SERVICE MANUAL
SI : TSE: Check: Approved:
Date Revise Version Description
2007.10.24 V1.0 Initial Issue
2008.02.15 V2.0 Add Appendix A
2008.09.24 V3.0 Add GT-7000/HD700X
HD65/GT-7000/HD700X
Copyright September, 2008. All Rights Reserved P/N: 36.89F05G001
95.89F01G00A ; 95.89F01GC0A ; 95.88N01GC0E.
HD65/GT-7000/HD700X Condential
II
Preface
This manual is applied to
HD65/GT-7000/HD700X
projection system. The manual gives
you a brief description of basic technical information to help in service and maintain the
product.
Your customers will appreciate the quick response time when you immediately identify
problems that occur with our products. We expect your customers will appreciate the
service that you offer them.
This manual is for technicians and people who have an electronic background. Please
send the product back to the distributor for repairing and do not attempt to do anything that
is complex or is not mentioned in the troubleshooting.
Notice:
The information found in this manual is subject to change without prior notice. Any
subsequent changes made to the data herein will be incorporated in future edition.
HD65/GT-7000/HD700X
Service Manual
Copyright September 2008
All Rights Reserved
Manual Version 3.0
HD65/GT-7000/HD700X
III
Condential
Part HD65 HD700X GT-7000
BOTTOM CASE 51.88N07G011 51.88N07G013
LAMP COVER 70.89F28GR01 70.89F32GR01
ELEVATOR STEP 51.88N24G011 51.88N24G001
ELEVATOR FOOT 51.88N22G011 51.88N22G001
LINKER ELEVATOR BUTTON 51.88N21G011 51.88N21G001
FIX FOOT RUBBER 52.88N06G011 52.88N06G001
ADJUSTABLE FOOT RUBBER 52.88N07G011 52.88N07G001
I/O COVER LABEL 35.89F01G001 35.89F01G011
ZOOM RING 51.88N05G011 51.88N05G001
IO COVER 51.89F01G001 51.89F01G011
MAIN BOARD 70.89F30GR01 70.89F33GR01
TOP CASE 51.88N06G061 51.88N06G0A1 51.88N06G0D1
FOCUS RING COVER 51.88N10G011 51.88N10G001
ZOOM RING COVER 51.88N12G011 51.88N12G001
KEYPAD 51.88N16G011 51.88N16G001
4 WAY KEY 51.88N17G011 51.88N17G001
ENTER KEY 51.88N18G011 51.88N18G001
LED LENS KEYPAD 51.88N19G011 51.88N19G001
CARTON AB THEMESCENE LOGO 55.89F02G001 55.89F01G001
LENS CAP 75.89F02G001 75.88N04G001
CABLE POWER CORD 42.50112G001 42.53506G001
QUICK START CARD MULTILINGUAL 36.89F03G001 36.89F03G012
INFRARED REMOTE CONTROLLER 45.89F01G001 45.89F01G002
USER’S GUIDE MULTILINGUAL 36.89F04G001 36.89F04G031
Comparison List
HD65/GT-7000/HD700X Condential
IV
Table of Content
Chapter 1 Introduction
Highlight 1-1
Compatible Mode 1-2
Chapter 2 Disassembly Process
Equipment Needed & Product Overview 2-1
Disassemble Lamp Cover 2-2
Disassemble Lamp Module 2-2
Disassemble Top Cover Module 2-3
Disassemble Keypad Board and Keypad 2-4
Disassemble IR Sensor 2-4
Disassemble I/O Cover 2-5
Disassemble Top Shielding 2-5
Disassemble Main Board Module 2-6
Disassemble Main Board Shielding 2-6
Disassemble Lamp House Shielding 2-7
Disassemble Lamp Driver Module 2-7
Disassemble Engine Module 2-8
Disassemble Color Wheel and Photo Sensor Board 2-8
Disassemble Heat Sink 2-9
Disassemble DMD Module 2-9
Disassemble Zoom Ring 2-10
Disassemble Focus Ring 2-10
Disassemble Rod Module 2-11
Disassemble Fan and Blower 2-11
Disassemble Limit Switch 2-12
HD65/GT-7000/HD700X Condential
V
Disassemble Thermal Switch 2-12
Disassemble LVPS 2-13
Disassemble Bottom Shielding 2-13
Chapter 3 Troubleshooting
LED Lighting Message 3-1
Main Procedure 3-2
Chapter 4 Function Test & Alignment Procedure
Test Equipment Needed 4-1
Service Mode 4-1
OSD Reset 4-1
Test Condition 4-2
Test Inspection Procedure 4-3
PC Mode 4-3
Video Performance 4-7
Optical Performance Measure 4-8
Other 4-9
Chapter 5 Firmware Upgrade
Equipment Needed 5-1
DLP Composer Lite Setup Procedure 5-2
USB Driver Upgrade Procedure 5-4
Firmware Upgrade Procedure 5-5
Chapter 6 EDID Upgrade
EDID Introduction 6-1
Equipment Needed 6-2
HD65/GT-7000/HD700X Condential
VI
Setup Procedure 6-3
EDID Key-In Procedure 6-3
Appendix A Exploded Image I
Appendix B SerialNumberSystemDenition XVII
PCBACodeDenition XVIII
HD65/GT-7000/HD700X Condential 1-1
Chapter 1
Introduction
1-1 Highlight
No Item Description
1 Dimension (WxHxD) - 10.2 x 2.9 x 7.4 inches (259. x 73 x 188. mm)
2 Weight - < 4.5 Lb
3 Power Supply - Universal 100—240 VAC+/-10%, 50-60 Hz with PFC input
4 Power consumption
- 265W+/-10%@110Vac(full mode)
- < 9W(Stand by)
5 Resolution - 1280x720
6 Brightness
- Typical 1300 ANSI lm
- Minimum 1100 ANSI lm
7 Contrast
- Typical: 1800:1
- Minimum: 1200:1Minimum: 1200:1
8 Uniformity
- Typical : 80%
- Minimum : 65%
9 Throw ratio - 1.55 ~1.70 (Projection Distance/Image Width)
10 Projection lens - YM09W, F/# = 2.44~2.58 at 2.36m, f = 21.8 ~ 23.8mm, 1.1X
11 Lamp life - 3000/2000 (STD Mode/Bright Mode)STD Mode/Bright Mode)/Bright Mode)
12 Tolerance - Throw ratio <= +/- 5%
13 Color wheel - 6 segments R100C23B72G90M30Y45, 3X
14 Lamp - 180W Phoenix Lamp
15 Temperature
- Operating: 5°C -- 35°C (Satised engineering specication &
functions)
- Storage: -10°C-- 60°C
16 Altitude
- Operating: 0~2,500 ft 5°C~35°C for Bright modeOperating: 0~2,500 ft 5°C~35°C for Bright mode
(5°C~40°C for STD mode)
2,500~5,000 ft 5°C~30°C
5,000~10,000 ft 5°C~25°C
- Storage :40,000 ftStorage :40,000 ft
HD65/GT-7000/HD700X
Condential
1-2
No Item Description
17 Maximum Humidity
- Operating: 5°C -- 35°C , 0 - 80 %RH (Max.), non-condensing
- Storage: -10°C -- 60°C , 0 - 80 %RH (Max.), non-condensing
18 Video compatibility
- NTSC: M (3.58MHz), 4.43 MHz, 480i/p @60Hz
PAL: B, D, G, H, I, M, N, 576i/p @50Hz
SECAM: B, D, G, K, K1, L
HDTV: 480p, 576p, 720p, 1080i(50/60 Hz),1080P(50/60 Hz)
Support SCART RGB via D-SUB (VGA)
19 Cooling System
- Advanced Air Flow
Two motor fans (one 4520 blower fan for lamp, one 6020
axial fan for system)
Temperature control circuits with adaptive voltage control fan
speed
Max touch temperature follows UL60950-1 regulation
1-2 Compatible Mode
Analog
Compatibility Resolution V-Sync [Hz]
VGA
640x350 70
640x350 85
640x400 85
640x480 60
640x480 72
640x480 75
640x480 85
720x400 70
720x400 85
SXGA
800x600 56
800x600 60
800x600 72
800x600 75
800x600 85
XGA
1024x768 60
1024x768 70
1024x768 75
1024x768 85
HD65/GT-7000/HD700X
Condential
1-3
Compatibility Resolution V-Sync [Hz]
HD 1280x720 60
SXGA
1152x864 70
1152x864 75
1152x864 85
1280x1024 60
1280x1024 75
1280x1024 85
SXGA+ 1400x1050 60
UXGA 1600x1200 60
Power Book G4-
VGA
640x480 60
640x480 72
640x480 75
640x480 85
Power Book G4-
SXGA
800x600 60
800x600 75
800x600 85
Power Book G4-
XGA
1024x768 60
1024x768 70
1024x768 75
1024x768 85
Power Book G4-
WXGA
1280x768 60
1280x768 70
Power Book G4-
HD
1280x720 60
1280x1024 60
1280x1024 75
Power Book G4-
SXGA+
1400x1050 60
Power Book G4-
UXGA
1600x1200 60
Power G4-VGA
640x480 72
640x480 75
640x480 85
Power G4-SXGA
800x600 60
800x600 75
800x600 85
Power G4-XGA
1024x768 60
1024x768 70
1024x768 75
1024x768 85
HD65/GT-7000/HD700X
Condential
1-4
Compatibility Resolution V-Sync [Hz]
Power G4-
WXGA
1280x768 60
Power G4-HD
1280x1024 60
1280x1024 75
Power G4-UXGA 1600x1200 60
iMAC-XGA 1024x768 60
Compatibility Resolution V-Sync [Hz]
VGA
640x480 60
640x480 72
640x480 75
640x480 85
720x400 70
SXGA
800x600 60
800x600 72
800x600 75
XGA
1024x768 60
1024x768 70
1024x768 75
1280x1024 60
1280x1024 75
SXGA+ 1400x1050 60
UXGA 1600x1200 60
Wide
1280x720 60
1280x720 50
1920x1080 60
1920x1080 24
1920x1080 50
Digital
HD65/GT-7000/HD700X Condential
2-1
Chapter 2
Disassembly Process
2-1 Equipment Needed & Product Overview
1. Screw Bit (+) :105
2. Screw Bit (+) :107
3. Screw Bit
(-)
:107
4. Hex Sleeves 5 mm
5. Tweezers
6. HD65/GT-7000/HD700X unit
* Before you start: This process is protective level II. Operators should wear electrostatic chains.
* Note: If you need to replace the main board, you have to get into service mode and record the
lamp usage hour.
HD65/GT-7000/HD700X Condential 2-2
2-3 Disassemble Lamp
Module
1. Unscrew 2 screws.
2-2 Disassemble Lamp
Cover
1. Unscrew 2 screws on the lamp cover
HD65/GT-7000/HD700X Condential 2-3
2-4 Disassemble Top Cover
Module
1. Press yellow square region on Top
Cover to make Zoom Ring Cover leap
from llister.
2. Unscrew 4 screws on the unit base.
Note: - When you disassemble Top Cover,you
mu s t di s a s se m bl e L am p C ov er
rst,because there is 1 screw under the
Lamp Cover.
3. Unscrew 3 screws on the besides and 3
connectors (as yellow square).
Note: - Push the top cover (as the parallel
direction),then pull it up,because there
are 8 tenons (as green square) in it.
- Avoid damage by pulling and draging
IR cable and keypad FPC cable.
- Hold the CNNT plug when pulling the
FPC cable is strongly recommended.
Pulling the cable directly from the unit
will cause the cable damages.
- Make sure cables pass through the
wire mounts (as violet square) when
assembling the unit.
HD65/GT-7000/HD700X Condential 2-4
2-5 Disassemble Keypad
Board and Keypad
1. Unscrew 3 screws to disassemble the
Keypad Board.
2. Separate the Keypads from the top cover.
Note: - Make sure cables plug into the correct
por ts wh e n ass e mbl ing t h e uni t.
2-6 Disassemble IR Sensor
1. Use tweezers to take off the black lm
tape,then press two tenons to disassemble
the IR Sensor.The other disassemble is same
as above.
HD65/GT-7000/HD700X Condential 2-5
2-7 Disassemble I/O Cover
1. Unscrew 2 hex screws and 2 screws
to disassemble I/O cover and I/O cover
Shielding.
2-8 Disassemble Top
Shielding
1. Unscrew 3 screws on the system.
Note: - When you assemble the Top
shielding,you should place the 2
edges into the gap between Main
Board and Main Board Shielding.(refer
to 2-9 and 2-10)
HD65/GT-7000/HD700X Condential 2-6
2-9 Disassemble Main Board
1. Unplug 7 connectors.
Note: - First unplug 5 connectors(as yellow
squares) and 1 connector(as red
square),then push the Main Board
as the red arrow,at last unplug the
connector (as green square).
- Make sure cables plug into the correct
ports when assembling the unit.
2-10 Disassemble Main
Board Shielding
1. Unscrew 5 hex screws on the system.
HD65/GT-7000/HD700X Condential 2-7
2-12 Disassemble Lamp
Driver Module
1. Unscrew 2 screws (as red circle) and 1
connector(as red square) to take out the
lamp driver from bottom cover.
Note: - Take care which place the cables (as
yellow dots square) pass through.
- You should make the Lamp Driver-
Main Board Cable pass through the
wire mout (as yellow square) when
you assembling the unit.
2-11 Disassemble Lamp
House Shielding
1. Unscrew 5 screws to disassemble two
House Shieldings.
Note: - When you disassemble the top House
Shieding,need to take off the white lm
tape.
HD65/GT-7000/HD700X Condential 2-8
2-13 Disassemble Lamp
Driver
1. Unscrew 2 screws to disassemble Iron
Cut.
2. Unplug 1 connector to disassemble 5 pin
cable.
3. Take off EMI Foil Copper to separate
Sheetmetal and Sheetmetal protector.
4. Unscrew 4 screws to separate Lamp
Driver and Lamp Driver Holder.
5. Take off Lamp Driver Thermal Pad.
Note: - When you paste the Thermal Pad,you
should make sure it’s edge along with
the red line.
HD65/GT-7000/HD700X Condential 2-9
2-14 Disassemble Engine
Module
1. Unscrew 4 screws on the System to
disassemble Engine Module and Wire
Mount.
2-15 Disassemble Color
Wheel and Photo
Sensor Board
1. Unscrew 2 screws (as red circle) to
disassemble Color Wheel Module.
2. Unscrew 1 screw from Color Wheel Module
(as blue circle) and take out the Photo
Sensor Board.
Wire Mount
HD65/GT-7000/HD700X Condential 2-10
2-16 Disassemble Heat Sink
1. Unscrew 4 screws on the system.
2-17 Disassemble DMD
Module
1. Unscrew 4 screws on the system then
seperate the DMD Module.
HD65/GT-7000/HD700X Condential 2-11
2-19 Disassemble Focus
Ring
1. Unscrew 3 screws (as red circle) on the
system.
2-18 Disassemble Zoom Ring
1. Unscrew 2 screws on the system.
HD65/GT-7000/HD700X Condential 2-12
2-21 Disassemble Fan and
Blower
1. Unscrew 2 screws on the bottom base,
disassemble Fan,Blower and Duct module
on the system.
2. Separate the Duct Module.
2-20 Disassemble Rod
Module
1. Unscrew 3 screws on the system.
HD65/GT-7000/HD700X Condential 2-13
2-22 Disassemble Limit
Switch
1. Unscrew 1 screw and 1connector from the
bottom base.
2.Separate Limit Switch and Limit Switch
Holder.
2-23 Disassemble Thermal
Switch
1. Unplug 1connector from the bottom
base.
Thermal Switch
HD65/GT-7000/HD700X Condential 2-14
2-25 Disassemble Bottom
Shielding
1. Unscrew 1 hex screw (as blue circle) and
1 screw(as red circle) on the bottom cover,
disassemble the Bottom Shielding.
2-24 Disassemble LVPS
Module
1. Unscrew 3 hex screws(as red circle)
2 screws(as yellow circle) and 1 screw
(as blue circle) to disassemble the LVPS
Module.
Note: - When you disassemble the Iron Cut,
you should use tweezers to raise it up,
from the hook.
- You should make the raised-dots side
of Iron Cut face to inner of the unit
when assemble it. (as red dot square).
Iron Cut
HD65/GT-7000/HD700X Condential 2-15
2-26 Disassemble Elevator
1. Unscrew 2 screws inside of the bottom
cover and 1 screw outside of the bottom
cover.
2. Separate the rest Elevator module from
the bottom cover.
Note: - Use the sweezers to take off the short
spring.
HD65/GT-7000/HD700X Condential 2-16
2-27 Rod Adjustment
1. Environment adjustment
- The distance between the engine and the
screen is 2.1M.
- This process should be done at a dark
environment. (under 5 Lux)
2. Procedure adjustment
- Change the screen to “white screen.”
- Adjust the screws by using the rod on the
engine module to readjust the image.
If there are shadow at “Top” & “Bottom”
side of the screen, adjust “Screw 1” to
adjust Rod position.
- If there are shadow / yellow light / blue
light at “Lift” &“Right” side of the screen,
adjust “Screw 2” to adjust Rod position.
- “Screw 1” should be adjusted rst, then
“Screw 2 ”.
(adjust until the yellowish or bluish parts
disappeared.)
screw 2
screw 1
HD65/GT-7000/HD700X Condential 2-17
3. Abnormal image inspection
- It should not have any abnormal color at
the rim of the image by estimating through
the eyes.
Note: - To avoid over adjust the rod.
- After the opration,please use the glue
to xed the screws.
2-28 Re-write Lamp Usage
Hours
1. Get into service mode
- Press (Power→Left→Left→Up) to get
into service mode.
2. Use “Up” or “Down” key to make light mark
stay on the “Exit”.
3. Use “Left” or “Right” key to re-write the
lamp hour back to previous lamp usage
hours.
Note: Left key = decrease lamp hour
Right key=increase lamp hour
4. Press “Enter” to exit service mode.
HD65/GT-7000/HD700X Condential
3-1
Chapter 3
Trobleshooting
3-1 LED Lighting Message
Message
Power/Standby
LED
(Green/Red)
Temp-LED
(Red)
Temp-Led
(Red)
Standby State
(input power cord)
Red
Power on
(Warming)
Flashing
Green
Lamp Lighting Green
Error
(Over Temp)
Error
(Fan Fail)
Flashing
(1sec on,1sec off)
Error
(Lamp Fail)
Note:Steady Light: No Light:
HD65/GT-7000/HD700X Condential
3-2
3-2 Main Procedure
No Symptom
Procedure
1 No Power
- Ensure the Power Cord and AC Power Outlet are securely
connected
- Check Lamp Cover and Interrupt Switch
- Ensure all connectors are securely connected and aren’t
broken
- Check Lamp Driver
- Check LVPS
- Check Main Board
2 Auto Shut Down
- Check LED Status
a. Lamp LED Light
- Check Lamp
- Check Lamp Driver
- Check Main Board
b. Temp LED Light
- Check Thermal Sensor
- Check Thermal Switch
- Check Fan
c. Color Wheel
- Check Color Wheel
- Check Photo Sensor
HD65/GT-7000/HD700X Condential
3-3
No Symptom
Procedure
3 No Image
- Ensure the Signal Cable and Source work
(If you connect multiple sources at the same time, use the
“Source” button on the control panel to swtich)
- Ensure all connectors are securely connected and aren’t
broken
- Check Main Board
- Check DMD Board
- Check Color Wheel
- Check DMD Chip
- Check Engine Module
4 No Light On
- Ensure all connectors are securely connected and aren’t
broken
- Check Lamp Module
- Check Lamp Driver
- Check LVPS
- Check Main Board
5 Machanical Noise
- Check Color Wheel
- Check Fan Module
6 Line Bar/Line Defect
- Check if the Main Board and the DMD Board are
assembled properly
- Check Main Board
- Check DMD Board
- Check DMD Chip
7 Image Flicker
- Do “Reset(All data)” of the OSD Menu
- Ensure that the signal cables and source are work as well
- Check Lamp Module
- Check Color Wheel
- Check DMD Board
- Check Main Board
HD65/GT-7000/HD700X Condential
3-4
No Symptom
Procedure
8 Color Abnormal
- Do “Reset(All data)” of the OSD Menu
- Adjust Color Wheel Index
- Check Main Board
- Check DMD Board
- Check Color Wheel
9
Poor Uniformity/
Shadow
- Ensure the projection screen without dirt
- Ensure the projection lens is clean
- Ensure the Brightness is within spec
- Check rod alignment
- Check Engine Module
10
Dead Pixel/Dust
(Out of spec.)
- Ensure the projection screen without dirt
- Ensure the projection lens is clean
- Clean DMD Chip and Engine Module
- Check DMD Chip
- Check Engine Module
11 Garbage Image
- Ensure that the signal cables and source work as well.
- Check Main Board
- Check DMD Board
12
Remote Control/
Control Panel Failed
- Remote Control
a.Check Battery
b.Check Remote Controller
c.IR receiver
d.Check Main Board
- Control Panel
a.Check FPC
b.Check keypad
c.Check Main Board
13 Function Abnormal
- Do “Reset(All data)” of the OSD Menu
- Check Main Board
- Check DMD Board
HD65/GT-7000/HD700X Condential
4-1
Chapter 4
Function Test & Alignment Procedure
4-1 Test Equipment Needed
- IBM PC with XGA/SVGA resolution
- DVD player with Multi-system (NTSC/PAL/SECAM), equipped “Component”, “S-Video” ,
“Composite” and "HDMI".
- HDTV Source (480P , 1080i , 1080P)
- Minolta CL-100
- Quantum Data 802B or CHROMA2327 (Color Video Signal & Pattern Generator)
- After changing parts, check the information below.
4-2 Service Mode
1. Turn on the projector
2. Do the following actions sequentially to enter service mode menu
(1) Press “Power”, “Left”, “Left” and “Up” button sequentially.
(2) Service mode will be shown.
(3) After conrming the conguration, press "Exit" to exit.
4-3 OSD Reset
1. After nal QC step, we have to erase all saved change again and restore the OSD
default setting. The following actions will allow you to erase all end-users' settings and
restore the default setting:
(1) Please enter OSD menu.
(2) To execute "Reset" function.
HD65/GT-7000/HD700X Condential
4-2
4-4 Test Condition
- Circumstance brightness: Dark room less than 5.0 lux.
- Inspection distance: 1.8m~2.5m functional inspection.
- Screen size: 60 inches diagonal
- After repairing each
HD65/GT-7000/HD700X
, the unit should be run-in (refer to the table
below)
Symptom Run-in Time
Normal repair 2 hours
NFF 4 hours
Auto shut down 6 hours
- Enter Burn-In Mode
* Cycle setting is based on the defect symptoms. ie: If it is NFF, the run-in time is 4 hours. You have
to set the lamp on for 50 min. and lamp off for 10 min for 4 cycles.
Press “Power”, “Left”, “Left” and “Up” button sequentially..
Choose Burn-In Test > enter
Lamp On (Min) Press right key to adjust the time (50)
Lamp Off (Min) Press right key to adjust the time (10)
Set burn in cycle Press right key to adjust the cycle
After setting up the time, choose Burn-In mode and hit enter
Screen Defects (While replacing DMD Chip, DMD BD and MB)
HD65/GT-7000/HD700X Condential
4-3
Defect specication table
Order Symptom Pattern Criteria
1 Bright pixel ( dots)
Black pattern
( IRE=O)
A+B=0
2 Dark pixel(dots) White pattern
A+B=6
3 Unstable pixel (dots) Any pattern
A+B=1
4
Adjacent dark pixel
(dots)
Any pattern
A+B=0
5 Dark blemish (Dirty) Blue 60 pattern
A+B=3
(diameter <1/2 inch)
6 Bright blemish (Dirty) Gary 30 pattern
A+B=3
(diameter <1/2 inch)
7 Bright dot on frame Black pattern 2
4-5 Test Inspection Procedure
Charge parts/
Update
M/B FW Color Wheel Lamp Module
Version Update v v
Color Wheel Index v v
PC
Calibration
YPbPr
Calibration
Reset lamp hour v
OSD Reset v v
EDID v
Re-write Lamp
Hour Usage
v
HD65/GT-7000/HD700X Condential
4-4
4-6 PC MODE
1. Frequency and tracking boundary
Procedure - Test equipment: video generator.
- Test signal: analog 1280 x 720@60Hz
- Test Pattern: general-1 or master
- Check and see if the image sharpness is well-
performed.
- If not re-adjust by the following steps:
(1) Select "Frequency" function to adjust the
total pixel number of pixel clock in one line
period.
(2) Select "Tracking" function and use right or
left arrow key to adjust the value to minimize
video icker.
- Adjust Resync or Frequency/Tracking/H. Posi-
tion/V. Position to the inner screen.
Inspection item - Eliminate visul wavy noise by Rsync, Frequency
or Tracking selction.
- Check if there is noise on the screen.
- Horizontal and vertical position of the vedio
should be adjustable to the screen frame.
Criteria - If there is noise on the screen, the product is
considered as faliure product.
- If there is noise on the screen, use auto or
manual “frequency” function or “tracking” function to adjust the screen.
- The PC mode functionally sure be workable
include support format with frequency and auto
detected functional will be workable.
General-1
Master
HD65/GT-7000/HD700X Condential
4-5
2. Light Leak
Procedure - Test equipment: video generator.
- Test signal: analog 1280 x 720@60Hz
- Test Pattern: gray 30 patterns
- Check if the light leaks.
* Light leak on reective edge, eyecatcher, bond-
wires and exposed metal.
Inspection item - Light leak check.
- Bright blemish (dirty).
Criteria - The pattern cannot accept the color level of the
leakage is brighter than the gray 30 pattern.
- Ref. below table
Note: The defect criteria follows TI specication.
3. Blemish (Dark)
Procedure - Test equipment: video generator.
- Test signal: analog 1280 x 720@60Hz.
- Test Pattern: blue 60
Inspection item - Dark blemish check.(dirty)
Criteria - The bright blemish is unacceptable when it ap-
pears on blue 60 pattern.
- Ref. below table
Note: The defect criteria follows TI specication.
4. Dead Pixel (Bright pixel)
Procedure - Test equipment: video generator.
- Test signal: analog 1280 x 720@60Hz.
- Test Pattern: full black
Inspection item - Bright pixel check.
Note: Frame dimension under operative zone1
inch
Criteria - Bright pixel is unacceptable.
- Ref. below table
Note: The defect criteria follows TI specication.
Gray 30
Blue 60
Full black
HD65/GT-7000/HD700X Condential
4-6
5. Dead Pixel (Dark pixel)
Procedure - Test equipment: video generator.
- Test signal: analog 1280 x 720@60Hz.
- Test Pattern: full white
Inspection item - Dead pixels check.
- White pattern (IRE=100)
- Adjacent dark pixel.
Criteria - The number of the dead pixels should be less or
equal to 6 pixels.
- Adjacent pixel with each other is unacceptable.
- Ref. below table
Note: The defect criteria follows TI specication.
6. Focus test
Procedure - Test equipment: video generator.
- Test signal: analog 1280 x 720@60Hz
- Test Pattern: full screen or MEME Sony
Inspection item - Focus check
Criteria - From screen 2.1 M
via visual to check the focus, look at the entire
screen, focus shall be clear, crisp, and sharp
over the entire surface of the display
pattern.(Blur word on one of the corner after
adjustment is acceptable. However, the word
should at least be recognizable.)
7. Color performance
Procedure - Test equipment: video generator.
- Test signal: DVI 1080p,1080i
- Test Pattern: Master, In focus II or SMPTE RP-
133
* Please refer to 4-2 to enter service mode. Use
1080i & 1080P signal, master pattern to do
Full white
Master
MEME Sony
Full screen
HD65/GT-7000/HD700X Condential
4-7
Motion video
HDTV test. Color cannot discolor to purple and
blue. If the test result is discoloration or ickering, please return the unit back to repair
centers.
Inspection item - Check if each color level is well-functioned.
- color saturations
Criteria - Screen appears normal. It should not have any
abnormal condition, such as lines appear on the
screen and so on.
- Color appears normal.
- It is acceptable to have few lines ashing at the
center and on the edge of 1080P image. However, rest of the image should appears stable.
- RGBW should all appear normal on the screen
and sort from R -G-B-W.
- Color levels should be sufcient and normal.
(the unidentied color levels on both left and
right sides should not over 8 color levels.)
- Gray level should not have abnormal color or
heavy lines.
- The PC mode functionally sure be workable
include support format with frequency and auto
detected functional will be workable
4-7 Video Performance
1. CVBS
Procedure - Test equipment: DVD player
- Test signal: CVBS
Inspection item - Video performance test
Inspection Distance - 1.8M ~2.5M
Criteria - Check any abnormal color, line distortion or anyabnormal color, line distortion or any color, line distortion or any
noise on the screen.
- Check the sound from speakers.
SMPTE RP-133
InFocus II
/ 64 gray RGBW
HD65/GT-7000/HD700X Condential
4-8
2. S-Video
Procedure - Test equipment: DVD player
- Test signal: S-Video
Inspection item - Video performance test
Inspection Distance - 1.8M ~2.5M
Criteria - Check any abnormal color, line distortion or any
noise on the screen.
- Check the sound from speakers.
3. HDTV/ Component
Procedure - Test equipment: DVD player
- Test signal: Ycbcr/YPbPr
Inspection item - HDTV performance test
Inspection Distance - 1.8M ~2.5M
Criteria - Check any abnormal color, line distortion or anyabnormal color, line distortion or any color, line distortion or any
noise on the screen.
- Check the sound from speakers.
4. Audio Test
Procedure - Test equipment: DVD player
- Test signal: CVBS
Inspection item - Audio performance test
Inspection Distance - 1.8M ~2.5M
Criteria - Check the sound from speakers.
- Check “Volume” is normal
- Check “Mute” is normal
HD65/GT-7000/HD700X Condential
4-9
4-8 Optical Performance Measure
Inspection Condition
- Environment luminance: 5 Lux
- Product must be warmed up for 3 minutes
- Distances from the screen: 2.1 M
- Screen Size: 60 inches diagonal
- Reset to default before measurement
1. Test equipment
Procedure - Test equipment: video generator.
- Test signal: analog 1280 x 720@60Hz
2. Brightness
Procedure - Full white pattern
- Use CL100 to measure brightness values of
P1~P9.
- Follow the brightness formula to calculate
brightness values.
☼ Brightness Formula
Avg.(P1~ P9)x1.1m2
Criteria - 605 lumens
3. Ful On/Full Off Contrast
Procedure - Full white pattern & full black pattern
- Use CL100 to measure brightness values of full
white pattern P5 & full black pattern B5 ( see image: full white)
- Follow Contrast formula to calculate contrast
values.
☼ Contrast Formula
P5/B5
Full white pattern
Full black pattern
HD65/GT-7000/HD700X Condential
4-10
x 100%
note: P5=center of white image
B5=center of black image.
Criteria - 1200:1
4. Uniformity
Procedure - Full white pattern
- Use CL100 to measure brightness values of
P1~P9 (see image: full white).
- Follow the Uniformity formula to calculate
average values.
☼ Uniformity Formula
ANSI Uniformity = Avg. (P1, P3, P7, P9)
P5
Criteria - 65% (JBMA)
4-9 Others
1. Functional Inspection
Keypad button - All keypad buttons must operate
smoothly.
General - All OSD functions must be
checked for functionality. When
OSD menu is displayed, there
shall be no visible peaking,
ringing, streaking, or smearing
artifacts on the screen.
Factory Default - The factory settings (with appro-
priate centering, size, geometry
distortion, etc.) shall be displayed
upon “Recall” is selected from
OSD
HD65/GT-7000/HD700X Condential
4-11
Display Size - All preset modes shall expand to
full screen size using OSD Horizontal and Vertical Size controls
Display Data Channel (DDC) - The purpose of the DDC test is to
verify the DDC1/DDC2B operation
of the projector and to verify Plug &
Play function.
Acoustic - High pitch sound from cooling fan
and color wheel is unacceptable.
2. Check points for exterior and print pattern
Check item Check point
Text & Pattern
Mi s s i n g letters & pattern or blurry prints a re
unacceptable.
Exterior
Dirt, scrape, water ripples and uneven color are
unacceptable.
Buttons Stuck buttons are unacceptable.
Focus ring Focus ring is functioning smoothly.
Logo
Missing logo, missing prints and blurry prints are
unacceptable
Screw
All screw sure be xed and in right type.
Pedestal Well-functioned
Lamp Cover It should be locked in the correct place.
Plastic Parts All plastic parts can not be brocken and damaged.
Safety or warning
label
All safety and warning label should be visible,
including all contents.
Connector
All interface connector should be complete and
workable.
HD65/GT-7000/HD700X
Condential 5-1
Chapter 5
Firmware Upgrade
5-1 Equipment Needed
Software : (DDP 2230- USB)
- DLP Composer
- Firmware
- Library le (library le has to put in PC and set right path in 5-4 step 4)
Hardware :
- Projector
- Power cord:42.50115G001
- USB Cable:42.00280G001
- PC or Laptop
HD65/GT-7000/HD700X Condential
5-2
5-2 DLP Composer Lite Setup
Procedure
1. Choose “DLP Composer Lite V7.1 Setup”
Program.
2. Click “Next” buttom
3. Read “License Agreement.”
- Choose “I accept and agree to be bound
by all the terms and conditions of this
License Agreement.”
- Click "Next" button.
4. Click “Next” button.
HD65/GT-7000/HD700X Condential
5-3
5. Click “Next” button.
6. Click “Next” button.
7. The program is executing"Initializing"status
8. Click “Finish.”
HD65/GT-7000/HD700X Condential
5-4
5-3 USB Driver Upgrade Procedure
1. Set up
- Connect the Projector with PC by USB cable.
- It will show as the right picture.
- Select the item as red circle show.
- Click "Next" button.
2. Installation
- Cilck “Finish“ and then the USB driver
has been set up successfully.
HD65/GT-7000/HD700X Condential
5-5
5-4 Firmware Upgrade Procedre
1.
Set-up
- Hold on “Menu” button then plug in power cord.
- Once lamp and temp LED light up, plug in USB
cable into the projector and link to the USB port of
PC.
Note: The system fan and the light will not operated.
2. Execute the “DLP Compose
TM”
le.
.
3. Click “edit” and “perferences.”
4. Click “Library.”
- The library path located in the default installation
directory
- E:\Program FIles\DLP Composer Lite 7.1\library
v7.1 0330
Note: If not, press “Browse” to select the right path.
HD65/GT-7000/HD700X Condential
5-6
5. Select “Edit\preferences\Communications”
- Choose “USB.” Click “OK.”
6.
Choose “Flash Loader.”
- Click “Browse” to search the rmware le.
- Skip Boot Loader Area choose"32KB"
7. Click “Reset Bus” to erase the ash
memory
Note: If the error message“cannot open USB
driver - No projectors found” appears,
please unplug the USB Cable and replug,
then check Driver. Finally,repeat procedure
7.Click“ResetBus”toerasetheash
memory.
8. If the rmware is ready, click “start
download” to process the rmware
upgrade.
- Click “Yes” to erase the ash memory.
1
HD65/GT-7000/HD700X Condential
5-7
9. Proceeding Picture.
10. When rmware upgrade process is
nished, the unit return to stand-by status.
The LED power lights on and appears blue.
- Unplug USB cable and power cord and
replug in power cable.
11. Restart the unit and enter the Service mode
to check the rmware version.
(To enter
Service
mode, please refer to Chapter
4 Function Test and Alignment Procedure.)
1
HD65/GT-7000/HD700X Condential
6-1
Chapter 6
EDID Upgrade
6-1 EDID Introduction
Extended Display Identication Data is a VESA standard data format that contains basic
information about a display device and its capabilities, including vendor information,
maximum image size, color characteristics, factory pre-set timings, frequency range limits,
and character strings for the monitor name and serial number.
The information is stored in the display and is used to communicate with the system
through a Display Data Channel (DDC), which sites between the display device and the
PC graphics adapter. The system uses this information for conguration purposes, so the
monitor and system can work together.
Note: If a display device has digital input ports, like DVI or HDMI, but without EDID in its
main board, the display device will show no image while the input source is digital signal.
HD65/GT-7000/HD700X Condential
6-2
6-2 Equipment Needed
Software
- EDID Program (Generic V0.51)
- EDID File *.ini
Hardware
- Projector
- Generic Fixture :80.00001.001 for EDID Key-in (Fixture: JP3 must be closed)
- Power cord
- RS-232 Cable (pin to pin, F-M):42.83618G001
- Monitor
- PC
- VGA cable:42.87305G001
- Power adapter for xture :47.57702G001
- DVI adapter for HDMI :42.82B13G001
- DVI Cable: 42.83N06G001
HD65/GT-7000/HD700X Condential
6-3
6-4 EDID Key-In Procedure
1. Click on "EDID" to execute EDID program
2. Choose model
- In the port selection bar, please choose
the port that you use. Example: if you
use "COM1," choose COM1 in the port
selection.
- Click on "Model."
- Choose the EDID that responses to the
model that you choose.
6-3 Setup Procedure
1. Connect all ports
- Power adapter to xture JP1
- Fixture P1 to PC COM1 Port
- Fixture P4 to Projector analog port
- Fixture P3 to Projector digital port
- Power on xture
VGA Cable
RS232 Cable
JP1
P4
P1
Adapter
P3
DVI Cable
HD65/GT-7000/HD700X Condential
6-4
3. Programming
- Key in the serial number into the
barcode blank space.
- In "Write Source Select," make a check
in “Analog”and “Digital”.
- Click "Program."
4. Change the cable to VGA
- Message box appears on the screen,
then click "OK."
5. Change the cable to HDMI
- Message box appears on the screen,
plug DVI Cable to connect to adapter
then plug in HDMI port. After nish above
action, click "OK."
6. When the EDID program is completed,
a message "OK" will appear on the screen.
HD65/GT-7000/HD700X Condential
6-5
7. Read EDID “Analog” information
- In the Read item,select “Analog”and “Trans”,
then click the “Read” button.
8. Read EDID “Digital” information
- If EDID’s information is correct,select
“Digital” and“Trans” in the Read item,then click
the "Read" button.
9. EDID informations will show the result.
HD65/GT-7000/HD700X Condential
I
Appendix A
Assy Bottom-case Module HD65
[10]
[20]
[13]
[22]
[21]
[5]
[23]
[4]
[3]
[17]
[18]
[6]
[9]
[8]
[7]
[14]
[15]
[16]
[1]
[2]
[11]
[12]
[19]
[25]
[24]
HD65/GT-7000/HD700X Condential
II
item P/N Rev Description Parts Supply
1 51.88N07G011 A BOTTOM CASE PC CM7326A(GRAY) HD65
2 75.88N01G001 A ASSY HITACHI LAMPDRIVER 180W
3 75.88N02G001 A ASSY INTERLOCK SWITCH MODULE
4 70.89F13G001 A ASSY LVPS SHEETMETAL MODULE HD65 NO
5 70.89F14G001 A ASSY BLOWER MODULE HD65 NO
6 70.89F09G001 A ASSY ELEVATOR MODULE HD65 NO
7 51.88N22G011 A
ELEVATOR FOOT PC
MN3600HC(GRAY)HD65
8 51.88N21G011 A
LINKER ELEVATOR BUTTON PC
MN3600HC(GRAY)HD65
9 61.82Y22G001 A
ELEVATOR PUSH SPRING SUS304 D=φ4.4
d=φ0.4 L=10 DP715
NO
10 61.88N28G001 A MAIN BOARD STAND-OFF M2.6X39.7mm NO
11 85.1C224G051 A
SCREW PAN MECH M4*5 COLOR W/TOOTH
WASHER Cr3+
NO
12 61.88N29G001 A MAIN BOARD STAND-OFF M2.6X4.0mm NO
13 85.1A526G060 A SCREW PAN MECH M2.6*6 Ni NYLOK NO
14 52.88N06G011 A FIX FOOT RUBBER HD65
15 52.88N07G011 A ADJUSTABLE FOOT RUBBER HD65
16 86.0A123G024 A HEX NUT M3*0.5P L2.4 Ni NO
17 49.88N01G001 A SUNON 60X20 AXIAL FAN
18 75.87J01G101 A
ASSY LVPS MATRITEK 200W
EP752(CHINA’S PROCESS)
19 52.88N13G001 A SPONGE FOR BLOWER BOTTOM NO
20 85.3A126G040 A SCREW CAP HEAD D7.0 MECH M2.6*4 Ni NO
21 61.88N20G001 A
SHEET METAL TOP CASE ISOLATION
SECC,EP721
NO
22 43.88N01G001 A
THERMAL SWITCH WITH BRACKET (KLIXON YS11) 100 DEG. C
23 49.88N02G002 A SUNON 45X20 BLOWER
24 52.88N14G001 A SPONGE FOR BLOWER TOP NO
25 41.83Y09G001 A EMI TAPE W20xL15mm , FF1 NO
HD65/GT-7000/HD700X Condential III
Assy Top-case HD65
EXPLODED.STATE
[1]
[2]
[3]
[5]
[4]
[6]
[7]
[8]
[9]
[10]
[11]
[11]
[13]
[14]
[15]
[16]
[17]
[18]
[21]
[12]
[20]
[19]
HD65/GT-7000/HD700X Condential IV
item P/N Rev Description Parts Supply
1 51.88N06G011 A TOP CASE PC CM7326A(GRAY) HD65
2 51.88N13G001 A TOP IR LENS PC,EP721
3 51.88N16G011 A KEYPAD PC MN3600HC(GRAY)HD65
4 51.88N17G011 A 4 WAY KEY PC MN3600HC(GRAY)HD65
5 51.88N18G011 A ENTER KEY PC MN3600HC(GRAY)HD65
6 51.88N19G011 A LED LENS KEYPAD,PC,EP721
7 51.88N26G001 A FRONT IR LENS PC,EP721
8 85.1A526G060 A SCREW PAN MECH M2.6*6 Ni NYLOK NO
9 41.85E03G001 A EMI GASKET W10*L25*H7mm NO
10 80.89F03G001 B PCBA KEYPAD BOARD FOR HD65
11 80.89F04G001 A PCBA PHOTO SENSOR BOARD FOR HD65
12 51.88N28G001 A MYLAY FOR TOP IR LENS PP EP721 NO
13 51.88N30G002 A ADHESIVE1 FOR TOP IR LENS,EP721
14 51.88N31G002 A ADHESIVE2 FOR TOP IR LENS,EP721
15 51.88N32G001 A ADHESIVE FOR LED LENS EP721
16 52.88N15G001 A SPONGE1 FOR TOP CASE EP721 NO
17 52.88N16G001 A SPONGE2 FOR TOP CASE EP721 NO
18 52.88N17G001 A SPONGE3 FOR TOP CASE EP721 NO
19 42.0030EG150 A
FFC 20P P=0.5mm MAIN BOARD TO KEYPAD
BOARD 150mm EP721
20 51.82Y27G001 A
TAPE 3M J1350 45*45mm FOR MIRROR 2
DP715
NO
21 41.82G05G001 A EMI GASKET W10*L20*H3mm EP719 NO
HD65/GT-7000/HD700X Condential V
Assy Optical Engine HD65
ASSY.STATE
[1]
[2]
[3]
[4]
[5]
[7]
[6]
[8]
[9]
[17]
[23]
[10]
[12]
[13]
[24]
[14]
[15]
[16]
[18]
[19]
[21]
[25]
[29]
[26]
[28]
[20]
[27]
[22]
HD65/GT-7000/HD700X Condential VI
item P/N Rev Description Parts Supply
70.89F25GR01 A ASSY ENGINE MODULE HD65(SERVICE)
1 70.89F15G001 A ASSY ENGINE BOTTOM COVER HD65 NO
2 51.88N05G011 A ZOOM RING PC MN3600HC HD65
3 70.89F05G001 A ASSY ROD MODULE HD65 NO
4 70.89F06G001 A ASSY COLOR WHEEL MODULE HD65 NO
5 61.89F04G001 A DMD HEATSINK AL HD65 NO
6 61.82B36G001 A SCREW M3*10 IHSPC NO
7 61.82B37G001 A HEAT SINK SPRING NO
8 61.88611G001 A DMD SCREW Ivy10X NO
9 51.00210G001 A DMD SCREW WASHER A39 NO
10 80.89F02G001 A PCBA DMD BD FOR HD65
11 41.82G10G001 A EMI GASKET W10*L45*H13mm EP719 NO
12 61.80J10G001 E DMD LIGHT MASK 739 SUS301 NO
13 70.89F04G001 A PRE ASSY ENGINE BASE HD65 NO
14 23.88N20G001 A YO CONDENSER1 FOR X15 NO
15 23.88N20G011 A YO CONDENSER2 FOR X15 NO
16 23.88N06G001 A YO PLASTIC RELAY FOR X15 NO
17 61.89F01G001 A DMD PLATE AL A6061 HD65 NO
18 61.89F02G001 A ROD COVER SUS304 0.25t 1/2H HD65 NO
19 61.88N12G001 A ROD SPRING SUS301,X15 NO
20 41.81U03G001 A EMI TAPE W40*L80mm NO
21 51.88N03G011 A ZOOM RING HOLDER PC MN3600HC HD65 NO
22 52.87319G001 DMD THERMAL PAD 18*13*0.5t
23 51.89F02G001 A DMD INSULATION PC A15 NO
24 52.80J01G001 B
DMD ANTIDUST RUBBER 73 9 SILICONE
RUBBER
NO
25 48.86N01G003 A
DMD 128 0x72 0 P IXEL 0.62 ” 7 20P LVDS
HORIZONTAL LINE FIX “TI”
26 23.89L01G001 A PROJECTION LENS YM09W NO
27 85.1A121G040 A SCREW PAN MECH MI,7*4 Ni NO
28 51.89F03G001 A FOCUS RING PC MN3600HC HD65 NO
29 11.009F0G007 A
CNNT F 203P FOR 720P LGA DMD SOCKET
PE020323-03040-10;FOXCO
HD65/GT-7000/HD700X Condential VII
Assy ROD Module HD65
item P/N Rev Description Parts Supply
70.89F05G001 A ASSY ROD MODULE HD65
1 23.89F17G001 A YO STEP ROD FOR A15 720P X15 NO
2 61.89F03G001 A ROD HOLDER SUS301 0.25t 1/2H HD65 NO
[1]
[2]
HD65/GT-7000/HD700X Condential VIII
item P/N Rev Description Parts Supply
70.89F24GR01
A
A S S Y C O L O R W H E E L M O D U L E
HD65(SERVICE)
1 23.89F19G001 A
YO 6 SEGMENT CW R100C23B72G90M30Y45
FOR HD65
NO
2 61.88N10G001 A COLOR WHEEL HOLDER SECC,X15 NO
3 52.83615G001 A COLOR WHEEL DISC RUBBER, EzPro755 NO
4 61.83628G001 A COLOR WHEEL SHOULDER SCREW,EzPro755 NO
5 85.1A126G040 A SCREW PAN MECH M2.6*4 Ni NO
6 80.89F04G001 A PCBA PHOTO SENSOR BOARD FOR HD
Assy Color Wheel HD65
[4]
[1]
[2]
[3]
[6]
[5]
HD65/GT-7000/HD700X Condential IX
Assy Lamp HD65
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[14]
[11]
[12]
[13]
[15]
HD65/GT-7000/HD700X X
Condential
item P/N Rev Description Parts Supply
1 51.88N02G001 A LAMP HOUSING PPS,X15 NO
2 61.88N02G001 A LAMP HOLDER MG,X15 NO
3 61.88N06G001 B LAMP MESH LEFT SUS301,X15 NO
4 61.88N07G001 A LAMP MESH,RIGHT,SUS301,X15 NO
5 61.88N09G001 A UV IR HOLDER SUS301,X15 NO
6 61.88N25G001 A 88N LEAKAGE HOLDER,AL,X15 NO
7 61.88N08G002 A LAMP FIX SPRING-NEW SUS301 X15 NO
8 61.88N04G001 A LAMP SHELL,AL5052,X15 NO
9 52.88N08G001 A 88N LAMP SHELL RUBBER,X15 NO
10 23.88K15G001 A LAMP MODULE PHOENIX 180W FEX88 NO
11 23.87M10G002 A UV-IR-IR 24*25*2 mm(5*5 mm cut)-YO NO
12 61.86808G001 A
LAMP C HANGER HAND LE SU S304 1.6d
DP725
NO
13 61.85928G001 A LAMP HOUSING SHOULDER SCREW SB21 NO
14 85.1A526G060 A SCREW PAN MECH M2.6*6 Ni NYLOKSS NO
15 35.88N03G002 A LAMP WARNING LABEL NEW EP721
HD65/GT-7000/HD700X Condential XI
D.C. HD65
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[16]
[11]
[14]
[15]
[10]
[12]
[13]
[17]
HD65/GT-7000/HD700X Condential XII
item P/N Rev Description Parts Supply
1 70.89F01G001 A ASSY BOTTOM CASE MODULE HD65 NO
2 70.89F02G001 A ASSY TOP CASE MODULE HD65 NO
3 70.89F03G001 A ASSY ENGINE MODULE HD65 NO
4 70.89F16G001 A ASSY LAMP MODULE HD65 NO
5 51.89F01G001 A IO COVER PC MN-3600H HD65
6 61.89F06G001 A SHEET MEATL IO SUS301 HD65 NO
7 80.89F01G001 A PCBA MAIN BD FOR HD65
8 61.89F07G001 A SHEET METAL BTM M/B SECC HD65 NO
9 61.89F08G001 A SHEET METAL IO COVER HOLD SECC HD65 NO
10 85.1A126G040 A SCREW PAN MECH M2.6*4 Ni NO
11 85.1A526G060 A SCREW PAN MECH M2.6*6 Ni NYLOK NO
12
85.005AGG040 A
SCR EW I/O S H EEL #4- 40U NC* H4* L5. 5
NYLOK
NO
13 85.1A122G040 A SCREW PAN MECH M2*4 Ni NO
14 51.88N10G011 A
FO C U S RI N G CO V E R PC MN 3 6 0 0 H C
(GARY) HD65
15 51.88N12G011 A
ZOOM RING COVER PC MN3600HC(GARY)
HD65
16 70.89F10G001 A ASSY LAMP COVER MODULE HD65 NO
17 35.89F01G001 A I/O COVER LABEL HD65
HD65/GT-7000/HD700X Condential XIII
D.P. HD65
HD65/GT-7000/HD700X Condential XIV
item P/N Rev Description Parts Supply
1 DC.89F01G001 A D.C. HD65 NO
2 42.50115G001 A CABLE POWER CORD 1.8M SP30+IS14 US
3 51.86213G002 A
PE BAG ZIPPER #9 W/RECYCLING MARK
FOR OPTOMA
4 36.00020G001 A
Q U I C K TR O U B L E S H O O T I N G GU I D E
MULTILINGUAL
5 36.00018G001 B
EXTENDED WARRANTY REGISTRATION
FORM,USA FOR LPP SERIES
6 36.80A01G001 A
S A F E T Y & W A R R A N T Y G U I D E ,
MULTILINGUAL H30 GREEN
7 36.89F03G001 B
QU I C K STA RT CA RD MU LT I L IN G U AL
OPTOMA HD65
8 36.89F01G001 A
USER’S MANUAL FOR USA/ASIA, OPTOMA
HD65
9 45.89F01G001 A
INFRARED REMOTE CONTROLLER HD65
(Parex)
10 42.80708G002 A CABLE RCA PLUG #27 2M 2M PD726/PH730
11 42.87205G201 A
C A B L E C O M P O S I T E V I D E O 1 . 8 M
EP729;SUZHOU
12 75.89F02G001 A ASSY LENS CAP MODULE HD65
13 55.89F01G001 A CARTON AB OPTOMA LOGO HD65
14 56.89F01G001 A CUSHION-L EPE HD65
15 56.89F02G001 A CUSHION-R EPE HD65
16 55.89F03G001 A PAPER SUPPORT BOX HD65
17 51.00200G001 A HANDLE BAR 2. PE HD70
18 51.00201G001 A HANDLE BAR 1.PE HD70
20 51.52109G003 A PE BAG 450*350*0.07 FOR OPTOMA
24 35.88N02G001 A SPEC LABEL EP721
25 35.52302G091 A LABEL CARTON 108*92 BLANK
HD65/GT-7000/HD700X Condential XV
Appendix B
I. Serial Number System Denition
Serial Number Format for Projector (For HD65)
Q 89F 7 33 AAAAA C 0001
1 2 3 4 5 6 7
1 : Q = Optoma
2 : 89F = Project code
3 : 7 = Last number of the year (ex:2007 = 7)
4 : 33 = week of the year ( ex:the thirty-three week of the year = 33)
5 : AAAAA = not-dened
6 : C = Manufacture factory (TW or CPC)
7 : 0001 = Serial code
EX: Q89F733AAAAAC0001
This label represents the serial number for HD65. It is produced for USA at CPC on Thirtythree week of 2007. Its serial code is 0001.
HD65/GT-7000/HD700X Condential XVI
Serial Number Format for Projector (For HD700X)
Q 89F 7 48 AAASS C 0001
1 2 3 4 5 6 7
1 : Q = Optoma
2 : 89F = Project code
3 : 7 = Last number of the year (ex:2007 = 7)
4 : 48 = week of the year ( ex:the forty-eight week of the year = 48)
5 : AAASS = not-dened .SS=HD700X
6 : C = Manufacture factory (TW or CPC)
7 : 0001 = Serial code
EX: Q89F748AAASSC0001
This label represents the serial number for HD700X. It is produced for USA at CPC on
Forty-eight week of 2007. Its serial code is 0001.
HD65/GT-7000/HD700X Condential XVII
Serial Number Format for Projector (For GT-7000)
Q 89F 8 20 AAASS C 0001
1 2 3 4 5 6 7
1 : Q = Optoma
2 : 89F = Project code
3 : 8 = Last number of the year (ex:2008 = 8)
4 : 20 = week of the year ( ex:the Twenty week of the year = 20)
5 : AAASS = not-dened .SS=GT-7000
6 : C = Manufacture factory (TW or CPC)
7 : 0001 = Serial code
EX: Q89F820AAASSC0001
This label represents the serial number for GT-7000. It is produced for USA at CPC on
Twenty week of 2008. Its serial code is 0001.
HD65/GT-7000/HD700X Condential XVIII
II. PCBA Code Denition
PCBA Code for Projector
A B XXXXXXXXXX C XXX EEEE
1 2 3 4 5 6
1 : ID
2 : Vendor Code
3 : P/N
4 : Revision
5 : Date Code
6 : S/N
Loading...