Page 1
English
1
Usage Notice
Precautions .......................................................................................... 2
Introduction
About the Product................................................................................. 3
Package Overview ............................................................................... 4
Installation
Product Overview ................................................................................. 5
Connecting the Projection Display ....................................................... 8
Powering On/Off the Projection Display ............................................... 9
Adjusting the Image Size ...................................................................... 10
User Controls
User Controls ....................................................................................... 12
OSD Menus ......................................................................................... 14
Appendices
Troubleshooting .................................................................................... 18
Maintenance......................................................................................... 20
Specifications ....................................................................................... 23
Compatibility Modes............................................................................. 24
Table of Contents
Page 2
English
2
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user’s manual to maximize the life of your unit.
Do:
q Turn off the product before cleaning.
q Use a soft cloth moistened with mild detergent to clean the display housing.
q Disconnect the power plug from AC outlet if the product is not being used for a
long period of time.
Don’t:
q Block the slots and openings on the unit provided for ventilation.
q Use abrasive cleaners, waxes or solvents for your cleaning.
q Use under the following conditions:
- Extremely hot, cold or humid environment.
- In areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- Place in direct sunlight.
Warning- Do not look into the lens. The bright light may hurt your eyes.
Warning- To reduce the risk of fire or electric shock, do not expose this
product to rain or moisture.
Warning- Please do not open or disassemble the product as this may cause
electric shock.
Warning- When changing the lamp, please allow unit to cool down and follow
all changing instruction.
Warning- This product will detect the life of the lamp itself. Please be sure to
change the lamp when it shows warning messages.
Warning- After changing a new lamp, please reset the lamp life timer from
OSD menu.
Warning- Before switching off the product, please keep the cooling fan
running for a few minutes.
Usage Notice
!
!
!
!
!
!
!
Page 3
English
3
About the Product
This product, designed with a high-powered UHP lamp, is an SVGA data/video
portable projection display. The outstanding feature of it are listed as follows:
q 8.9 lbs. (4.0 kgs) lightweight compact design
q True SV GA, 800 x 600 a ddre ssable pixels
q With XGA compression and VGA resizing
q Mac / NEC PC-98 / FM Towns compatible
q NTSC / PAL / SECAM compatible
q Dual Data Input
q Real plug and play with auto-image function
q User-friendly multilingual on-screen display menu adjustment
q Advanced electronic keystone correction function
q Luxurious carrying case with detachable wheels & handle
Introduction
Page 4
English
4
Package Overview
This projection display comes with all the items shown below. Check to make
sure your unit is complete. Contact your dealer immediately if anything is
missing.
LCD Projection Display
Hard Carrying Case
With Detachable Wheels &
Handle
S-Video Cable RCA Audio/ Video Cable
Audio-in Cable for
Computer
Remote Control
User’s Manual
Warranty Card
Power Cord
VGA Cable X 2
Batteries X 2
Page 5
English
5
Product Overview
w Main Unit
Installation
* There are two elevator releasing buttons and elevator feet on both sides.
* There are also two remote control receivers on the front and the rear side.
Remote Control Receiver
Carrying Handle
Projection Lens
Elevator Foot
Elevator
Releasing Button
Speakers
Panel Controls
Zoom Ring
Focus Ring
Air Filter
Connector Ports
Remote Control
Receiver
Page 6
English
6
ww
ww
w Panel Controls
Computer 1
Input Connector
Power Connector
Computer 2
Input Connector
Monitor Loop-Through
Connector
Audio Output Connector
Audio Input Connector
Audio Input
for Computer
Composite Video
Connector
S-Video
Connector
w Connection Ports
Four Directional
Select Keys
Enter
Page 7
English
7
w Remote Control
Freeze/CLR
Zoom In / Zoom Out
Mute
Keystone
Power/Standby
Source
Volume
Four Directional Select Keys
Menu
Enter
Reset
Resync
Tracking
Page 8
English
8
Connecting the Projection Display
Power Cord
Audio Cable
S-Video Cable
VGA Cable
Audio Cable
Monitor Cable
RCA Audio
Video Cable
Page 9
English
9
uu
uu
u Powering On the Projection Display.
1. Remove the lens cover
2. Plug the power cord into the back of the projector and plug it into the electrical outlet.
The “POWER/STANDBY” LED indicator will flash green.
3. Turn on the lamp by pressing “ POWER/STANDBY” button.
The startup screen displays and starts 30 seconds countdown for lamp .
The “POWER/STANDBY” LED indicator will lit green and stop flashing.
The “LAMP” LED indicator will flash amber for 30 seconds.
4. Make sure the computer or video signal is well connected. The projector will detect
your computer source automatically.
5. If necessary, make adjustments to the image from the projector’s On-Screen Display
(OSD)menus.
Powering On/Off the Projection Display
uu
uu
u Powering Off the Projection Display.
Turn off the lamp by pressing “ POWER/ST ANDBY” button. The confirmation message, ”Power of f
the lamp? ” will show up. Plea se select “Yes” to turn off the lamp. “LAMP” LED indicator will fla sh
amber for about one minute. After the “LAMP” LED indicator stops flashing, you may unplug the
power cord.
Warning:
* When the “LAMP” LED indicator lit amber for a long period of time, please change the lamp
module. Please contact your local dealer or distributor for replacement lamp and refer to “
Changing the lamp”(Page 21) in the manual.
* When the “TEMP” LED indicator lit amber, it indicates the display has been overheated. The
display will automatically shut itself down. While the “TEMP” LED indicator turns “off”, the
display can be switched on again for your presentation.
Page 10
English
10
Adjusting the image size
ww
ww
w
Adjust the height of projected image
Raise the projection display to the desired angle and then press the elevator
release buttons to release the elevator foot.
Fine-tune the height by manually turnig each foot.
Screen
Elevator Foot
Elevator
Releasing Button
(Refer to the following figures below)
Page 11
English
11
ww
ww
w Focus the image
You may a djust zoom ring to zoom in/out 1.3 times of the image size.
To focus the image, rotate the focus ring until the image is clear.
20”
[27”]
[60”]
(20”)
[100”]
(45”)
(76”)
(114”)
[150”]
(153”)
[200”]
[260”]
(197”)
[ ] Maximum
Max.
Screen
(inch)
Distance(ft.)
Min.
27”
20”
3.8’
8.4’ 14’
21’ 28’
36’
60”
45”
100”
76”
150”
114”
200”
153”
260”
197”
Screen Size
60” 100”
150”
200”
260”
16 x 12 49 x 36 80 x 60 120 x 90
160 x 120
208 x 156
(W x H) inch
( ) Minimum
FOCUS
RING
ZOOM
RING
ww
ww
w Adjusting the Image Size
*The graph is for user’s reference only.
Page 12
English
12
User Control Overview
There are two ways for you to control the functions: panel control and remote control.
w Panel Control
w Remote Control
User Controls
Page 13
English
13
Power/Standby
4
Power the lamp on and off when the main power switch is turned on.
Menu
4
Press “Menu” to open the on-screen display (OSD) menus and to switch among different menus.
T o exit OSD, pre ss the “Freeze/CLR” button or select the “ Exit Menu” icon and press “Enter”
button. The projector saves any changes you made automatically.
Source
4
Press “Source” to choose between video and computer sources.
Reset
4
When you press “Reset” button, the OSD menus shows message “Reset All Yes/NO ? ”.
Select “Yes” to confirm or select “ No” to cancel.This function will reset all user
adjustable parameters to factory default settings.
Enter
4
Press “Enter” for confirming your selection.
Four Directional Select Keys
4
Use “Up” or “Down” to select items. Use “Right”or “Left”to make adjustments for your
selection.
4
Use “Up” or “Down” button to change the vertical positioning of the image; and use “Right”or
“Left” button to change the horizontal positioning of the image.
Resync
4
Automatically synchronizes the projector to the input source.
Volume
4
To turn up the volume, press “+” button.
4
To turn down the volume, press “-” button.
4
To mute the volume, press “Mute” button.
Freeze/CLR
4
Press “Freeze/CLR” button to still the screen image.
4
When the OSD displayed, press “Freeze/CLR” button to exit the OSD.
Tracking (Computer mode only)
4
Choose “Tracking” item to synchronize the signal timing of the display with that of the graphic
card. When you experience an unstable or flikering image, use this function to correct it.
Zoom In (Computer mode only)
4
Press “Zoom In” button to enlarge the projected image.
4
When the “Zoom” icon is displayed, you can use four directional select keys to change the
vertical or horizontal positioning of the image.
Zoom Out(Computer mode only)
4
Diminish the zoom in image.
4
When the “Zoom” icon displayed, you can use four directional select keys to change the
vertical or horizontal positioning of the image.
Keystone
4
Adjust image distortion caused by tilting the projector.
Page 14
English
14
4
The Projector has the multilingual On-Screen Display(OSD) menus that allows you
to make image adjustments and change a variety of settings. When in computer
source, the OSD will be the “Computer OSD”. When in Video source, the OSD will
be the “ Video OSD”. The projector will detect the source automatically.
4
To open the OSD menus, press the “Menu” button on the Remote Control or Panel
Control.
4
To select among different menus, press the” Menu” buttn again. Then use “Up”&
“Down” keys to select different items and use “Right” & “Left” to adjust your
selection.
4
To exit the OSD, press the “Freeze/CLR” button or choose the “Exit Menu” and
press “Enter” button.
OSD Menus
4
Brightness
Adjusting the brightness of the image.
l Press the left key to darken the image.
l Press the right key to lighten the image.
4
Contrast
The contrast controls the degree of difference between the lightest and darkest parts of the
picture. Adjusting the contrast to change the amount of black and white in the image.
l Press the left key to decrease the contrast.
l Press the right key to increase the contrast
4
Keystone Correction
Adjusts image distortion caused by tilting the projector.
4
Color T e mperature
Adjusts the color temperture. The range is from 5000°K to 9300 °K . The fa ctory default is 7900°K .
With the higher temperature, the screen looks colder; with the lower temperature, the screen
looks warmer.
How to operate
Language
4
Language
You can display the multilingual OSD . User “ Up” and “ Down” key to select. The menus redrew
immediately.
Display
Page 15
English
15
4
Tracking
Choose “ Tracking “ item to synchronize the signal timing of the display with that of the graphic
card. When you experience an unstable or flickering image, use this function to correct it.
4
Frequency
“Frequency” is for changing the display data frequency to match the frequency of your
computer’s graphic card. When you experience a vertical flickering bar, use this function to make
an adjustment.
4
Auto-Image
The projector automatically adjusts tracking, frequency and vertical and horizontal
position for most computers.
* The image options are available only for computer sources. The projector can set these options
automatically for video sources.
4
Tint (Video mode only)
The tint adjusts the red-green color balance in the projected image.
l Press the left key to increase the amount of green in the image.
l Press the right key to increase the amount of red in the image.
4
Color (V ideo mode only)
The color setting adjusts a video image from black and white to fully saturated color.
l Press the left key to decrease the amount of color in the image.
l Press the right key to increase the amount of color in the image.
Image (Computer mode only)
4
Volume
l Press the left button to decrease the volume.
l Press the right button to increase the volume.
4
Bass
The Bass setting controls the lower frequencies of your audio source.
l Press the left button to decrease the bass.
l Press the right button to increase the bass.
Audio
Page 16
English
16
4
Front-Desktop
The factory default setting.
4
Rear-Desktop
When you select this function, the projector reverses the image so you can project behind a
translucent screen.
4
Front-Ceiling
When you select this function, the projector truns the image upside down for ceiling-mounted
projection.
4
Rear-Ceiling
When you select this function, the projector reverses and truns the image upside down at same time.
You can project from behind a translucent screen with ceiling mounted projection.
4
Treble
The treble setting controls the higer frequencies of your audio source.
l Press the left button to decrease the volume.
l Press the right button to increase the volume
4
Mute
l Choose the left icon to make the volume function ineffective.
l Choose the right icon to make the volume function effective.
4
Mono / Stereo / Stereo-enhance
l Mono: Mono sound effect.
l Stereo: Stereo sound effect.
l Stereo-enhance: Stereo-enhance sound effect.
Projection
416 : 9 (V ideo mode only)
You can select this function to fit your DVD aspect ratio type.
44 : 3 (V ideo mode only)
You can select this function to fit your DVD aspect ratio type.
Page 17
English
17
Lamp
Exit Menu
4
Exit Menu
When you like to close the OSD menus, choose this item and select “ YES” to exit menu.
4
Reset All
Choose “ Yes” to retrun the display parameters of the current mode to its factory default settings.
4
Lamp W arning
Choose this function to show or hide the warning message when the lamp changing warning
message displayed.
4
Lamp Reset
Reset the lamp setting only when the lamp changing is done.
Page 18
English
18
Problem: No image appears on screen.
4
Ensure all the cables and power connections are correctly and securely connected
as described in the “Installation” section.
4
If the projector is plugged into a power strip, make sure the power strip is turned on.
4
Ensure the pins of connectors are not crooked or broken.
4
Check if the projection lamp has been securely installed. Please refer to the “Changing
the lamp” section.
4
Make sure you have removed the lens cap and the projector is switched on.
Problem: Partial, scrolling or incorrectly displayed image.
4Press the “Resync”button on the Remote Control.
4
If you are using a PC:
If the resolution of your computer is higher than 800 x 600. Follow the steps
outlined below to reset the resolution.
For Windows 3.x:
1. In the Windows Program Manager, click the “Windows Setup” icon in the Main
group.
2. V erify that your display resolution setting is less than or equal to 800x 600.
For Windows 95:
1. Open “My Computer” icon, the “Control Panel” folder, and then double click the
“Display” icon.
2. Select the “Setting” tab.
3. In the “Desktop Area” you will find the resolution setting. Verify that the
resolution setting is less than or equal to 800 x 600 resolution.
If the projection display is still not projecting the whole image, you will need
to also change the monitor display you are using. Refer to the following steps.
Troubleshooting
If you are experiencing trouble with the projection display, refer to the following. If the
problem persists, please contact your local dealer or our service center.
Appendices
Page 19
English
19
4
If you are using a Notebook PC:
1. Y ou are required to implement a bove steps of resolution setting of computer first.
2. Switch the Notebook PC display to the “external display only” or “CRT only”
mode.
4
If you are experiencing difficulty in changing resolutions or your monitor freezes,
restart all the equipment and the projection display.
Problem: The screen of the Notebook or PowerBook computer is not displaying
your presentation.
4
If you are using Notebook PC:
Some Notebook PCs may deactivate their own computers’ screens when a
second display device is in use. Each of them has different way to be reactivated.
Refer to your computer’s documentation for detailed information.
4
If you are using an Apple PowerBook:
In Control Panels, open the PowerBook Display to select V ideo Mirroring “On”.
Problem: Image is unstable or flickering
4
Use “Tracking” to correct it.
4
Change the monitor color setting from your computer.
Problem: Image has vertical flickering bar
4
Use “Frequency” to make an adjustment.
4
Check and reconfigure the display mode of your graphic card to make it compatible
with the product.
Problem: Image is out of focus
4
Adjust the Focus Ring on the projector lens.
4
Make sure the projection screen is between the required distance (1.2m - 11m) from the
projector.
4. Follow above steps 1~2. Click on the “Advanced Properties ” button.
5. Select the “Change” button under the “Monitor” tab .
6. Click on “ Show all devices ”. Then select “ Standard monitor types ” under the
“ Manufactures ” box; choose the resolution mode you need under the “ Models”
box.
7. V erify that the resolution setting of the monitor display is le ss than or equal to
800 x 600.
Page 20
English
20
Problem : The screen is outstretched when displaying 16:9 DVD.
The projector itself will automatically detect 16:9 DVD and adjust the aspect ratio by
digitization to full screen with 4:3 default setting.
If the projection display is still outstretched, you will also need to a djust the aspect ratio
by referring to the following:
4 Please select 4:3 aspect ratio type on your DVD player if you are playing a 16:9 DVD.
4 If you can not select 4:3 aspect ratio type on your DVD player, please select 4:3 On-
Screen-Display(OSD) function of the projector for your display.
Page 21
English
21
Maintenance
ww
ww
w Cleaning the A ir Filter
4
Cleaning Procedure:
1. Turn off the power.
2. Remove the air filter cover.
3. Remove the air filter from the filter cover.
4. Clean the air filter with a vacuum cleaner.
5. Place the air filter back in position. Make sure the air filter is fully inserted.
Do not clean the filter with water. Doing so may damage the air filter.
Do not operate the projection display with air filter removed.
!
Air Filter
Air Filter Cover
Air Filter
Page 22
English
22
w Changing the lamp
The projection display will detect the lamp life itself. It will show you a warning
message when the lamp is used over working hours. When you see this message,
change the lamp as soon as possible.
Make sure the projection display has been cooled for at least 60 minutes before
changing the lamp.
Warning: Lamp compartment is hot! Allow it to cool before changing
lamps!
4
Lamp Changing Procedure:
1. Turn off the power and allow the projection display to cool down.
2. Disconnect the power cord.
3. Unscrew the 2 screws of the lamp cover and remove the cover.
Lamp Cover
Screws
Lamp Cover
!
Page 23
English
23
5. Replace the new lamp module by the handle and tighten the screws.
4. Unscrew the 2 screws of the lamp module and pull out the lamp module by the
handle.
6. Place the lamp cover back in position and lock the 2 screws.
7. Remember to reset the lamp life timer from OSD menus.
Lamp Handle
Lamp Screws
Lamp Handle
Page 24
English
24
Specifications
LCD panel - active matrix TFT color LCD
- 0.9” poly-silicon panels x 3
- tr=12ms, tf=30ms response time
- 350:1 contrast ratio
Lamp - 150-watt UHP lamp
Number of Pixels - 800 pixels (H) X 600 lines (V)
Displayable Color - 16.7M colors
Projection Lens - F1.8 ~2.0, f 38~50mm w/ 1.3 X zoom & focus
Image Size - adjustable 20” to 260”
Projection Distance - 3.8 ft. to 36 ft. / 1.2 m to 11 m
Computer Compatibility - VESA VGA 640 x 350, 70/85Hz
- VESA VGA 640 x 480, 60/72/75/85Hz
- VESA VGA 720 x 400, 70/85Hz
- VESA SVGA 800 x 600, 56/60/72/75/85Hz
- XGA 1024 x 768 Compressed ,
60/70/75/85Hz
- Apple Macintosh LC 13” 640 x 480, 67Hz
- Apple Macintosh II 13” 640 x 480, 67Hz
- Apple Macintosh 16” 832 x 624, 75Hz
- Apple Macintosh 19” 1024 x 768, 75Hz Compressed
- NEC PC-98 series 640 x 400, 57Hz
640 x 480, 60/70Hz
- FM TO WNS 640 x 480, 55/60 Hz
Video Compatibility - NTSC / PAL / SECAM compatible
- composite video & s-video capability
H. Frequency - 15kHz~69kHz horizontal scan
V. Frequency - 50Hz~85Hz vertical refresh
Multimedia Audio - internal speakers with 3 watt x 1 output
- built-in amplifier with 3 watt x 1 output
Power Supply - auto switch
- input AC 100-240V, 50-60Hz
I/O Connectors - power: AC power input socket
- computer input: HDB 15-pin female connector x 2
- computer output: HDB 15-pin female connector
- video input: composite video RCA jack x 1 / S-Video jack x 1
- audio input: 2 pairs of L/R RCA jacks
- audio output: 1 pair of L/R RCA jacks
Weight - 8.9 Ibs / 4.0 kgs
Dimensions (W x H x D) - 8.8 x 4.3 x 14.1” / 224 x 109 x 359 mm
Environmental - operating temperature: 10o~35oC/50o~104oF
humidity: 80% maximum
storage temperature: -20o~60oC/ -4o~140oF
humidity: 80% maximum
Safety Regulation - FCC, CE, VCCI,BSMI, UL, CUL, TUV
Page 25
English
25
Compatibility Modes
*: Compressed
AGVASEV&MBI053x0465.1307
AGVASEV&MBI053x0469.7358
AGVASEV&MBI084x0465.1307
AGVASEV&MBI084x0469.7358
AGVASEV&MBI004x0275.1307
AGVASEV&MBI004x0279.7358
AGVASEV&MBI084x0465.1306
AGVASEV&MBI084x0469.7327
AGVASEV&MBI084x0465.7357
AGVASEV&MBI084x0463.3458
AGVSASEV006x0082.5365
AGVSASEV006x0089.7306
AGVSASEV006x0081.8427
AGVSASEV006x0089.6457
AGVSASEV006x0087.3558
AGXASEV*867x42014.8406
AGXASEV*867x42015.6507
AGXASEV*867x42010657
AGXASEV*867x42019.8658
"31CLhsotnicaMelppA084x04689.4366.66
"31IIhsotnicaMelppA084x04600.5386.66
"61hsotnicaMelppA426x23827.9455.47
"91hsotnicaMelppA*867x420142.0657
89CP004x04638.4224.65
89CP084x0465.1307
89CP084x0465.1306
snwoTMF084x04673.4273.55
snwoTMF084x0465.1306
Mode
Resolution
H.Frequency
(kHz)
V.Frequency
(Hz)
Loading...