Optima Company DSB2 User Manual
OPtima PC
Contents
1. Introduction ................................................................................................................................................ 2
2. Installation ................................................................................................................................................ 2
2.1 CE EMC Compliance..................................................................................................................... 2
2.2 Mounting........................................................................................................................................ 2
2.3 Wiring ............................................................................................................................................ 2
2.4 Adding Hardware........................................................................................................................... 7
3. Peripheral Devices ..................................................................................................................................... 9
4. The Operating System................................................................................................................................ 9
4.1 BIOS Password Settings ............................................................................................................... 9
5. Setup .............................................................................................................................................. 10
5.1 Windows NT Setup ...................................................................................................................... 10
5.2 Installing the Wonderware License.............................................................................................. 11
5.3 Power Shutdown/Battery Backed Power Supply......................................................................... 11
5.4 Backups....................................................................................................................................... 11
6. The Display .............................................................................................................................................. 11
6.1 The Touchscreen......................................................................................................................... 11
7. Keyboard Functionality (Model DSA2 only).............................................................................................. 12
7.1 Function Keys.............................................................................................................................. 12
7.2 Numeric Keyboard....................................................................................................................... 12
7.3 Left/Right Mouse Buttons ............................................................................................................ 13
7.4 Cursor Keys ................................................................................................................................. 13
7.5 Machine Function Keys sent as Keyboard Buttons ..................................................................... 13
7.6 Machine Function Keys as Interbus-S Buttons............................................................................ 13
8. Environmental Specifications ................................................................................................................... 13
9. Automatic Logon to Windows NT ............................................................................................................. 14
9.1 Disabling AutoLogon ................................................................................................................... 14
9.2 Bypassing AutoLogon.................................................................................................................. 14
9.3 Changing the Username and Password ...................................................................................... 14
9.4 Using the Registry Editor............................................................................................................. 14
10. Troubleshooting/Application Tips ............................................................................................................. 15
11. Disconnecting the Display ........................................................................................................................ 16
12. End User License Agreement................................................................................................................... 16
Figures
Figure 1. Model DSA2 Dimensions for Flange Mount .................................................................................. 3
Figure 2. Model DSA2 Dimensions for Panel Mount .................................................................................... 4
Figure 3. Model DSB2 Dimensions for Flange Mount .................................................................................. 5
Figure 4. External Floppy Drive Cutout and Dimensions.............................................................................. 6
Figure 5. SA85 Board Jumpers & Switches................................................................................................. 7
Figure 6. Model DSA2 Keyboard ................................................................................................................ 12
Figure 7. Disconnecting the Display ........................................................................................................... 16
1. Introduction
2. Installation
The OPtima PC is made up of a single board computer with a 233 Mhz processor. It has 1 PCI expansion slot and 2 ISA expansion slots. External connectors
are provided for 1 parallel port and 1 serial port. Connectors are also provided for
attaching an external monitor and keyboard. The Model DSA2 is equipped with a
10.4” (800 x 600 pixels) active matrix “touchscreen” display, a floppy disk drive
and a proprietary keyboard. The Model DSB2 is equipped with a 15” (1024 x 768
pixels) active matrix “touchscreen” display and an (optional) floppy disk drive.
The PC is supplied with a minimum of 64 MB of EDO RAM, with support for up to
128 MB. It also has 2 MB of on-board display memory, which is not expandable.
This memory , along with the PCI-bus and on-board graphics controller , provides a
64-bit graphics engine which is excellent for most display intensive applications.
Note that for best results when using Wonderware, screens sets should be developed in the same resolution as the particular OPtima PC that is being used.
Although Wonderware provides a means of “converting” resolutions, some elements may not appear as would be expected.
This is an Installation Category 3 and Pollution Degree 2 device. The wiring
guidelines outlined in this manual are to be used in addition to all applicable
electrical and safety codes. Be sure to follow all requirements of such codes as
well as other recognized safety practices.
2.1 CE EMC Compliance
2.2 Mounting
2.3 Wiring
Wiring guidelines to ensure the machine is CE EMC compliant are included in this
document. For additional wiring information, refer to the following publications:
Recommended Guideline for Wiring & Grounding Machine Controls
Society of the Plastics Industry, Inc.
1275 K Street, N.W.–Suite 400
Washington, D.C. 20005
(202) 371-5200
IEEE Guide for the Installation of Electrical Equipment to Minimize Electrical Noise
Inputs to Controllers from External Sources
(IEEE Std 518-1982)
Do not enclose the operator station in a small or tightly sealed cabinet or panel
which would cause the surrounding temperature to exceed the rated temperature. Consideration must also be given to protecting the display surface. Do not
mount the operator station so that the display is subject to mechanical damage or
dust and dirt particles. Periodic cleaning using a soft, water-dampened cloth is
recommended. Do NOT spray liquid cleaning agents directly onto the operator
station. No matter which of the mounting versions is used, allow adequate room
for vibration, air circulation and easy access. Pay particular attention to the accessibility of cable connectors.
The OPtima PC must be operated from a 24 Vdc Class 2 input. This unit requires 24
Vdc at 5 Amps, maximum. If an AC supply is required to provide the 24 Vdc, a
standard 1 10 Watt supply with 24 Vdc output will suffice. Note that inadvertent power
loss (or shutdown) may cause application problems. A battery-backed power supply
is recommended in order to keep the OPtima running during times of power loss.
The bond strap must be connected at the nearest panel location.
1660-IN-010-0-04Page 2
Include a switch or circuit breaker in the installation. It must be placed in close proximity to the equipment,
within easy reach of the operator and must be marked as the disconnecting device for the equipment.
Remove cover for access to
expansion slots.
19.462
1.873
7.483
7.483
1.873
.375
12.620
5.000.375
11.000
Ø .218 (10)
3.435
17.844
1.423
0.075
5.481
5.0003.435
Parallel port
PCI expansion slot
Serial port (COM1)
CRT port
Internal keyboard
ISA expansion slot
ISA expansion slot
External keyboard (mini-DIN)
Interbus-S In (pins)
Interbus-S Out (sockets)
for machine function keys
Chassis Ground
DC - (0 Vdc)
DC + (24 Vdc)
24 Vdc
Class 2 Input
Power Switch
Bond Strap
3.435
0.310
1.873
7.483
17.992
11.150
Figure 1. Model DSA2 Dimensions for Flange Mount
7.483
1.873
11.250
Ø .218 (10)
18.092
1660-IN-010-0-04 Page 3
0.750
6.979
16.742
Include a switch or circuit breaker in the installation. It must be placed in close proximity to the equipment,
within easy reach of the operator and must be marked as the disconnecting device for the equipment.
0.550
7.450
11.000
Shock mounts
are 1/4-20 threads
Remove cover for access to
expansion slots.
Serial port (COM1)
PCI expansion slot
Interbus-S In (pins)
17.844
Interbus-S Out (sockets)
for machine function keys
External keyboard (mini-DIN)
ISA expansion slot
ISA expansion slot
CRT port
Internal keyboard
Parallel port
Chassis Ground
DC - (0 Vdc)
DC + (24 Vdc)
24 Vdc
Class 2 Input
Power Switch
Bond Strap
Figure 2. Model DSA2 Dimensions for Panel Mount
16.747
16.737
7.455
7.445
Ø.218 (4)0.5500.550
Solid lines
represent outside
of unit (front view)
1660-IN-010-0-04Page 4
Include a switch or circuit breaker in the installation. It must be placed in close proximity to the equipment,
within easy reach of the operator and must be marked as the disconnecting device for the equipment.
.180
Note that this panel cutout
applies to both the
Model DSB2 and
the Remote I/O Station
ISA expansion slot
ISA expansion slot
Serial port (COM1)
CRT port
Internal keyboard
PCI expansion slot
Parallel port
18.100
11.640 11.280
7.500
7.5001.550
Ø .188 (6)
Chassis Ground
DC - (0 Vdc)
DC + (24 Vdc)
24 Vdc
Class 2 Input
Bond Strap
Power Switch
External keyboard (mini-DIN)
.675
#8 - 32 Thread
(6 places)
6.575.375
11.000
.775
.779
2.200
7.500 7.500
17.842
12.550
11.640
.455
19.400
Figure 3. Model DSB2 Dimensions for Flange Mount
1660-IN-010-0-04 Page 5
4.0
g
ppy
(101.6)
Cable
Clearance
6.86 (139.7)
6.0 (152.4)
0.688
(17.5)
3.0
(76.2)
Front ViewSide View
External Floppy Drive
Dimensions shown in inches;
millimeters in parenthesis ( ).
Drive must be mounted within
15 in. (381 mm) of OPtima
cable connector.
flo
Figure 4. External Floppy Drive Cutout and Dimensions
2.1
(53.3)
#6 tap thru (4)
5.5 (139.7)
5.1 (129.5)
Cutout and
Mountin
2.5
(63.5)
Pattern
1660-IN-010-0-04Page 6
Loading...