Optima Company EL-1500 User Manual

Page 1

The information contained in this document is subject to change without notice. Royal/Regal Optima ES-S M.G. – Rev. 0b (05/07) Code No. 0816510

Maintenance Guide

OPTIMA®Sensor Activated Flushometers

The Sloan OPTIMA automatic electronic Flushometer relies on an infrared sensor to detect a user and activate a flushing cycle. No physical contact with the Flushometer surface is necessary, assuring sanitary protection. OPTIMA Flushometers are ADA-compliant devices and are available in both Royal

and Regal®Flushometer models. These hardwire Flushometers require the use of 24 VAC Stepdown Transformers.

The Flushometer is triggered by means of a self-adaptive infrared sensor. A flashing red indicator light identifies the presence of a target. After a detected user moves out of the effective range of the sensor, a signal is sent to the Flushometer Solenoid and, after appropriate arming and/or flush delays, the flush cycle is initiated. When a unit is used intermittently, the Sentinel Flush feature ensures a cleansing cycle at least once in any 24-hour period.

NOTE: Sensor location and positioning is critical. Failure to properly position the electrical box to the recommended plumbing rough-in dimensions will result in improper installation and may impair product performance. All tradesmen (plumbers, electricians, tile setters, etc.) involved in the installation of this product must coordinate their work efforts to ensure proper product installation. Improper installation may nullify the manufacturer’s warranty.

OPTIMA®Components:

EL-1500 Series Sensor

• Self-adaptive Sensor

• Flashing Red Light Indicator

• Replaceable Sensor Window

• Two-wire connection system

• Surface Mounted (optional)

Solenoid

• Non-Hold-Open integral Solenoid operator

Transformer

24 VAC Stepdown Transformer

• EL-154 for 120 VAC Electrical Supply (50/60 Hz)

• EL-342 for 220/240 VAC Electrical Supply (50/60 Hz)

Override Button

• Courtesy Flush

(available only on Water Closet installations)

(also available on Concealed Water Closet ES-SM)

Cover Plates

• Override Button Sensor Cover Plate

(Exposed and Concealed Water Closet installations)

• Solenoid Cover Plate

(Exposed Water Closet and Urinal installations)

• Urinal Sensor Cover Plate

(Concealed Urinal installations)

Wall Box Option

• Stainless Steel or Polished Brass Surface Finish

• Concealed installation

• Vandal Resistant

LIMITED WARRANTY

Sloan Valve Company warrants its Flushometer Products to be made of first class materials, free from defects of material or workmanship under normal use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three years (one year for special finishes) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

Page 2

New Solenoid/Sensor Parts and Assemblies List

Item Code No. Part No. Description

1A. 3305043 EL-128-A Actuator Cartridge Assembly Repair Kit Includes Spring,

Plunger Guide, Solenoid Valve Seat, Valve Piston Assembly, and O-Ring (also available for ES-SM

Flushometers) 1B. 0305135 EL-110 O-Ring 2A. 0305329 EL-124-2 24 VAC Solenoid Assembly (exposed installation)

Includes Handle Coupling, 24 VAC Coil, Face Plate for

24 VAC Solenoid, Solenoid Adapter, Solenoid Shaft

Assembly, Nut for Solenoid, Solenoid Housing,

Solenoid Flux Plate, and O-Ring 2B. 0305331 EL-138-2 24 VAC Solenoid Assembly (concealed installation)

Includes Handle Coupling, 24 VAC Coil, Face Plate for

24 VAC Solenoid, Solenoid Adapter, Solenoid Shaft

Assembly, Nut for Solenoid, Solenoid Base Plate and

Solenoid Cover Assembly 3A. 0337086 DO-22 O-Ring 3B. 0305132 EL-104 RB Adapter for Solenoid 3C. 0305165 EL-163-A Solenoid Shaft Assembly Includes Gasket, Plunger,

Plunger Spring, and Solenoid Shaft

4. 0301082 A-6 CP Handle Coupling (exposed installation) 5A. 0305166 EL-164 Solenoid Flux Plate (exposed installation) 5B. 0305332 EL-542 Solenoid Base Plate (concealed installation)

6. 0305118 EL-165-2 24 VAC Coil 7A. 0305164 EL-162-2 CP Solenoid Housing (exposed installation) 7B. 0305336 EL-541-A Solenoid Cover Assembly (Includes Flux Plate)

8. 0305127 EL-102-2 Face Plate for 24 VAC Solenoid (exposed installation) 9A. 0305125 EL-101 CP Nut for Solenoid (exposed installation)

Item Code No. Part No. Description

9B. 0305167 EL-166 Housing Nut for Solenoid (concealed installation)

10. 0306249 F-15 Tail †

11. 0345150 EL-431-A CP Flange Assembly (exposed installation)

12. 0305152 EL-152 CP Screws (requires four screws per cover plate)

13. 0305151 EL-151 CP Cover Plate for Sensor and Solenoid Operator (Urinal only)

14. 0305219 EL-201 CP Cover Plate for Sensor and Override Button (Closet only)

15. 0318066 HY-66 CP Cover Plate for Solenoid Operator (Closet only)

16. 0305161 EL-161 CP Cover Plate for Sensor

17. 0305323 EL-168-A Yoke Assembly (Urinal only)

18. 0305324 EL-141-A Override Switch and Yoke Assembly (Closet only)

19. 3305620 EL-1500 Urinal Sensor Replacement Kit (Urinal only)

20. 3305621 EL-1500-L Closet Sensor Replacement Kit (Closet only)

21. 0345154 EL-154 Transformer (120 VAC) (also available for ES-SM Flushometers)

0345999 EL-342 Transformer (240 VAC) (also available for ES-SM

Flushometers)

22. 3345047 EL-461 Surface Mounted Sensor and Override Button Assembly (closet only)

23. 3345048 EL-497 Surface Mounted Sensor Assembly (urinal only)

24. 3345048 EL-297 Solenoid Assembly

25. 3365003 ETF-492-A Control Module

† NOTE: For exposed & concealed solenoids manufactured before 2003 or not

shown here, consult factory for individual part assembly.

ABBREVIATIONS:

CP . . . . . .Chrome Plated

RB . . . . . . .Rough Brass

gpf . . . .gallons per flush

Lpf . . . . . .Liters per flush

Repair Kits and Parts listed on these pages are designed to service all Sloan OPTIMA Diaphragm type Flushometers including those manufactured for Low Consumption (LC) usage.

Each item has been identified by a specific Part Number (in italics) with a corresponding Code Number (in bold). To expedite your replacement requirements, order by Code Number.

Exposed or Concealed Water Closet

Exposed

Urinal

Concealed

Urinal

10†

2A Exposed Solenoid

Exposed or

Concealed

Water Closet

2B Concealed Solenoid

Valve

New Style Solenoid Parts and

Assemblies

NOTE: Gang box is not supplied.

Concealed

Water Closet

Concealed

Urinal

24 ES-SM Solenoid

NOTE: Royal ES-SM surface mounted sensor

components are not compatible with ES-S flushometer components.

Royal ES-EM Surface Mounted Sensor Components

Page 3

ROYAL Installation

REGAL Installation

Valve Body

3736

Valve Body

To Solenoid

The Repair Kits and Parts listed on these pages are designed to service all Sloan OPTIMA Diaphragm type Flushometers, including those manufactured for Low Consumption (LC) usage.

Each item has been identified by a specific Part Number (in italics) with a corresponding Code Number (in bold). To expedite your replacement requirements, order by Code Number.

ABBREVIATIONS:

CP . . . . .Chrome Plated

RB . . . . . . .Rough Brass

SD . . . . . . .Screwdriver

WH . . . . .Wheel Handle

gpf . . .gallons per flush

Lpf . . . . .Liters per flush

39A 39B

Concealed WH

Valve Parts List

NOTE: Also refer to the Royal, Regal, Control Stop and Flush Connection Maintenance Guides.

Royal

Item Code No. Part No. Description

22. 0301172 A-72 CP Cover

23. 0301168 A-71 Inside Cover

24. SEE DIAPHRAGM ASSEMBLY CHART ON PAGE 4

25. 3323182 V-651-A Vacuum Breaker Repair Kit

26. 0393004 V-600-AA 3/4" (19 mm) x 9" (229 mm) CP Vacuum Breaker 0393006 V-600-AA 1-1/4" (32 mm) x 9" (229 mm) CP Vacuum Breaker 0393007 V-600-AA 1-1/2" (38 mm) x 9" (229 mm) CP Vacuum Breaker

27. 0306125 F-5-AW 3/4" (19 mm) CP Spud Coupling Assembly 0306140 F-5-AU 1-1/4" (32 mm) CP Spud Coupling Assembly 0306146 F-5-AT 1-1/2" (38 mm) CP Spud Coupling Assembly

28. 0308676 H-550 CP Stop Coupling

29. 0308801 H-551-A CP Adjustable Tail 2-1/16" (52 mm) long

30. 5308696 H-553 O-ring - 24 per pkg.

31. 3308386 H-700-A 1" (25 mm) Screwdriver Bak-Chek®Angle Stop CP - complete 3308384 H-700-A 3/4" (19 mm) Screwdriver Bak-Chek®Angle Stop CP - complete

32. 3308853 H-541-A-SD Control Stop Repair Kit for use with 1" (25 mm) & 3/4" (19 mm)

H-700-A, 1" (25 mm) H-600-A, 1" (25 mm) & 3/4" (19 mm) H-740-A and 1" (25 mm) H-540-A SD Stops

3308856 H-543-A-SD Control Stop Repair Kit for use with 3/4" (19 mm) H-600-A and

H-540-A SD Stops

33. 0308612 H-622 CP Bonnet for use with 1" (25 mm) & 3/4" (19 mm) H-700-A and 1"

(25 mm) H-600-A SD Stops

0308843 H-577 CP Bonnet for use with 3/4" (19 mm) H-600-A SD Stops

34. 3308791 H-1010-A 1" (25 mm) Vandal Resistant Control Stop Cap Assembly for use with

1" (25 mm) & 3/4" (19 mm) H-700-A and 1" (25 mm) H-600-A SD Stops

3308790 H-1009-A 3/4" (19 mm) Vandal Resistant Control Stop Cap Assembly for use

with 3/4" (19 mm) H-600-A SD Stops

35. 0308840 H-573 1" (25 mm) Control Stop Cap CP for use with 1" (25 mm) & 3/4"

(19 mm) H-700-A and 1" (25 mm) H-600-A SD Stops

0308848 H-582 3/4" (19 mm) Control Stop Cap CP for use with 3/4" (19 mm)

H-600-A SD Stops

36. 3308866 H-574 1" (25 mm) Control Stop Cap with Bumper for use with 1" (25 mm) &

3/4" (19 mm) H-700-A and 1" (25 mm) H-600-A SD Stops

37. 3308867 H-576 1" (25 mm) Control Stop Cap with Extended Bumper for use with 1"

(25 mm) & 3/4" (19 mm) H-700-A and 1" (25 mm) H-600-A SD Stops

38. 3308860 H-1006-A Repair Kit for 1" (25 mm) Stops with Concealed WH for use with 1"

(25 mm) H-700, H-600, and H-540 WH Series Stops

3308859 H-1007-A Repair Kit 3/4" (19 mm) Stops with Concealed WH for use with 3/4"

(19 mm) H-700 WH Series Stops

39. 0388010 H-730-A 1" (25 mm) Concealed WH Bak-Chek®Angle Stop RB 0388011 H-730-A 3/4" (19 mm) Concealed WH Bak-Chek®Angle Stop RB

39A. 3308872 H-1011-A Repair Kit (for Concealed WH only; does not include bonnet) 39B. 0208083 H-623 Bonnet

0308705 H-561 Bonnet

Regal

Item Code No. Part No. Description

23. 0301168 A-71 Inside Cover

28. 0308676 H-550 CP Stop Coupling

29. 0308801 H-551-A CP Adjustable Tail 2-1/16" (52 mm) long

30. 5308696 H-553 O-ring - 24 per pkg.

32. 3308853 H-541-A-SD Control Stop Repair Kit for use with 1" (25 mm) & 3/4" (19 mm)

H-700-A ,1" (25 mm) H-600-A, 1" (25 mm) & 3/4" (19 mm) H-740-A and 1" (25 mm) H-540-A SD Stops

3308856 H-543-A-SD Control Stop Repair Kit for use with 3/4" (19 mm) H-600-A and

H-540-A SD Stops

40. 0317004 R-10 CP Cover

41. SEE INSIDE PARTS ASSEMBLY CHART ON PAGE 4

42. 3323192 V-551-A Vacuum Breaker Repair Kit

43. 0323005 V-500-AA 3/4" (19 mm) x 9" (229 mm) CP Vacuum Breaker 0323006 V-500-AA 1-1/4" (32 mm) x 9" (229 mm) CP Vacuum Breaker 0323007 V-500-AA 1-1/2" (38 mm) x 9" (229 mm) CP Vacuum Breaker

44. 0306102 F-54-A 3/4" (19 mm) CP Spud Coupling Assembly 0306142 F-55-A 1-1/4" (32 mm) CP Spud Coupling Assembly 0306145 F-56-A 1-1/2" (38 mm) CP Spud Coupling Assembly

45. 0388029 H-740-A 1" (25 mm) SD Bak-Chek®Stop CP - complete 0388031 H-740-A 3/4" (19 mm) SD Bak-Chek®Stop CP - complete

46. 0308991 H-639 CP Bonnet for use with H-740-A 1" (25 mm) & 3/4" (19 mm) and

H-540-A 1" (25 mm) SD Stops

0308601 H-538 CP Bonnet for use with H-540-A 3/4" (19 mm) SD Stops

47. 5308156 H-37 CP Cap (package of 6)

48. 5310034 J-2/J-7 Bumper Assembly (package of 6)

Page 4

To identify the Flush Volume of a DUAL FILTERED DIAPHRAGM ASSEMBLY, look at the color of the Relief Valve, the Refill Head and the shape of Flow Ring.

‡ NOTE: Water Closet Refill

Heads (Gray) have larger slots than Urinal Refill Heads (Black).

Royal ES-S & ES-SM — item 24 — Dual Filtered Diaphragm™ Assembly

Sold ONLY in ROYAL Performance™ Kits

ES-S KIT includes: EL-128-A Actuator Cartridge Assembly (item 1A); Dual Filtered Diaphragm Assembly (item 24);

High Back Pressure Vacuum Breaker Repair Kit (item 25); and one Tailpiece O-Ring (item 30)

Diaphragm Only KIT includes: Dual Filtered Diaphragm Assembly (item 24) ONLY

ES-S KIT DIAPHRAGM ONLY KIT

Code No. Kit No. Code No. Kit No. Flush Volume Use with Relief Valve Refill Head‡ Flow Ring

A 3345013 EL-1101-A 3301502 A-1041-A 1.6 gpf/6.0 Lpf Low Consumption Water Closets Green Gray Smooth

3345014

EL-1102-A

3301501

A-1038-A 3.5 gpf/13.2 Lpf Water Saver Water Closets White Gray Smooth

C 3345015 EL-1103-A 3301505 A-1044-A 2.4 gpf/9.0 Lpf 9 Liter European Water Closets Blue Gray Smooth

D 3345016 EL-1106-A 3301504 A-1043-A 0.5 gpf/1.9 Lpf Wash Down Urinals Green Black Smooth & Slotted

E 3345017 EL-1107-A 3301503 A-1042-A 1.0 gpf/3.8 Lpf Low Consumption Urinals Green Black Slotted

3345018

EL-1108-A

3301500

A-1037-A 1.5 gpf/5.7 Lpf Water Saver Urinals Black Black Smooth

Regal ES-S — item 41 — Inside Part Kits Assembly

A-36-A A-37-A A-38-A A-41-A A-42-A A-43-A A-44-A

3301036 3301037 3301038 3301041 3301044 3301081 3301024

4.5 gpf/17.0 Lpf 1.5 gpf/5.7 Lpf 3.5 gpf/13.2 Lpf 1.6 gpf/6.0 Lpf 1.0 gpf/3.8 Lpf 0.5 gpf/1.9 Lpf 2.4 gpf/9.0 Lpf

CLOSET URINAL CLOSET CLOSET URINAL URINAL CLOSET

Regal Inside Parts List †

Item Code No. Part No. Description

A 5301058 A-19-AC Relief Valve, White (Closet) B 5301059 A-19-AU Relief Valve, Black (Urinal) C 5301211 A-19-ALC Relief Valve, Green

(Closet/Urinal-Low Consumption)

D 5301143 A-19-AL Relief Valve, Blue (9 Liter

Closet) E 5301111 A-15-A Disc F 5301188 A-156-A Diaphragm G 5301236 A-163-A Guide Assembly

4.5 gpf/17.0 Lpf Closet and

1.5 gpf/5.7 Lpf Urinal

H 5301032 A-152-A Guide Assembly

3.5 gpf/13.2 Lpf Closet

I 5301031 A-151-A Guide Assembly

1.6 gpf/6.0 Lpf Closet

J 5301155 A-155-A Guide Assembly

1.0 gpf/3.8 Lpf Urinal

K 5301157 A-157-A Guide Assembly

0.5 gpf/1.9 Lpf Urinal

† NOTE: All Regal inside part items are supplied in packages of 12.

Wall Box Kits

Closet Models

Code No. Part No. Description

— 3305180 EL-192-A Closet Wall Box Kit - Stainless Steel

Includes four EL-125 Mounting Screws, four

EL-126 Hex Nuts, four EL-127 Lock Washers,

EL-195 Mounting Bracket, EL-196 Electrical Box,

EL-197 Electrical Box Cover, EL-141-A Override

Switch Subassembly, EL-216 Wall Box 13" x 17"

(330 mm x 432 mm) with 14.5” x 18.5”

(368 mm x 470 mm) Stainless Steel Wall Box

Cover with hole for override switch, EL-318

Spanner Bit, EL-1500-L Closet Sensor

Replacement Kit, and four WB-6 Screws.

— 3305179 EL-192-A Closet Wall Box Kit - Polished Brass Includes the

same components as 3305180 listed above

except unit is furnished with Polished Brass

14.5" x 18.5" (368 mm x 470 mm) Wall Box

Cover (instead of Stainless Steel).

Urinal Models

— 3305178 EL-191-A Urinal Wall Box Kit - Stainless Steel Includes four

EL-125 Mounting Screws, four EL-126 Hex Nuts,

four EL-127 Lock Washers, EL-193 Wall Box

13" x 17" (330 mm x 432 mm) with

14.5” x 18.5”(368 mm x 470 mm) Stainless

Steel Wall Box Cover, EL-195 Mounting Bracket,

EL-196 Electrical Box, EL-197 Electrical Box

Cover, EL-318 Spanner Bit, EL-1500 Urinal

Sensor Replacement Kit, and four WB-6 Screws.

— 3305177 EL-191-A Urinal Wall Box Kit - Polished Brass Includes the

same components as 3305178 listed above

except unit is furnished with Polished Brass 14.5"

x 18.5" (368 mm x 470 mm) Wall Box Cover

(instead of Stainless Steel).

EL-216 Closet

EL-193 Urinal

EL-125

EL-126

EL-127

EL-195

EL-196

EL-125

WB-6

EL-197

EL-141

EL-1500-L

Closet

EL-1500

Urinal

Panel

Shown with

hole for

Override

Switch (Closet

applications

only)

Page 5

Sensor Replacement

NOTE: The EL-1500 Series OPTIMA Sensor (a two-wire unit) replaces the older

EL-150 Series Sensors (either three-wire or four-wire units). Refer to the Wiring History shown below.

IMPORTANT

• Be certain to disconnect the 24 VAC power supply either at the transformer or the fuse box. Failure to disable the power supply can result in damage to the EL-1500 series Sensor.

• The Solenoid Operator must be removed from the Valve on exposed urinal installations. Do not damage the O-ring seal on the operator assembly.

1. Remove the Cover Plate (for Wall Box Installation, remove Cover Panel) and old Sensor from the wall installation. Use a 5/64" hex wrench to remove the Cover Plate Screws (or #8 drilled spanner head screwdriver EL-318 to remove the vandal-resistant screws from the Wall Box Cover Panel.)

2. Connect one 24 VAC lead to the Sensor terminal labeled “24 VAC IN” (see Figure 1B).

• On an old three-wire EL-150 series Sensor, this wire was connected to the BLACK Sensor lead.

• On an old four-wire EL-150 series Sensor, this wire was connected to the BROWN Sensor lead.

3. Connect one Solenoid lead to the Sensor terminal labeled “TO VALVE” (see Figure 1B).

• On an old three-wire or four-wire EL-150 series Sensor, this wire was connected to the RED Sensor lead.

4. Connect the remaining 24 VAC lead to the remaining Solenoid lead.

• On an old three-wire EL-150 series Sensor, these wires were connected to the WHITE Sensor leads.

• On an old four-wire EL-150 series Sensor, these wires were connected to the YELLOW and BLUE (or in very early models, the inner BROWN).

5. On Water Closet installations only, connect the Override Button (shown as the Override Switch in Wiring Diagram) parallel to the EL-1500-L Sensor.

6. Reinstall the Sensor with the orientation arrow on the Lens side of the Sensor pointing UP (see Figure 1A). Replace the Cover Plate (or Wall Box Panel) and tighten the Cover Plate (or Wall Box Panel) Screws.

7. Reconnect the 24 VAC power supply at the transformer or the fuse box.

Figure 1A

Figure 1B

ORIENTATION ARROW

“24 VAC IN”

CONNECTION

“TO VALVE”

CONNECTION

WIRING DIAGRAM

120 VAC

UNIT #1

UNIT #2

THRU

#10

(IF USED)

24 VAC

OVERRIDE SWITCH ‡

OVERRIDE

SWITCH ‡

EL-1500 SERIES

SENSOR

EL-1500 SERIES

SENSOR

24 VAC COIL

COIL WIRE

‡ OVERRIDE SWITCH USED

WITH WATER CLOSETS ONLY

NOTE: A MAXIMUM OF TEN (10) SENSOR FLUSHOMETER UNITS CAN OPERATE

FROM ONE (1) SLOAN EL-154 TRANSFORMER. CLASS 2 UL LISTED, 48 VA (MIN.) AT 24 VAC, PLATE MOUNTED.

Figure 2

Start-Up Mode

NOTE: It is important that only

permanent targets are present at this time.

The self-adaptive sensor automatically adjusts to the surrounding environment when the 24 volt supply is activated. No manual adjustment is required. The start-up cycle completes in approximately five (5) minutes. A continuous red light visible in the sensor window indicates the Start-up Mode. if the red light flashes, the Sensor detects a target. Unless this target is a permanent fixture in the Sensor’s environment (i.e., a wall or stall door), it must be removed from the view of the Sensor. If a target is permanent, the Sensor will adapt itself around this target. In this case, the Start-Up Mode may take up to 10 (ten) minutes. When the Start-Up cycle is complete, the red light will no longer be visible in the Sensor Window.

NOTE: If the 24 volt power supply is

ever interrupted for longer than fifteen (15) seconds, the start-up mode begins automatically when power is restored.

Incorrect wiring or a short in the 24 volt power supply will initiate a warning signal in the Sensor Window. The visible light flashes a continuous “S-O-S” signal: three (3) slow, three (3) fast, and three (3) slow flashes.

EL-150 Wiring History

for 4-wire and 3-wire sensors

Brown

Red

Brown

Red

Red with Yellow or all Yellow

Brown

Blue

Red

Yellow

Brown

Black

White

Release date 03/09/78

Release date 08/11/83

Release date 02/02/87

Release date 12/12/90

Page 6

1. PROBLEM: Valve does not function (red light does not flash when user steps in front of sensor).

CAUSE: No power is being supplied to sensor.

SOLUTION: Ensure that the main power is turned “ON.” Check

transformer, leads and connections. Repair or replace as necessary.

CAUSE: EL-1500/EL-1500-L Sensor is not operating.

SOLUTION: Replace EL-1500/EL-1500-L Sensor.

2. PROBLEM: Valve does not function (red light flashes when user steps in front of Sensor).

INDICATOR: Red light stops flashing when user steps away and

valve makes a “clicking” sound but does not flush.

CAUSE: No water is being supplied to the valve.

SOLUTION: Make certain that water supply is turned “ON” and the

Control Stop is open.

CAUSE: EL-128-A cartridge is fouled or jammed.

SOLUTION: Turn electronic power to valve “OFF” (failure to do so

could result in damage to the solenoid coil). Remove the solenoid operator from the valve and remove the EL-128-A cartridge. Clean and/or repair as necessary.

INDICATOR: The red light stops flashing when user steps away but

the valve does NOT make a “clicking” sound and does NOT flush.

CAUSE: EL-163-A solenoid shaft assembly is fouled or jammed.

SOLUTION: Turn electronic power to valve “OFF” (failure to do so

could result in damage to the solenoid coil). Remove EL-101 or EL-166 nut from the solenoid operator. Remove the coil from the solenoid operator. Use a spanner wrench or pliers to remove the EL-163-A solenoid shaft assembly from valve. Clean and/or replace as necessary. Be sure to replace plunger spring when reassembling Solenoid Shaft Assembly.

INDICATOR: The red light flashes three (3) short flashes, three (3)

long flashes then three (3) short flashes (“S-O-S”) and continues to repeat this cycle even when user steps out of the sensor’s detection range.

CAUSE: EL-1500/EL-1500-L Sensor wiring connections are

incorrect.

SOLUTION: Rewire Sensor to valve. One solenoid lead connects to

the “TO VALVE” connection on Sensor. One transformer lead connects to the “24 VAC IN” connection on Sensor. Second solenoid lead and second transformer lead connect together.

CAUSE: Wiring to Sensor is ground shorted.

SOLUTION: Find short in wiring circuit and correct.

CAUSE: EL-165-2 solenoid coil is burnt out or coil is not

connected to solenoid plunger shaft.

SOLUTION: Reinstall or replace coil as necessary.

3. PROBLEM: Volume of water is insufficient to adequately siphon fixture.

CAUSE: Control Stop is not open wide enough.

SOLUTION: Adjust control stop for desired water delivery.

CAUSE: Low Consumption unit is installed on Water Saver or

Conventional fixture.

SOLUTION: Replace Diaphragm component parts of valve with kit

that corresponds to appropriate flush volume of fixture.

CAUSE: Inadequate water volume or pressure available from

supply.

SOLUTION: Increase pressure or supply (flow rate) to the valve.

Consult factory for assistance.

4. PROBLEM: Length of flush is too long (long flushing) or valve fails to shut off.

CAUSE: Water Saver valve is installed on Low Consumption

fixture.

SOLUTION: Replace Diaphragm component parts of valve with kit

that corresponds to appropriate flush volume of fixture.

CAUSE: Relief valve in diaphragm is not seated properly or

bypass hole in diaphragm is clogged.

SOLUTION: Disassemble inside Diaphragm component parts and

wash parts thoroughly. Replace worn parts if necessary.

5. PROBLEM: Water splashes from fixture.

CAUSE: Supply flow rate is more than necessary.

SOLUTION: Adjust Control Stop to meet flow rate required for proper

cleansing of the fixture.

CAUSE: Closet valve is installed on urinal fixture.

SOLUTION: Replace closet Diaphragm component parts with proper

urinal kit (Inside Diaphragm Assembly or Inside Parts Kit)

The information contained in this document is subject to change without notice.

SLOAN VALVE COMPANY • 10500 SEYMOUR AVENUE • FRANKLIN PARK, IL 60131

Phone: 1-800-9-VALVE-9 or 1-847-671-4300 • Fax: 1-800-447-8329 or 1-847-671-4380 • www.sloanvalve.com

Troubleshooting Guide

NOTE: Upon detection of the user, the red indicator light flashes slowly for a period of eight seconds. When the user leaves the detection range, the indicator light flashes

rapidly and the Sensor initiates the flush sequence. Then the indicator light stops flashing and the valve flushes. (On water closet models, the valve will flush after

a three-second delay).

Maintenance Guide

Care and Cleaning Instructions

DO NOT USE abrasive or chemical cleaners to clean Flushometers that may dull the luster and attack the chrome or decorative finish. Use ONLY soap and water, then wipe dry with a clean towel or cloth. When cleaning the bathroom tile, protect the Flushometer from any splattering of cleaner. Acids and cleaning fluids can discolor or remove chrome plating.

If further assistance is required, please contact Sloan Valve Company Installation Engineering Department at:

1-888-SLOAN-14

(1-888-756-2614)

Control Stop Setting

IMPORTANT: Never open Control Stop to where the flow from the valve exceeds the flow capability of the fixture. In the event of a valve failure, the fixture must be able to accommodate a continuous flow from the valve.