface that may block the ventilation
openings. Do not put it in an enclosure, such as a bookcase or a cabinet
that may keep air from flowing through its ventilation openings.
B. Do not use this projector near water or moisture. To reduce the risk
of fire or electric shock, do not expose the projector to rain or moisture.
C. Do not install near any heat sources, such as radiators, heaters,
stoves or other apparatus (including amplifiers) that produce heat.
5. Clean only with a dry cloth.
6. Only use attachments/accessories specified by the manufacturer.
7. Refer all servicing to qualified service personnel. Servicing is required
when the projector has been damaged in any way:
▀■ Such as power supply cord or plug is damaged.
▀■ Liquid has been spilled or objects have fallen into the apparatus.
▀■ The projector has been exposed to rain or moisture, does not oper-
ate normally, or has been dropped.
Do not attempt to service this projector yourself. Opening or removing
covers may expose you to dangerous voltages or other hazards. Please
call Optoma to be referred to an authorized service center near you.
8. Do not let objects or liquids enter the projector –as they may touch
dangerous voltage points or short-out parts that could result in a fire or
electric shock.
9. See projector enclosure for safety related markings.
10. The projector should not be adjusted or repaired by anyone except
properly qualified service personnel.
2
Page 3
Precautions
Note
Note
Please follow all warnings, precautions and maintenance as recommended in this user’s guide.
Usage Notice
When the lamp reaches
the end of its life, the
projector will not
turn back on until the
lamp module has been
replaced. To replace
the lamp, follow the
procedures listed under
“Replacing the Lamp”
section on page 41.
▀■ Warning-
▀■ Warning-
▀■ Warning-
▀■ Warning-
▀■ Warning-
▀■ Warning-
▀■ Warning-
▀■ Warning-
▀■ Warning-
Do not look into the projector’s lens when the
English
lamp is on. The bright light may hurt your
eyes.
To reduce the risk of fire or electric shock, do
not expose this projector to rain or moisture.
Please do not open or disassemble the projector as this may cause electric shock.
When replacing the lamp, please allow unit to
cool down, and follow all replacement instructions. See page 41.
This projector will detect the life of the lamp
itself. Please be sure to change the lamp when
it shows warning messages.
Reset the “Lamp Reset” function from the onscreen display “System|Lamp Setting” menu
after replacing the lamp module (refer to page
35).
When switching the projector off, please
ensure the cooling cycle has been completed
before disconnecting power. Allow 90 seconds
for the projector to cool down.
Do not use lens cap when projector is in
operation.
When the lamp is approaching to the end
of its life time, the message “Replacement
suggested” will show on the screen. Please
contact your local reseller or service center to
change the lamp as soon as possible.
3
Page 4
Usage Notice
Do:
▀■ Turn off the product before cleaning.
▀■ Use a soft cloth moistened with mild detergent to clean the
display housing.
▀■ Disconnect the power plug from AC outlet if the product is not
being used for a long period of time.
Do not:
▀■ Block the slots and openings on the unit provided for ventila-
tion.
▀■ Use abrasive cleaners, waxes or solvents to clean the unit.
▀■ Use under the following conditions:
- Extremely heat, cold or humidity.
- In areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- In direct sunlight.
4
Page 5
Usage Notice
Eye Safety Warnings
▀■ Avoid staring directly into the projector beam at all times.
▀■ Minimize standing facing into the beam. Keep your back to
the beam as much as possible.
▀■ A stick or laser pointer is recommended to avoid the need for
the user to enter the beam.
▀■ Ensure that projectors are located out of the line of sight from
the screen to the audience; this ensures that, when presenters
look at the audience, they do not also have to stare at the projector lamp. The best way to achieve this is by ceiling-mounting rather than floor or table-mounting the projector.
▀■ When projector is used in a classroom, adequately supervise
students when they are asked to point out something on the
screen.
English
▀■ In order to minimize the lamp power needed, use room blinds
to reduce ambient light levels.
5
Page 6
Introduction
Product Features
This product is a 1080p single chip 0.95” DLP® projector. Outstanding features include:
▀■ Native 16:9 1080p DLP® Technology
▀■ Complete 10-bit video processing (decoding, deinterlac-
ing, scaling, image enhancement and color)
▀■ Use 7 segment color wheel R/G/B/ND/R/G/B cycle
▀■ PixelWorksTM video processor chip
▀■ Studio-grade 480i/576i Standard Definition de-interlac-
ing and 1080i High Definition de-interlacing
▀■ Video Compatibility:
▪ 480i-NTSC, NTSC4.43
▪ 576i-PAL/PAL-M/PAL-N/SECAM
▪ SDTV compatible (480i/p, 576i/p)
▪ HDTV compatible (720p, 1080i/p)
▪ RGB signal: HD, XGA, SVGA, VGA res-sizing
▀■ Macintosh compatible
▀■ Full function IR remote control with back light
▀■ Advanced vertical digital keystone correction and high
quality full screen image re-scaling
▀■ User friendly control panel
▀■ Optoma’s patent-pending O2AirTM Photo Catalyst air
purification technology
▀■ HDMI & DVI support HDCP function.
▀■ HDMI(support HDMI 1.3) x2, DVI-I (support HDMI 1.1,
SCART, HDTV) x1, YPbPr (RCA) x1, S-Video x1, Composite x1
6
Page 7
Introduction
Note
Note
Package Overview
This projector comes with all the items shown below.
Check to make sure your unit is complete. Contact your
dealer immediately if anything is missing.
English
Due to the difference
in applications for each
country, some regions
may have different accessories.
Projector with lens cap
RCA Component Cable
for YPbPr 2.0m
Available in European version only
SCART RGB/S-Video
Adaptor
Documentation :
User’s Manual
Warranty Card
Quick Start Card
Power Cord 1.8m
IR Remote Controller
DVI to VGA Adaptor
RS232 Cable 1.8m
2 x AA Batteries
VGA Cable 1.8m
7
Page 8
Introduction
Product Overview
Main Unit
10
11
1
2
3
4
5
5
10
7
6
7
8
7
5
1
10
9
1. Control Panel
2. Zoom Lever
3. Focus Ring
4. Elevator Button (one on each side)
5. Elevator Feet
6. Zoom Lens
7. IR Receivers
8. Connection Ports
9. Power Socket
10. Tilt-Adjustment Feet
11. Air exhaust vent
8
Page 9
Control Panel
Introduction
1
1. Power and IR Receiver
2. Power Indicator LED
3. Lamp Indicator LED
4. Temp Indicator LED
5. Menu (On/Off)
6. Four Directional Select Keys
7. Source Select
8. Re-Sync
9. Enter
2
5 7
6
43
English
8 9
9
Page 10
Introduction
Connection Ports
2 3 7
8
1. +12V Relay Connector
2. Composite Video Input Connector
3. RS232 Input Connector
4. S-Video Input Connector
5. DVI-I Input Connector (PC Digital and DVI-HDCP)
6. HDMI 1 Connector
7. HDMI 2 Connector
8. Component Video Input Connector
9. Power Socket
10. Kensington MicrosaverTM Lock Port
6541
9
10
10
Page 11
Remote Control
1. Power (On/Off)
2. Contrast
3. Gamma
4. Brite Mode
5. Image Shift
6. Enter
7. Four Directional Select
Keys
8. Display Mode
9. Edge Mask
10. Brightness
11. Image AI
12. IRIS
13. Menu
14. Overscan
15. 4:3
16. 16:9
17. HDMI1 Source
18. YPbPr Source
19. Letter-Box
20. Native
21. DVI Source
22. Composite Video
Source
23. HDMI2 Source
24. S-Video
Introduction
1
10
11
12
13
14
15
16
17
18
24
23
2
3
4
5
6
7
68
9
19
20
21
22
English
11
Page 12
Installation
Note
Note
Connecting the Projector
SCART DVD Player
+12V Relay Output
Video Output
DVD Player, Set-top Box,
HDTV receiver
7
RGB
DVI
8
3
2
4
5
6
9
1
10
S-Video Output
Due to the difference
in applications for each
country, some regions
may have different accessories.
12
1. .............................................................................................................Power Cord
2. ...................................................... DVI to VGA Adaptor (For European Only)
3. ............................................................................................................ RS232 Cable
4. ..................................................Composite Video Cable (Optional Accessory)
5. ......................................................................RCA Component Cable for YPbPr
6. ...................................................................S-Video Cable (Optional Accessory)
7. ......................................SCART RGB/S-Video Adaptor (For European Only)
8. ........................................................................ VGA Cable (For European Only)
9. ......................................................................... DVI Cable (Optional Accessory)
10. ................................................................... HDMI Cable (Optional Accessory)
Page 13
Installation
Note
Note
Powering On/Off the Projector
Powering On the Projector
Turn on the projector
first and then select the
signal sources.
1. Remove the lens cap.
2. Ensure that the power cord and signal cable are securely
connected. The Power LED will turn red.
3. Turn on the lamp by pressing “ ” button on the control
panel. And the Power LED will turn blue.
The startup screen will display in approximately 30 seconds.
The first time you use the projector, you can select your
preferred language from quick menu after the startup screen
display.
4. Turn on your source (computer, notebook, video player,
etc.). The projector will detect your source automatically
within “Setup” menu, check that “Source Lock” has been set
to “Off”.
▀■ If you connected multiple sources at the same time, press the
“Source” button on the control panel or direct source key on
the remote control to switch between inputs.
English
21
13
Page 14
Installation
Powering Off the Projector
1. Press the “ ” button to turn off the projector lamp, you will
see a message displayed on the projector’s screen.
Press the “ ” button again to confirm, otherwise the message will disappear after 5 seconds.
2. The cooling fans continue to operate for about 60 seconds for
cooling cycle and the Power LED will flash blue. When the
lights solid red, the projector has entered standby mode.
If you wish to turn the projector back on, you must wait
until the projector has completed the cooling cycle and has
entered standby mode. Once in standby mode, simply press
“ ” button to restart the projector.
3. Disconnect the power cord from the electrical outlet and the
projector.
4. Do not turn on the projector immediately following a power
off procedure.
14
Warning Indicator
▀■ When the “LAMP” indicator lights solid red, the projector
will automatically shut itself down. Please contact your local
reseller or service centre. See page 47.
▀■ When the “TEMP” indicator flashes red, it indicates the pro-
jector has overheated. The projector will automatically shut
itself down.
Under normal conditions, the projector can be switched on
again after it has cooled down. If the problem persists, you
should contact your local dealer or our service center. See
page 47.
▀■ When the “LAMP” indicator flashes red, it indicates the fan
has failed. Please contact your local dealer or our service
centre. See page 47.
Page 15
Installation
Adjusting the Projected Image
Adjusting the Projector’s Height
The projector is equipped with elevator feet for adjusting the
image height.
To raise the image:
1. Press the elevator button .
2. Raise the image to the desired height angle , then release
the button to lock the elevator feet into position.
3. Use screw in feet to fine-tune the display angle.
To lower the image:
1. Press the elevator button.
2. Lower the image, then release the button to lock the elevator feet into position.
3. Use screw in feet to fine-tune the display angle.
English
Elevator Button
Elevator Feet
Tilt-Adjustment Feet
1
2
3
15
Page 16
Installation
L
H'
H
(1920X1080)
A
B(1920X1080)
W0 (1920X1080)
W1 (1440X1080)
D(1920X1080)
Adjusting the Projector’s Zoom / Focus
Turn the Zoom Lever to zoom in or zoom out. To focus the
image, turn the focus ring until you see a clear image. The
projector will focus at distances from 4.9 to 39.4 feet (1.5 to
12.0 meters) and the projection screen size from 0.775m~7.62m
(30.5”~300”) at 16:9 mode with mechanical travel.
Zoom Lever
Focus Ring
Adjusting Projection Image Size
Side View Front View
16
Throw Ratio (TR)=1.85 as Wide mode
A=6.25°
H'=L X tan(A) W1 (1440x1080)=W0 (1920x1080) X 0.75
H (1920x1080)=W0 (1920x1080) X 0.56 H (1440x1080)=W1 (1440x1080) X 0.75
Display Format A B
16:9 (1920x1080) 6.25 22.47 245.73 132.83 74.72 26.90 152.40 60.00
4:3 (1440x1080) 6.25 22.47 245.73 99.62 74.72 26.90 124.53 49.03
Projection Distance (M) 2.0 2.5 3.0 3.5 4.0 5.0 6.0
Screen Size 16:9
(inch)
Screen Size 4:3
(inch)
B
(1920x1080)=22.47°
Max 48.8 61.0 73.3 85.5 97.7 122.1 146.5
Min 40.7 50.9 61.0 71.2 81.4 101.7 122.1
Max 39.9 49.9 59.9 69.8 79.8 99.8 119.7
Min 33.3 41.6 49.9 58.2 66.5 83.1 99.8
W0 (1920x1080)=L/TR
L
(cm)W (cm)H (cm)H’(cm)D (cm)
D’
(in)
Page 17
User Controls
Control Panel & Remote Control
There are two ways for you to control the functions: Control
Panel and Remote Control.
Using the Control Panel
Power
Source
Menu
Four Directional Select
Keys
Enter
Re-Sync
Refer to the “Power On/Off the Projector”
section on pages 13-14.
Press “Source” to choose DVI, RGB, Component-p, Component-i, S-Video, Composite Video, HDTV and HDMI sources.
Press “Menu” to launch the on-screen
display (OSD) menu. To exit OSD, Press
“Menu” again.
Use to select items or make
adjustments to your selection.
Confirm your item selection.
Automatically synchronizes the projector to
the input source.
English
17
Page 18
User Controls
Using the Remote Control
Power
Brightness
Contrast
Image AI
Gamma
IRIS
Brite Mode
/
Image Shift
Edge Mask
Mode
Menu
Four Directional Select
Keys
Refer to the “Power On/Off the Projector”
section on pages 13-14.
Adjust the brightness of the image.
Control the degree of difference between
the lightest and darkest parts of the picture.
Switch the Image AI function ON/OFF.
(refer to page 32-33)
There are 10 preset gamma curves. After
the initial setup and fine tuning is completed, utilize the Gamma Adjustment steps to
optimize your image output.
Refer to “IRIS” function on page 33 for
more information.
Increase the brightness of the image. (refer
to page 35).
Shifts the projected image position vertically.
Choose “On” to mask off a few pixels on
each edge of the image to be displayed. Use
Edge Mask “On” if image source happens
to have encoding error near any edge of the
displayable image.
Select the display mode from Cinema,
Bright, TV, sRGB and User.
Press “Menu” to launch the on-screen
display (OSD) menu. To exit OSD, Press
”Menu” again.
Use to select items or make adjustments to your selection.
18
Enter
Overscan
4:3
Confirm your item selection.
Mask off a few pixels on each edge of the
image to be displayed. Use this function
to adjust if image source happens to have
noise near any edge of the display image.
Scale the image at a 4:3 aspect ratio.
Page 19
User Controls
16:9
Native
Letter-Box
DVI
HDMI1
HDMI2
YPbPr
Video
S-Video
Scale the image at a 16:9 aspect ratio.
The input source will be displayed without
scaling.
Enable the viewing of the letterboxed nonanamorphically enhanced movie at full
screen width. Part of the original image will
be lost if the image aspect ratio is less than
2.35:1.
Press “DVI” to choose Analog and Digital
Signal source from DVI connector.
Press “HDMI1” to choose source from
HDMI1 connector.
Press “HDMI2” to choose source from
HDMI2 connector.
Press “YPbPr” to choose Component video
source.
Press “Video” to choose Composite video
source.
Press “S-Video” to choose S-video source.
English
19
Page 20
User Controls
On-screen Display Menus
The Projector has multilingual On-screen Display menus that
allow you to make image adjustments and change a variety of
settings. The projector will automatically detect the source.
How to operate
1. To open the OSD menu, press “Menu” on the Remote Control or
Control Panel.
2 When OSD is displayed, use keys to select any item in the
main menu. While making a selection on a particular page, press
or “Enter” key to enter sub menu.
3. Use keys to select the desired item and adjust the settings
by key.
4. Select the next item to be adjusted in the sub menu and adjust as
described above.
5. Press “Enter” or “Menu” to confirm, and the screen will return to
the main menu.
6. To exit, press “Menu” again. The OSD menu will close and the
projector will automatically save the new settings.
20
Main Menu
Sub Menu
Setting
Page 21
Menu Tree
1 English
V Ima
g
e Shif
t
Edge Mas
k
Advanced
Shar
p
ness
Noise Reduction
IMAGE Mode
Tint
IMAGE|Advanced
Cinema/Bri
g
ht/TV/sRGB/Use
r
Contrast
Bri
g
htness
Color
Warm
Gamma
Film/Video/Gra
p
hics/PC
True Vivid
Ed
g
e Enhanc
e
B/W Extension
Color Tem
p
Degamma
DISPLAY
H Ima
g
e Shif
t
V Keystone
Overscan
Mid
User:Red Gain/Green Gain/
Blue Gain/Red Bias/
Green Bias/Blue Bias
Cold
Format
16:9/4:3/LBX/Native
Off
(0)/(
1~5
)
Off(0)/(1~2
)
On(1)/Off(0
)
1 English
Current/All
IRIS On/
(
1~16)Off
On/Off
Reset
Ima
g
e AI
Menu LocationSYSTEM
Phase/Trackin
g
/H Position/V Position
Y Gain/Pb Gain/Pr Gain/
Y Bias/Pb Bias/Pr Bias
High Altitude On/Off
Si
g
nal
V Ima
g
e Shif
t
Edge Mas
k
English/Deutsch/Français/Italiano/Español/
Português/Polski/Nederlands//
Suomi/Svenska/Norsk/Dansk/
/
/
/
/
HDMI 1/HDMI 2/DVI-Digital/DVI-Analog/
DVI-SCART/Component/S-Video/Video
On/Off
Auto Power Of
f
Language
Source Lock
SETUP
Advanced
Shar
p
ness
Noise Reduction
IMAGE Mode
Tint
IMAGE|Advanced
Cinema/Bri
g
ht/TV/sRGB/Use
r
Contrast
Bri
g
htness
Color
Warm
Gamma
Film/Video/Gra
p
hics/PC
True Vivid
Ed
g
e Enhanc
e
B/W Extension
Color Tem
p
Degamma
DISPLAY
12V Tri
gger
Lamp Settin
g
Projection
H Ima
g
e Shif
t
V Keystone
In
p
ut Source
Overscan
Mid
User:Red Gain/Green Gain/
Blue Gain/Red Bias/
Green Bias/Blue Bias
Cold
Color S
p
ace RGB/YCbCr
Format
White Level/Black Level/Saturation/Tin
t
16:9/4:3/LBX/Native
Lam
p
Reminde
r
Background Dark Blue/Black/Gray/Start Logo
STD/LBX
Test Pattern Grid/White Pattern/Non
e
Exit
Off
(0)/(
1~5
)
Off(0)/(1~2
)
On(1)/Off(0
)
On/Off
Brite Mode On/Off
SYSTEM|Lamp Settin
g
Lamp Hour
Lam
p
Reset Yes/No
1 English
Phase/Trackin
g
/H Position/V Position
High Altitude On/Off
Si
g
nal
V Ima
g
e Shif
t
Edge Mas
k
English/Deutsch/Français/Italiano/Español/
Português/Polski/Nederlands//
Suomi/Svenska/Norsk/Dansk/
/
/
/
/
HDMI 1/HDMI 2/DVI-Digital/DVI-Analog/
DVI-SCART/Component/S-Video/Video
On/Off
Auto Power Of
f
Language
Source Lock
SETUP
Advanced
Shar
p
ness
Noise Reduction
IMAGE Mode
Tint
IMAGE|Advanced
Cinema/Bri
g
ht/TV/sRGB/Use
r
Contrast
Bri
g
htness
Color
Warm
Gamma
Film/Video/Gra
p
hics/PC
True Vivid
Ed
g
e Enhanc
e
B/W Extension
Color Tem
p
Degamma
DISPLAY
H Ima
g
e Shif
t
V Keystone
In
p
ut Source
Overscan
Mid
User:Red Gain/Green Gain/
Blue Gain/Red Bias/
Green Bias/Blue Bias
Cold
Format
16:9/4:3/LBX/Native
Off
(0)/(
1~5
)
Off(0)/(1~2
)
On(1)/Off(0
)
1 English
Current/All
Reset
Phase/Trackin
g
/H Position/V Position
Y Gain/Pb Gain/Pr Gain/
Y Bias/Pb Bias/Pr Bias
High Altitude On/Off
Si
g
nal
V Ima
g
e Shif
t
Edge Mas
k
English/Deutsch/Français/Italiano/Español/
Português/Polski/Nederlands/
/
Suomi/Svenska/Norsk/Dansk/
/
/
/
/
HDMI 1/HDMI 2/DVI-Digital/DVI-Analog/
DVI-SCART/Component/S-Video/Video
On/Off
Auto Power Of
f
Language
Source Lock
SETUP
Advanced
Shar
p
ness
Noise Reduction
IMAGE Mode
Tint
IMAGE|Advanced
Cinema/Bri
g
ht/TV/sRGB/Use
r
Contrast
Bri
g
htness
Color
Warm
Gamma
Film/Video/Gra
p
hics/PC
True Vivid
Ed
g
e Enhanc
e
B/W Extension
Color Tem
p
Degamma
DISPLAY
H Ima
g
e Shif
t
V Keystone
In
p
ut Source
Overscan
Mid
User:Red Gain/Green Gain/
Blue Gain/Red Bias/
Green Bias/Blue Bias
Cold
Color S
p
ace RGB/YCbCr
Format
White Level/Black Level/Saturation/Tin
t
16:9/4:3/LBX/Native
Off
(0)/(
1~5
)
Off(0)/(1~2
)
On(1)/Off(0
)
User Controls
White Level/Black Level/Saturation/Hue/IRE
English
21
Page 22
User Controls
Note
Note
Mode
There are many factory presets optimized for various types of images.
Cinema: For home theater.
Bright: For the brightest possible image, Use if ambient light is
present.
“Image mode-->TV”
will support automatically “Overscan” with
step “2” as default.
TV: For watching analogue or digital TV images.
sRGB: For standard color.
User: Memorize user’s settings.
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast changes the
amount of black and white in the image.
Press the to decrease the contrast.
Press the to increase the contrast.
Brightness
Adjust the brightness of the image.
Press the to darken image.
Press the to lighten the image.
Color
Adjusts a video image from black and white to fully saturated color.
Press the to decrease the amount of color in the image.
Press the to increase the amount of color in the image.
Image
22
Page 23
User Controls
Tint
Adjusts the color balance of red and green.
Press the to increase the amount of green in the image.
Press the to increase the amount of red in the image.
Sharpness
Adjusts the sharpness of the image.
Press the to decrease the sharpness.
Press the to increase the sharpness.
English
23
Page 24
User Controls
Note
Note
Noise Reduction
The motion Adaptive Noise Reduction reduces the amount of visible noise interlaced signals. The range is from “0” to “10”. (0:Off)
Gamma
This unit comes with 10 preset gamma curves. After the initial setup
and fine tuning is completed, utilize the Gamma Adjustment steps
to optimize your image output.
Degamma
This allows you to choose a degamma table that has been fine-tuned
to bring out the best image quality for the input.
Film: For home theater.
Video: For video or TV source.
Graphics: For image source.
PC: For PC or computer source.
True Vivid
This adjustable item utilizes a new color-processing algorithm and
enhancements to enable the picture’s vividness to be significantly
increased. The range is from “0” to “5”.
Edge Enhance
There are 3 pre-set modes and one user mode for advanced edge
enhancement filter. You can easily switch between the modes to
“B/W Extension” can’t
support when source is
HDMI, analog or digital RGB via DVI port.
achieve different effects. (0:Off)
B/W Extension
Black and White Extension can stretch the black and white levels to
automatically increase the contrast of input image. This unit has 2
Image | Advance
24
Page 25
User Controls
pre-set modes that allow the user to switch among the pre-sets to
obtain different image effects. (0:Off/1:On)
Color Temp.
Adjust the color temperature. At cold temperature, the screen
looks colder; at warm temperature, the screen looks warmer.
1) For User mode adjustment, put cursor on “User”, and press
“Enter” to select this adjustment item.
2) Use “ ”, “ ” to highlight the desired adjustment items, then
press “Enter” or “ ” to select it. The Menu disappears and
only an adjustment bar appears.
3) Use “ ”, “ ” arrow keys to adjust image.
English
25
Page 26
User Controls
Format
Use this function to choose your desired aspect ratio.
4:3: This format is for 4x3 input sources not enhanced for Wide-
screen TV.
16:9: This format is for 16x9 input sources, like HDTV and DVD
enhanced for Widescreen TV.
Native: This format displays the original image without any scal-
ing.
Input Signal
Display
Display area
Picture area
Display on Screen
26
Page 27
(*) Each I/O has differ-
Note
Note
ent setting of “Overscan”.
(*) “Image mode-->TV”
will support automatically “Overscan” with
step “2” as default.
(*) “Overscan” and
“Edge mask” can’t
work at same time.
(*) “H Image shift” only
support in format “4:3”
and “Native”. If source
is 1080i/p, “H Image
shift” only support in
format “4:3”.
User Controls
LBX: This format is for non-16x9, letterbox source and for
users who use external 16x9 lens to display 2.35:1 aspect ratio
using full resolution.
Detail informations about LBX mode :
1. Some Letter-Box DVDs are not enhanced for 16x9 TVs. In
this situation, the image will not look right when displayed in 16:9 mode.
In this situation, please try to using the 4:3 mode to view
the DVD.
But if the content itself is not 4:3, it will have black bars
around the image in a 16:9 display. For this kind of content, you can use LBX mode to fill the image in the 16x9
display as much as possible.
2. If you use an external 16x9 lens, this LBX mode also allows
you to watch a 2.35:1 content (include Anamorphic DVD
and HDTV film source) that support anamorphic wide is
enhanced for 16x9 Display in a wide 2.35:1 image.
In this case, there are no black bars, the full lamp power
and vertical resolution is fully utilized for maximum viewing effects.
Other than these two occasions, one should stay with 16:9
and 4:3 modes for most viewing experiences.
Overscan
Overscan function removes the noise in a video image. Overscan
the image to remove video encoding noise on the edge of video
source.
Edge Mask
Press the to reduce the size of an image.
Press the to magnify an image on the projection screen.
H Image Shift
Shifts the projected image position horizontally.
V Image Shift
Shifts the projected image position vertically.
English
27
Page 28
User Controls
V Keystone
Press the or to adjust image distortion vertically and makes a
squarer image.
28
Page 29
User Controls
Setup
Language
Choose the multilingual OSD menu. Press or into the sub
menu and then use the or key to select your preferred language. Press “Select (Enter)” to finalize the selection.
Input Source
Enable input sources. Press or into the next menu as below and
then use or to select. Press “Select (Enter)” to finalize the selection. The projector will not search inputs that are de-selected.
English
Source Lock
When this function is turned off, the projector will search for other
signals if the current input signal is lost. When this function is
turned on, it will search for a specified connection port.
29
Page 30
User Controls
Note
Note
High Altitude
Choose “On” to turn on High Altitude mode. Operates the fans at
full speed continuously to allow for proper high altitude cooling of
the projector.
Auto Power Off
Sets the interval of power-off of the system, if there is no signal
input. (In minutes)
RGB/HDTV Source Video Source
Signal
Phase: Changes the display data frequency to match the fre-
quency of your computer’s graphic card. When you experience a
vertical flickering bar, use this function to make an adjustment.
Tracking : Synchronizes the signal timing of the display with the
graphics card. If you experience an unstable or flickering image,
use this function to correct it.
H Position: Adjusts the horizontal position.
“Signal” don’t support
when source is HDMI
or DVI-D.
V Position: Adjusts the vertical position.
White Level : Allow user adjust White Level when inputting S-
Video or Video/CVBS signals.
Black Level : Allow user adjust Black Level when inputting S-
Video or Video/CVBS signals.
Saturation : Adjusts a video image from black and white to fully
saturated color. Press the to decrease the amount of color in
the image. Press the to increase the amount of color in the image.
30
Page 31
“IRE” only support
Note
Note
under NTSC signal.
User Controls
Hue : Adjusts the color balance of red and green. Press the
to increase the amount of green in the image. Press the to
increase the amount of red in the image.
IRE : Adjusts measurement of composite video signals.
Color Space
Select an appropriate color matrix type from RGB or YCbCr.
Reset
Return the adjustments and settings to factory default values.
Current : Returns the current menu’s settings to factory default.
All : Returns the settings for all menus to factory default values.
English
31
Page 32
User Controls
Menu Location
Choose the menu location on the display screen.
Projection
Front-Desktop
The factory default setting.
System
32
Rear-Desktop
When you select this function, the projector reverses the image
so you can project behind a translucent screen.
Front-Ceiling
When you select this function, the projector turns the image
upside down for ceiling-mounted projection.
Rear-Ceiling
When you select this function, the projector reverses and turns
the image upside down at same time. You can project from behind a translucent screen with ceiling mounted projection.
Image AI
Image AI improves the contrast of the picture by optimizing the
brightness of the lamp according to the picture content.
On: The dynamic image performance manager is active in mak-
ing sure your greatest pleasure from seeing a movie dynamically
Page 33
User Controls
with the most dark details revealed, vivid and bright image
performed all the way.
Off: The dynamic image performance manager is on standby.
IRIS
The iris function adjusts the contrast optically by opening and
closing the lens aperture. The iris can be switched between Off
(Close) and On (Open).
When you press the IRIS button, the current setting appears. When
pressing it again while the setting is being displayed, the setting can
be changed. It takes about 6 seconds for the iris to shift between Off
(0) state and On (1-16) state.
1-16: When 1-16 steps is selected, black levels of the image are
reproduced with more clarity though the brightness is lowered.
There are 16 step for you adjust.
0: When 0 is selected, the image becomes brighter.
Test Pattern
Displays a test pattern. There are Grid, White pattern and None.
Background
Use this feature to display a “Dark Blue”, “Black”, “Gray”or “Start
Logo” screen when no signal is available.
English
33
Page 34
User Controls
12V Trigger
STD: When “STD” is selected, 12V Trigger will send 12V when
projector turn on.
LBX: When 12V trigger set as “LBX” --
1. Format change to “LBX”,12V trigger port will send 12V.
2. Format is “4:3”, “16:9”, or “Native”, 12V trigger port won’t
send 12V, it will be 0V.
34
Page 35
User Controls
System| Lamp
Setting
Lamp Hour
Displays the cumulative lamp operating time.
Lamp Reminder
Choose this function to show or to hide the warning message when
the changing lamp message is displayed. The message will appear
up 30 hours before suggested replacement of lamp.
Brite Mode
Choose “On” to increase the brightness. Choose “Off” to return
normal mode.
Lamp Reset
Reset the lamp life hour after replacing the lamp.
English
35
Page 36
Appendices
Note
Note
Troubleshooting
If you experience a problem with your projector, please
refer to the following information. If a problem persists,
please contact your local reseller or service center. (See
page 47 for details)
Image Problems
No image appears on-screen
Ensure all the cables and power connections are correctly and
securely connected as described in the “Installation” section.
Ensure the pins of connectors are not crooked or broken.
Check if the projection lamp has been securely installed. Please
refer to the “Replacing the lamp” section.
Make sure you have removed the lens cap and the projector is
switched on.
Partial, scrolling or incorrectly displayed image
Press “Re-Sync” on the control panel.
If you are using a PC:
For Windows 95, 98, 2000, XP:
1. From the “My Computer” icon, open the “Control Panel” folder,
and double click the “Display” icon.
(*) The resolution:
HDMI’s 1920 x 1080 i/p
and component’s 1920 x
1080 i is recommended
for this projector.
2. Select the “Settings” tab.
3. Verify that your display resolution setting is lower than UXGA
(1600 x 1200). (*)
4. Click on the “Advanced Properties” button.
If the projector is still not projecting the whole image, you will
also need to change the monitor display you are using. Refer to
the following steps.
5. Verify the resolution setting is lower than or equal to UXGA
(1600 x 1200) resolution. (*)
36
Page 37
(*) The resolution:
Note
Note
HDMI’s 1920 x 1080 i/p
and component’s 1920 x
1080 i is recommended
for this projector.
Appendices
6. Select the “Change” button under the “Monitor” tab.
7. Click on “Show all devices.” Next, select “Standard monitor
types” under the SP box; choose the resolution mode you need
under the “Models” box.
8. Verify that the resolution setting of the monitor display is lower
than or equal to UXGA (1600 x 1200). (*)
If you are using a Notebook:
1. First, follow the steps above to adjust resolution of the computer.
2. Press the toggle output settings. Example: [Fn]+[F4]
English
Compaq=> [Fn]+[F4]
Dell => [Fn]+[F8]
Gateway=> [Fn]+[F4]
IBM=> [Fn]+[F7]
Mac Apple:
System Preference-->Display-->Arrangement-->Mirror
display
If you experience difficulty changing resolutions or your monitor
freezes, restart all equipment including the projector.
The screen of the Notebook or PowerBook computer is not
Hewlett
Packard
NEC=> [Fn]+[F3]
Toshiba => [Fn]+[F5]
=> [Fn]+[F4]
displaying your presentation
If you are using a Notebook PC:
Some Notebook PCs may deactivate their own screens when a
second display device is in use. Each has a different way to be reactivated. Refer to your computer’s manual for detailed information.
Unstable or flickering image
Use “Tracking” to correct it. See page 30 for more information.
Change the monitor color setting on your computer.
Image has vertical flickering bar
Use “Phase” to make an adjustment. See page 30 for more informa-
tion.
Check and reconfigure the display mode of your graphic card to
make it compatible with the projector.
37
Page 38
Appendices
Image is out of focus
Make sure the Lens cap is removed.
Adjusts the Focus Ring on the projector lens.
Make sure the projection screen is between the required dis-
tance 4.9 to 39.4 feet (1.5 to 12.0 meters) from the projector. See
page 16.
The image is stretched when displaying 16:9 DVD title
When you play anamorphic DVD or 16:9 DVD, the projector will
show the best image in 16: 9 format on projector side.
If you play the LBX format DVD title, please change the format as
LBX in projector OSD.
If you play 4:3 format DVD title, please change the format as 4:3 in
projector OSD.
If the image is still stretched, you will also need to adjust the aspect
ratio by referring to the following:
Please setup the display format as 16:9 (wide) aspect ratio type
on your DVD player.
Image is too small or too large
Adjust the zoom lever on the top of the projector.
Move the projector closer to or further from the screen.
Press [ 4:3], [ 16:9], [ Letter-Box], [ Native] button
on the remote control or [Menu] on the projector panel, go to
“Display-->Format”. Try the different settings.
38
Image has slanted sides:
If possible, reposition the projector so that it is centered on the
screen and below the bottom of the screen.
Use “Display-->V.Keystone” from the OSD to make an adjust-
ment.
Image is reversed
Select “System-->Projection” from the OSD and adjust the pro-
jection direction.
Intermission Problems
The projector stops responding to all controls
If possible, turn off the projector, then unplug the power cord
and wait at least 20 seconds before reconnecting power.
Page 39
Appendices
Note
Note
Lamp burns out or makes a popping sound
When the lamp reaches its end of life, it will burn out and may
make a loud popping sound. If this happens, the projector will not
turn on until the lamp module has been replaced. To replace the
lamp, follow the procedures in the “Replacing the Lamp” section
on page 41.
Projector Status Indication
LED states
English
Steady light =>
No light =>
Message
Standby State
(Input power cord)
Power on (Warming)
Power on and Lamp
lighting
Power off (Cooling)
Error (Lamp fail)
Error (Thermal fail)
Error (Fan fail)
Error (Over Temp.)
Message Reminders
Fan failed:
Power LED
(Red)
Power LED
(Blue)
Flashing
Flashing
Temp-LED Lamp-LED
Flashing
Flashing
39
Page 40
Appendices
Over temperature:
Replacing the lamp:
Remote Control Problems
If the remote control does not work
Check the operating angle for the remote control is approximately
±22.5°.
Make sure there are not any obstructions between the remote con-
trol and the projector. Move to within 6 m (20 ft) of the projector.
Make sure batteries are inserted correctly.
Make sure batteries are exhausted. If so, replace weak batteries in
the remote control.
40
Page 41
Appendices
Replacing the lamp
The projector automatically detects the lamp life. When the lamp
life is nearing the end of use, you will receive a warning message.
English
Warning: Lamp compartment is hot! Allow
it to cool down before
changing lamp!
Warning: To reduce the
risk of personal injury,
do not drop the lamp
module or touch the
lamp bulb. The bulb
may shatter and cause
injury if it is dropped.
When you see this message, please contact your local reseller or
service center to change the lamp as soon as possible. Make sure
the projector has been cooled down for at least 30 minutes before
changing the lamp.
1
3
2
4
Lamp Replacing Procedure:
1. Switch off the power to the projector by pressing the Power
button.
2. Allow the projector to cool down at least 30 minutes.
3. Disconnect the power cord.
4. Use a screwdriver to remove the screw from the cover.
5. Push up and remove the cover.
6. Remove the 2 screws from the lamp module.
7. Pull out the lamp module.
To replace the lamp module, reverse the previous steps.
8. Turn on the projector and do “Lamp Reset” after the lamp
module is replaced.
Lamp Reset: (i)Press “Menu” -> (ii)Select “System” ->
(iii)Select “Lamp setting” ->(iv)Select “Lamp reset” ->
(v)Select “Yes”.
41
Page 42
Appendices
Note
Note
Compatibility Modes
Remark : “*”compressed computer
image.
Mode Resolution
VESA SVGA 800 x 600 60
VESA SVGA 800 x 600 72
VESA SVGA 800 x 600 75
VESA XGA 1024 x 768 60
VESA XGA 1024 x 768 70
VESA XGA 1024 x 768 75
VESA XGA 1024 x 768 85
VESA WXGA 1280 x 720 60
VESA WXGA 1280 x 768 60
VESA WXGA 1280 x 768 72
VESA WXGA 1280 x 768 85
HD 1280 x 720 60
HD 1280 x 720 72
VESA SXGA+ 1400 x 1200 60
VESA UXGA 1600 x 1200 60
* HD 1920 x 1080 24
* HD 1920 x 1080 60
* MAC 1152 x 870 75.06
MAC G4 640 x 480 60
MAC G4 1024 x 768 75
V.Frequency
(Hz)
AAnalog Digital
42
Page 43
Appendices
RS232 Commands and Protocol
Function List
RS232 Pin Assignments
3
5
1
English
9
Pin no. Name I/O (From Projector Side
1 NC __
2 RXD IN
3
4 NC __
5 GND __
6 NC __
7 NC __
8 NC __
9 NC __
TXD
6
OUT
43
Page 44
Appendices
I
n
t
e
r
f
a
c
e
:
9 wires RS-232C
B
a
u
d
R
a
t
e
:
115200
D
a
t
a
B
i
t
:
8
P
a
r
i
t
y
:
none
S
t
o
p
B
i
t
s
:
1
F
l
o
w
C
o
n
t
r
o
l
:
none
Terminatro 1
Terminator 2
S
ilence/
O
SD Mod
e
s
et/
g
et
V
i
e
w
e
d
A
s
F
u
n
c
t
i
o
n
D
e
s
c
r
i
p
t
i
o
n
A
C
K
OKOKOKOKOK
<CR><LF>-- s
Power On
Default ACK
Comand Header
Blan
k
Blan
k
A
ddress Cod
e
Command
Blan
k
Terminator 1
Header
Terminator 2
S
ilence/
O
SD Mod
e
s
et/
g
e
t
V
i
e
w
e
d
A
s
F
u
n
c
t
i
o
n
D
e
s
c
r
i
p
t
i
o
n
A
C
K
* 0 IR 002 * 0 IR <CR> -- s
Power Off
Default ACK
* 0 IR 008 * 0 IR <CR> O
s
Menu
Default ACK
* 0 IR 009 * 0 IR <CR> O
s
Up
Default ACK
* 0 IR 010 * 0 IR <CR> O
s
Down
Default ACK
* 0 IR 011 * 0 IR <CR> O
s
Right
Default ACK
* 0 IR 012 * 0 IR <CR> O
s
Left
Default ACK
* 0 IR 013 * 0 IR <CR> O
s
Enter
Default ACK
* 0 IR 014 * 0 IR <CR> -- s
Source
Default ACK
* 0 IR 015 * 0 IR <CR> -- s
Re-sync
Default ACK
* 0 IR 016 * 0 IR <CR> -- s
Source: DVI_Digital
Default ACK
* 0 IR 017 * 0 IR <CR> -- s
Source: HDMI 1
Default ACK
* 0 IR 018 * 0 IR <CR> -- s
Source: Composite Video
Default ACK
* 0 IR 019 * 0 IR <CR> -- s
Source: S-Video
Default ACK
* 0 IR 020 * 0 IR <CR> -- s
Source : DVI_Analog
Default ACK
* 0 IR 025 * 0 IR <CR> -- s
Aspect Ratio 16:9
Default ACK
* 0 IR 026 * 0 IR <CR> -- s
Aspect Ratio 4:3
Default ACK
* 0 IR 027 * 0 IR <CR> O
s
Aspect ratio LetterBox
Default ACK
* 0 IR 028 * 0 IR <CR> O
s
Aspect ratio 1:1
Default ACK
* 0 IR 030 * 0 IR <CR> S
s
Source Lock On
Default ACK
* 0 IR 031 * 0 IR <CR> S
s
Source Lock Off
Default ACK
002
008
013
014
009
031
028
030
019
C
O
M
H
B
C
O
M
010
011
012
027
025
020
H
E
A
D
B
A
D
D
R
B
T
E
R
M
2
S
I
L
N
017
026
015
S
I
L
N
018
016
D
e
f
a
u
l
t
A
C
K
:
"*000<CR" : Received OK
"*001<CR>" : Invalid Command
T
e
r
m
i
n
a
t
o
r
:
<LF> = 0Ah = "\r"
<CR> = 0Dh = "\n"
s
/
g
T
E
R
M
2
OKOKOKOKO
K
T
E
R
M
1
s
/
g
C
o
m
m
a
n
d
T
E
R
M
1
RS232 Protocol Function List
44
Page 45
Comand Header
Blan
k
Blan
k
A
ddress Cod
e
Command
Blan
k
Terminator 1
Header
Terminator 2
S
ilence/
O
SD Mod
e
s
et/
g
e
t
V
i
e
w
e
d
A
s
F
u
n
c
t
i
o
n
D
e
s
c
r
i
p
t
i
o
n
A
C
K
s
/
g
T
E
R
M
2
T
E
R
M
1
S
I
L
N
H
E
A
D
B
A
D
D
R
B
C
O
M
H
B
C
O
M
* 0 IR 035 * 0 IR <CR> -- s
Brightness
Default ACK
* 0 IR 036 * 0 IR <CR> -- s
Contrast
Default ACK
* 0 IR 037 * 0 IR <CR> -- s
Tint
Default ACK
* 0 IR 038 * 0 IR <CR> -- s
Color
Default ACK
* 0 IR 039 * 0 IR <CR> -- s
Image shift up
Default ACK
* 0 IR 040 * 0 IR <CR> -- s
Image shift down
Default ACK
* 0 IR 041 * 0 IR <CR> -- s
mode
Default ACK
* 0 IR 042 * 0 IR <CR> -- s
eage mask(overscan)
Default ACK
* 0 IR 043 * 0 IR <CR> -- s
overscan(zoom)
Default ACK
* 0 IR 046 * 0 IR <CR> O
s
Keystone shift up
Default ACK
* 0 IR 047 * 0 IR <CR> O
s
keystone shift down
Default ACK
* 0 IR 048 * 0 IR <CR> O
s
Image shift left
Default ACK
* 0 IR 049 * 0 IR <CR> O
s
Image shift right
Default ACK
* 0 IR 050 * 0 IR <CR> -- s
Source: HDMI 2
Default ACK
Comand Header
Blan
k
Blan
k
A
ddress Cod
e
Command
Blan
k
Terminator
Header
s
et/
g
e
t
V
i
e
w
e
d
A
s
F
u
n
c
t
i
o
n
D
e
s
c
r
i
p
t
i
o
n
R
e
t
u
r
n
N
o
t
e
* 0 IR 801 * 0 IR <CR> -- g
Get Lamp Hour
*002 xxxxx
Range of xxxxx is
0 <-> 99999
* 0 IR 802 * 0 IR <CR> --
g
Get Video Source *003 xx
xx means
00 : no source
01 : DVI_Digital
02 : HDMI 1
03 : Composite Video
04 : S-Video
05 : DVI_Analog
06 : Component Video
07 : HDMI 2
08 : Testin
g
* 0 IR 803 * 0 IR <CR> -- g
Get Lamp Status *004 xx
xx means
00 : Brite Mode Off
01 : Brtire Mode
* 0 IR 804 * 0 IR <CR> -- g
Get Projector status *005 xx
xx means projector is in
00 : Standby mode
01 : Power On
03: Cooling on or cooling off
04: Lamp error
05: Thermal error
050
042
040
041
036
037
038
039
035
802
803
804
043
048
049
046
047
C
O
M
H
B
C
O
M
801
H
E
A
D
B
A
D
D
R
B
s
/
g
T
E
R
M
1
Appendices
English
45
Page 46
Appendices
Min. 610.60mm
(24.04")
/ Max.
850.60mm
(33.49")
410.99mm
(16.18")
185.00mm
(7.28")
106.00mm
(4.17")
310.62mm
(12.23")
200.00mm
(7.87")
100.00mm
(3.94")
82.50mm
(3.25")
(3.25")
82.50mm
Note
Note
Ceiling Mount Installation
1. To prevent damaging your projector, please use the ceil-
2. If you wish to use a third party ceiling mount kit, please
Please note that damage resulting from
incorrect installation
will invalidate the warranty.
Warning:
1. If you buy the ceiling
mount from other
company, please
ensure that there is at
least 10cm distance
between the bottom
cover of the projector
and the ceiling.
2. Avoid placing
the projector near
sources of heat such
air-conditioning
units and heaters
otherwise it may
overheat and shut
down automatically.
3. Ceiling mounting
shall be mounting on
metal or concrete.
ing mount package for installation.
ensure the screws used to attached a mount to the projector met the following specifications:
Screw type: M4
Maximum screw length: 10mm
Minimum screw length: 8mm
46
Page 47
Appendices
Optoma Global Offices
For service or support please contact your local office.
USA
715 Sycamore Drive Tel : 408-383-3700
Milpitas, CA 95035, USA Fax: 408-383-3702
www.optomausa.com Service : services@optoma.com
Canada
5630 Kennedy Road, Mississauga,
ON, L4Z 2A9, Canada Tel : 905-361-2582
www.optoma.ca Fax: 905-361-2581
Europe
42 Caxton Way, The Watford Business Park
Watford, Hertfordshire,
WD18 8QZ, UK Tel : +44 (0) 1923 691 800
www.optoma.eu Fax: +44 (0) 1923 691 888
Service Tel : +44 (0)1923 691865 Service : service@tsc-europe.com
France
Bâtiment E Tel : +33 1 41 46 12 20
81-83 avenue Edouard Vaillant Fax: +33 1 41 46 94 35
92100 Boulogne Billancourt, France Service : savoptoma@optoma.fr
Spain
Paseo de la Castellana Tel : +34 91 790 67 01
135 7 Planta +34 91 790 67 02
Madrid, Spain Fax: + 34 91 790 68 69
Deutschland
Werftstrasse 25 Tel : +49 (0) 211 506 6670
D40549 Düsseldorf, Fax: +49 (0) 211 506 66799
Germany Service : info@optoma.de
Scandinavia
Grev Wedels Plass 2 Tel : +47 32 26 89 90
3015 Drammen Fax: +47 32 83 78 98
Norway Service : info@optoma.de
Latin America
715 Sycamore Drive Tel : 408-383-3700
Milpitas, CA 95035, USA Fax: 408-383-3702
www.optoma.com.br www.optoma.com.mx
English
47
Page 48
Appendices
Taiwan
231,台北縣新店市民權路108號5樓
R.O.C. 傳真：+886-2-2218-2313
電話：+886-2-2218-2360 www.optoma.com.tw
服務處：services@optoma.com.tw asia.optoma.com
Hong Kong
Unit A, 27/F Dragon Centre, 79 Wing Hong Street,
Cheung Sha Wan Kowloon, Hong Kong
Tel : +852-2396-8968 Fax: +852-2370-1222
www.optoma.com.hk
China
上海市长宁区凯旋路1205号5楼 电话：+86-21-62947376
邮编: 200052 传真：+86-21-62947375
www.optoma.com.cn
Japan
東京都足立区綾瀬3-25-18 サポートセンター:0120-46-5040
オーエス本社ビル
E-Mail: info@osscreen.com http://www.os-worldwide.com/
Korea
WOOMI TECH.CO.,LTD.
4F, Minu Bldg.33-14, Nonhyun-Dong, Tel : +82+2+34430004
Kangnam-Ku, seoul, 135-815, KOREA Fax: +82+2+34430005
48
Page 49
Appendices
Regulation & safety notices
This appendix lists the general notices of your Projector.
FCC notice
This device has been tested and found to comply with the limits
for a Class B digital device pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
▀■
Reorient or relocate the receiving antenna.
▀■
Increase the separation between the device and receiver.
▀■
Connect the device into an outlet on a circuit different
from that to which the receiver is connected.
▀■
Consult the dealer or an experienced radio/television
technician for help.
Notice: Shielded cables
All connections to other computing devices must be
made using shielded cables to maintain compliance with
FCC regulations.
English
Caution
Changes or modifications not expressly approved by the
manufacturer could void the user’s authority, which is
granted by the Federal Communications Commission, to
operate this computer.
49
Page 50
Appendices
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1.this device may not cause harmful interference, and
2.this device must accept any interference received, including interference that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian
ICES-003.
Remarque à l’intention des utilisateurs canadiens
Cet appareil numerique de la classe B est conforme a la norme
NMB-003 du Canada.
Declaration of Conformity for EU countries
▀■
EMC Directive 89/336/EEC (including amendments)
▀■
Low Voltage Directive 73/23/EEC (amended by 93/68/
EEC)
▀■
R & TTE Directive 1999/EC (if product has RF function)
50
Disposal instructions
Do not throw this electronic device into the
trash when discarding. To minimize pollution
and ensure utmost protection of the global
environment, please recycle it.
Loading...