Optoma BX-CTA16 Installation Guide
A16
US
s
ON
T Len
NSTALLATION INSTRUCTI
Table of Contents
Required accessories and tools ............................................................................................ 3
Entering UST mode for installation setup ............................................................................ 4
Boresight pre-adjustment ....................................................................................................... 4
Installing UST lens boresight module ................................................................................... 5
Installing the lens supporter .................................................................................................. 7
Installing ceiling mount with lens supporter ........................................................................ 9
Installing the UST lens ........................................................................................................... 10
Turning the projector on ........................................................................................................ 11
Image adjustment .................................................................................................................. 11
Lens focus adjustment .......................................................................................................... 11
Boresight adjustment ............................................................................................................. 12
Attaching the lens supporter to the UST lens ..................................................................... 13
Removing the UST lens ......................................................................................................... 13
Change back to the non-UST lens after using the UST lens .............................................. 14
Releasing the UST lens boresight module .......................................................................... 14
Optoma global ofces ............................................................................................................ 17
English2
A16 UST LENS INSTALLATION INSTRUCTION
This user manual is designed to assist with the installation of the BX-CTA16 UST lens in your Optoma projector.
Before attempting to t the UST lens, please read through this document in full order to ensure installation steps
are made correctly.
Required accessories and tools
Check that the following items (A-L) are included in the package. Prepare the required tools to install each item.
Item Image Name of item Quantity
A UST lens 1
B UST lens boresight module 1
C Lens mount bracket 1
D Bracket 1
E Lens supporter 1
F M3 x L8 screws 2
G M3 x L8 hex screws 3
H M6 x L22 hex screws 2
I M3-3.7 x 0.8 x 18 washer 3
J M6-6.7 x 1 x 16 washer 2
K Boresight extender 3
L L shape tool 1
English 3
Entering UST mode for installation setup
To complete the UST lens setup, follow the steps below.
1. Use the hot keys “Exit, Input, Left, Right” on the keypad or Remote control to do UST lens calibration.
2. After UST lens calibration, press “Exit“ to turn off the projector.
3. Disconnect the AC cable.
Boresight pre-adjustment
The UST lens boresight module needs to be adjusted before tting to the projector.
1. Make sure the boresight gears are in the initial state. If not, turn the small boresight gears counterclockwise to the end position, where 2 marks are roughly aligned.
2. Turn the boresight gears clockwise according to the installation orientation.
Note: The ZU850 has a different orientation table from ZU660 and ZU1050.
A
B
ZU850
Orientation A B C
Table top 3+1/4 9 9
Portrait (L)
Portrait (R) 5 + 1/4 10 + 3/4 6
Ceiling mount 10 + 2/4 7 + 1/4 7 + 1/4
Upright 10 + 3/4 8 + 1/4 8 + 2/4
Orientation A B C
Table top 3+1/4 7 + 2/4 8 + 2/4
Portrait (L)
Portrait (R) 5 + 1/4 9 + 2/4 4 + 2/4
Ceiling mount 7 + 1/4 6 6
Upright 7 + 2/4 7 7 + 1/4
6 + 3/4 7 10+3/4
ZU1050 / ZU660 / ZU750 / ZU860
5+1/4 4 10
C
English4
Installing UST lens boresight module
To install UST lens boresight module, complete the following steps.
1. Remove the 3 screws with a Philips #2 screwdriver from the non-UST lens boresight module.
2. Release the non-UST lens boresight module from the projector.
3. Release the lens cable from the original holder on the plate.
English 5
4. Insert the UST lens boresight module to the projector.
5. After installing the UST lens boresight module, fasten the 3 srews with a Philips #2 screwdriver.
6. Insert the cable back into the UST lens boresight module.
Note: Ensure the cable is not wrapped or pinched when fastening the UST lens boresight module.
English6
Loading...