Optoma DS339, DW339, DX339, TW556 3D User Guide

1

English

Table of Contents

Table of Contents ............................1

Usage Notice ...................................2

Safety Information ...............................2

Precautions .........................................3

Eye Safety Warnings ..........................5

Product Features ................................5

Introduction ......................................6

Package Overview ..............................6

Product Overview ...............................7

Main Unit ..............................................7

Control Panel ....................................... 8

Input/Output Connections .................... 9

Remote Control ..................................10

Installation ..................................... 11

Connecting the Projector .................. 11

Connect to Computer/Notebook ........ 11

Connect to Video Sources ................. 12

Powering the projector On / Off ........13

Powering On the Projector .................13

Powering Off the Projector .................14

Warning Indicator ...............................14

Adjusting the Projected Image ..........15

Adjusting the Projector’s Height ........ 15

Adjusting the Projector’s Zoom /

Focus ................................................. 16

Adjusting Projection Image Size ........ 16

User Controls ................................18

Control Panel & Remote Control ......18

Control Panel ..................................... 18

Remote Control ..................................19

On-screen Display Menus ................24

How to operate .................................24

Menu Tree .......................................... 25

IMAGE ............................................... 27

IMAGE | Advanced ............................ 29

DISPLAY ............................................ 31

DISPLAY | 3D ................................... 34

SETUP ............................................... 35

SETUP | Signal (RGB) ....................... 37

SETUP | Security ............................... 38

SETUP | Advanced ............................ 40

OPTIONS ........................................... 41

OPTIONS | Advanced ........................ 42

OPTIONS | Lamp Settings ................. 43

Appendices ....................................44

Troubleshooting ................................44

Replacing the lamp ...........................49

Compatibility Modes .........................51

Computer Compatibility .....................51

Video Compatibility ............................ 53

RS232 Commands and Protocol

Function List .....................................54

RS232 Pin Assignments .................... 54

RS232 Protocol Function List ............ 55

Wall Mount Installation ......................59

Optoma Global Ofces .....................60

Regulation & Safety Notices .............62

2

English

Usage Notice

Safety Information

The lightning ash with arrow head within an equilateral triangle is

intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may be of sufcient
magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH
VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE
CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

Class B emissions limits

This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.

Important Safety Instruction

1. Do not block any ventilation openings. To ensure reliable operation of
the projector and to protect from over heating, it is recommended to
install the projector in a location that does not block ventilation. As an
example, do not place the projector on a crowded coffee table, sofa,
bed, etc. Do not put the projector in an enclosure such as a book case
or a cabinet that restricts air ow.

2. Do not use the projector near water or moisture. To reduce the risk
of re and/or electric shock, do not expose the projector to rain or
moisture.

3. Do not install near heat sources such as radiators, heaters, stoves or

any other apparatus such as ampliers that emits heat.

4. Clean only with dry cloth.

5. Only use attachments/accessories specied by the manufacturer.

6. Do not use the unit if it has been physically damaged or abused.
Physical damage/abuse would be (but not limited to):

 Unit has been dropped.
 Power supply cord or plug has been damaged.
 Liquid has been spilled on to the projector.
 Projector has been exposed to rain or moisture.
 Something has fallen in the projector or something is loose inside.

Do not attempt to service the unit yourself. Opening or removing covers
may expose you to dangerous voltages or other hazards. Please call
Optoma before you send the unit for repair.

7. Do not let objects or liquids enter the projector. They may touch
dangerous voltage points and short out parts that could result in re or
electric shock.

8. See projector enclosure for safety related markings.

9. The unit should only be repaired by appropriate service personnel.

3

English

Usage Notice

Precautions

Please follow all warnings, precautions and
maintenance as recommended in this user’s
guide.

▀■ Warning- Do not look into the projector’s lens when the lamp is

on. The bright light may hurt and damage your eyes.

▀■ Warning- To reduce the risk of re or electric shock, do not

expose this projector to rain or moisture.

▀■ Warning- Please do not open or disassemble the projector as

this may cause electric shock.

▀■ Warning- When replacing the lamp, please allow the unit to

cool down. Follow instructions as described on pages

49-50.

▀■ Warning- This projector will detect the life of the lamp itself.

Please be sure to change the lamp when it shows
warning messages.

▀■ Warning- Reset the “Lamp Reset” function from the on-screen

display “OPTIONS | Lamp Settings” menu after
replacing the lamp module (refer to page 43).

When the lamp

reaches the end
of its life, the pro-

jector will not turn
back on until the
lamp module has

been replaced.
To replace the

lamp, follow the

procedures listed
under “Replacing

the Lamp” section

on pages 49-50.

▀■ Warning- When switching the projector off, please ensure

the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the
projector to cool down.

▀■ Warning- Do not use lens cap when projector is in operation.

▀■ Warning- When the lamp is approaching the end of its lifetime,

the message “Lamp Warning: Lamp life exceeded.”
will show on the screen. Please contact your local
reseller or service center to change the lamp as soon

as possible.

▀■ Warning- Do not look into or point the laser pointer on your

remote control into your or someone’s eyes. Laser
pointer can cause permanent damage to eyesight.

4

English

Usage Notice

Do:

  Turn off and unplug the power plug from the AC outlet before

cleaning the product.

  Use a soft dry cloth with mild detergent to clean the display

housing.

  Disconnect the power plug from AC outlet if the product is

not being used for a long period of time.

Do not:

  Block the slots and openings on the unit provided for

ventilation.

 Use abrasive cleaners, waxes or solvents to clean the unit.

 Use under the following conditions:

- In extremely hot, cold or humid environments.

Ensure that the ambient room temperature is within



5 - 40°C.

Relative Humidity is 5 - 40°C, 80% (Max.),



non-condensing.

- In areas susceptible to excessive dust and dirt.

- Near any appliance generating a strong magnetic eld.

- In direct sunlight.

5

English

Usage Notice

Eye Safety Warnings

▀■ Avoid staring/facing directly into the projector beam at all

times. Keep your back to the beam as much as possible.

▀■ When projector is used in a classroom, adequately supervise

students when they are asked to point out something on the

screen.

▀■ In order to minimize the lamp power, use room blinds to

reduce ambient light levels.

Product Features

Monitor loop

through only sup­port in VGA1-In/

YPbPr.

▀■ SVGA (800x600) Native resolution /

XGA (1024x768) Native resolution /

WXGA (1280x800) Native resolution

▀■ HD compatible – 720p and 1080p supported

▀■ VGA monitor loop through

(works on standby mode > 1W)

▀■ BrilliantColorTM Technology

▀■ Security Bar and Kensington Lock

▀■ RS232 control

▀■ Rapid shutdown
▀■ Built-in speakers
▀■ Quick Resume and Eco+ mode

6

English

Introduction

Package Overview

Unpack and inspect the box contents to ensure
all parts listed below are in the box. If something
is missing, please contact your nearest customer
service center.

Due to different

applications in

each country,
some regions
may have

different
accessories.

Projector

2 × AAA Batteries

Documentation :

User’s Manual



Warranty Card



Quick Start Card



WEEE Card



(for EMEA only)

STOP Card



(for US Only)

Power Cord

IR Remote Control

VGA Cable

7

English

Introduction

Product Overview

Main Unit

The interface

is subject to
model’s speci­cations.

10

11

56

7

8

9

14

10

3

2

1. Control Panel

2. Focus Ring

3. Speaker

4. Zoom Ring

5. Lens

6. IR Receiver

7. Input / Output

Connections

8. Power Socket

9. Tilt-Adjustment Feet

10. Ventilation (inlet)

11. Ventilation (outlet)

8

English

Introduction

/

/

Control Panel

2 31

4

510

69

8

1. Power LED

2. Lamp LED

3. Temp LED

4. Enter / Help

5. Menu

6. Re-Sync

7. Keystone Correction

8. Four Directional Select Keys

9. Source

10. Power/Standby button

7

9

English

Introduction

AUDIO-IN

AUDIO OUT

VGA1-IN / YPbPr

RS-232C

VGA-OUT

VGA2-IN / YPbPr

HDMI

S-VIDEO

VIDEO

USB

Input/Output Connections

1

12

The interface

is subject to
model’s speci­cations.

Monitor loop

through only sup­port in VGA1-In/

YPbPr.

3 8

542

6 7

11

10

9

1. USB Connector (Connect to PC for Remote Mouse func-

tion)

2. HDMI Connector

3. Composite Video Input Connector

4. S-Video Input Connector

5. VGA-Out Connector (Monitor Loop-through Output)

6. VGA1-In/YPbPr Connector
(PC Analog Signal/Component Video Input/HDTV/YPbPr)

7. RS-232 Connector (9-pin DIN Type)

8. Audio Input connector (3.5mm mini jack)

9. Audio Output Connector (3.5mm Mini Jack)

10. KensingtonTM Lock Port

11. VGA2-In/YPbPr Connector
(PC Analog Signal/Component Video Input/HDTV/YPbPr)

12. Power Socket

10

English

Introduction

Remote Control

1

The interface

is subject to
model’s speci­cations.

2

3

4 9

5

6

20

21

22

23

24

25

27

26

28

1. LED Indicator

7

2. Power On/Off

3. Source

8

4. Mouse Left Click

5. Enter

6. Four Directional Select
Keys / Mouse control

7. Switch

8. Re-Sync

10

9. Mouse Right Click

10. Page Up

11

11. Page Down

12

12. Volume +/-

13. Menu

13

14. Zoom

14

15. AV mute

15

16. Video

17. 3D

16

18. VGA

17

19. USB

18

20. Laser Pointer

21. Keystone +/-

19

22. Brightness

23. HDMI

24. S-Video

25. Contrast

26. Numbered keypad
(for password input)

27. Freeze

28. Mode

29. Eco

+

29

11

English

Installation

AUDIO-IN

AUDIO OUT

VGA1-IN / YPbPr

RS-232C

VGA-OUT

VGA2-IN / YPbPr

HDMI

S-VIDEO

VIDEO

USB

mol ex

MOLEX

E62405SP

R

Connecting the Projector

Connect to Computer/Notebook

The interface

is subject to
model’s speci­cations.

Due to the

difference in
applications
for each

country, some
regions may

have different
accessories.

(*) Optional

accessory

2

3

4

6

5

1

7

8

Audio Output

1....................................................................................................Power Cord

2....................................................................................................*USB Cable

3...........................................................................................*DVI/HDMI Cable

4.....................................................................................................VGA Cable

5................................................................................................*RS232 Cable

6.........................................................................................*Audio Input Cable

7......................................................................................*Audio Output Cable

8........................................................................................*VGA Output Cable

12

English

Installation

AUDIO-IN

AUDIO OUT

VGA1-IN / YPbPr

RS-232C

VGA-OUT

VGA2-IN / YPbPr

HDMI

S-VIDEO

VIDEO

USB

E62405SP

R

The interface

is subject to
model’s speci­cations.

Connect to Video Sources

DVD Player, Set-top Box,

HDTV receiver

4

2 5

3

1

Due to the

difference in
applications
for each

country, some
regions may

have different
accessories.

(*) Optional

accessory

Composite Video Output

6

S-Video Output

5

7

Audio Output

1....................................................................................................Power Cord

2..................................................................................................*HDMI Cable

3................................................*15-Pin to 3 RCA Component/HDTV Adaptor

4.............................................................................*3 RCA Component Cable

5.................................................................................*Audio Cable Jack/RCA

6.............................................................................................. *S-Video Cable

7................................................................................*Composite Video Cable

13

English

Installation

When Power mode

/

(Standby) is set

to Eco (<0.5W),
the VGA output
and Audio pass-

through will be
deactivated when

the projector is in

standby.

Powering the projector On / Off

Powering On the Projector

1. Remove the lens cap. (optional) 

2. Securely connect the power cord and signal cable. When

connected, the POWER/STANDBY LED will turn Amber.

3. Turn on the lamp by pressing “ ” button either on the top of
the projector or on the remote. The POWER/STANDBY LED
will now turn Green. 

The startup screen will display in approximately 10 seconds.

The rst time you use the projector, you will be asked to
select the preferred language and power saving mode.

4. Turn on and connect the source that you want to display
on the screen (computer, notebook, video player, etc). The
projector will detect the source automatically. If not, push
menu button and go to “OPTIONS”.
Make sure that the “Source Lock” has been set to “Off”.

If you connect multiple sources at the same time, press the

“SOURCE” button on the control panel or direct source keys
on the remote control to switch between inputs.

Turn on the

projector rst and

then select the
signal sources.

2

POWER/STANDBY

1

Lens Cap (optional)

14

English

Installation

Powering Off the Projector

1. Press the “ ” button on the remote control or
on the control panel to turn off the projector.
The following message will be displayed on the screen.

Press the “ ” button again to conrm otherwise the

message will disappear after 15 seconds. When you press
the “ ” button for the second time, the fan will start cool­ing the system and will shut down.

2. The cooling fans continue to operate for about 10 seconds
for cooling cycle and the POWER/STANDBY LED will
Flash Green. When the POWER/STANDBY LED lights
solid Amber, the projector has entered standby mode.

If you wish to turn the projector back on, you must wait

until the projector has completed the cooling cycle and
has entered standby mode. Once in standby mode, simply
press “ ” button to restart the projector.

3. Disconnect the power cord from the electrical outlet and
the projector.

4. Do not turn on the projector immediately following a power
off procedure.

Contact the



nearest service
center if the
projector displays
these symptoms.
See pages
60-61 for more
information.

Warning Indicator

When the warning indicators (see below) come on,

the projector will automatically shutdown:

 “LAMP” LED indicator is lit red and if “POWER/STANDBY”

indicator ashes amber.

 “TEMP” LED indicator is lit red and if “POWER/STANDBY”

indicator ashes amber. This indicates the projector has

overheated. Under normal conditions, the projector can be
switched back on.

 “TEMP” LED indicator ashes red and if “POWER/STAND-

BY” indicator ashes amber.

Unplug the power cord from the projector, wait for 30 seconds
and try again. If the warning indicator light up again, please
contact your nearest service center for assistance.

15

English

Installation

Adjusting the Projected Image

Adjusting the Projector’s Height

The projector is equipped with elevator feet for adjusting
the image height.

1. Locate the adjustable foot you wish to modify on the

underside of the projector.

2. Rotate the adjustable ring clockwise to raise the projector
or counter clockwise to lower it. Repeat with the remaining

feet as needed.

Tilt-Adjustment Feet

Tilt-Adjustment Ring

16

English

Installation

Width

Height

Diagonal

Top View

Side View

Projection Distance (D)

Projection Distance (D)

Screen

Screen

Screen (W)

Screen (H)

Offset (Hd)

Adjusting the Projector’s Zoom / Focus

You may turn the zoom ring to zoom in or out. To focus the im­age, rotate the focus ring until the image is clear.

SVGA/XGA series: The projector will focus at distances from



3.28 to 39.4 feet (1.0 to 12.0 meters).

WXGA series: The projector will focus at distances from 3.28



to 39.4 feet (1.0 to 12.0 meters).

Adjusting Projection Image Size

SVGA/XGA series: Projection Image Size from 22.9” to



300.0” (0.6 to 7.6 meters).

Zoom Ring

Focus Ring

WXGA series: Projection Image Size from 27.2” to 301.0”



(0.7 to 7.6 meters).

17

English

Installation

SVGA/XGA

Diagonal length

(inch) size of

4:3 Screen

30.00 0.61 0.46 24.00 18.00 1.19 1.31 3.90 4.30 0.07 0.22

40.00 0.81 0.61 32.00 24.00 1.58 1.75 5.20 5.73 0.09 0.30

60.00 1.22 0.91 48.00 36.00 2.38 2.62 7.80 8.60 0.14 0.45

70.00 1.42 1.07 56.00 42.00 2.77 3.06 9.10 10.03 0.16 0.52

80.00 1.63 1.22 64.00 48.00 3.17 3.50 10.40 11.46 0.18 0.60

90.00 1.83 1.37 72.00 54.00 3.57 3.93 11.70 12.90 0.21 0.67

100.00 2.03 1.52 80.00 60.00 3.96 4.37 13.00 14.33 0.23 0.75

120.00 2.44 1.83 96.00 72.00 4.75 5.24 15.60 17.20 0.27 0.90

150.00 3.05 2.29 120.00 90.00 5.94 6.55 19.50 21.49 0.34 1.12

180.00 3.66 2.74 144.00 108.00 7.13 7.86 23.39 25.79 0.41 1.35

250.00 5.08 3.81 200.00 150.00 9.91 10.92 32.49 35.82 0.57 1.87

300.00 6.10 4.57 240.00 180.00 11.89 13.11 38.99 42.99 0.69 2.25

Screen Size W x H Projection Distance (D)

(m) (inch) (m) (feet)

Width Height Width Height wide tele wide tele (m) (feet)

 This table is for user’s reference only.

WXGA

Diagonal length

(inch) size of

16:10 Screen

30.00 0.65 0.40 25.44 15.90 1.00 1.10 3.29 3.60 0.05 0.16

40.00 0.86 0.54 33.92 21.20 1.34 1.46 4.38 4.80 0.07 0.22

60.00 1.29 0.81 50.88 31.80 2.00 2.20 6.57 7.21 0.10 0.33

70.00 1.51 0.94 59.36 37.10 2.34 2.56 7.67 8.41 0.12 0.38

80.00 1.72 1.08 67.84 42.40 2.67 2.93 8.76 9.61 0.13 0.44

90.00 1.94 1.21 76.32 47.70 3.00 3.30 9.86 10.81 0.15 0.49

100.00 2.15 1.35 84.80 53.00 3.34 3.66 10.95 12.01 0.17 0.55

120.00 2.58 1.62 101.76 63.60 4.01 4.39 13.14 14.41 0.20 0.66

150.00 3.23 2.02 127.20 79.50 5.01 5.49 16.43 18.02 0.25 0.82

180.00 3.88 2.42 152.64 95.40 6.01 6.59 19.71 21.62 0.30 0.99

250.00 5.38 3.37 212.00 132.50 8.35 9.15 27.38 30.03 0.42 1.37

300.00 6.46 4.04 254.40 159.00 10.02 10.98 32.85 36.03 0.50 1.64

Screen Size W x H Projection Distance (D)

(m) (inch) (m) (feet)

Width Height Width Height wide tele wide tele (m) (feet)

Offset (Hd)

Offset (Hd)

 This table is for user’s reference only.

18

English

User Controls

/

/

Control Panel & Remote Control

Control Panel

Using the Control Panel

POWER

RE-SYNC

Enter / Help

SOURCE

Menu

Four Directional

Select Keys

Keystone

Lamp LED Indicate the projector’s lamp status.

Temp LED Indicate the projector’s temperature status.

POWER/

STANDBY
LED

/

Refer to the “Power On/Off the Projector” section on

pages 13-14.

Automatically synchronize the projector to the input

source.

Conrm your item selection.

Help Menu (only available when OSD menu is not

shown).

Press “SOURCE” to select an input signal.

Press “Menu” to launch the on-screen display
(OSD) menu. To exit OSD, Press “Menu” again.

Use to select items or make adjust­ments to your selection.

Use to adjust image distortion caused
by tilting the projector. (±40 degrees)

Indicate the projector’s status.

19

English

User Controls

Remote Control

Using the Remote Control

Power

L Button

R Button

Page +

Page -

Enter

Source

Re-SYNC

Four Directional

Select Keys

PC/Mouse Control

Keystone +/-

Refer to the “Power On/Off the Projector”

section on pages 13-14.

Mouse left click.

Mouse right click.

Use this button to page up.

Use this button to page down.

Conrm your item selection.

Press “Source” to select an input signal.

Automatically synchronizes the projector to

the input source.

Use to select items or make

adjustments to your selection.

Use for emulation of USB
mouse via USB when you press “Switch”

button.

Adjust image distortion caused by tilting the

projector.

Volume +/-

Brightness

3D

Menu

HDMI

Adjust to increase / decrease the volume.

Adjust the brightness of the image.

Press the “3D” to turn the 3D OSD menu
on/off.

Press “Menu” to launch the on-screen

display (OSD) menu. To exit OSD, press

“Menu” again.

Press “HDMI” to choose HDMI source.

20

English

User Controls

Using the Remote Control

Freeze

AV mute

Press “Freeze” to pause the screen image.
Press this button again to unlock.

Momentarily turns off/on the audio and

video.

S-Video Press “S-Video” to choose S-Video source.

VGA

Video

Switch

Contrast

Mode

Zoom

Eco+

Press “VGA” to choose VGA sources.

Press “Video” to choose Composite video

source.

USB mouse switch.

Control the degree of difference between
the lightest and darkest parts of the picture.

Select the display mode from Presentation,

Bright, Movie, sRGB, Blackboard, Class­room, User and 3D.

Zoom in on an image.

Press buttons to alter zoom.

When Eco+ mode is activated, the bright­ness level of the content is automatically
detected to signicantly reduced lamp
power consumption (up to 70%) during
periods of inactivity.

AV mute: Save



up to 70% of the
lamp power when
AV mute is ap-

plied.

21

English

User Controls

/

Using the HELP button

The HELP function ensures easy setup and operation.

Press the “?” button on the remote control or press the



“HELP” button on the control panel to open the Help Menu.

22

English

User Controls

Help menu button functions only when no input source



is detected.

Please refer to the

“Troubleshooting”

section on pages

44-48 for more

details.

If input source is detected and help button is pressed, the



following pages will appear to help diagnose any problems.

23

English

User Controls

24

English

User Controls

On-screen Display Menus

The Projector has multilingual On-screen Display menus that
allow you to make image adjustments and change a variety of

settings.

How to operate

1. To open the OSD menu, press “Menu” on the Remote Control or

Projector Keypad.

2 When OSD is displayed, use

main menu. While making a selection on a particular page, press

or “Enter” key to enter sub menu.

3. Use

using key.

4. Select the next item to be adjusted in the sub menu and adjust as

described above.

5. Press “Enter” to conrm, and the screen will return to the main

menu.

6. To exit, press “MENU” again. The OSD menu will close and the

projector will automatically save the new settings.

keys to select the desired item and adjust the settings

keys to select any item in the

Main Menu

Sub Menu

Settings

25

English

User Controls

Main Menu Sub Menu Settings

Image

Display Mode

Brightness -50~50

Contrast -50~50

Sharpness 1~15

Color -50~50

Tint -50~50

Advanced Gamma

0~10

Color Temp. Warm / Medium / Cold

Color Settings

Color Space AUTO / RGB / YUV

AUTO / RGB (0-255) / RGB (16-235) / YUV

Input Source VGA1 / VGA2 / Video / S-Video / HDMI

Exit

Display

Format 4:3 / 16:9 or 16:10 / LBX / Native / AUTO

4:3 / 16:9-1 / 16:9-II / Native / AUTO
Edge Mask 0~10
Zoom -5~25 (80%~200%)
H Image Shift -50~50
V Image Shift -50~50
V Keystone -40~40

3D 3D Mode

3D Sync. Invert On / Off

Exit

Setup

Language

Screen Type 16:10 / 16:9

Projection

Menu Location

Signal Automatic On / Off

Phase (VGA) 0~31

Frequency (VGA) -5~5

H. Position (VGA) -5~5
V. Position (VGA) -5~5
Exit

ʳ

Security Security On / Off

Security Timer Month / Day / Hour
Change Password

ʳ

Exit

Presentation / Bright / Movie / sRGB /

Blackboard / Classroom / User / 3D

#1

#1

Film / Video / Graphics / Standard

BrilliantColor™

Red Gain / Green Gain / Blue Gain / Red

Bias / Green Bias / Blue Bias / Cyan /

Magenta / Yellow / Reset / Exit

#6

#3

#2

Off / DLP-Link / IR

#4

English / Deutsch / Français / Italiano /

Español / Português / Svenska /

Nederlands / Norsk/Dansk / Polski /

Suomi / Ɋɭɫɫɤɢɣ / İȜȜȘȞȚțȐ / Magyar /

ýeština / γέΎϓ / ϲΑήϋ /᜗

᧯խ֮ʳ/ 亞󰪠խ֮ʳ/

ֲ

ء፿!0ᾂ᝖᱑ʳ/ ࡷࡎ࡙/ Türkçe / ViӋt /

Bahasa Indonesia / Română

#3

#5

Menu Tree

26

English

User Controls

Main Menu Sub Menu Settings

Setup

Projector ID 0~99

Mute On / Off
Volume 0~10
Advanced Logo Default / Neutral

Closed Captioning Off / CC1 / CC2

Exit

Options

Source Lock On / Off
High Altitude On / Off
Information Hide On / Off
Keypad Lock On / Off
Test Pattern None / Grid / White Pattern
Background Color Black / Red / Blue / Green / White
Advanced Direct Power On On / Off

Auto Power Off (min.) 0~180
Sleep Timer (min.) 0~995
Quick Resume On / Off
Power Mode (Standby) Active / Eco

Exit

Lamp Settings Lamp Hours

Lamp Reminder On / Off
Brightness Mode Bright / Eco / Eco+
Lamp Reset Yes / No

Exit

Reset

Please note that the on-screen display (OSD) menus vary according to the

signal type selected and the projector model you are using.

(#1) “Color” and “Tint” are only supported in Video mode.

(#2) For XGA model only.

(#3) For WXGA model only. 16:9 or 16:10 depend on “Screen Type” setting.

(#4) “3D Sync Invert” is only available when 3D is enabled.

(#5) “Signal” is only supported in Analog VGA (RGB) signal.

(#6) For HDMI source device only.

27

English

User Controls

IMAGE

Display Mode

There are many factory presets optimized for various types of
images.

Presentation: Good color and brightness from PC input.



Bright: Maximum brightness from PC input.



Movie: For home theater.



sRGB: Standardised accurate color.



Blackboard: This mode should be selected to achieve optimum



color settings when projecting onto a blackboard (green).

Classroom: This mode is recommended for projecting in a



classroom.

User: User’s settings.



3D: Recommend setting for 3D mode enabled. Any further ad-



justments by the user in 3D will be saved in this mode for further

use.

Brightness

Adjust the brightness of the image.

Press the to darken image.



Press the to lighten the image.



Contrast

The contrast controls the degree of difference between the lightest
and darkest parts of the picture.

 Press the to decrease the contrast.

Press the to increase the contrast.



28

English

User Controls

Sharpness

Adjust the sharpness of the image.

 Press the to decrease the sharpness.
 Press the to increase the sharpness.

Color

“Color” and “Tint”

functions are only

supported under

Video mode.

Adjust a video image from black and white to fully saturated color.

 Press the to decrease the amount of saturation in the image.
 Press the to increase the amount of saturation in the image.

Tint

Adjust the color balance of red and green.

 Press the to increase the amount of green in the image.
 Press the to increase the amount of red in the image.

29

English

User Controls

IMAGE | Advanced

Gamma

This allows you to choose a degamma table that has been
ne-tuned to bring out the best image quality for the input.

 Film: for home theater.

Video: for video or TV source.



Graphics: for image source.



 Standard: for PC or computer source.

BrilliantColor™

This adjustable item utilizes a new color-processing algorithm and
system level enhancements to enable higher brightness while
providing true, more vibrant colors in picture. The range is from
“0” to “10”. If you prefer a stronger enhanced image, adjust toward
the maximum setting. For a smoother, more natural image, adjust
toward the minimum setting.

Color Temp

If set to cold temperature, the image looks more blue. (cold image)
If set to warm temperature, the image looks more red.

(warm image)

Color Settings

Press into the next menu as below and then use or to

select item.

 Red Gain/Green Gain/Blue Gain/Red Bias/Green Bias/Blue

Bias/Cyan/Magenta/Yellow: Use or to select Red, Green,

Blue, Cyan, Magenta and Yellow Colors.

 Reset: Choose “Yes” to return the factory default settings for

color adjustments.

30

English

User Controls

Color Space

Select an appropriate color matrix type from AUTO, RGB,

(*) For HDMI only.

RGB(0-255)

Input Source

Use this option to enable / disable input sources. Press to enter
the sub menu and select which sources you require. Press “Enter”
to finalize the selection. The projector will not search for inputs that

are not selected.

(*)

,RGB(16-235)

(*)

or YUV.

31

English

User Controls

DISPLAY

Format

Use this function to choose your desired aspect ratio.

SVGA/XGA

4:3: This format is for 4×3 input sources.



16:9-I: This format is for 16×9 input sources, like HDTV and



DVD enhanced for Wide screen TV. (576i/p)

16:9-II: This format is for 16×9 input sources, like HDTV and



DVD enhanced for Wide screen TV. (480i/p)

Native: This format displays the original image without any



scaling.

AUTO: Automatically selects the appropriate display format.



When input is 4:3, the image is displayed as 4:3. When input is
16:9 above, the image is displayed as 16:9- I

Aspect ratio

(source detected)

4:3 800 x 600 center 1024 x 768 center

16:9-I 800 x 450 center 1024 x 576 center

16:9-II 800 x 480 center 854 x 480 center

Native

SVGA model XGA model

No resize image, 1:1 mapping and

centered. This format shows the

original image without scaling.

Resize image

32

English

User Controls

WXGA

4:3: This format is for 4×3 input sources.



16:9: This format is for 16×9 input sources, like HDTV and DVD



enhanced for Wide screen TV.

16:10: This format is for 16×10 input sources, like widescreen

16:9 or 16:10

depend on “Screen

Type” setting.



laptops.

LBX: This format is for non-16x9, letterbox source and for users



who use external 16x9 lens to display 2.35:1 aspect ratio using

full resolution.

Native: This format displays the original image without any



scaling.

AUTO: Automatically selects the appropriate display format.



16:10 Screen 480i/p 576i/p 1080i/p 720p PC

4:3 1066 x 800 center

16:10 1280 x 800 center

LBX

Native

1280 x 960 center, then get the central 1280 x 800 image

1:1 mapping

centered.

to display

1:1 map-

ping (960 x

540) display

1280 x 800

1280 x 720

center

1:1

mapping

centered.

16:9 Screen 480i/p 576i/p 1080i/p 720p PC

4:3 960 x 720 center

16:9 1280 x 720 center

LBX

Native

1280 x 960 center, then get the central 1280 x 720 image

1:1 mapping

centered.

to display

1:1 map-

ping (960 x

540) display

1280 x 720

1280 x 720

center

1:1

mapping

centered.

33

English

User Controls

Each I/O has

different setting of

“Edge mask”.

“Edge mask” and

“Zoom” can’t work at
same time.

Edge Mask

Edge mask function removes the noise in a video image. Edge
mask the image to remove video encoding noise on the edge of

video source.

Zoom

 Press the to reduce the size of an image.

 Press the to magnify an image on the projection screen.

H Image Shift

Shift the projected image position horizontally.

V Image Shift

Shift the projected image position vertically.

V Keystone

Press the or to adjust image distortion vertically. If the image
looks trapezoidal, this option can help make the image rectangular.

34

English

User Controls

DISPLAY | 3D

3D Mode

Off: Select “Off” to turn 3D settings off for 3D images.



DLP Link: Select “DLP Link” to use optimized settings for DLP



“IR” options may

vary according to
model.

“3D Sync Invert” is

only available when

3D is enabled and

this mode 3D is for
DLP link glass only.

Compatible 3D

source, 3D content
and active shutter

glasses are required
for 3D viewing.

Link 3D images.

IR: Select “IR” to use optimized settings for IR-based 3D



images.

3D Sync. Invert

Press the “On” to invert left and right frame contents.



Press the “Off” for default frame contents.



35

English

User Controls

“SETUP” options

may vary according
to model.

SETUP

Language

Choose the multilingual OSD menu. Press or into the sub
menu and then use the or key to select your preferred

language. Press “Enter” to nalize the selection.

Rear-Desktop and

Rear-Ceiling are

to be used with a

translucent screen.

Projection

 Front-Desktop

This is the default selection. The image is projected straight on

the screen.

 Front-Ceiling

When selected, the image will turn upside down.

 Rear-Desktop

When selected, the image will appear reversed.

36

English

User Controls

“Screen Type” is for

WXGA only.



Rear-Ceiling

When selected, the image will appear reversed in upside down

position.

Menu Location

Choose the menu location on the display screen.

Screen Type

Choose the screen type from16:10 or 16:9.

Projector ID

ID denition can be set up by menu (range 0-99), and allow user
control an individual projector by RS232. Refer to pages 55-58 for
the complete list of RS232 commands.

Mute

Choose the “On” to turn mute on.



Choose the “Off” to turn mute off.



Volume

 Press the to decrease the volume.

 Press the to increase the volume.

37

English

User Controls

SETUP | Signal

“Signal” is only

supported in Analog
VGA (RGB) signal.

(RGB)

Automatic

Automatically selects the signal. If you use this function, the
Phase, frequency items are grayed out, and if Signal is not auto­matic, the phase, frequency items will appear for user to manually
tune and saved in settings after that for next time projector turns

off and on again.

Phase

Synchronize the signal timing of the display with the graphic card.
If the image appears to be unstable or ickers, use this function to

correct it.

Frequency

Change the display data frequency to match the frequency of
your computer’s graphic card. Use this function only if the image
appears to icker vertically.

H. Position

Press the to move the image left.



Press the to move the image right.



V. Position

Press the to move the image down.



Press the to move the image up.



38

English

User Controls

SETUP | Security

Security

On: Choose “On” to use security verication when the turning



Off: Choose “Off” to be able to switch on the projector without



Security Timer

Use this function to set the how long (Month/Day/Hour) the

Password default

value is “1234” (rst
time).

projector can be used. Once this time has elapsed you will be
requested to enter your password again.

Change Password

First time:



1. Press “ ” to set the password.

2. The password has to be 4 digits.

3. Use number button on the remote to enter your new

Change Password:



1. Press “ ” to input old password.

2. Use number button to enter current password and then

3. Enter new password (4 digits in length) using the number

4. Enter new password again and press “ ” to conrm.

on the projector.

password verication.

password and then press “ ” key to conrm your
password.

press “ ” to conrm.

buttons on the remote, then press “ ” to conrm.

39

English

User Controls

If the incorrect password is entered 3 times, the projector will



automatically shut down.

If you have forgotten your password, please contact your local



ofce for support.

40

English

User Controls

SETUP | Advanced

Logo

Use this function to set the desired startup screen. If changes are

made they will take effect the next time the projector is powered

on.

Default: The default startup screen.



Neutral: Logo is not displayed on startup screen.



Closed Captioning

Use this function to set the desired startup screen. If changes are

made they will take effect the next time the projector is powered

on.

Off: select “off” to turn off the closed captioning feature.



CC1:CC1 language: American English.



CC2:CC2 language (depending on the TV channel of the



user):Spanish, French, Portuguese, German, Danish.

41

English

User Controls

OPTIONS

Source Lock

On: The projector will only search current input connection.



Off: The projector will search for other signals if the current



High Altitude

When “On” is selected, the fans will spin faster. This feature is
useful in high altitude areas where the air is thin.

Information Hide




input signal is lost.

On: Choose “On” to hide the info message.

Off: Choose “Off” to show the “searching” message.

To turn off the key-

pad lock, press and
hold “Enter” key on

top of the projector
for 5 seconds.

Keypad Lock

When the keypad lock function is “On”, the control panel will be
locked however, the projector can be operated by the remote
control. By selecting “Off”, you will be able to reuse the control

panel.

Test Pattern

Display a test pattern. There are Grid, White pattern and None.

Background Color

Use this feature to display a “Black”, “Red”, “Blue”, “Green” or
“White”, screen when no signal is available.

Reset

Choose “Yes” to return the display parameters on all menus to the
factory default settings.

42

English

User Controls

OPTIONS |

Advanced

Direct Power On

Choose “On” to activate Direct Power mode. The projector will
automatically power on when AC power is supplied, without
pressing the “ ” key on the projector control panel or on the
remote control.

Auto Power Off (min)

Sets the countdown timer interval. The countdown timer will start,
when there is no signal being sent to the projector. The projector
will automatically power off when the countdown has nished (in
minutes).

When Power mode

(Standby) is set

to Eco (<0.5W),
the VGA output
and Audio pass-

through will be
deactivated when

the projector is in

standby.

Sleep Timer (min)

Sets the countdown timer interval. The countdown timer will start,
with or without a signal being sent to the projector. The projector
will automatically power off when the countdown has nished (in
minutes).

Quick Resume

On: If the projector is accidentally turned off, this feature allows



the projector to be instantly powered on again, if selected
within a period of 100 seconds.

Off: The fan will start cooling the system immediately when user



turns off the projector.

Power Mode (Standby)

Eco.: Choose “Eco.” to save power dissipation further < 0.5W.



Active: Choose “Active” to return to normal standby and the



VGA out port will be enabled.

43

English

User Controls

Lamp Settings

When ambient tem-

perature is over 40°C
in operating, the

projector will switch
to Eco automatically.

OPTIONS |

Lamp Hours

Display the projection time.

Lamp Reminder

Choose this function to show or to hide the warning message
when the changing lamp message is displayed.
The message will appear 30 hours before suggested replacement

of lamp.

Brightness Mode

BRIGHT: Choose “BRIGHT” to increase the brightness.



Eco.: Choose “Eco.” to dim the projector lamp which will lower



power consumption and extend the lamp life.

Eco+: When Eco+ mode is activated, the brightness level of the



content is automatically detected to signicantly reduced
lamp power consumption (up to 70%) during periods of

inactivity.

Lamp Reset

Reset the lamp hour counter after replacing the lamp.

44

English

Appendices

Troubleshooting

If you experience a problem with your projector,

please refer to the following information. If a
problem persists, please contact your local
reseller or service center.

No image appears on-screen

Ensure all the cables and power connections are correctly and



securely connected as described in the “Installation” section.

Ensure all the pins of connectors are not bent or broken.



Check if the projection lamp has been securely installed. Please



refer to the “Replacing the lamp” section.

Make sure you have removed the lens cap and the projector is



switched on.

Ensure that the “AV mute” feature is not turned on.



Partial, scrolling or incorrectly displayed image



Press “Re-SYNC” on the remote.

If you are using a PC:



For Windows 95, 98, 2000, XP, Windows 7:

1. Open the “My Computer” icon, the “Control Panel” folder, and
then double click on the “Display” icon.

2. Select the “Settings” tab.

3. Verify that your display resolution setting is lower than or equal

to UXGA (1600 × 1200).

4. Click on the “Advanced Properties” button.

If the projector is still not projecting the whole image, you will also
need to change the monitor display you are using. Refer to the
following steps.

5. Verify the resolution setting is lower than or equal to UXGA

(1600 × 1200).

6. Select the “Change” button under the “Monitor” tab.

45

English

Appendices

7. Click on “Show all devices”. Next, select “Standard monitor
types” under the SP box; choose the resolution mode you need

under the “Models” box.

8. Verify that the resolution setting of the monitor display is lower
than or equal to UXGA (1600 × 1200).

If you are using a Notebook:



1. First, follow the steps above to adjust resolution of the
computer.

2. Press the appropriate keys listed below for your notebook
manufacturer to send signal out from notebook to projector.
Example: [Fn]+[F4]

Acer  [Fn]+[F5]
Asus  [Fn]+[F8]
Dell  [Fn]+[F8]

Gateway  [Fn]+[F4]

Mac Apple:
System Preference  Display  Arrangement  Mirror
display

If you experience difculty changing resolutions or your monitor



freezes, restart all equipment including the projector.

The screen of the Notebook or PowerBook computer is not

IBM/Lenovo  [Fn]+[F7]
HP/Compaq  [Fn]+[F4]

NEC  [Fn]+[F3]
Toshiba  [Fn]+[F5]

displaying your presentation

If you are using a Notebook PC



Some Notebook PCs may deactivate their own screens when a
second display device is in use. Each has a different way to be
reactivated. Refer to your computer’s manual for detailed
information.

Image is unstable or ickering

Use “Phase” to correct it. See page 37 for more information.



Change the monitor color setting on your computer.



Image has vertical ickering bar

Use “Frequency” to make an adjustment. See page 37 for more



information.

Check and re-congure the display mode of your graphic card to



make it compatible with the projector.

46

English

Appendices

Image is out of focus

Make sure the lens cap is removed.



Adjust the Focus Ring on the projector lens.



Make sure the projection screen is between the required distance.



See page 17.

The image is stretched when displaying 16:9 DVD title

When you play anamorphic DVD or 16:9 DVD, the projector will



show the best image when the projector display mode is set to
16:9 in the OSD.

If you play 4:3 format DVD titles, please change the format to 4:3



in the projector OSD.

If the image is still stretched, you will also need to adjust the



aspect ratio by referring to the following:

Please setup the display format as 16:9 (wide) aspect ratio type



on your DVD player.

Image is too small or too large

Move the projector closer to or further from the screen.



Press “Menu” button on the remote control or projector panel, go



to “DISPLAY  Format” and try the different settings.

Image has slanted sides

If possible, reposition the projector so that it is horizontally



centered on the screen and below the bottom of the screen.

Press “Keystone +/-” button on the remote control or press



“ / ” on the projector panel, until the sides are vertical.

Image is reversed

Select “SETUP  Projection” from the OSD and adjust the



projection direction.

47

English

Appendices

The projector stops responding to all controls

If possible, turn off the projector, then unplug the power cord and



wait at least 60 seconds before reconnecting power.

Check that “Keypad Lock” is not activated by trying to control the



projector with the remote control.

Lamp burns out or makes a popping sound

When the lamp reaches its end of life, it will burn out and may



make a loud popping sound. If this happens, the projector will not
turn on until the lamp module has been replaced. To replace the
lamp, follow the procedures in the “Replacing the Lamp” section on

pages 49-50.

LED lighting message

Steady light 

No light 

Message

Standby State
(Input power cord)

Power on (Warming)

Lamp lighting Green

Power off (Cooling)

Quick Resume(100

secs)

Error (Over Temp.)

Error (Fan fail)

Error (Lamp fail)

＊ POWER/STANDBY LED be ON when OSD appears, be OFF when OSD disappears.

POWER/STAND-

BY LED

(Green/Amber) (Red) (Red)

Amber

Flashing

Green

Flashing

Green

Flashing

Green

Flashing

Amber

Flashing

Amber

Flashing

Amber

Temp-LED

Flashing

Lamp-LED

48

English

Appendices

On Screen Messages

Temperature warning:



Fan failed:



Lamp warning:



Out of display range:



If the remote control does not work

Check the operating angle of the remote control is within ±15°



both horizontally and vertically of one of the IR receivers on the

projector.

Make sure there are not any obstructions between the remote



control and the projector. Move to within 7 m (±0°) of the projector.

Make sure the batteries are inserted correctly.



Replace batteries if they are exhausted.



49

English

Appendices

Replacing the lamp

The projector automatically detects the lamp life. When the
lamp life is nearing the end of use, you will receive a warning
message.

When you see this message, please contact your local reseller
or service center to change the lamp as soon as possible.
Make sure the projector has been cooled down for at least 30
minutes before changing the lamp.

Warning: If ceiling mounted, please use caution when

opening the lamp access panel. It is recommended to wear
safety glasses if changing the bulb when ceiling mounted.
“Caution must be used to prevent any loose parts from fall-

ing out of projector.”

Warning: Lamp compartment may be hot! Allow it to cool

down before changing the lamp!

Warning: To reduce the risk of personal injury, do not drop

the lamp module or touch the lamp bulb. The bulb may shat­ter and cause injury if it is dropped.

50

English

Appendices

1

2

3

4

5

The screws on the

lamp cover and the
lamp cannot be
removed.

The projector

cannot be turned

on if the lamp

cover has not been

placed back on the

projector.

Do not touch the

glass area of the

lamp. Hand oil can
cause the lamp to
shatter. Use a dry

cloth to clean the

lamp module if it
was accidentally

touched.

Lamp Replacement Procedure:

1. Switch off the power to the projector by pressing the “ ” button.

2. Allow the projector to cool down for at least 30 minutes.

3. Disconnect the power cord.

4. Unscrew the one screw on the cover. 1

5. Lift up and remove the cover. 2

6. Unscrew the two screws on the lamp module. 3

7. Lift up the lamp handle 4 and remove the lamp module slowly and carefully. 5

To replace the lamp module, reverse the previous steps.

8. Turn on the projector and use “Lamp Reset” after the lamp module is

replaced.

Lamp Reset: (i) Press “Menu”  (ii) Select “OPTIONS”  (iii) Select

“Lamp Settings”  (iv) Select “Lamp Reset”  (v) Select “Yes”.

51

English

Appendices

Compatibility Modes

Computer Compatibility



For widescreen

resolution
(WXGA), the

compatibility

support is
dependent on

Notebook/PC
models.

120Hz input

signals may be

dependent on
graphics cards
support.

Please note that

using resolu­tions other than
native 800 x
1024 (SVGA),
1024 x 768 (XGA

model), 1280

x 800 (WXGA

model) may result
in some loss of
image clarity.

Mode Resolution

Anglog/Digital

H-Sync (KHz) V-Sync (Hz)

VGA 640 × 350 31.50 70 V V

VGA 640 × 350 37.90 85 V V

VGA 720 × 350 31.50 70 V

VGA 640 × 400 31.50 70 V

VGA 640 × 400 37.90 85 V V

VGA 720 × 400 31.50 70 V V

VGA 720 × 400 37.90 85 V V

720 × 576 - 50 V

720 × 576 - 60 V

VGA 640 × 480 31.50 60 V V

VGA 640 × 480 - 67 V V

VGA 640 × 480 37.90 72 V V

VGA 640 × 480 37.50 75 V V

VGA 640 × 480 43.30 85 V

SVGA 800 × 600 35.20 56 V V

SVGA 800 × 600 37.90 60 V V

SVGA 800 × 600 46.90 75 V V

SVGA 800 × 600 48.10 72 V V

SVGA 800 × 600 - 80 V

SVGA 800 × 600 53.70 85 V

SVGA 800 × 600 - 120 V

832 × 624 - 72 V

832 × 624 - 75 V V

XGA 1024 × 576 - 50 V

XGA 1024 × 576 - 60 V

XGA 1024 × 768 48.40 60 V V

XGA 1024 × 768 56.50 70 V V

XGA 1024 × 768 57.70 72 V

SVGA/

XGA

WXGA

52

English

Appendices

Mode Resolution

Anglog/Digital

H-Sync (KHz) V-Sync (Hz)

XGA 1024 × 768 60.00 75 V V

XGA 1024 × 768 68.70 85 V

XGA 1024 × 768 - 120 V

1152 × 864 - 60 V

1152 × 864 - 70 V

1152 × 864 - 75 V

1152 × 864 - 85 V

1152 × 870 - 75 V V

HD720 1280 x 720 - 50 V

HD720 1280 x 720 - 60 V

HD720 1280 x 720 - 75 V

HD720 1280 x 720 - 85 V

HD720 1280 x 720 - 120 V

WXGA 1280 x 768 47.40 60 V

WXGA 1280 x 768 - 70 V

WXGA 1280 x 768 - 75 V

WXGA 1280 x 768 - 85 V

WXGA-800 1280 x 800 - 60 V V

SXGA 1280 x 1024 64.00 60 V V

SXGA 1280 x 1024 80.00 75 V

SXGA 1280 x 1024 91.10 85 V

1366 x 768 60 - V

1400 x 900 60 55.935 V

SXGA+ 1400 x 1050 - 60 V V

1680 x 1050 60 - V

UXGA 1600 × 1200 75.00 60 V V

HDTV 1920 x 1080 33.80 30 V V

HDTV 1920 × 1080 28.10 25 V

HDTV 1920 x 1080i - 50/60 V V

HDTV 1920 x 1080p - 24/25/30/50/60 V V

HDTV 1280 x 720 45.00 60 V V

HDTV 1280 x 720p - 50/60 V V

SVGA/

XGA

WXGA

53

English

Appendices

Mode Resolution

SDTV 720 × 576 31.30 50 V

SDTV 720 × 576i - 50 V V

SDTV 720 × 576p - 50 V V

SDTV 720 × 480 31.50 60 V

SDTV 720 × 480i - 60 V V

SDTV 720 × 480p - 60 V V

Computer Compatibility



Mode Resolution V-Sync (Hz) H-Sync (KHz)

MAC LC 13” 640 × 480 66.66 34.98

MAC II 13” 640 × 480 66.68 35.00

MAC 16” 832 × 624 74.55 49.73

MAC 19” 1024 × 768 75 60.24

MAC 1152 × 870 75.06 68.68

MAC G4 640 × 480 60 31.35

i MAC DV 1024 × 768 75 60.00

i MAC DV 1152 × 870 75 68.49

Anglog/Digital

H-Sync (KHz) V-Sync (Hz)

SVGA/

XGA

WXGA

Video Compatibility



NTSC M/J, 3.58MHz, 4.43 MHz

PAL B, D, G, H, I, M, N (4.43 MHz)

SECAM B, D, G, K, K1, L (4.25/4.4 MHz)

SDTV 480i/p, 576i/p,

HDTV 720p@50Hz/60Hz, 1080i@50Hz/60Hz, 1080p@50Hz/60Hz

54

English

Appendices

12345

6789

RS232 shell is

grounded.

RS232 Commands and Protocol Function List

RS232 Pin Assignments

Pin no.

1 N/A

2 RXD

3 TXD

4 N/A

5 GND

6 N/A

7 N/A

8 N/A

9 N/A

Spec.

(from projector side)

55

English

Appendices

Optoma ES555/EX555/ES556/EX556/EW556 RS232 & Telnet Command

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Baud Rate : 9600 Note : There i s a <CR> after all ASCII commands
Data Bits: 8 0D is the HEX code for <CR> in ASCII code
Parity: None
Stop Bits: 1
Flow Control : None
UART16550 FIFO: Disable
Projector Return (Pass): P
Projector Return (Fail): F XX=01ˀ99, projector's ID, XX=00 is for all projectors
Note : the ~XX must be set as ~00 wh en use on telnet command no matter what ID projector has. eg: telnet with ~0004 1 can execute Freeze function but ~3804 1 can't.

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­SEND to projector (telnet supported)

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

232 ASCII Code HEX Code Function Description

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX00 1 7E 30 30 30 30 20 31 0D Power ON
~XX00 0 7E 30 30 30 30 2 0 30 0D Power OFF (0/2 for backw ard compatible)
~XX00 1 ~nnnn 7E 30 30 30 30 20 31 20 a 0D Power ON with Password ~nnnn = ~0000 (a=7E 30 30 30 30)

~9999 (a=7E 39 39 39 39)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX01 1 7E 30 30 30 31 20 31 0D Resync
~XX02 1 7E 30 30 30 32 20 31 0D AV Mute On
~XX02 0 7E 30 30 30 32 20 30 0D Off (0/2 for backward compatible)
~XX03 1 7E 30 30 30 33 2 0 31 0D Mute On
~XX03 0 7E 30 30 30 33 20 3 0 0D Off (0/2 for backward compatible)
~XX04 1 7E 30 30 30 34 20 3 1 0D Freeze
~XX04 0 7E 30 30 30 34 20 30 0D Unfreeze (0/2 for backward compatible)
~XX05 1 7E 30 30 30 35 2 0 31 0D Zoom Plus
~XX06 1 7E 30 30 30 36 2 0 31 0D Zoom Minus
~XX12 1 7E 30 30 31 32 2 0 31 0D Direct Source Commands HDMI (for ES556/EX556/EW556 )
~XX12 5 7E 30 30 31 32 2 0 35 0D VGA1
~XX12 6 7E 30 30 31 32 20 36 0D VGA 2
~XX12 8 7E 30 30 31 32 2 0 38 0D VGA1 Component
~XX12 9 7E 30 30 31 32 20 3 9 0D S-Video
~XX12 10 7E 30 30 31 32 20 31 30 0D Video
~XX12 13 7E 30 30 31 32 20 31 33 0D VGA 2 Component

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX20 1 7E 30 30 32 30 20 31 0D Display Mode Presentation
~XX20 2 7E 30 30 32 30 2 0 32 0D Bright
~XX20 3 7E 30 30 32 30 2 0 33 0D Movie
~XX20 4 7E 30 30 32 30 20 34 0D sRGB
~XX20 5 7E 30 30 32 30 20 3 5 0D User
~XX20 7 7E 30 30 32 30 20 37 0D Blackboard
~XX20 8 7E 30 30 32 30 2 0 38 0D Classroom
~XX20 9 7E 30 30 32 30 2 0 39 0D 3D

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX21 n 7E 30 30 32 31 20 a 0D Brightness n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX22 n 7E 30 30 32 32 20 a 0D Contrast n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX23 n 7E 30 30 32 33 20 a 0D Sharpness n = 1 (a=31) ~ 15 (a=31 35)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX24 n 7E 30 30 32 34 20 a 0D Color Settings Red Gain n = -50 (a=2D 35 30) ~ 50 (a=35 3 0)
~XX25 n 7E 30 30 32 35 20 a 0D Green Gain n = -50 (a=2 D 35 30) ~ 50 (a=35 30)
~XX26 n 7E 30 30 32 36 20 a 0D Blue Gain n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX27 n 7E 30 30 32 37 20 a 0D Red Bias n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX28 n 7E 30 30 32 38 20 a 0D Green Bias n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX29 n 7E 30 30 32 39 20 a 0D Blue Bias n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX30 n 7E 30 30 33 30 20 a 0D Cyan n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX31 n 7E 30 30 33 31 20 a 0D Yellow n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX32 n 7E 30 30 33 32 20 a 0D Magenta n = -50 (a=2 D 35 30) ~ 50 (a=35 30)
~XX33 1 7E 30 30 33 33 20 31 0D Reset

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX34 n 7E 30 30 33 34 2 0 a 0D BrilliantColorTM n = 0 (a=30) ~ 10 (a=31 30)
~XX35 1 7E 30 30 33 35 2 0 31 0D Degamma Film
~XX35 2 7E 30 30 33 35 2 0 32 0D Video
~XX35 3 7E 30 30 33 35 2 0 33 0D Graphics
~XX35 4 7E 30 30 33 35 2 0 34 0D Standard

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX36 1 7E 30 30 33 36 20 31 0D Color Temp. Warm
~XX36 2 7E 30 30 33 36 2 0 32 0D Medium
~XX36 3 7E 30 30 33 36 2 0 33 0D Cold
~XX37 1 7E 30 30 33 37 2 0 31 0D Color Space Auto
~XX37 2 7E 30 30 33 37 2 0 32 0D RGB\ RGB(0-255)
~XX37 3 7E 30 30 33 37 2 0 33 0D YUV
~XX37 4 7E 30 30 33 37 2 0 34 0D RGB(16 - 235)

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

RS232 Protocol Function List

Baud Rate : 9600
Data Bits: 8

XX=00-99, projector's ID,
XX=00 is for all projectors

Parity: None

1. There is a <CR> after
all ASCII commands.

2. 0D is the HEX code

for <CR> in ASCII

code.

Stop Bits: 1
Flow Control : None
UART16550 FIFO: Disable
Projector Return (Pass): P
Projector Return (Fail): F

56

English

Appendices

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX45 n 7E 30 30 34 34 20 a 0D Color (Saturation) n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX44 n 7E 30 30 34 35 20 a 0 D Tint n = -50 (a=2D 35 30) ~ 50 (a=35 30)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX60 1 7E 30 30 36 30 20 31 0D Format 4:3
~XX60 2 7E 30 30 36 30 2 0 32 0D 16:9-l
~XX60 3 7E 30 30 36 30 20 33 0D 16:9-ll/16:10(EW556)
~XX60 5 7E 30 30 36 30 20 35 0D LBX
~XX60 6 7E 30 30 36 30 2 0 36 0D Native
~XX60 7 7E 30 30 36 30 2 0 37 0D Auto

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX61 n 7E 30 30 36 31 2 0 a 0D Edge mask n = 0 (a=30) ~ 10 (a=31 30)
~XX62 n 7E 30 30 36 32 20 a 0D Zoom n = -5 (a=2D 3 5) ~ 25 (a=32 35)
~XX63 n 7E 30 30 36 33 20 a 0D H Image Shift n = -50 ( a=2D 35 30) ~ 50 (a=35 30)
~XX64 n 7E 30 30 36 34 20 a 0D V Image Shift n = -50 ( a=2D 35 30) ~ 50 (a=35 30)
~XX66 n 7E 30 30 36 36 20 a 0D V Keystone n = -40 (a=2D 34 30) ~ 40 (a=34 30)
~XX230 3 7E 30 30 32 33 30 20 31 0D 3D Mode IR
~XX230 1 7E 30 30 32 33 30 20 31 0D 3D Mode DLP-Link
~XX230 0 7E 30 30 32 33 30 20 30 0D 3D Mode Off (0/2 for backward compatible)
~XX231 1 7E 30 30 32 33 31 20 31 0D 3D Sync Invert On
~XX231 0 7E 30 30 32 33 31 20 30 0D 3D Sync Invert Off (0/2 for backward compatibl e)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX70 1 7E 30 30 37 30 2 0 31 0D Language English
~XX70 2 7E 30 30 37 30 2 0 32 0D German
~XX70 3 7E 30 30 37 30 2 0 33 0D French
~XX70 4 7E 30 30 37 30 20 3 4 0D Italian
~XX70 5 7E 30 30 37 30 2 0 35 0D Spanish
~XX70 6 7E 30 30 37 30 2 0 36 0D Portuguese
~XX70 7 7E 30 30 37 30 2 0 37 0D Polish
~XX70 8 7E 30 30 37 30 2 0 38 0D Dutch
~XX70 9 7E 30 30 37 30 2 0 39 0D Swedish
~XX70 10 7E 30 30 37 30 20 31 30 0D Norwegian/Danish
~XX70 11 7E 30 30 37 30 20 31 31 0D Finnish
~XX70 12 7E 30 30 37 30 20 31 32 0D Greek
~XX70 13 7E 30 30 37 30 20 31 33 0D Traditional Chinese
~XX70 14 7E 30 30 37 30 20 31 34 0D Simplified Chinese
~XX70 15 7E 30 30 37 30 20 31 35 0D Japanese
~XX70 16 7E 30 30 37 30 20 31 36 0D Korean
~XX70 17 7E 30 30 37 30 20 31 37 0D Russian
~XX70 18 7E 30 30 37 30 20 31 38 0D Hungarian
~XX70 19 7E 30 30 37 30 20 31 39 0D Czechoslovak
~XX70 20 7E 30 30 37 30 20 32 30 0D Arabic
~XX70 21 7E 30 30 37 30 20 32 31 0D Thai
~XX70 22 7E 30 30 37 30 20 32 32 0D Turkish
~XX70 23 7E 30 30 37 30 20 32 33 0D Farsi
~XX70 25 7E 30 30 37 30 20 32 35 0D Vietnamese
~XX70 26 7E 30 30 37 30 20 32 36 0D Indonesia
~XX70 27 7E 30 30 37 30 20 32 37 0D Romanian
~XX71 1 7E 30 30 37 31 2 0 31 0D Projection Front- Desktop
~XX71 2 7E 30 30 37 31 20 3 2 0D Rear-Desktop
~XX71 3 7E 30 30 37 31 2 0 33 0D Front-Ceiling
~XX71 4 7E 30 30 37 31 20 34 0D Rear-Ceiling
~XX72 1 7E 30 30 37 32 2 0 31 0D Menu Location Top Left
~XX72 2 7E 30 30 37 32 2 0 32 0D Top Right
~XX72 3 7E 30 30 37 32 2 0 33 0D Centre
~XX72 4 7E 30 30 37 32 2 0 34 0D Bottom Left
~XX72 5 7E 30 30 37 32 20 35 0D Bottom Right

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­ʳ(EW556 only)
~XX90 1 7E 30 30 39 31 2 0 31 0D Screen Type 16:10
~XX90 0 7E 30 30 39 31 2 0 30 0D 16:9

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX73 n 7E 30 30 37 33 20 a 0D Signal Frequency n = -5 (a=2D 3 5) ~ 5 (a=35) By signal
~XX91 n 7E 30 30 39 31 20 a 0D Automatic n = 0 disable; n = 1 enable
~XX74 n 7E 30 30 37 34 20 a 0D Phase n = 0 (a=30) ~ 31 (a=33 31) By signal
~XX75 n 7E 30 30 37 35 20 a 0D H. Position n = -5 (a=2D 35) ~ 5 (a=35) By timing
~XX76 n 7E 30 30 37 36 20 a 0D V. Position n = -5 (a=2D 35) ~ 5 (a=35) By timing
~XX77 n 7E 30 30 37 37 20 aabbcc 0D Security Securit y Timer Month/Day/Hour n = mm/dd/hh

mm= 00 (aa=30 30) ~ 12 (aa=31 32)
dd = 00 (bb=30 30) ~ 30 (bb=3 3 30)

hh= 00 (cc=30 30) ~ 24 (cc=32 34)
~XX78 1 7E 30 30 37 38 2 0 31 0D Security Settings Enable
~XX78 0 ~nnnn 7 E 30 30 37 38 20 32 20 a 0D Disable(0/2 for backward co mpatible)

~nnnn = ~0000 (a=7E 30 30 30 30)
~9999 (a=7E 39 39 39 39 )

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX79 n 7E 30 30 37 39 20 a 0D Projector ID n = 00 (a=30 30) ~ 99 (a=39 39)

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

57

English

Appendices

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­(for ES556/EX555/EX556/EW556)
~XX80 1 7E 30 30 38 30 2 0 31 0D Mute On
~XX80 0 7E 30 30 38 30 20 3 0 0D Off (0/2 for backward compatible)
~XX81 n 7E 30 30 38 31 2 0 a 0D Volume n = 0 (a=30) ~ 10 (a=31 30)
~XX82 1 7E 30 30 38 32 20 31 0D Logo Defaul t
~XX82 3 7E 30 30 38 32 2 0 33 0D Neutral
~XX88 0 7E 30 30 38 38 20 3 0 0D Closed Captioning Off
~XX88 1 7E 30 30 38 38 2 0 31 0D cc1
~XX88 2 7E 30 30 38 38 2 0 32 0D cc2

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX100 1 7E 30 30 31 30 30 20 31 0D Source Lock On
~XX100 0 7E 30 30 31 30 30 20 30 0D Off (0/2 for backward compatible)
~XX100 3 7E 30 30 31 30 30 20 33 0D Next Source
~XX101 1 7E 30 30 31 30 31 20 31 0D High Altitude On
~XX101 0 7E 30 30 31 30 31 20 30 0D Off (0/2 for backward compatible)
~XX102 1 7E 30 30 31 30 32 20 31 0D Information Hide On
~XX102 0 7E 30 30 31 30 32 20 30 0D Off (0/2 for backward compatible)
~XX103 1 7E 30 30 31 30 33 20 31 0D Keypad Lock On
~XX103 0 7E 30 30 31 30 33 20 30 0D Off (0/2 for backward compatible)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX104 1 7E 30 30 31 30 34 20 31 0D Background Color Blue
~XX104 2 7E 30 30 31 30 34 20 32 0D Black
~XX104 3 7E 30 30 31 30 34 20 33 0D Red
~XX104 4 7E 30 30 31 30 34 20 34 0D Green
~XX104 5 7E 30 30 31 30 34 20 35 0D White

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX105 1 7E 30 30 31 30 35 20 31 0D Advanced Direct Power On On
~XX105 0 7E 30 30 31 30 35 20 30 0D Off (0/2 for backward compatible)
~XX106 n 7E 30 30 31 30 36 20 a 0D Auto Power Off (min) n = 0 (a=30) ~ 180 (a=31 38 30)
~XX107 n 7E 30 30 31 30 37 20 a 0D Sleep Timer (min) n = 0 (a=30) ~ 995 (a=39 39 39)
~XX115 1 7E 30 30 31 31 35 20 31 0D Quick Resume On
~XX115 0 7E 30 30 31 31 35 20 30 0D Off (0/2 for backward compatible)
~XX114 1 7E 30 30 31 31 34 20 31 0D Power Mode(Standby) Eco.(<=0.5W)
~XX114 0 7E 30 30 31 31 34 20 30 0D Active (0/ 2 for backward compatible)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX109 1 7E 30 30 31 30 39 20 31 0D Lamp Reminder On
~XX109 0 7E 30 30 31 30 39 20 30 0D Off (0/2 for backward compatible)
~XX110 1 7E 30 30 31 31 30 20 31 0D Brightness Mode Brigh t
~XX110 2 7E 30 30 31 31 30 20 32 0D Eco
~XX110 3 7E 30 30 31 31 30 20 33 0D Eco+
~XX111 1 7E 30 30 31 31 31 20 31 0D Lamp Reset Yes
~XX111 0 7E 30 30 31 31 31 20 30 0D No (0/2 for backward compatible)

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX195 0 7E 30 30 31 39 35 20 30 0D Test pattern None
~XX195 1 7E 30 30 31 39 35 20 31 0D Grid
~XX195 2 7E 30 30 31 39 35 20 32 0D White Pattern

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX112 1 7E 30 30 31 31 32 20 31 0D Reset Yes

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX99 1 7E 30 30 39 39 20 31 0D RS232 Alert Reset Reset System Alert
~XX210 n 7E 30 30 32 30 30 20 n 0D Display message on the OSD n: 1-30 characters

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

SEND to emulate Remote

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX140 10 7E 30 30 31 34 30 20 31 30 0D Up
~XX140 11 7E 30 30 31 34 30 20 31 31 0D Left
~XX140 12 7E 30 30 31 34 30 20 31 32 0D Enter (for projection MENU)
~XX140 13 7E 30 30 31 34 30 20 31 33 0D Right
~XX140 14 7E 30 30 31 34 30 20 31 34 0D Down
~XX140 15 7E 30 30 31 34 30 20 31 35 0D Keystone +
~XX140 16 7E 30 30 31 34 30 20 31 36 0D Keystone –
~XX140 17 7E 30 30 31 34 30 20 31 37 0D Volume –
~XX140 18 7E 30 30 31 34 30 20 31 38 0D Volume +
~XX140 19 7E 30 30 31 34 30 20 31 39 0D Brightness
~XX140 20 7E 30 30 31 34 30 20 32 30 0D Menu
~XX140 21 7E 30 30 31 34 30 20 32 31 0D Zoom

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

SEND from projector automatica lly

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

232 ASCII Code HEX Code Function Projector Return Description

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

System status INFOn n : 0/1/2/3/4/6/7/8 = Standby/Warming/Cooling/Ou t of Range/

Lamp fail/Fan Lock/Over Temperature/

Lamp Hours Running Out/Cover Open

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

58

English

Appendices

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

READ from projector (telnet supported)

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

232 ASCII Code HEX Code Function Projector Return Description

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------­~XX121 1 7E 30 30 31 32 31 20 31 0D Input Source OKn n : 0/1/2/3/4/5 = None/VGA1/VGA2/S-Video/ Video/HDMI
~XX122 1 7E 30 30 31 32 32 20 31 0D Software Version OKdddd dddd: FW version
~XX123 1 7E 30 30 31 32 33 20 31 0D Display Mode OKn n : 0/1/2/3/4/5/7/8 = Non e/Presentation/Bright/Movie/sRGB/User/

Blackboard/Classroom/3D
~XX124 1 7E 30 30 31 32 34 20 31 0D Power State OKn n : 0/1 = Off/On
~XX125 1 7E 30 30 31 32 35 20 31 0D Brightness OKn
~XX126 1 7E 30 30 31 32 36 20 31 0D Contrast OKn
~XX127 1 7E 30 30 31 32 37 20 31 0D Aspect Ratio OKn (EW556) n: 0/1/2/3/ 4 = 4:3/16:9 or 16:10 */LBX/Native/AUTO

(ES555/ES556/EX555/EX556) n: 0/1/2/3/4 = 4:3/16:9-I/16:9-II/
Native/AUTO

* 16:9 or 16:10 depend on Screen Type setting
~XX128 1 7E 30 30 31 32 38 20 31 0D Color Temperature OKn n : 0/1/2 = Warm/Medium/Co ld
~XX129 1 7E 30 30 31 32 39 20 31 0D Projection Mode OKn n : 0/1/2/3 = Front-Desktop/Rear- Desktop/Front-Ceiling/

Rear-Ceiling

~XX150 1 7E 30 30 31 35 30 20 31 0D Information OKabbbbccdddde

a : 0/1 = Off/On

bbbb: LampHour

cc: source 00/01/02/03/04/05 = None/VGA1/VGA2/S-Video/

Video/HDMI

dddd: FW version

e : Display mode 0/1/2/3/4/5/6/7/8

None/Presentation/Bright/Movi e/sRGB/User/

Blackboard/Classroom/3D
~XX151 1 7E 30 30 31 35 31 20 31 0D Model name OKn n:1/2/3/4/5 =ES5 55/ES556/EX555/EX556/EW556
~XX108 1 7E 30 30 31 30 38 20 31 0D Lamp Hours OKbbbb bbbb: La mpHour
~XX108 2 7E 30 30 31 30 38 20 31 0D Cumulative Lamp Hours OKbbbbb bbbbb: (5 digits) Total Lamp Hours

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

59

English

Appendices

Please note that

82.30

75.23

55.00

55.00

62.56

64.00

70.80

288.00

220.09

42.77

34.23

70.80

216.20

9.00

damage resulting
from incorrect
installation will void
the warranty.

Warning:

1. If you buy a ceiling
mount from another
company, please

be sure to use the

correct screw size.
Screw size will vary

depending on the

thickness of the
mounting plate.

2. Be sure to keep
at least 10 cm gap
between the ceiling
and the bottom of the

projector.

3. Avoid installing the
projector near a heat
source.

Wall Mount Installation

1. To prevent damage to your projector, please use the
Optoma ceiling mount.

2. If you wish to use a third party ceiling mount kit, please
ensure the screws used to attach a mount to the projector

meet the following specifications:

Screw type: M4*3



Maximum screw length: 11mm



 Minimum screw length: 8mm

Lens

Unit: mm

60

English

Appendices

Optoma Global Ofces

For service or support please contact your local ofce.

USA

3178 Laurelview Ct. 888-289-6786
Fremont, CA 94538, USA 510-897-8601
www.optomausa.com [e-mail]

Canada

2420 Meadowpine Blvd., Suite #105 888-289-6786
Mississauga, ON, L5N 6S2, Canada 510-897-8601
www.optoma.ca [e-mail]

Europe

42 Caxton Way, The Watford Business Park

Watford, Hertfordshire,
WD18 8QZ, UK [phone]

www.optoma.eu [phone]
Service Tel : [phone] [e-mail]

France

Bâtiment E [phone]

81-83 avenue Edouard Vaillant [phone]
92100 Boulogne Billancourt, France [e-mail]

Spain

C/ José Hierro,36 Of. 1C [phone]

28522 Rivas VaciaMadrid, [phone]
Spain

Deutschland

Wiesenstrasse 21 W [phone]
D40549 Düsseldorf, [phone]
Germany [e-mail]

Scandinavia

Lerpeveien 25 [phone]
3040 Drammen [phone]
Norway [e-mail]

PO.BOX 9515

3038 Drammen
Norway

61

English

Appendices

Benelux BV

Randstad 22-123 [phone]
1316 BW Almere [phone]
The Netherlands www.optoma.nl

Latin America

3178 Laurelview Ct. 888-289-6786
Fremont, CA 94538, USA 510-897-8601
www.optomausa.com [e-mail]

Korea

WOOMI TECH.CO.,LTD.

4F,Minu Bldg.33-14, Kangnam-Ku, +82+2+34430004
seoul,135-815, KOREA +82+2+34430005

Japan

東京都足立区綾瀬3-25-18
株式会社オーエス [e-mail]
コンタクトセンター:0120-380-495 www.os-worldwide.com

Taiwan

5F., No. 108, Minchiuan Rd. [phone]
Shindian City, [phone]
Taipei Taiwan 231, R.O.C. [e-mail]
www.optoma.com.tw asia.optoma.com

Hong Kong

Unit A, 27/F Dragon Centre,

79 Wing Hong Street, [phone]
Cheung Sha Wan, [phone]

Kowloon, Hong Kong www.optoma.com.hk

China

5F, No. 1205, Kaixuan Rd., [phone]
Changning District [phone]

Shanghai, 200052, China www.optoma.com.cn

62

English

Appendices

Regulation & Safety Notices

This appendix lists the general notices of your projector.

FCC notice

This device has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential

installation. This device generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications.

However, there is no guarantee that interference will not

occur in a particular installation. If this device does cause

harmful interference to radio or television reception, which can
be determined by turning the device off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the device and receiver.

• Connect the device into an outlet on a circuit different
from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television

technician for help.

Notice: Shielded cables

All connections to other computing devices must be
made using shielded cables to maintain compliance with

FCC regulations.

Caution

Changes or modications not expressly approved by the
manufacturer could void the user’s authority, which is
granted by the Federal Communications Commission, to

operate this projector.

63

English

Appendices

Operation conditions

This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:

1. This device may not cause harmful interference and

2. This device must accept any interference received,

including interference that may cause undesired

operation.

Notice: Canadian users

This Class B digital apparatus complies with Canadian

ICES-003.

Remarque à l’intention des utilisateurs
canadiens

Cet appareil numerique de la classe B est conforme a la
norme

NMB-003 du Canada.

Declaration of Conformity for EU
countries

• EMC Directive 2004/108/EC (including amendments)

• Low Voltage Directive 2006/95/EC

• R & TTE Directive 1999/5/EC (if product has RF function)

Disposal instructions

Do not throw this electronic device into the
trash when discarding. To minimize pollution
and ensure utmost protection of the global
environment, please recycle it.