OPTOELECTRONICS OPN3102N Users Manual

O

a

D

a

SPECIF

I

e

f

M

h

f

o

m

0

t

N

n

n

CATIONS

ANUAL

O

PN-3102n

1st

N

ata Coll

-3

ctor wit

1

Bluetoo

2

h

1st

This m

nual prov

dat

ides speci

collector

ications f

with 2D i

r the OP
ager sca

-3102n Bl

ner.

uetooth

1

SPECIFICATIONS MANUAL

OPN-3102n

1st

The information in this document is subject to change without notice.

Document History

Model Number: OPN-3102n Specification Number: SS16059
Edition: 1st Original Spec Number: (SS16054)
Date: 30-September-2016

2016 Copyright Opticon. All rights reserved.

This manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted
to any electronic or machine readable form without prior written consent of Opticon.

Limited Warranty and Disclaimers
PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING

OR USING THE PRODUCT.
Serial Number

A serial number appears on all Opticon products. This official registration number is directly related to
the device purchased. Do not remove the serial number from your Opticon device. Removing the
serial number voids the warranty.

Warranty

Unless otherwise agreed in a written contract, all Opticon products are warranted against defects in
materials and workmanship for two years after purchase excluding batteries. Opticon will repair or, at
its option, replace products that are defective in materials or workmanship with proper use during the
warranty period. Opticon is not liable for damages caused by modifications made by a customer. In
such cases, standard repair charges will apply. If a product is returned under warranty and no defect is
found, standard repair charges will apply. Opticon assumes no liability for any direct, indirect,
consequential or incidental damages arising out of use or inability to use both the hardware and
software, even if Opticon has been informed about the possibility of such damages.

Packaging

The packing materials are recyclable. We recommend that you save all packing material to use should
you need to transport your data collector or send it for service. Damage caused by improper
packaging during shipment is not covered by the warranty.

Trademarks

Trademarks used are the property of their respective owners.

Opticon Inc. and Opticon Sensors Europe B.V. are wholly owned subsidiaries of
OPTOELECTRONICS Co., Ltd., 12-17, Tsukagoshi 4-chome, Warabi-shi, Saitama, Japan 335-0002.
TEL [phone]; FAX [phone]

SUPPORT

USA Europe

Phone: [phone]
Email: [email protected] Email: [email protected]
Web: www.opticonusa.com Web: www.opticon.com

2

SPECIFICATIONS MANUAL

Revision History

Product Name : OPN-3102n

Edition Date Page Section Description of Changes

1st 2016/09/30 - -

OPN-3102n

1st

3

SPECIFICATIONS MANUAL

OPN-3102n

1st

Contents

1 Abstract ............................................................................................................................ 6

2 Overview .......................................................................................................................... 6

3 Basic Specifications ....................................................................................................... 7

4 Detailed View ................................................................................................................. 10

5 Electrical Specifications ............................................................................................... 11

5.1 USB ........................................................................................................................................ 11

5.2 Wireless Charging .................................................................................................................. 11

6 Interface Specifications ................................................................................................ 11

6.1 USB Interface ......................................................................................................................... 11

6.1.1 Connector ....................................................................................................................... 11

6.1.2 USB Interface Circuit ...................................................................................................... 11

6.2 Bluetooth ................................................................................................................................ 12

6.3 NFC Tag ................................................................................................................................. 12

7 Optical Specifications ................................................................................................... 13

7.1 Basic Specifications ............................................................................................................... 13

7.2 Aiming Pattern ........................................................................................................................ 14

8 Technical Specifications .............................................................................................. 15

8.1 Barcode Test Sample ............................................................................................................. 16

8.2 Scan Area and Depth of Field ................................................................................................ 17

8.3 Printed Contrast Signal (PCS) ............................................................................................... 19

8.4 Minimum Resolution ............................................................................................................... 19

8.5 Barcode Width ........................................................................................................................ 19

8.6 Pitch, Skew and Tilt ................................................................................................................ 20

8.7 Curvature ................................................................................................................................ 20

8.8 Scanning from LCD Screen.................................................................................................... 21

8.9 Motion Tolerance .................................................................................................................... 21

9 Environmental Specifications ...................................................................................... 22

9.1 Temperature ........................................................................................................................... 22

9.2 Humidity .................................................................................................................................. 22

9.3 Ambient Light Immunity .......................................................................................................... 22

9.4 Dust and Drip Proof ................................................................................................................ 22

9.5 Vibration Strength (without packing) ...................................................................................... 23

9.6 Vibration Strength (in individual packing) ............................................................................... 23

9.7 Drop Impact Strength (without packaging) ............................................................................. 23

9.8 Drop Impact Strength (in individual packaging) ..................................................................... 23

9.9 Electrostatic Discharge Immunity ........................................................................................... 23

10 Regulatory Compliance ................................................................................................ 24

10.1 LED Safety ............................................................................................................................. 24

10.2 Product Safety ........................................................................................................................ 24

10.3 EMC ........................................................................................................................................ 24

4

SPECIFICATIONS MANUAL

OPN-3102n

1st

10.4 Other ....................................................................................................................................... 25

11 RoHS .............................................................................................................................. 25

12 Reliability ....................................................................................................................... 25

13 Precautions .................................................................................................................... 25

13.1 Radio Law............................................................................................................................... 26

13.2 Bluetooth ................................................................................................................................ 26

13.3 Frequency Band ..................................................................................................................... 26

14 Product Labels .............................................................................................................. 27

15 Packaging Specifications ............................................................................................. 28

15.1 Individual Packaging .............................................................................................................. 28

15.2 Collective Packaging .............................................................................................................. 29

16 Physical Features .......................................................................................................... 30

16.1 Dimensions ............................................................................................................................. 30

16.2 Weight .................................................................................................................................... 30

16.3 Mechanical Drawing ............................................................................................................... 30

17 Supported Symbologies ............................................................................................... 31

17.1 Default Setting ........................................................................................................................ 31

17.2 Supported Symbologies ......................................................................................................... 31

17.2.1 1D Barcodes ................................................................................................................... 31

17.2.2 GS1 Databar, Composite Code ...................................................................................... 32

17.2.3 2D Codes ........................................................................................................................ 32

Table of Figures

Figure 1: Detailed View ......................................................................................................................... 10

Figure 2: micro USB B Connector ......................................................................................................... 11

Figure 3: Interface Circuit (USB) ........................................................................................................... 11

Figure 4: Aiming Pattern and Imaging Range ....................................................................................... 14

Figure 5: Scanning conditions ............................................................................................................... 15

Figure 6: Scan Area and Depth of Field ................................................................................................ 18

Figure 7: Wide Barcode ......................................................................................................................... 19

Figure 8: Pitch, Skew and Tilt ................................................................................................................ 20

Figure 9: Curvature ................................................................................................................................ 20

Figure 10: Motion Tolerance.................................................................................................................. 21

Figure 11: Drop Test .............................................................................................................................. 23

Figure 12: Product Label Position ......................................................................................................... 27

Figure 13: Individual Packaging ............................................................................................................ 28

Figure 14: Collective Packaging ............................................................................................................ 29

Figure 15: Mechanical Drawing ............................................................................................................. 30

5

SPECIFICATIONS MANUAL

OPN-3102n

1 Abstract

This manual provides specifications for the OPN-3102n compact 2D data collector with built-in
Bluetooth.

2 Overview

The OPN-3102n is 2D imager scanner built-in and output scanned barcode data using the Bluetooth
interface.

・OPN-3102n is handy and simple data collector.

・All barcode data scanned is transmitted to a host device through the USB interface or

Bluetooth.

・The scanner can work with many Bluetooth-enabled host devices, such as PCs, tablet PCs

and smart phones.

・Bluetooth SPP (Serial Port Profile) and HID (Human Interface Device Profile) are

implemented.

・Built-in NFC tag facilitate the Bluetooth connection
・The scanner can read barcodes from LCD screens.

・A green LED aiming line toward a target barcode can help the users find the appropriate

scanning position.

・Alcohol can be used to wipe the scanner clean
・The power source is 3.7 V 600 mAh (typ.) Li-ion polymer battery.
・The charging is done through a dedicated charging cradle CRD-3000 or USB interface.

1st

6

SPECIFICATIONS MANUAL

3 Basic Specifications

Item Specification Note

CPU 32 bit CISC / 96 MHz

Section

Control

FROM 512 Kbyte + 32 Kbyte

OPN-3102n

1st

SRAM 96 Kbyte

FROM (storage) 1 Mbyte

Section

Input

Key type 2 key: trigger, function

Indicator

LED 2 bi-colors LEDs (red, green) and 1 blue LED

Buzzer Loudness (3-level) / tone adjustable

Vibration motor Strength (3-level) / duration adjustable

RTC

Contents Year, month, date, hour, minute, second

Accuracy ± 90 seconds per month

Frequency 2402 ~ 2480 MHz

Specification Bluetooth Ver 2.1 compliant

Bluetooth

Interface

Communication
distance

10 m

Output level Class 2

Profile SPP / HID

NFC tag

USB

Scanning method VGA CMOS area sensor

Optical Section

ISO/IEC 14443 TYPE A, TYPE B
JISX6319-4

・Full-Speed 12Mbps ( HID/COM )
・Hi-Power Bus-powered supported

Scanning light source 1 Warm-White LED

For data area only

Data and time are lost
when the main battery
is removed.

Not guaranteed.

Max output 4 dBm

Aiming light source 1 green LED

Effective pixels 0.30 million pixels

View angle

Horizontal: about 38.0°
Vertical: about 26.4°

UPC-A, UPC-A Add-on, UPC-E,
UPC-E Add-on, EAN-13, EAN-13 Add-on, EAN-8,

Supported 1D Symbologies

EAN-8 Add-on, JAN-8, JAN-13, Code 39, Tri-Optic,
NW-7, Industrial 2 of 5,

Symbologies

Interleaved 2 of 5, S-Code, IATA, Code 93,
Code 128, MSI/Plessey, UK/Plessey, TELEPEN,
Matrix 2 of 5, Chinese Post Matrix 2 of 5,
Code 11, Korean Postal Authority code, Postal
Code

Minimum resolution Code 39 : 0.1 mm

Curvature

Barcode width

R ≥ 16 mm (10-digit Codabar 0.15mm)
R ≥ 20 mm (12-digit UPC)

100 mm wide 0.2 mm resolution Code 39 (DOF 150
mm) is readable:

Refer to Chapter 17.
for details

PCS 0.9

PCS 0.9

7

Item Specification Note

Motion Tolerance

SPECIFICATIONS MANUAL

UPC 100% moving at 2m/sec (DOF 100 mm)
is readable:

Resolution (0.127) 90 ~ 110

OPN-3102n

1st

Depth of Field

GS1/Composite

Symbologies

Minimum resolution

Symbologies

Supported 2D Symbologies

Minimum resolution (mm)

Depth of
field
(mm)

Code 39

Resolution (0.254) 65 ~ 185

Resolution (0.508) 65 ~ 260

Code 128 Resolution (0.2) 85 ~ 165

UPC Resolution (0.33) 55 ~ 195

GS1 DataBar , GS1 DataBar Limited,
GS1 DataBar Expanded,
Composite GS1 DataBar, Composite GS1-128,
Composite EAN, Composite UPC
GS1 DataBar : 0.127mm
Composite Code: 0.127 mm
PDF417 , MicroPDF417 , Codablock F ,
QR Code , MicroQR Code ,
Data Matrix ( ECC 0 - 140 / ECC 200 ) ,
MaxiCode( Modes 2 to 5 ) , Aztec Code ,
Chinese-sensible code
PDF417 : 0.169 mm
QR Code : 0.169 mm
DataMatrix : 0.169 mm

Resolution (0.169) 85~ 135

PDF417

Resolution (0.254) 65 ~ 180

Resolution (0.212) 90 ~ 110

QR Code

Resolution (0.381) 55 ~ 180

GS1 DataBar:
formerly called
“RSS”

Disable Code 128
when Codablock F is
enabled.

PCS 0.9

PCS 0.9
TBD

DataMatrix Resolution (0.254) 85 ~ 135

Pitch : ±70°

Scan angle

Common

Skew : ±70°

Tilt : ±360°

Minimum PCS 0.2 or more

White brightness 30 cd/m2 or more

Scanning from LCD screen

Contrast ratio 100:1 or more

Main battery Lithium-polymer 600 mAh (typ.)

Power Section

Up-time 10 hours or more

Feeding system

Electromagnetic guidance wireless charging,
microUSB

Operating (charging) voltage 4.5 ~ 5.5V

Current
consumption

Charging Less than 500 mA

Operating -10 ~ 50°C

Temperature

Environmental

Specifications

Storage -20 ~ 60°C

Operating 20 ~ 85%

Humidity

Storage 20 ~ 85%

MRD 32% or more

*1

Charging with USB

No condensing
No frost

Ambient light
immunity

Fluorescent 10,000 lx or less

Sunlight 100,000 lx or less

8

SPECIFICATIONS MANUAL

2

Item Specification Note

10 Hz ~ 100 Hz, acceleration of 19.6 m/s

Vibration

Drop

Dust and drip proof IP54 equivalent

LED safety IEC 62471:2006 Exempt_Group

Product safety

Regulatory Compliance

EMC

European conformity

minutes per cycle, repeat once in each X, Y and Z­direction
Drop the scanner 18 times (6 faces x 3) from a
height of 150 cm onto a concrete floor

EN60950-1:2005
IEC60950-1:2006
EN 55024:2010
EN 55032:2012+AC :2013
EN 301 489-1 V1.9.2
EN 301 489-17 V2.1.1
EN 300 328 V1.9.1
EN 302 291-2 V1.1.1
FCC Part 15 Subpart C, Subpart B ClassB
VCCI Class B

CE Marking

Certification for Construction Design of Specified
Radio Equipment

OPN-3102n

1st

, 60

Peak Wavelength：
624 nm

For residential,
commercial and light­industrial
environments

Other Bluetooth logo certification

Immunity

Test

ESD

Features

Physical

Dimensions 83.0 × 36 × 21.5 (WDH mm)

Weight Approx. 60 g

No
distraction
No
malfunction

Air discharge (direct): ±15 kV

Air discharge (direct): ±8 kV

Conditions:
IEC61000-4-2
compliant

Excluding accessories

*1: When a barcode is read twice every 10 seconds at room temperature in a constant Bluetooth connection (SPP
master mode).

9

4 Detailed View

SPECIFICATIONS MANUAL

OPN-3102n

1st

1

5

8

9

6

7

Figure 1: Detailed View

No Name Description

3

4

2

1 Scan Window LED illumination is emitted from this window to read barcodes.

2 USB Cap Cap for USB connector part used to make the scanner IP54 water tight.

3 Trigger Key Press this key to enable the laser and start reading barcodes.

4 Function Key The function of this key depends on the installed application.

5 LED

6 Buzzer Orifice Holes for buzzer.

7 Strap Orifice Holes for attaching a hand strap.

8 Charging Coil

9 NFC

Indicates operating status, such as bar code reading, Bluetooth
connection, warning etc.

The charging coil is located here with which the dedicated cradle can
supply power to the scanner.

This is the location of the NFC tag. Hold an NFC reader close to this
area when the tag has to be read.

10

5 El

e

uBuCu

W

ePo

t

N

C

S

l

u

m

S

p

a

u

r

N

A

A(NC

a

a

a

p

C

t

w

p

I

V

m

a

m

a

a

m

M

w

u

n

c

h

u

S

t

t

ctrical

pecific

SPECIF

tions

CATIONS

ANUAL

O

PN-3102n

1st

5.1 U

S

5.2

F

6 In

The OP

6.1 U

In

6.1.1

SB

pply Voltag
s-power (C
rrent cons

ireless C

eding syste
wer consu

erface

-3102n su

SB Interf

terface is F

onnecto

Signal

VC

DAT

DAT

GN

e

ass)
mption

harging

m

ption

pecific

ports two ty

ce

ll Speed US

ame

C

(-)

(+)

)

D

: 4.5-5.5
: 500mA
: Less th

: Electro
: Less th

tions

es of interf

B interface.

ontact Nu

1

2

3

4

5

ax (Hi-Po

n 500mA

agnetic ind

n 5W

ces; USB a

ber

er)

ction

d Bluetoot

.

Fig

re 2: micro U

B B Connec

or

6.1.2

USB Interf

ce Circui

Po
Su

Micro­controller

er

ly

Figure 3:

Interface Cir

uit (USB)

USB Connec

tor

11

SPECIFICATIONS MANUAL

t

t

6.2 Bluetooth

The specifications of the OPN-3102n Bluetooth interface are as follows:
Frequency : 2402 ~ 2480 MHz

Specification : Bluetooth Ver 2.1 compliant

Communication distance : 10 m

Output level : Class 2 (max 4 dBm)

Implemented profile : SPP / HID

Communication configuration : 1 to 1

Operating mode in communication : Master / Slave mode

Security mode : Authentication supported

Encryption : Encryption supported

6.3 NFC Tag

OPN-3102n has NFC tag built-in which record Bluetooth device address.
Frequency: 13.56MHz

Standard : ISO/IEC 14443 TYPE A, TYPE B and JISX6319-4
Recorded Contents: :

Rewriting from external: possible

Total 928 byte

NDEF

Record #1

ype: ”application/vnd.bluetooth.ep.oob”
OOB data length: 8 Byte
MAC address: 00:12:6A:xx:xx:xx

Record #2

ype: ”T”
TEXT data length: 15 Byte
TEXT data: ”00126Axxxxxx”

Free area

Reserved area

*xx will differ according to product.

OPN-3102n

1st

12

SPECIFICATIONS MANUAL

7 Optical Specifications

7.1 Basic Specifications

Item Characteristics

Scan method CMOS area sensor (white / black) -

Number of effective pixel (Column) × (Row) 640 × 480 dots

Image capture speed (*1) Frame rate 100 fps

Focal distance Distance from the front edge of scanner 109.2 mm

View angle

Diagonal Approx. 46.4°

Illumination light source
(LED × 1)

Aiming light source
(LED × 1)

*1 The fastest seed of image capture
*2 Reference value extracted from the LED datasheet.

Horizontal Approx. 38.0°

Vertical Approx. 28.9°

Color Warm white

Color temperature

Radiant efficiency(*2) 114lm/W

Color Green

Peak wavelength 535 nm

Radiant efficiency (*2) 114lm/W

OPN-3102n

1st

2600～3700K

13

A

T12 T--

t

s

o

s

n

n

a

s

h

h

g

s

4

i

SPECIF

I

p

a

o

4

M

a

w

g

c

d

a

2

n

n

e

CATIONS

ANUAL

O

PN-3102n

1st

7.2

iming Pa

he aiming i
. Fill light t
. Fill light w

he aiming

The horizo

a distance

The horizo

horizontal

tern

used for t

recognize t

hen auto tri

pecification

tal width of

of L=144.2±

tal imaging
iming width

e following

e appropri

ger is used.

are as foll

the imaging

0 mm from

field of view

.

urpose:

te reading r

ws:
field of vie

the front ed

at a distan

nge.

and the hor

e of the sc

e of L=144.

zontal aimi
nner.
mm is 0%±

g width are

10% of the

qual at

F

gure 4: Aimin

g Pattern an

Imaging Ra

ge

14

SPECIFICATIONS MANUAL

OPN-3102n

8 Technical Specifications

Aim the laser light at the center of a code to scan it. The conditions for technical specifications are as
follows, unless otherwise specified in each section.

<Conditions>
Ambient Temperature and Humidity Room temperature, room humidity

Ambient Light 100 ~200 lux (on the surface of a barcode)
Angles Pitch: α = 0°, Skew: β = 15°, Tilt: γ = 0°
Curvature R = ∞
Power Supply Voltage 5.0 V (USB)
PCS (1D and 2D) 0.9 or higher

Scanning Test Accept the performance with 90% or more success rate

for 10 tries of scan. One reading should be 2 seconds.

Barcode Test Sample (1D and 2D)

< Test chart >
For 1D codes, OPTOELECTRONICS test samples
For GS1 Databar, stacked codes and 2D codes, printed by a dedicated printer for barcode

Specified below.

1st

-

-

β

+

Figure 5: Scanning conditions

+

-

Center of image

γ

+

15

SPECIFICATIONS MANUAL

8.1 Barcode Test Sample

1D Barcodes

<Code 39>

Resolution Symbology PCS Size (mm) No. of Digits

0.1 mm (3.9 mil)

0.127 mm (5 mil) 32 × 10 15

0.20 mm (7.9 mil) 100 × 10 31

0.254 mm (10 mil) 32.5 × 12 7

0.508 mm (20 mil) 36 × 25 4

<Code 128>

Resolution Symbology PCS Size (mm) No. of Digits

0.20 mm (7.9 mil) Code 128 0.9 42 × 10 16

<UPC>

Resolution Symbology PCS Size (mm) No. of Digits

0.330 mm (13 mil)

<Codabar>

Resolution Symbology PCS Size (mm) No. of Digits

0.150 mm (6 mil) Codabar(NW-7) 0.9 20 × 10 10

GS1 Databar/Composite

<GS1-limited>

Resolution Symbology PCS Size (mm) No. of Digits

0.169 mm (6.7 mil) Limited 0.9 12 × 1.5 14

0.169 mm (6.7 mil) Limited-Composite 0.9 12 × 3.0 26

2D Codes

<PDF417>

Resolution Error Correction PCS Size (mm)

0.169 mm (6.7 mil)

0.254 mm (10 mil) 35 × 15

<QR Code: Model-2>

Resolution Error Correction PCS Size (mm)

0.212 mm (8.4 mil)

0.381 mm (15 mil) 11 × 11

<Data Matrix>

Resolution Model PCS Size (mm)

0.212 mm (8.4 mil)

0.254 mm (10 mil) 6 × 6

* The size is outline dimensions excluding the quiet zones.

Code 39 0.9

12-digit UPC
12-digit EAN

0.9/0.2 31.5 × 25.0 12/13

Level-3 0.9

M 0.9

ECC200 0.9

OPN-3102n

8.5 × 10 4

No. of Character

23 × 10

5 × 5

58

No. of Character

44

No. of Character

4 × 4

40

1st

16

SPECIFICATIONS MANUAL

8.2 Scan Area and Depth of Field

The scanner is able to read in the area between the two arcs that are centered on the scan
origin with a center line distance from the front of the scanner as indicated for each resolution.

Symbology Resolution

Code 39 0.127mm

0.254mm

0.508mm
Code 128 0.20mm
UPC 0.33mm
PDF417 0.169mm

0.254mm
QR Code 0.169mm

0.381mm
Data Matrix 0.212mm

0.254mm

<Conditions>

Barcode Sample The above codes specified in Chapter 8.1

Angle

α = 0°, β =＋15°, γ = 0°

Depth of Field (mm)

60 ～ 105
70 ～ 205
80 ～ 390
80 ～ 165
65 ～ 260
65 ～ 125
50 ～ 180

70 ～ 95
35 ～ 225
60 ～ 130
50 ～ 150

OPN-3102n

1st

17

[ inch ]

[ mm ]

SPECIFICATIONS MANUAL

OPN-3102n

1st

2" 4"

0

50 100 150 200 250 300

6"

8"

10" 12"

14"

350

16"0"

400

17"

450

Code 39

Code 128

100%
EAN/UPC

0.127mm ( 5mil )

0.20mm ( 7.9mil )

0.254mm ( 10mil )

0.33mm( 13mil )

0.508mm ( 20mil )

75

25

050

25

50

75

100 100 125 150125150

[ inch ]

[ mm ]

3"

1"

0" 2"

1"

2"

3"

4" 4" 5" 6"5"6"

0.169mm( 10mil )

PDF417

0.254mm( 10mil )

0.169mm( 6.7mil )

QR Code

Data Matrix

0.381mm( 15mil )

0.212mm( 8.4mil )

0.254mm( 10mil )

Figure 6: Scan Area and Depth of Field

18

SPECIFICATIONS MANUAL

8.3 Printed Contrast Signal (PCS)

0.2 or higher

<Conditions>
MRD : 10% and higher

(70% or higher reflectivity of space and quiet zone)
Distance : 125mm from the front edge of the scanner
Barcode Sample : UPC specified in Chapter 8. (Resolution: 0.33 mm, PCS: 0.3)

MRD = Minimum reflectance of white bar - Maximum reflectance of black bar

* Be sure to keep the optical window clean without dirt or scratches, or it may have a detrimental effect on
the reading characteristics.

PCS =

Reflectance of white space – Reflectance of black bar

Reflectance of white space

8.4 Minimum Resolution

1D Code : 0.1 mm (3.9 mil) Code 39 specified in Chapter 8.1
GS1-Databar : 0.127 mm (5 mil) GS1 Databar Limited specified in Chapter 8.1
Stacked Code : 0.169 mm (6.7 mil) PDF417, GS1 Databar Limited Composite specified in Chapter 8.1
2D Code : 0.169 mm (6.7 mil) QR Code, Data Matrix specified in Chapter 8.1

<Conditions>

Barcode Sample The above codes specified in Chapter 8.1
Distance 95 mm from the front edge of the scanner

Angle

Curvature R = ∞

α = 0°, β =＋15°, γ = 0°

OPN-3102n

1st

8.5 Barcode Width

Code 39 with width of 100 mm and resolution of 0.2 mm can be read

<Conditions>

Barcode Sample 0.20 mm Code 39 / PCS 0.9 specified in Chapter 8.1
Distance 150 mm from the front edge of the scanner

Angle

Curvature R = ∞

α = 0°, β =＋15°, γ = 0°

Figure 7: Wide Barcode

19

8.6 Pitch, Skew and Tilt

Pitch : α = ±70°
Skew : β = ±70°
Tilt : γ = ±360°

<Conditions>

Barcode Sample : 0.33 mm UPC specified in Chapter 8.1
Distance : 125 mm from the front edge of the scanner
Curvature : R = ∞
* For the pitch angle and tilt angle measurement, set the skew angle β = +15°

SPECIFICATIONS MANUAL

OPN-3102n

1st

-

β

+

Figure 8: Pitch, Skew and Tilt

8.7 Curvature

0.33 mm 12-digit UPC: R ≧ 20 mm

0.15 mm 10-digit Codabar(NW-7): R ≧ 16 mm

<Conditions>

Barcode Sample 0.33 mm UPC, 0.15 mm Codabar specified in Chapter 8.1
Distance 105 mm from the edge of the scan engine
Angle Skew angle β = +15°

バーコード

Barcode

-

+

-

γ

+

R

Figure 9: Curvature

Note:
The reading performance may deteriorate if there is specular reflection of the laser light, this typically will occur
when the reflectivity of the barcode is high.

20

SPECIFICATIONS MANUAL

8.8 Scanning from LCD Screen

Barcodes displayed on LCD screens (brightness of white part 30 cd/m2 or more, contrast ratio
100:1 or more) can be read.

<Conditions>

Barcode : UPC, resolution 0.33 mm specified in Chapter 8.1.
Ambient light : 100 lx or less
Distance : 95 mm from the front edge of the scanner
Angle : α = 0°, β = 0°, γ = 0°
LCD screen type : Transmissive (backlight) TFT
Illumination mode : Disable

Contrast ratio =

* The barcode resolution is the value when displayed on the LCD screen.
* The width of barcode element is an integral multiple of pixel width of LCD screen.
* The reading characteristics may deteriorate due to the specular reflection of LED illumination

when the reflectivity is high.

Brightness of white parts
Brightness of black parts

OPN-3102n

1st

8.9 Motion Tolerance

UPC 100%/EAN can be read when it is moving at 2.54m/s.

<Conditions>

Ambient Temperature and Humidity : Room temperature and Room humidity
Ambient Light : 500 ~ 1000 lux
Distance : 125 mm from the front edge of the scanner
PCS (1D and 2D) : 0.9 or higher
Barcode Sample : UPC 0.33mm specified in Chapter 8.1.

* Scanning may fail due to the specular reflection of LED illumination when the reflectivity is high.

Figure 10: Motion Tolerance

21

SPECIFICATIONS MANUAL

9 Environmental Specifications

9.1 Temperature

Scanning performance is guaranteed when the ambient temp. is within the following range:

Operating Temperature: -10 ~ 50
Storage Temperature: -20 ~ 60

* Please charge when the temperature is between 0 and 40°C. When the temperature is over 40°C,
charging may stop to prevent battery breakdown.

9.2 Humidity

Scanning performance is guaranteed when the ambient humidity within following range:

Operating Humidity: 20 ~ 85%RH (no condensation, no frost)
Storage Humidity: 20 ~ 85%RH (no condensation, no frost)

9.3 Ambient Light Immunity

Scanning performance is guaranteed when the illumination on a barcode surface is between
zero and the following values:

Incandescent light: 10,000 lx
Fluorescent light: 10,000 lx
Sunlight: 100,000 lx

<Conditions>

Barcode: 0.33 mm JAN specified in Chapter 8.1.
Distance: 95 mm from the front edge of the scanner
Angle:

Curvature: R = ∞
Power-supply voltage: 3.7V

* Avoid direct or specula reflection from the light source as it may blind the scanners optical receiver.

α = 0°, β =＋15°, γ = 0°

°C
°C

OPN-3102n

1st

9.4 Dust and Drip Proof

IEC IP54 equivalent

Protection against solid objects: Level 5 equivalent (Dust proof type)
Prevent dust ingress to inside. Even if slight dust intrusion will not inhibit normal operation.

Protection against liquids: Level 4 equivalent (Splash proof type)
Protected against water splash from any direction.

* () is JIS drip-proof type.

22

SPECIFICATIONS MANUAL

9.5 Vibration Strength (without packing)

There shall be no sign of malfunction after the following vibration test.

Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated

velocity of 19.6m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in non-operating state.
Repeat this in each X, Y and Z direction.

9.6 Vibration Strength (in individual packing)

There shall be no sign of malfunction after the following vibration test.

Vibration test: Increase the frequency of the vibration from 10Hz to 100Hz at an accelerated

velocity of 19.6 m/s2 (2.0 G) for 30 minutes (60 minutes per cycle) in individually packaged state.
Repeat this in each X, Y and Z direction.

9.7 Drop Impact Strength (without packaging)

There shall be no sign of malfunction after the following drop test.

Drop test: Drop the scanner 18 times in total (3 times at each 6 face), from a height of 150 cm

onto a concrete floor as shown below.

OPN-3102n

1st

150cm

Figure 11: Drop Test

9.8 Drop Impact Strength (in individual packaging)

There shall be no sign of malfunction after the following drop test.

Drop test: Drop an individually packaged scanner 10 times in total, at any of 1 corner, 3 edges,

and 6 faces, from a height of 150 cm onto a concrete floor.

9.9 Electrostatic Discharge Immunity

Air discharge ±8 kV max. (No malfunction)

±15 kV max. (No destruction)

Measurement environment An electrostatic testing device compliant with IEC 61000-4-2

Discharge resistance 330 Ω
Charging capacitor 150 pF

23

SPECIFICATIONS MANUAL

10 Regulatory Compliance

10.1 LED Safety

IEC 62471:2006 Exempt_Group

10.2 Product Safety

EN60950-1:2005
IEC60950-1:2006

10.3 EMC

R & TTE Directive

・EN 55024:2010
・EN 55032:2012+AC:2013
・EN 301 489-1 V1.9.2
・EN 301 489-17 V2.1.1
・EN 300 328 V1.9.1
・EN 302 291-2 V1.1.1

FCC Part 15 Subpart C, Subpart B ClassB

Federal Communications Commission Notices

This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This product complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

Harmful Interference Notice
This product has been tested and complies with the specifications for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used according to the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which is found by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment or devices

• Connect the equipment to an outlet other than the receiver's

• Consult a dealer or an experienced radio/TV technician for assistance
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

VCCI Class B

This is a Class B product, to be used in a domestic environment, based on the Technical
Requirement of the Voluntary Control Council for Interference from Information Technology
Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it
may cause radio interference.

OPN-3102n

1st

24

SPECIFICATIONS MANUAL

10.4 Other

・Bluetooth logo certification
・Certification for Construction Design of Specified Radio Equipment

・Classification of Specified

Radio Equipment

・Model Name OPA-26X1
・Certificate Number 201-125603

Article 2 Paragraph 1, Item 19 Low power data
communication system in 2.4 GHz band

11 RoHS

RoHS compliance.
RoHS: The restriction of the use of certain hazardous substances in electrical and
electronic equipment, 2011/65/EU

12 Reliability

MTBF (Mean Time Between Failures) 50,000 hours

OPN-3102n

1st

13 Precautions

Handle this product carefully. Do not deliberately subject it to any of the following.

(1) Shock:

・ Do not drop this product from a height greater than specified in this manual.

・ Do not place this product under or between any heavy items.

・ Do not swing the cable around.

(2) Temperature Conditions:

・ Do not use this product at temperatures outside the specified range.

・ Do not pour boiling water on this product.

・ Do not throw this product into a fire.

(3) Foreign Materials:

・ Do not immerse this product in water or other liquid.

・ Do not expose this product to chemicals.

Others

・ Do not disassemble this product.

・ Do not use this product near a radio or a TV. It may cause reception problems.

・ This product may be affected by a momentary voltage drop caused by lightning.

・ Do not attach piece of metal or metal foil to the back of charging coil stored part and NFC coil

stored part. Also, do not fix anything that prevents placing to charging cradle.

・ Please securely close the USB cap to keep the waterproof.

・ Do not pull strong, fold and bend the cables.

・ Do not add shock or apply load to jack and connector.

・ When charging is completed, please remove USB cable from connector.

25

SPECIFICATIONS MANUAL

13.1 Radio Law

This product qualifies as specified radio equipment for radio stations of 2.4 GHz band data

communication system and has obtained the Certification for Construction

Design of Specified Radio Equipment. Therefore, radio station license is not required in Japan.

The following activities are prohibited under the Radio Law:

・Remodeling and disassembly

・Peeling off the certificate label

Do not use this equipment under the following environment, as radio interference may affect

other device and end up with causing physical or material damage.

・Safety apparatus and medical device for human body protection

・Environment where is concerned to cause serious damage

13.2 Bluetooth

・This product supports Bluetooth wireless communication with other Bluetooth devices that

have the same profile

・This product complies with Bluetooth standards; however, its communication performance

with untested devices is not guaranteed.

・Bluetooth devices use the 2.4 GHz frequency band that is shared among other devices. It

may affect the communication speed and distance between this product and the host device.

・The communication speed and distance vary depending on the interference and radio wave

condition between this product and the host device.

OPN-3102n

1st

13.3 Frequency Band

This product uses the 2.4 GHz frequency band. Read carefully the followings before using this

product.

In the frequency band of this product, scientific, medical and industrial devices including

microwaves are used. Also other radio stations including local private radio station for mobile

object identification requiring license for such as manufacturing lines at factories, specific

power-saving radio station requiring no license and amateur radio station are managed.

1. Make sure that “other radio stations” are not managed in the frequency band 2.4 GHz before

using this product.

2. In case that radio interference occurs between this product and “other radio stations,” change

the service space immediately, or stop transmitting radio wave to avoid the interference.

3. If you have any questions or troubles, please contact our sales office.

* This specification manual is subject to change without prior notice.

26

SPECIFICATIONS MANUAL

14 Product Labels

The product labels are affixed to the scanner as shown below.

OPN-3102n

1st

Unit: mm

Figure 12: Product Label Position

27

a

n

As

W

g

P

a

o

n

d

w

B

b

e

e

e

c

g

t

w

o

o

s

SPECIF

I

3

w

M

m

P

o

e

p

a

d

p

r

m

s

CATIONS

ANUAL

O

PN-3102n

1st

15 P

15.1 I

ckagin

dividual

sembled p

eight: Appr

Place i

*Place

Specifi

ackagin

ckage size:
x. kg

OPN-3

to the box wit
own without

ith Opticon l

ations

125 × 112 ×

02

h folded side
aped.

go upward.

40 (WDH

m)

Put MicroUS
product side
Make it thinn
overlap on th
Place the con
and taped sid

cable and
y side.
r so as not to
product.

necter on right

at the back.

*Do not f

Place
conne

ide

ld the barcode

Figure 1

neck strap on t
ctor, and place

when pasting

: Individual

p of USB cabl

QSG at the to

ackaging

Displ

123456=Pro
Dis

.

Individ

ay for the Se

『123456』

uct serial nu
lay 6-digets

ual box label:

ial-No.

ber.

erial number.

3A0002

28

C

0AsW

o

P

o

a

o

r

a

o

n

h

A

r

s

g

d

0

n

-

b

k

d

SPECIF

I

0

e

4

o

M

c

P

x

A

c

l

p

b

H

t

a

t

a

h

i

e

-

CATIONS

ANUAL

O

PN-3102n

1st

15.2

ollective

1

0pcs per b
sembled p

eight: Appr

Enter battery

battery」and ph

22-31-31」. A

either side of t

: Barcode Se

Stick the label

ackagin

x
ckage size
x. kg

P

cking box: 5B00

type 「Lithium io

ne number 「01

d place 1pc next

e packing box la

ial Label for Pac

on both front an

: 595 × 52

8 (100pcs per b

24­to
el.

ing Box

back side of the

× 245 (WD

x)

B: Mi

bo

seria

H mm)

ssing Serial Num

tta

h this label when

number s are ou

er Label:
here are more th
of order (not in

T

he order of serial

an 3 labels of wh

correct sequenc

No.

ch

).

Note: ‘R
declared

mark’ on the
by Optoelect

trays and the

onics Co., Lt

boxes for th

.

Figure 1

product indi

: Collective

ates that the

ackaging

roduct is Ro

S compliant

which is

29

16 Physical Features

16.1 Dimensions

83.0 × 36.0 × 21.5 (DWH mm)

16.2 Weight

Approx. 60 g (excluding accessories)

16.3 Mechanical Drawing

SPECIFICATIONS MANUAL

OPN-3102n

1st

Unit: mm

Figure 15: Mechanical Drawing

30

SPECIFICATIONS MANUAL

17 Supported Symbologies

17.1 Default Setting

The scanner is set to default by reading the following menu label.
Recorded contents of the NFC tag will also return to default.

Default

@MENU_OPTO@ZZ@SO@ZZ@OTPO_UNEM@

17.2 Supported Symbologies

17.2.1 1D Barcodes

Code type Default

UPC ○ -

UPC Add-on 2
UPC Add-on 5

EAN(JAN) ○ -

EAN Add-on 2
EAN Add-on 5

EAN-13 ○
EAN-13 Add-on 2

Code 39 ○ 1 Not transmit ST/SP

Tri-Optic ○ - Not transmit ST/SP

Codabar (NW7) ○ 1 Not transmit ST/SP

Industrial 2of 5 ○ 5

Interleaved 2of 5 ○ 6

S-Code 5
Code 128 ○ 1 GS1 conversion (setting required)

Code 93 ○ 1

IATA ○ 5

MSI/Plessey 3

UK/Plessey 2

Telepen 1

Code 11 1

Matrix 2 of 5 5

Chinese Post Matrix 2 of 5 -

Korean Postal Authority -

Intelligent Mail Barcode -

POSTNET -

JPN (Customer Barcode) -

EAN-13 Add-on 5
EAN-8 ○
EAN-8 Add-on 2
EAN-8 Add-on 5

Minimum

length

OPN-3102n

1st

Remarks

31

SPECIFICATIONS MANUAL

17.2.2 GS1 Databar, Composite Code

Code type Default Remarks

GS1 DataBar

・GS1 DataBar Omnidirectional
・GS1 DataBar Truncated
・GS1 DataBar Stacked
・GS1 DataBar Stacked Omnidirectional

GS1 DataBar Limited ○
GS1 DataBar Expanded

・GS1 DataBar Expanded
・GS1 DataBar Expanded Stacked

Composite GS1-DataBar

・CC-A
・CC-B
・Limited CC-A
・Limited CC-B
・Expanded CC-A
・Expanded CC-B

Composite GS1-128

・CC-A
・CC-B
・CC-C

Composite EAN

・EAN-13 CC-A
・EAN-13 CC-B
・EAN-8 CC-A
・EAN-8 CC-B

Composite UPC

・UPC-A CC-A
・UPC-A CC-B
・UPC-E CC-A
・UPC-E CC-B

OPN-3102n

1st

○

GS1

conversion (setting required)

○

GS1

GS1

GS1

GS1

conversion (setting required)

conversion (setting required)

conversion (setting required)

conversion (setting required)

17.2.3 2D Codes

PDF417 ○

Micro PDF417

Codablock F

QR Code ○ GS1 conversion (setting required)

Micro QR ○

Data Matrix (ECC 200) ○ GS1 conversion (setting required)

Data Matrix (ECC 000-140)

Aztec Code ○

Aztec Runes

Chinese-sensible code

Maxi Code

Code type Default Remarks

32