OptiPure QT2+MP, QT3MP, QTC2+MP, QTC3MP Installation, Operation & Maintenance Manual

Installation, Operation & Maintenance Manual

For: QT-Multi-Point Manifold Series

Models:

QT2+MP

QT3MP

QTC2+MP

QTC3MP

101 S. Gary Ave, suite A

Roselle, IL 60172

www.optipurewater.com

[phone]

P/N 970-09705
Rev:B 04/11/19

DO NOT DISCARD - GIVE THIS MANUAL TO THE OWNER AFTER INSTALLATION

● Installation must conform to all local plumbing codes and regulations.

● Do NOT use with water that is microbiologically unsafe or of unknown quality without adequate

isinfection before or after the system. Systems certified for cyst reduction may be used on

d

isinfected waters that may contain filterable cysts.

d

● Connect system to cold water supply only! Water temperature must not exceed 100°F/38°C.

● Do NOT solder plumbing connections attached to the assembly. High temperature will damage

these components.

● Do NOT over-tighten fitting connections. Always back-up valves and fittings with a wrench to
avoid turning the valve.

● Allow a minimum of 3” under the housing to allow for sump removal and filter replacement.

● Do NOT mount the system near a heat source or above the electrical wiring or any device or

area that would be adversely affected by water.

● Do NOT mount the system behind equipment. The unit must be easily accessible for filter
replacement.

● Failure to change cartridges per recommended intervals with OptiPure replacement cartridges
may lead to system failure and property damage.

2

Introduction:

Your new OptiPure QT-Series FoodService Filtration System will cleanse and condition the tap water
providing optimum water characteristics for their specified applications. The result is reduced
equipment maintenance requirements, longer equipment life and improved quality & consistency of
your products. The OptiPure System is built with the finest, most advanced materials and each

ystem is quality inspected and pressure tested prior to shipment. Proper system installation and

s
routine filter changes will ensure years of trouble-free operation and performance.

Please refer to this manual when performing routine filter changes. The instructions make periodic
maintenance quick and easy, and ensure you will receive maximum benefit from your system.

OptiPure Limited Warranty:

All system components and assembly except for replacement filter cartridges, separation
membranes, permeate pumps, electric motors, diaphragm pumps, and rotary vane pumps shall be
warranted against defects in workmanship for a period of 60 months from the date of original
shipment.
Replacement filter cartridges are warranted for defects in material and workmanship only.
Membrane failure due to fouling, hydrolysis, oxidation or other damage caused by the local water
conditions is not covered under warranty.

Permeate pumps, electric motors, diaphragm pumps, and rotary vane pumps shall be warranted
against materials and workmanship for a period of 12 months from the date of purchase and are
limited to the terms of warranty extended by the original equipment manufacturer.

Products should only be installed and operated in accordance with the recommended procedures
and guidelines from OptiPure. Products must be maintained and serviced with OptiPure approved
replacement parts and filters. Failure to replace filter cartridges or filter elements at recommended
interval or specified capacity will void warranty.

Contact OptiPure customer service or go to www.optipurewater.com for a detailed copy of the
warranty statement.

Obtaining Warranty Service:

To obtain warranty service the customer should:

1) Contact the authorized OptiPure dealer who supplied the product.

2) Call OptiPure’s customer service department for replacement parts and support.

3

HOW DOES FILTERTRAK WORK?

Simple, One-Time

R

egistration of

System with

FilterTrak!

2

. Change Notice

"Filter Change Due"

Notice Generated by

FilterTrak and

Received

Most Filters Shipped

Same Day.

Filters Changed by

On-site Store or

Service Personnel.

Change Information

Recorded in

FilterTrak.

Choose Upon Set-up to

Auto-Ship or Manually

Place Filter Orders

Filter Change

Acknowledged in

FilterTrak

3. Order Placed

1.Register

4. Filters Shipped

5.Filters Changed

6.Acknowledgement

Authorized Distributors

Available Through

Filtertrak® is an online application that

®

enables low maintenance service and filter
monitoring of water treatment systems,
ensuring customers get the full performance
of their system.

FilterTrak manages timely, proper filter
replacement which:

• Reduces maintenance

• Improves operating efficiency

• Assures the quality of ice, beverages, and
steam generating systems

For more information about FilterTrak,
please contact one of our foodservice
master distributors or go to:
www.optipurewater.com

4

System/ Operating Specification & Connections:

Maximum Pressure: 125 psi/8.6 bar
Operating Temperature: 35° - 100°F (2° - 32°C)
Inlet/Outlet Connections:

1/2” NPT Male Fittings Standard on all Multi-Point Systems

/4” NPT Male Fittings are optional

3
1/2” Push-In-Tube Connections are optional.

5