Optima Centoris V480 User Manual

Page 1
Page 2
Page 3
I
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, trans­mitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trade­marks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. ©March 2008
Trademarks
This product incorporates copyright protection technology that is protected by method claims of certain U.S. pat­ents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended fo r home or other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineer­ing or disassembly is prohibited. Intel, Celeron, and Intel Core are trademarks/registered trademarks of Intel Corporation.
Page 4
II
Preface
FCC Statement
(Federal Communications Commission)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in­stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Re orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the service representative or an experie nc ed radio/TV technician for help.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not ex­pressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the equipment.
Page 5
III
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:
1. Do not use this product near water, for example near a bath tub, wash bowl, kitche n sink or laundry tub, in a wet basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit (Full Range AC/DC Adapter – AC Input 100 ­240V, 50 - 60Hz, DC Output 19V, 3.42A OR 18.5V, 3.5A).
CAUTION
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER,
TELECOMMUNICATION LINE CORD
This Computer’s Optical Device is a Laser Class 1 Product
Page 6
IV
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
2. Keep it dry, and don’t overheat it. Keep the computer and powe r supply away from any kind of heating ele- ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly dam­aged.
Do not expose the computer to any shock or vibration.
Do not place it on an unstable surface.
Do not place anything heavy on the computer.
Do not expose it to excessive heat or direct sunlight.
Do not leave it in a place where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on any surface that will block the Vents/Fan Intakes.
Page 7
V
Preface
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper workin g proc edu res for the comput er. Shut the computer down properly and don ’t forge t to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
5. Take care when using peripheral devices.
Do not turn off the power until you properly shut down all pro­grams.
Do not turn off any peripheral devices when the computer is on.
Do not disassemble the com­puter by yourself.
Perform routine maintenance on your computer.
Use only approved brands of peripherals.
Unplug the power cord befor e attaching peripheral devices.
Page 8
VI
Preface
Power Safety
The computer has specific power requirements:
• Only use a power adapter approv ed for use with this computer.
• Your AC/DC adapter may be design ed for intern ational travel but it still re quires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.
• The power adapter may have either a 2-pr ong or a 3-prong ground ed plug. The third prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the power cord, be su re to disconnect it by the plug head, not by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external power sup­plies (i.e. AC/DC adapter or car adapter).
Do not plug in the power cord if you are wet.
Do not use the power cord if it is broken.
Do not place heavy objects on the power cord.
Power Safety
Warning
Before you undertake any upgrade proce­dures, make sure that you have turned off the power, and discon­nected all peripherals and cables (including telephone lines). It is advisable to also re­move your battery in order to prevent acci­dentally turning the machine on.
Page 9
VII
Preface
Battery Precautions
Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
Do not remove any batteries from the computer while it is powered on.
Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way . Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
Do not try to repair a battery pack. Refer any battery pack repa ir or replacemen t to your servi ce represent ative or qual­ified service personnel.
Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode or leak if exposed to fire, or improperly handled or discarded.
Keep the battery away from metal appliances.
Affix tape to the battery contacts before disposing of the battery.
Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Page 10
VIII
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:
When the power cord or AC/DC adapter is damaged or frayed.
If the computer has been exposed to rain or other liquids.
If the computer does not work normally when you follow the operating instructions.
If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before turning the computer on.
Page 11
IX
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However ,
check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its ca rrying bag and secure it with the bag’s straps.
7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or req uire proof of ownersh ip for both hard -
ware and software. Make sure your “papers” are handy.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. T o prevent your computer from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.
Page 12
X
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knock­ing the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the com­puter, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note: Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer. Wait a few minutes before turning it on so that any moisture can evaporate.
Page 13
XI
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in fron t of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain:
Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Your knees should be slightly higher than your hips. Place your feet flat on the floor or on a footrest if necessary.
Use a chair with a back and adjust it to support your lower back comfortably.
Sit straight so that your knees, hips and elbows form approximately 90-degree an gles when you are working.
Take periodic breaks if you are using the computer for long periods of time.
Remember to:
Alter your posture frequently.
Stretch and exercise your body several times a day.
Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.
Page 14
XII
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders.
Position the display to avoid glare or reflections from overhead lighting or outside sources of light .
Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
Position the display directly in front o f you at a comfortable viewing distance.
Adjust the display-viewing angle to find the best position.
LCD Screen Care
To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions:
Set the Windows Power Plans to turn the screen off after a few minutes of screen idl e time.
Use a rotating, moving or blank screen saver (this prevents an image from being displayed too lo ng).
Rotate desktop background images every few days.
Turn the monitor off when the system is not in use.
Page 15
XIII
Preface
Contents
Notice ................................................................................. I
FCC Statement .............................................................II
Instructions for Care and Operation ..........................IV
Power Safety ..............................................................VI
Battery Precautions ...................................................VII
Cleaning .................................................................. VIII
Servicing ................................................................. VIII
Travel Considerations ................................................IX
Quick Start Guide
Overview ........................................................................1-1
Advanced Users ...........................................................1-2
Beginners and Not-So-Advanced Users ......................1-2
Warning Boxes ............................................................1-2
Model Differences .......................................................1-3
Not Included ................................................................1-3
System Software ..........................................................1-4
System Startup ...............................................................1-5
System Map: LCD Panel Open - Model A ....................1-6
System Map: LCD Panel Open - Model B ....................1-7
LED Indicators ................................................. ..............1-8
Hot Key Buttons & Keyboard .......................................1-9
Function Keys ...................................................... .... ....1-10
System Map: Front & Rear Views ...............................1-11
System Map: Left View ...............................................1-12
System Map: Right View .............................................1-13
System Map: Bottom View ..........................................1-14
Windows Vista Start Menu & Control Panel ...............1-15
Video Features .............................................................1-16
Display Devices & Options ......................................1-16
Power Options ............................................ ..................1-18
Features & Components
Overview ........................................................................2-1
Hard Disk Drive .............................................................2-2
Optical (CD/DVD) Device ............................................2-3
Loading Discs ..............................................................2-3
Handling CDs or DVDs ...............................................2-4
DVD Regional Codes ..................................................2-5
7-in-1 Card Reader .........................................................2-6
ExpressCard Slot ............................................................2-7
Inserting and Removing ExpressCards ........................2-7
Function Keys/Hot Keys ................................................2-8
Application Hot Key ...................................................2-9
Mail Checker ................................................................2-10
TouchPad and Buttons/Mouse .....................................2-11
Page 16
XIV
Preface
Configuring the TouchPad and Buttons ...................2-11
Audio Features .............................................................2-12
Adding a Printer ...........................................................2-13
USB Printer ...................................................... .... ....2-13
Parallel Printer ..........................................................2-13
Power Management
Overview ........................................................................3-1
The Power Sources ........................................................3-2
AC/DC Adapter ................................................. .... ......3-2
Battery .........................................................................3-2
Turning on the Computer ...............................................3-3
Power Plans ...................................................................3-4
Power-Saving States ......................................................3-6
Sleep ...........................................................................3-6
Hibernate ....................................................................3-7
Shut Down ..................................................................3-7
Configuring the Power Buttons .....................................3-8
Resuming Operation ...................................................3-9
Battery Information .....................................................3-10
Battery Power ...........................................................3-10
Conserving Battery Power ...........................................3-11
Battery Life .............................................................. ....3-12
New Battery ..............................................................3-12
Recharging the Battery with the AC/DC Adapter .....3-12
Proper handling of the Battery Pack .........................3-13
Battery FAQ ..............................................................3-14
Drivers & Utilities
What to Install ................................................................4-1
Module Driver Installation ..........................................4-1
Driver Installation ..........................................................4-2
Manual Driver Installation .........................................4-3
Updating/Reinstalling Individual Drivers ...................4-4
User Account Control (Win Vista) ..............................4-4
Windows Security Message .........................................4-4
New Hardware Found ..................................................4-4
Driver Installation Procedure .......................................4-5
Video (VGA) ..............................................................4-5
Audio ..........................................................................4-5
Modem ........................................................................ 4-5
LAN ............................................................................4 -5
TouchPad .................................................................... 4-5
ExpressCard/Card Reader ..........................................4-5
Hot Key ......................................................................4-6
AutoMail ..................................................................... 4-6
Wireless LAN Module ...............................................4-6
PC Camera Module ....................................................4-6
Bluetooth Module .......................................................4-6
Trusted Platform Module ...........................................4-6
Page 17
XV
Preface
Fingerprint Reader Module ........................................4-6
BIOS Utilities
Overview ........................................................................5-1
The Power-On Self Test (POST) ................................... 5-2
Failing the POST .........................................................5-3
Fatal Errors .................................................................5-3
Non-Fatal Errors .........................................................5-3
The Setup Program ........................................................5-4
Entering Setup .............................................................5-4
Setup Screens ...............................................................5-5
Main Menu .....................................................................5-6
System Time & Date (Main Menu) ...............................5-6
IDE Primary/Master (Main Menu) ................................5-7
IDE Secondary/Master (Main Menu) ............................5-7
System/Extended Memory: (Main Menu) .....................5-7
Advanced Menu .............................................................5-8
Reset Configuration Data: (Advanced Menu) ...............5-8
Local Bus IDE adapter: (Advanced Menu) ...................5-9
Boot-time Diagnostic Screen: (Advanced Menu) ..........5-9
Legacy USB Support: (Advanced Menu) ......................5-9
USB 2.0 Enable: ............................................................5-9
POST Beep Sound (Advanced Menu) ...........................5-9
Total Graphics Memory: (Advanced Menu) .................5-9
Security Menu ..............................................................5-10
Set Supervisor Password (Security Menu) ..................5-10
Password on boot: (Security Menu) .............................5-11
Fixed disk boot sector: (Security Menu) ......................5-11
TPM Support (Security Menu) ....................................5-11
TPM State ....................................................................5-12
TPM Function (TPM State) .........................................5-12
Boot Menu ...................................................................5-14
Exit Menu ....................................................................5-15
Upgrading The Computer
Overview ........................................................................6-1
When Not to Upgrade ..................................................6-2
Removing the Battery ....................................................6-3
Upgrading the Hard Disk Drive .....................................6-5
Upgrading the Optical (CD/DVD) Device ....................6-7
Upgrading the System Memory (RAM) ........................6-8
Upgrading the Processor ..............................................6-10
Modules & Options
Overview ........................................................................7-1
Wireless LAN Module ...................................................7-2
Intel WLAN Driver Installation .................................7-2
802.11 b/g WLAN Driver Installation ........................7-2
Connecting to a Wireless Network ..............................7-3
Windows Mobility Center ...........................................7 -6
Page 18
XVI
Preface
PC Camera Module ........................................................7-7
PC Camera Driver Installation ...................................7-7
PC Camera Audio Setup .............................................7-8
BisonCap ...................................................................7-10
Eliminating Screen Flicker .......................................7-11
Bluetooth Module .................................................... ....7-12
Bluetooth Driver Installation ....................................7-12
Bluetooth Local Area Connection ............................7-14
Security Modules (TPM & Fingerprint) ...................... 7-16
Trusted Platform Module .............................................7-17
Enabling & Activating TPM ....................................7-17
TPM Module Driver Installation ..............................7-19
Initializing TPM ........................................................7-20
Infineon Security Platform Settings Tool ..................7-23
Fingerprint Reader Module ..........................................7-24
Fingerprint Reader Driver Installation .....................7-24
User Enrollment ........................................................7-25
Troubleshooting
Overview ........................................................................8-1
Basic Hints and Tips ......................................................8-2
Backup and General Maintenance .................................8-3
Viruses ........................................................................... 8-4
Upgrading and Adding New Hardware/Software ..........8-5
Problems & Possible Solutions ......................................8-7
Interface (Ports & Jacks)
Overview ....................................................................... A-1
Notebook Ports and Jacks .............................................A-2
Built-In Microphone .....................................................A-2
Card Reader Port ...........................................................A-2
DC-In Jack ..................................................... ...............A-2
External Monitor (VGA) Port .......................................A-2
Headphone-Out Jack .....................................................A-2
Line-In Jack ..................................................................A-2
Microphone-In Jack ......................................................A-3
Mini-IEEE 1394 Port ....................................................A-3
RJ-11 Phone Jack ..........................................................A-3
RJ-45 LAN Jack ............................................................A-3
Security Lock Slot ........................................................A-3
S/PDIF-Out Jack ...........................................................A-4
USB 2.0/1.1 Ports .........................................................A-4
Intel Video Driver Controls
Intel Video Driver Installation ......................................B-1
Video .........................................................................B-1
Dynamic Video Memory Technology ........................B-1
Intel Graphics Properties ..............................................B-2
Scheme Options ..........................................................B-4
Display Devices ............................................................B-5
Attaching Other Displays ..............................................B-6
Page 19
XVII
Preface
Display Modes ..............................................................B-8
Specifications
Processor .......................................................................C-1
Core Logic ....................................................................C-1
Memory .........................................................................C-1
Security ......................................................................... C-2
BIOS ............................................................................. C-2
LCD .............................................................................. C-2
Video Adapter ...............................................................C-2
Storage .......................................................................... C-2
Audio ............................................................................ C-2
Keyboard & Pointing Device ........................................C-2
Interface ........................................................................ C-3
Card Reader ..................................................................C-3
ExpressCard Slot ..........................................................C-3
Communication ............................................................. C-3
Power Management ......................................................C-4
Power ............................................................................ C-4
Environmental Spec ......................................................C-4
Dimensions & Weight ..................................................C-4
Optional ........................................................................ C-4
Windows XP Information
DVD Regional Codes ...................................................D-2
Windows XP Start Menu & Control Panel ...................D-3
Audio Features ..............................................................D-4
Function Keys/Hot Keys ...............................................D-5
Application Hot Key .....................................................D-6
Video Features ..............................................................D-7
Dynamic Video Memory Technology ..........................D-7
Display & Graphics Properties .....................................D-8
Display Devices & Options .........................................D-10
Attaching Other Displays ............................................D-11
Power Management Features ......................................D-15
Power Schemes ...........................................................D-15
System Power Options.................................................D-16
Hibernate Mode vs. Shutdown ....................................D-16
Stand by Mode vs. Hibernate Mode ............................D-16
Stand by ......................................................................D-17
Hibernate .....................................................................D-17
Configuring the Power Buttons ..................................D-18
Battery Information .....................................................D-19
New Battery ................................................................D-19
Battery Life .................................................................D-19
Recharging the Battery with the AC/DC Adapter .......D-20
Proper handling of the Battery Pack ...........................D-21
Battery FAQ.................................................................D-22
Driver Installation .......................................................D-23
Installation Methods (Win XP) ...................................D-24
Page 20
XVIII
Preface
Updating/Reinstalling Individual Drivers....................D-25
Chipset (WinXP) ........................................................D-26
Video (WinXP) ...........................................................D-26
Audio (WinXP) ...........................................................D-26
Modem (WinXP) ........................................................D-26
LAN (WinXP) ............................................................D-26
TouchPad (WinXP) ....................................................D-27
ExpressCard/Card Reader (WinXP) ...........................D-27
Hot Key Utility (WinXP) ............................................D-27
Module Drivers............................................................D-27
Bluetooth Module .................................................... ...D-28
Bluetooth Driver Installation ......................................D-28
PC Camera Module .....................................................D-32
PC Camera Driver Installation ....................................D-32
PC Camera Audio Setup .............................................D-33
WLAN Module ...........................................................D-34
Intel WLAN Driver Installation ..................................D-34
802.11b/g USB WLAN Driver Installation ................ D-35
TPM Security Chip .....................................................D-36
TPM Utility Installation ..............................................D-36
Fingerprint Reader ...................................................... D-37
Fingerprint Reader Driver Installation ....................D-37
User Enrollment ..........................................................D-38
Page 21
Overview 1 - 1
Quick Start Guide
1
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:
Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, 7-in-1 card reader, ExpressCard/34/54), Function keys/Hot-Keys, Mail Checker, TouchPad & Mouse, Audio & Printer.
Chapter 3 The computer’s power saving options.
Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
Chapter 6 Instructions for upgrading your computer.
Chapter 7 A quick guide to the computer’s Wireless LAN, Bluetooth, PC Camera and Security modules (some of which may be optional depending on your purchase configuration).
Chapter 8 A troubleshooting guide.
Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external devices.
Appendix B Information on the Intel video driver controls.
Appendix C The computer’s specification.
• Appendix D Information on the Windows XP OS.
Page 22
1 - 2 Overview
Quick Start Guide
1
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on
page 6 - 1 in the User’s Manual. You may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then the information contained in this Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand every­thing the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a
as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
Notes
Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Page 23
Overview 1 - 3
Quick Start Guide
1
Model Differences
This notebook series includes two different model types. The models differ slightly in design style, and Model B supports a fingerprint reader module as an optional feature.
Not Included
Operating Systems (e.g. Windows Vista/Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the com­puter and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4 - 3. You will be unable to use most advanced controls until the necessary drivers and util­ities are properly installed. If your system hasn’t been properly configured (your service representative may have already done that for you), refer to “What to Install” on page 4 - 1 for installation instructions.
Ports and Jacks
See “Notebook Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your com­puter to communicate with external devices, connect to the internet etc.
Page 24
1 - 4 Overview
Quick Start Guide
1
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the following operating systems are sup­ported.
Table 1 - 1 - Operating Systems Supported
*Note: For information on the Windows XP OS (specifically power, video and driver information) see “Win-
dows XP Information” on page D - 1.
Operating System & Version Supported Note
*Windows XP (Home or Professional)
Windows Vista - SP1 (64-bit) Home Basic Edition
In order to run Windows Vista without limitations or decreased performance, your computer requires a minimum 1GB of system memory (RAM).
Windows Vista - SP1 (64-bit) Home Premium Edition
Windows Vista - SP1 (64-bit) Business/Enterprise/Ultimate Editions
Windows Vista Service Pack 1
Make sure you install Windows Vista Service Pack 1 (or a Windows Vista version which includes Service Pack 1) be­fore installing any driver s. Go to the Microsoft website for download details, or contact your service center.
Page 25
System Startup 1 - 5
Quick Start Guide
1
System Startup
1. Remove all packing materials.
2. Place the computer on a stable surface.
3. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
4. Attach the AC/DC adapter to the DC-In jack on the right of the computer, then plug the AC power cord into an
outlet, and connect the AC power cord to the AC/DC adapter.
5. Raise the lid/LCD to a comfortable viewing angle, and press the power button to turn the computer “on”.
6. Adjust the LCD panel to a comfortable viewing angle.
7. The LED Power & Communication indicators show the power and battery status of the computer, and give
notification of e-mail received.
Figure 1 - 1 - Computer with AC/DC Adapter Plugged-In
Shutdown
Note that you should always shut your computer down by choos­ing the Shut Down command from the Lock menu in Windows Vista. This will help prevent hard disk or system problems.
Page 26
1 - 6 System Map: LCD Panel Open - Model A
Quick Start Guide
1
System Map: LCD Panel Open - Model A
Figure 1 - 2
LCD Panel Open -
Model A
1. Optional Bu ilt-In PC Camera
2. LCD
3. Speakers
4. LED Status Indicators
5. Hot Key Buttons
6. Power Button
7. Keyboard
8. TouchPad and Buttons
9. LED Power & Communication Indicators
10. Built-In Microphone
11. Card Reader Module
2
5
1
7
8
4
6
9
3
10
Wireless Device
Operation Aboard Aircraft
The use of any portable electronic transmission devices aboard air­craft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard air­craft.
Use the key combinations to toggle power to the WLAN/Bluetooth modules, and check the LED indi­cator icon to see if the modules are powered on or not (see Table 1 - 3,
on page 1 - 8/Table 1 - 5, on page 1 - 10).
5
6
4
11
Page 27
System Map: LCD Panel Open - Model B 1 - 7
Quick Start Guide
1
System Map: LCD Panel Open - Model B
Figure 1 - 3
LCD Panel Open
Model B
1. Optional Built -In PC Camera
2. LCD
3. Speakers
4. LED Status Indicators
5. Hot Key Buttons
6. Power Button
7. Keyboard
8. TouchPad and Buttons
9. LED Power & Communication Indicators
10. Built-In Microphone
11. Fingerprint Reader Module (Optional)*
*Note: This model may have either a fingerprint module or card reader module, depend­ing on your purchase configu­ration.
2
5
1
7
8
4
6
9
3
10
Wireless Device
Operation Aboard Aircraft
The use of any portable electronic transmission devices aboard air­craft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard air­craft.
Use the key combinations to toggle power to the WLAN/Bluetooth modules, and check the LED indi­cator icon to see if the modules are powered on or not (see Table 1 - 3,
on page 1 - 8/Table 1 - 5, on page 1 - 10).
5
6
4
11
Page 28
1 - 8 LED Indicators
Quick Start Guide
1
LED Indicators
The two sets of LED indicators (LED Status Indica­tors and LED Power & Communication Indicators)
on the computer display helpful information about the current status of the computer.
Table 1 - 2 - LED Status Indicators
Table 1 - 3 - LED Power & Communication Indicators
Icon Color Description
Green
Number Lock Activated (to activate
press Fn & NumLk)
Green Caps Lock Activated
Green
Scroll Lock Activated (to activate
press Fn & ScrLk)
Icon Color Description
Green The Computer is On
Blinking
Green
The Computer is in Sleep Mode
Orange
The AC/DC Adapter is Plugged In
& the Computer is Powered Off
Orange
The AC/DC Adapter is Plugged In
& the Battery is Charging
Blinking
Orange
The Battery has Reached Critically
Low Power Status
Green The Battery is Fully Charged
Blinking
Green
New Mail Notification
(
Windows Vista Only)
Green Hard Disk Activity Green The WLAN Module is Powered On
Orange
The Bluetooth Module is Powered
On
Page 29
Quick Start Guide
Hot Key Buttons & Keyboard 1 - 9
1
Hot Key Buttons & Keyboard
These buttons give instant access to the default Inter­net browser and e-mail program, and to a user-defined application, with one quick button press. To use the “user-defined application Hot Key Button”, you must install the driver (see “Hot Key” on page 4 - 6). See
“Application Hot Key” on page 2 - 9 for configuration
instructions.
Table 1 - 4 - Hot Key Buttons
In addition to the basic function key combinations; vi­sual indicators (see Table 2 - 2, on page 2 - 8) are available when the hot key utility is installed.
The keyboard has an embedded numerical keypad for easy numeric data input, and features Function Keys to allow you to change operational features instantly (see
Table 1 - 5, on page 1 - 10 ).
Figure 1 - 4 - Keyboard
Hot Key Function
Activate the user specified application e.g.
Microsoft Word or Excel
Activate the Default E-Mail Program
Activate the Default Internet Browser
Play/Pause Key
Function Keys
NumLk & ScrLk Keys
Numerical Keypad
Other Keyboards
If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. T he system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work.
Page 30
Quick Start Guide
1 - 10 Function Keys
1
Function Keys
To use the function keys, press and hold the Fn key, then press the appropriate function key (F1 - F12 etc.).
Table 1 - 5 - Function Keys
Key Function Key Function
Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F7 Display Toggle
Fn Function Key Fn + F8 Decrease LCD Brightness
Fn + F1 TouchPad Toggle Fn + F9 Increase LCD Brightness
Fn + F2
Turn LCD Backlight Off
(Press a key to or use TouchPad to turn on)
Fn + F10 PC Camera Power T oggle
Fn + F3 Mute Toggle Fn + F11 Wireless Power Toggle Fn + F4 Sleep Toggle Fn + F12 Bluetooth Power Toggle Fn + F5 Decrease Audio Volume Fn + NumLk Number Lock Toggle Fn + F6 Increase Audio Volume Fn + ScrLk Scroll Lock Toggle
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special characters. These spe cial characters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that NumLk is on.
Page 31
System Map: Front & Rear Views 1 - 11
Quick Start Guide
1
System Map: Front & Rear Views
Figure 1 - 5
Front & Rear Views
1. LED Power & Communication Indicators
2. 7-in-1 Card Reader
3. External Monitor Port
4. Security Lock Slot
5. Battery
1
5
2
4
3
7-in-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) /
MS Pro (Memory Stick Pro) / MS Duo (requires PC adapter) /
Mini SD (requires PC adapter) / RS MMC (requires PC adapter)
Page 32
1 - 12 System Map: Left View
Quick Start Guide
1
System Map: Left View
Figure 1 - 6
Left View
1. RJ-45 LAN Jack
2. Vent/Fan Intake
3. 2 * USB 2.0 Ports
4. S/PDIF-Out Jack
5. Line-In Jack
6. Mini-IEEE 1394 Port
7. ExpressCard Slot (see page 2 - 7)
1
5
2
4
6
73
ExpressCard Slot
The ExpressCard Slot accepts either ExpressCard/34 or ExpressCard/54 formats.
Page 33
System Map: Right View 1 - 13
Quick Start Guide
1
System Map: Right View
Figure 1 - 7
Right View
1. Headphone-Out Jack
2. Microphone-In Jack
3. USB 2.0 Port
4. RJ-11 Phone Jack
5. Optical Device Drive Bay (for CD/ DVD Device - see page 2 - 3)
6. DC-In Jack
1
Changing DVD Regional Codes
Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM de-
vice to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code (see “DVD Regional Codes”
on page 2 - 5).
DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times. The fifth se­lection is permanent. This cannot be altered even if you change your operating system or you use the module in another computer.
4
5
6
32
CD Emergency Eject
If you need to manually eject a CD/DVD (e.g. due to an unexpected power inter­ruption) you may push the end of a straightened paper clip into the emer­gency eject hole. Do not use a sharp­ened pencil or similar object that may break and become lodged in the hole.
Media Warning
Don’t try to remove a floppy disk/CD/ DVD while the system is accessing it. This may cause the system to “crash”.
Page 34
1 - 14 System Map: Bottom View
Quick Start Guide
1
System Map: Bottom View
Figure 1 - 8
Bottom View
1. Vent/Fan Intake
2. Battery
3. Module Bay Cover
4. Hard Disk Cover
2
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial dis­charges. See “Battery Information” on page 3 - 10 for full instructions.
1
5
1
3
4
1
CPU
The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty.
Overheating
To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
1
Page 35
Windows Vista Start Menu & Control Panel 1 - 15
Quick Start Guide
1
Windows Vista Start Menu & Control Panel
Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features in Windows (e.g. power, video, network, audio etc.). Windows Vista provides basic controls for many of the fea- tures, however many new controls are added (or existing ones are enhanced) when you install the drivers listed in Table 4 - 1, on page 4 - 3. To see all controls it may be necessary to toggle to Classic View on.
Figure 1 - 9 - Start Menu & Control Panel
Click here to toggle Classic View
Page 36
1 - 16 Video Features
Quick Start Guide
1
Video Features
You can switch display devices, and configure display options, from the Display Settings control panel (in Per­sonalization) in Windows Vista as long as the appropriate Intel video driver is installed. For more detailed vid-
eo information see “Intel Video Driver Controls” on page B - 1.
To access Display Properties in Windows Vista:
1. Click Start, and click Control Panel (or point to Settings and click Control Panel).
2. Click Adjust screen resolution under the Appearance and Personalization menu (or double-click Personalization > Display Settings).
3. Move the slider to the preferred setting in Resolution: (Figure 1 - 10 on page 1 - 17).
4. Click the arrow, and scroll to the preferred setting In Colors: (Figure 1 - 10 on page 1 - 17).
5. Click Advan ced Sett ings (b utton) (Figure 1 - 10 on page 1 - 17) and click Intel(R) GMA Driver for mobile (tab).
6. Click Graphics Properties (button) (Figure 1 - 10 on page 1 - 17) to access the Intel GMA control panel (this control panel can also be accessed by double-clicking Intel(R) GMA Driver for mobile in Classic View).
7. The Intel GMA control panel can also be accessed by clicking the icon in the taskbar and selecting Graphics
Properties from the menu.
Display Devices & Options
Besides the built-in LCD, you can also use an external VGA monitor (CRT) or external Flat Panel Display connected to the external monitor port as your display device.
1
2
3
4
Page 37
Video Features 1 - 17
Quick Start Guide
1
Figure 1 - 10 - Display Properties Desktop
Table 1 - 6 - Display Options
Intel Display Mode Description
Single Mode One of the connected displays is used as the display device Intel(R) Dual Display Clone Mode Both connected displays output the same view and may be configured independently Extended Desktop Mode Both connected displays are treated as separate devices, and act as a virtual desktop
1
2
3
4
Page 38
1 - 18 Power Options
Quick Start Guide
1
Power Options
The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 15 ) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the power saver plan may have an affect on computer performance.
Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to create a new plan. Click Change Plan Settings and click Change advanced power settings to access further con- figuration options.
Pay attention to the instructions on battery care in “Battery Information” on page 3 - 10.
Figure 1 - 11 - Power Options
Note: Sleep is the default power saving state in Windows Vista
Page 39
Features & Components
Overview 2 - 1
2
Chapter 2: Features & Components
Overview
Read this chapter to learn more about the following main features and components of the computer:
•Hard Disk Drive
Optical (CD/DVD) Device
7-in-1 Card Reader
ExpressCard Slot
Function Keys/Hot Keys
Mail Checker
TouchPad and Buttons/Mouse
Audio Features
Adding a Printer
Page 40
Features & Components
2 - 2 Hard Disk Drive
2
Hard Disk Drive
The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm.
The hard disk is accessible from the bottom of your computer as seen below. For fur­ther details see “Upgrading the Hard Disk Drive” on page 6 - 5.
Power Safety
Before attempting to ac­cess any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the ma­chine is turned off. Also ensure that all peripher­al cables, including phone lines, are discon­nected from the comput­er.
Figure 2 - 1
Hard Disk Location
Hard Disk
Page 41
Features & Components
Optical (CD/DVD) Device 2 - 3
2
Optical (CD/DVD) Device
There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de­vice will depend on the module you purchased (see “Storage” on page C - 2). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 14).
Loading Discs
To insert a CD/DVD, press the open button and carefully place a CD/DVD onto the disc tray with label-side facing up (use just enough force for the disc to click onto the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you are ready to start. The busy indicator will light up while data is being accessed, or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupt­ed, insert an object such as a straightened paper clip into the emergency eject hole
to open the tray.
Sound Volume
Adjustment
How high the sound vol­ume can be set depends on the setting of the vol­ume control within Win- dows. Click the Volume icon on the taskbar to check the setting (see
“Audio Features” on page 2 - 12).
Figure 2 - 2
Optical Device
1
2
3
1
2
3
Page 42
Features & Components
2 - 4 Optical (CD/DVD) Device
2
Handling CDs or DVDs
Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Note the following:
Hold the CD or DVD by the edges; do not touch the surface of the disc.
Use a clean, soft, dry cloth to remove dust or fingerprints.
Do not write on the surface with a pen.
Do not attach paper or other materials to the surface of the disc.
Do not store or place the CD or DVD in high-temperature areas.
Do not use benzene, thinner, or other cleaners to clean the CD or DVD.
Do not bend the CD or DVD.
Do not drop or subject the CD or DVD to shock.
CD Emergency Eject
If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharp­ened pencil or similar object that may break and become lodged in the hole.
Disk Eject Warning
Don’t try to remove a CD/DVD while the sys­tem is accessing it. This may cause the system to “crash”.
Page 43
Features & Components
Optical (CD/DVD) Device 2 - 5
2
DVD Regional Codes
To change the DVD regional codes see “Changing DVD Regional Codes” on
page 1 - 13.
DVD Regional Coding
Region Geographical Location
1 USA, Canada
2
Western Europe, Japan, South
Africa, Middle East & Egypt
3
South-East Asia, Taiwan, South
Korea, The Philippines, Indonesia,
Hong Kong
4
South & Central America, Mexico,
Australia,
New Zealand
5
N Korea, Russia, Eastern Europe,
India & Most of Africa
6China
Table 2 - 1
DVD Regional Coding
Figure 2 - 3
DVD Regions
Page 44
Features & Components
2 - 6 7-in-1 Card Reader
2
7-in-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see “ExpressCard/Card Reader” on page 4 - 5).
Card Reader Cover
Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust get­ting in to the card read­er.
Figure 2 - 4
Front View
1. Card Reader
Front
1
Note: Model B computers may have either a fingerprint module OR card reader module, depending on your purchase configuration.
MMC (MultiMedia Card)
SD (Secure Digital)
MS (Memory Stick)
MS (Memory Stick Pro)
MS Duo (requires PC adapter)
Mini SD (requires PC adapter)
RS MMC (requires PC adapter)
Page 45
Features & Components
ExpressCard Slot 2 - 7
2
ExpressCard Slot
The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards).
ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Ex­press Card/54 and 34mm for the ExpressCard/34. Make sure you install the Card Reader driver (see “ExpressCard/Card Reader” on page 4 - 5).
Inserting and Removing ExpressCards
Align the ExpressCard with the slot and push it in until it locks into place.
To remove an ExpressCard, simply press the card to eject it (as pictured in the
generic figure below).
ExpressCard Slot
Cover
Make sure you keep the cover in the Express­Card slot when not in use. This will help pre­vent foreign objects and/ or dust getting in to the ExpressCard Slot.
Figure 2 - 5
Express Card Slot
Page 46
Features & Components
2 - 8 Function Keys/Hot Keys
2
Function Keys/Hot Keys
The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indica­tors (see the table below) are available when the hot key utility is installed (see “Hot
Key” on page 4 - 6). After installing the driver an icon will appear in the taskbar.
Fn
Keys
Function
Fn
Keys
Function
Fn + F1
TouchPad
Toggle
Fn +
F10
PC
Camera
Power Toggle
Fn + F3
Mute
Toggle
Fn +
F11
WLAN
Module
Power Toggle
Fn +
F5/F6
Volume
Decrease/
Increase
Fn +
F12
Bluetooth
Module
Power Toggle
Fn +
F8/F9
Brightness Decrease/
Increase
Hot Key Driver
Double-click the icon to bring up the configu­ration menu to define which application to open when the applica­tion hot key button is pressed (see “Appli-
cation Hot Key” on page 2 - 9).
If you click the close icon
, run the program from the file location (C:\Program Files (x86)\Hotkey_Driver\Ho tkeyDriver.exe).
Table 2 - 2
Function Key
Combo Indicators
Page 47
Features & Components
Function Keys/Hot Keys 2 - 9
2
Application Hot Key
To configure a program to open when the application hot key button is pressed (follow the instructions below.
1. Double-click the hot key driver icon in the taskbar.
2. Click Launch user specified application (button) .
3. An Open dialog box will appear on the screen.
4. Browse to the directory where the desired application.exe program exists.
5. Double-Click on the program file or choose Open, and click OK (button).
6. Press the application hot key button to open the program (as long as the hot key driver is running in the taskbar).
Application.exe
You will need to locate the actual application executable (.exe) file, not just the shortcut. To find the application right­click its shortcut on the desktop and click Prop-
erties. Click the short­cut (tab) and see where
the executable file is lo­cated by clicking the
Open File Location
(button).
Figure 2 - 6
Hot Key Driver
Page 48
Features & Components
2 - 10 Mail Checker
2
Mail Checker
After you have installed the driver for the Mail Checker program (see “AutoMail”
on page 4 - 6) you may then configure it to give you notification when you receive
new mail (you may configure a Wave for audible notification and the Mail LED will give visual notification when mail is received). You must be online to receive this notification (note that this program only supports the POP3 protocol), and the default mail program does not need to be open.
Double-click the Mail Check icon in the taskbar to run the program (click Hide to close the window but keep the program running). You may then configure the op­tions for your mail server, user name, password and method(s) of notification. Click Save to retain the setting information.
Note
Check with your Internet Service Provider, net­work administrator or Mail Service provider for details on what to put on these pages.
If you click the close icon
, run the program from the file location (C:\Program Files (x86)\Check_Email\Mail Check.exe).
Figure 2 - 7
Mail Check Account
Setup and Options
Page 49
Features & Components
TouchPad and Buttons/Mouse 2 - 11
2
TouchPad and Buttons/Mouse
The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Configuring the TouchPad and Buttons
Once you have installed the TouchPad driver configure the functions by double­clicking the TouchPad driver icon in the taskbar. Alternatively click Start and click Control Panel, and then double-click the Mouse icon (Hardware and Sound). The TouchPad may be toggled on/off by means of the Fn + F1 key combi­nation.
Mouse Driver
If you are using an exter­nal mouse your operat­ing system may be able to auto-configure your mouse during its instal­lation or only enable its basic functions. Be sure to check the device’s user documentation for details.
Figure 2 - 8
Mouse Properties
Page 50
Features & Components
2 - 12 Audio Features
2
Audio Features
You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ control panel (right-click the taskbar icon to bring up an audio menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination.
Sound Volume
Adjustment
The sound volume level is set using the volume control within Windows (and the volume func­tion keys on the comput­er). Click the volume icon in the taskbar to check the setting.
Figure 2 - 9
Realtek Audio
Manager
Right-click the icon to access the menu above.
Page 51
Features & Components
Adding a Printer 2 - 13
2
Adding a Printer
The most commonly used peripheral is a printer. The following conventions will help you to add a printer, however it is always best to refer to the printer manual for specific instructions and configuration options.
USB Printer
Most current printers have a USB interface connection. You may use any one of the ports to connect the printer.
Install Instructions:
1. Set up the printer according to its instruction s (unp acking, paper tray, toner/ink car­tridge etc.).
2. Turn ON the computer.
3. Turn ON the printer.
4. Connect the printer’s USB cable to one of the USB ports on the computer.
5. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions.
Parallel Printer
This is still a very common type of printer. The install instructions are in the sidebar, however you will need to purchase a parallel to USB converter.
Parallel Printer
After setting up the print­er attach the parallel ca­ble to the printer.
Connect the printer’s parallel cable to the Par­allel to USB converter, and then plug the con­verter into the USB port.
Turn ON the printer, then turn ON the com­puter.
Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen in­structions.
Page 52
Features & Components
2-14
2
Page 53
Power Management
Overview 3 - 1
3
Chapter 3: Power Management
Overview
To conserve power, especially when using the battery, your computer power man­agement conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
This chapter covers:
The Power Sources
Turning on the Computer
Power Plans
Power-Saving States
Configuring the Power Buttons
Battery Information
The computer uses enhanced power saving techniques to give the operating system (OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user set­tings and information from applications.
OS Note
Power management functions will vary slight­ly depending on your operating system. For more information it is best to refer to the user’s manual of your operat­ing system.
(Note: All pictures used on the following pages are from the Windows Vista OS.)
Page 54
Power Management
3 - 2 The Power Sources
3
The Power Sources
The computer can be powered by either an AC/DC adapter or a battery pack.
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components (see page C - 4).
1. Attach the AC/DC adapter to the DC-In jack at the rear of the computer.
2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the AC/DC adapter.
3. Raise the lid/LCD to a comfortable viewing angle.
4. Press the power button to turn “On”.
Battery
The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before recharging (see “How do I completely discharge the battery?”
on page 3 - 14).
We recommend that you do not remove the battery. For more information on the bat­tery, please refer to “Battery Information” on page 3 - 10.
Page 55
Power Management
Turning on the Computer 3 - 3
3
Turning on the Computer
Now you are ready to begin using your computer. To turn it on simply press the pow­er button on the front panel.
When the computer is on, you can use the power button as a Sleep/Hibernate hot­key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down). Use Power Op- tions (Hardware and Sound menu) control panel in Windows Vista to configure this feature.
Shut Down
Note that you should al­ways shut your comput­er down by choosing the Shut Down command from the Lock Button
Menu in Windows Vis- ta. This will help prevent
hard disk or system problems.
Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the pow­er button for 4 seconds, or longer, to force the system to turn itself off.
Power Button Sleep
Sleep is the default power mode when the power button is pressed for less than 4 seconds. You may configure the options for the power button from the Power Options (Hardware and Sound menu) control panel in Windows Vista (see your OS’s documentation, or
“Configuring the Power Buttons” on page 3 - 8 for details).
Page 56
Power Management
3 - 4 Power Plans
3
Power Plans
The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity.
Click Change plan settings and then click Change advanced power settings to ac­cess further configuration options in Advanced Settings.
Resuming Operation
See Table 3 - 1, on
page 3 - 9 for informa-
tion on how to resume from a power-saving state.
Password
It is recommended that you enable a password on system resume in or­der to protect your data.
Figure 3 - 1
Power Plan
Advanced Settings
Page 57
Power Management
Power Plans3-5
3
Each Windows Power Plan will also adjust the processor performance of your ma­chine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).
Choose High performance for maximum performance when the computer is pow­ered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) pow­ered.
Figure 3 - 2
Power Plans
Page 58
Power Management
3 - 6 Power-Saving States
3
Power-Saving States
You can use power-saving states to stop the computer’s operation and restart where you left off. Sleep is the default power-saving state in Windows Vista.
Earlier versions of Windows used Stand By and Hibernate as system power-saving states. Windows Vista combines the features of Stand By and Hibernate into the de­fault Sleep power-saving state.
Sleep
In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
The PC wakes from Sleep within seconds and will return you to where you last left off (what was on your desktop) without reopening the application(s) and file(s) you last used.
If your mobile PC in Sleep is running on battery power the system will use only a minimum amount of power. After an extended period the system will save all the information to the hard disk and shut the computer do wn before the battery becomes depleted.
Power Button
The Power Button in the Start Menu (in Classic View use the Shut Down button ) can be used to send the computer into a power­saving state.
Sleep Mode &
Mobile PC Battery
A mobile PC in Sleep uses very little battery power.
After an extended peri­od of time the computer will save any open docu­ments and applications to hard disk.
Page 59
Power Management
Power-Saving States 3 - 7
3
Hibernate
Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hi- bernate will also return you to where you last left off within seconds. You should put your mobile PC into Hibernate if you will not use the computer for a period of time, and will not have the chance to charge the battery.
Shut Down
You should shut down the computer if you plan to install new hardware (don’t for­get to remove the battery and follow all the safety instructions in Chapter 6), plan to be away from the computer for several days, or you do not need it to wake up and run a scheduled task. Returning to full operation from shut down takes longer than from Sleep or Hibernate.
Figure 3 - 3
Lock Button Menu
Page 60
Power Management
3 - 8 Configuring the Power Buttons
3
Configuring the Power Buttons
The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state.
Password Protection
It is recommended that you enable a password on wake up in order to protect your data.
However you can dis­able this setting from the Power Options menu by clicking Require a
password on wakeup
in the left menu, and se­lecting the options (click
Change settings that are currently unavail­able).
Figure 3 - 4
Power Options
Define Power
Buttons
Page 61
Power Management
Configuring the Power Buttons 3 - 9
3
Resuming Operation
You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo).
Power Status
Icon Color
To Resume
Power Off Off Press the Power Button
Sleep Blinking Green
Press the Power Button
Press the Sleep Button (Fn + F4 Key Combo)
Hibernate
Off (battery)
Press the Power Button
Orange (AC/DC adapter)
Display Turned Off Green Press a Key or Move the Mouse/Touchpad
Closing the Lid
If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Table 3 - 1
Resuming Operation
Power Button
When the computer is on, you can use the power button as a Sleep/Hibernate hot-key but­ton when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force shut the computer to shut down).
Page 62
Power Management
3 - 10 Battery Information
3
Battery Information
Please follow these simple guidelines to get the best use out of your battery.
Battery Power
Your computer’s battery power is dependent upon many factors, including the pro­grams you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Advanced Settings (see Figure 3 - 1 on page 3 - 4).
Click the battery icon in the taskbar to see the current battery level and charge status.
Low Battery
Warning
When the battery is criti­cally low, immediately connect the AC/DC adapter to the computer or save your work, oth­erwise, the unsaved data will be lost when the power is depleted.
Figure 3 - 5
Battery Icon
(Taskbar) & Battery
Advanced Settings
Page 63
Power Management
Conserving Battery Power 3 - 11
3
Conserving Battery Power
•Use a power plan that conserves power (e.g Power saver), however note that
this may have an affect on computer performance.
Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter.
Reduce the amount of time before the display is turned off.
Close wireless, Bluetooth, modem or communication applications when they are not being used.
Disconnect/remove any unnecessary external devices e.g. USB devices, ExpressCards etc.
Windows Mobility
Center
The Windows Mobility Center control panel pro-
vides an easy point of ac­cess for information on battery status, power plans used and wireless device status etc.
Figure 3 - 6
Windows Mobility
Center
Page 64
Power Management
3 - 12 Battery Life
3
Battery Life
Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days.
We recommend that you do not remove the battery yourself. If you do need to re­move the battery for any reason see “Removing the Battery” on page 6 - 3.
New Battery
Always completely discharge, then fully charge, a new battery (see “Battery FAQ”
on page 3 - 14 for instructions on how to do this).
Recharging the Battery with the AC/DC Adapter
The battery pack automatically recharges when the AC/DC adapter is attached and plugged into an electrical outlet. If the computer is powered on, and in use, it will take several hours to fully recharge the battery. When the computer is turned off but plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-
tors” on page 1 - 8 for information on the battery charge status, and to “Battery In­formation” on page 3 - 10 for more information on how to maintain and properly
recharge the battery pack.)
Page 65
Power Management
Battery Life3-13
3
Proper handling of the Battery Pack
DO NOT disassemble the battery pack under any circumstances
DO NOT expose the battery to fire or high temperatures, it may explode
DO NOT connect the metal terminals (+, -) to each other
Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent ou t of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center. If the battery has been d roppe d we do not recommend using it any further, as even if the computer continues to work with a dam­aged battery in place, it may cause circuit damage, which may possibly result in fire . It is recommended that you replace your computer battery every two years.
Caution
Danger of explosion if battery is incorrectly re­placed.
Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s in­structions.
Page 66
Power Management
3 - 14 Battery Life
3
Battery FAQ
How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
1. Save and close all files and applications.
2. Create a power plan for discharging the battery and set all the options to Never.
3. Click Change plan settings (after saving it) and click Change advanced power settings.
Figure 3 - 7
Power Plan Create
Page 67
Power Management
Battery Life3-15
3
4. Scroll down to Battery and click + to expand the ba ttery options.
5. Choose the options below (click Yes if a warning appears):
Low battery levels = 0%
Critical battery Levels = 0%
Low battery action = Do Nothing
Critical battery action (On battery) = Shut Down
Critical battery action (Plugged in) = Do Nothing
Figure 3 - 8
Power Options
Advanced Settings -
Battery
Page 68
Power Management
3 - 16 Battery Life
3
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes from orange to green.
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Page 69
Drivers & Utilities
What to Install 4 - 1
4
Chapter 4: Drivers & Utilities
This chapter deals with installing the drivers and utili­ties essential to the operation or improvement of some of the computer’s subsystems. The system takes ad­vantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-config­ured with an appropriate driver or utility during oper­ating system installation. Instead, you need to manually install some system-required drivers and utilities.
What to Install
The Device Drivers & Utilities + User’s Manual CD­ROM contains the drivers and utilities necessary for
the proper operation of the computer. Table 4 - 1, on
page 4 - 3 lists what you need to install manually ac-
cording to your choice of the operating system, and it is very important that the drivers are installed in the order indicated.
Module Driver Installation
The procedures for installing drivers for the Wireless LAN, PC Camera, Bluetooth and Security modules
are provided in “Modules & Options” on page 7 - 1. Make sure that the drivers are installed in the order in­dicated in Table 4 - 1, on page 4 - 3. Only install driv­ers for modules included in your purchase option.
Page 70
Drivers & Utilities
4 - 2 Driver Installation
4
Driver Installation
Insert the Device Drivers & Utilities + User’s Manual CD-ROM and click Install Drivers (button)/Option
Drivers (button).
Figure 4 - 1 - Drivers Installer Screen 1
1. Check the driver installation order from Table 4 - 1,
on page 4 - 3 (the dri ve r s mus t be installed in
this order) which is the same as that listed in the
Drivers Installer menu below.
2. Click to select the driver you wish to install, after installing each driver it will become grayed out (if you need to reinstall any driver, click the Unlock button).
3. Follow the instructions for each individual driver installation procedure as listed on the following pages.
Figure 4 - 2 - Drivers Installer Screen 2
If you have included the Fingerprint module option (Model B computers only) in your purchase configuration, then this driver will replace the CardReader Driver here.
Page 71
Drivers & Utilities
Driver Installation 4 - 3
4
Manual Driver Installation
Click the Browse CD button in the Drivers Installer application and browse to the executable file in the appropriate driver folder.
Table 4 - 1 - Driver Installation
Driver Page
Video (VGA)
Page 4 - 5
Audio
Page 4 - 5
Modem
Page 4 - 5
LAN
Page 4 - 5
TouchPad
Page 4 - 5
ExpressCard/Card Reader
Page 4 - 5
Hot Key
Page 4 - 6
AutoMail
Page 4 - 6
Wireless LAN Module
Page 7 - 2
PC Camera Module
Page 7 - 7
Bluetooth Module
Page 7 - 12
Trusted Platform Module
Page 7 - 19
Fingerprint Reader Module
Page 7 - 24
Page 72
Drivers & Utilities
4 - 4 Driver Installation
4
Updating/Reinstalling Individual Drivers
If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Pro- grams > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be nec­essary to restart the computer). Reinstall the driver as outlined in this chapter.
If the driver is not listed in the Programs and Fea- tures menu:
1. Click Start, and click Control Panel (or point to Settings and click Control Panel).
2. Double-click Device Manager (Hardware and Sound > Device Manager).
3. Double-click the device you wish to update/reinstall the driver for (you may need to click “+” to expand the selection).
4. Click Driver (tab) and click the Update Driver or
Uninstall button and follow the on screen prompts.
User Account Control (Win Vista)
If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Allow, and follow the installation procedure as direct­ed.
Windows Security Message
If you receive a Windows security message as part of the driver installation process. Just click “Install this driver software anyway” or Install to continue the in- stallation procedure.
You will receive this message in cases where the driv­er has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.
New Hardware Found
If you see the message “New Hardware Found” (Found New Hardware Wizard) during the installa­tion procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure.
Page 73
Drivers & Utilities
Driver Installation 4 - 5
4
Driver Installation Procedure
Video (VGA)
1. Click 1.Install VGA Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer.
Audio
1. Click 2.Install Audio Driver > Yes.
2. Click Next.
3. Click Finish to restart the computer.
Modem
1. Click 3.Install Modem Driver > Yes.
2. Click OK.
3. The modem is ready for dial-up configuration.
LAN
1. Click 4.Install Lan Driver > Yes.
2. Click Next > Install.
3. Click Finish.
TouchPad
1. Click 5.Install T o uchPad Driver > Yes.
2. Click Next > Finish.
3. Click Restart Now to restart the computer.
4. You may then configure your TouchPad as out-
lined in “TouchPad and Buttons/Mouse” on
page 2 - 11.
ExpressCard/Card Reader
1. Click 6.Install CardReader Driver > Yes.
2. Click Next > Next.
3. Click Finish to restart the computer.
Modem Country Selection
Go to the Phone and Modem Options con trol panel (Hard­ware and Sound) and make sure the modem country selection
is appropriate for you.
Page 74
Drivers & Utilities
4 - 6 Driver Installation
4
Hot Key
1. Click 7.Install HOTKEY Driver > Yes.
2. Click Next > Install.
3. Click Finish > Finish to restart your computer.
4. See “Function Keys/Hot Keys” on page 2 - 8 for configuration instructions.
AutoMail
1. Insert the
Device Drivers & Utilities + User’s
Manual CD-ROM
and click
Browse CD
(button).
2. Double-click to open the following folders
Driv-
ers > Automail
(X:\Drivers\Automail\setup.exe).
3. Double-click Setup.exe.
4. Click Next > Install.
5. Click Finish > Finish to restart your computer.
Wireless LAN Module
See the introduction in “Wireless LAN Module” on
page 7 - 2, and check the installation procedure.
PC Camera Module
See the introduction in “PC Camera Module” on
page 7 - 7, and check the installation procedure.
Bluetooth Module
See the introduction in “Bluetooth Module” on
page 7 - 12, and check the installation procedure.
Trusted Platform Module
See the introduction in “Trusted Platform Module”
on page 7 - 17, and check the installation procedure.
Fingerprint Reader Module
See the introduction in “Fingerprint Reader Module”
on page 7 - 24, and check the installation procedure.
Page 75
BIOS Utilities
Overview 5 - 1
5
Chapter 5: BIOS Utilities
Overview
This chapter gives a brief introduction to the computer’s built-in software:
Diagnostics: The POST (Power-On Self Test)
Configuration: The Setup utility
If your computer has never been set up, or you are mak ing important chan ges to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the set­tings you find and any changes you make. This information could be useful if your system ever needs servicing.
There is one general rule: Don’t make any changes unless you are sure of what you are doing. Many of the settings are required by the system, and changing them could cause it to become unstable or worse. If you have any doubts, consult your service representative.
BIOS Settings
Warning
Incorrect settings can cause your system to malfunction. To correct mistakes, return to Set-
up and restore the Set­up Defaults with <F9>.
Page 76
BIOS Utilities
5 - 2 The Power-On Self Test (POST)
5
The Power-On Self Test (POST)
Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).
As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup.
If there are no problems, the Setup prompt will disappear and the system will load the operating system. Once that starts, you can’t get into Setup without rebooting.
POST Screen
1.BIOS information
2.CPU type
3.Memory status
4.Enter Setup prompt appears only during
POST
Note:
The
POST
screen as pictured right is for guideline purposes only. The
POST
screen on your computer may ap­pear slightly different. If you disable the
Boot-
time Diagnostic Screen
, the POST screen will not appear.
Figure 5 - 1
POST Screen
Phoenix TrustedCore(tm) NB Copyright 1985-2006 Phoenix Technologies Ltd. All Rights Reserved Bios Revision: ******** KBC/EC Firmware Revision: ********
CPU=1Processors Detected, Cores per Processor = 2 Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz TCG is enabled 1015M System RAM Passed 4096 KB L2 Cache System BIOS shadowed Video BIOS shadowed Fixed Disk 0: FUJITSU MHV2100BH PL ATAPI CD-ROM: Optiarc CD-RW CRX880A Mouse intialized
Press <F2> to enter SETUP
1
2
3
4
Page 77
BIOS Utilities
The Power-On Self Test (POST) 5 - 3
5
Failing the POST
Errors can be detected during the POST. There are two categories, “fatal” and “non­fatal”.
Fatal Errors
These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.
Non-Fatal Errors
This kind of error still allows you to boot. You will get a message identifying the problem (make a note of this message!) followed by the prompt:
Press <F1> to resume
<F2> to enter Setup
Press F1 to see if the boot process can continue. It may work, without the correct configuration.
Press F2 to run the Setup program and try to correct the problem. If you still get an error message after you change the setting, or if the “cure” seems even worse, call for help.
Page 78
BIOS Utilities
5 - 4 The Setup Program
5
The Setup Program
The Phoenix Setup program tells the system how to configure itself and manage ba- sic features and subsystems (e.g. port configuration).
Entering Setup
To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
If the computer is already on, reboot using the Ctrl + Alt + Delete combination and then hold down F2 when prompted. The Setup main menu will appear.
Page 79
BIOS Utilities
The Setup Program 5 - 5
5
Setup Screens
The following pages contain additional advice on portions of the Setup.
Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup.
Instructions on how to navigate each screen are in the box along the bottom of the screen. If these tools are confusing, press F1 to call up a General Help screen, and then use the arrow keys to scroll up or down the page.
The Item Specific Help on the right side of each screen explains the highlighted item and has useful messages about its options.
If you see an arrow next to an item, press Enter to go to a sub-menu on that sub­ject. The sub-menu screen that appears has a similar layout, but the Enter key may execute a command.
Setup Menus
The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configura­tion appropriate for your model and options.
TPM State
Note that the TPM State menu will only appear if you enable TPM Sup- port from the Security menu.
Page 80
BIOS Utilities
5-6Main Menu
5
Main Menu
System Time & Date (Main Menu)
The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
Figure 5 - 2
Main Menu
Main Advanced Security Boot Exit
F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
<Tab>, <Shift Tab>, or <Enter> selects field.
Main
BIOS Revision: *********
System Time:
[22:12:05]
System Date: [04/17/2007]
IDE Primary/Master [FUJITSU MHV2100BH PL-(S1)]
IDE Secondary/Master [Optiarc CD-RW CRX880A-(SM]
System Memory: 640 KB Extended Memory: 1038336 KB
Phoenix TrustedCore(tm) Setup Utility
Page 81
BIOS Utilities
Main Menu 5 - 7
5
IDE Primary/Master (Main Menu)
Pressing Enter opens the sub-menu to show the configuration of a HDD on the com- puter’s IDE Primary/Master Channel. Use the Auto (Type:) setting to have the items configured automatically for you.
IDE Secondary/Master (Main Menu)
Pressing Enter opens the sub-menu to show the configuration of an optical Device on the computer’s IDE Channel 1. Use the Auto (Type:) setting to have the items configured automatically for you.
System/Extended Memory: (Main Menu)
This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
Page 82
BIOS Utilities
5 - 8 Advanced Menu
5
Advanced Menu
Reset Configuration Data: (Advanced Menu)
This item is set to No as default. You can change the setting to Yes if you have in­stalled a new add-on which has reconfigured the system, resulting in such a serious system conflict that the operating system is unable to boot.
Figure 5 - 3
Advanced Menu
Main Advanced Security Boot Exit
F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
Select 'Yes' if you want to clear the Extended System Configuration Data (ESCD) area.
Advanced
Reset Configuration Data: [No]
Local Bus IDE Adapter: [Both]
Boot-time Diagnostic Screen: [Enabled] Legacy USB Support: [Enabled] USB 2.0 Enable: [Enabled] POST Beep Sound [Disabled]
Total Graphics Memory: [128MB]
Phoenix TrustedCore(tm) Setup Utility
Page 83
BIOS Utilities
Advanced Menu 5 - 9
5
Local Bus IDE adapter: (Advanced Menu)
This item allows you to configure the IDE bus which controls the hard disk and op­tical devices. It is set to “Both” by default.
Boot-time Diagnostic Screen: (Advanced Menu)
Use this menu item to enable/disable the Boot-time Diagnostic Screen.
Legacy USB Support: (Advanced Menu)
Use this menu item to enable/disable the support for Legacy Universal Serial Bus.
USB 2.0 Enable:
This menu item can be used to enable/disable support for USB 2.0.
POST Beep Sound (Advanced Menu)
Use this menu item to enable/disable the beep as the computer starts up.
Total Graphics Memory: (Advanced Menu)
Use this menu item to set the amount of system memory to be allocated for use by the internal graphics device. The default memory size allocated is 128MB, and this may be adjusted to 64MB or 256MB (by pressing the spacebar to adjust) if required.
Page 84
BIOS Utilities
5 - 10 Security Menu
5
Security Menu
Set Supervisor Password (Security Menu)
You can set a password for access to the PhoenixBIOS Setup Utility. This will not affect access to the computer OS, (only the PhoenixBIOS Setup Utility).
Security Menu
The changes you make here affect the access to the Setup utility itself, and also access to your ma­chine as it boots up af­ter you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS.
Figure 5 - 4
Security Menu
Main Advanced SSeeccuurriittyyBoot Exit
F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
Enable Trusted Platform Module support
Security
Supervisor Password Is: Clear
Set Supervisor Password [Enter] Password on boot: [
D
i
sable
d
]
Fixed disk boot sector: [Normal]
TPM Support [Disabled]
Phoenix TrustedCore(tm) Setup Utility
Page 85
BIOS Utilities
Security Menu 5 - 11
5
Password on boot: (Security Menu)
Specify whether or not a password should be entered to boot the computer (you may only set a password on boot if a supervisor password is enabled). If “Enabled is selected, only users who enter a correct password can boot the system (see the warning in the sidebar). The default setting is “Disabled”.
Note: To clear existing passwords press Enter and type the existing password, then
press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance.
Fixed disk boot sector: (Security Menu)
If you choose “Write-Protect” this will protect against viruses being written to the hard disk boot sector (this is not a substitute for installing an anti-virus program - see
“Viruses” on page 8 - 4).
TPM Support (Security Menu)
Enable TPM Support from this menu, and the TPM State menu will then appear (see “TPM State” on page 5 - 12). Note: If you disable TPM Support then your TPM information may be erased altogether. You should only disable TPM support when you need to clear the TPM information. The default setting is “Disabled”.
Password Warning
If you set a boot pass­word (Password on boot is “Enabled“), NEVER forget your password.
The consequences of this could be serious. If you cannot remember your boot password you must contact your ven­dor and you may lose all of the information on your hard disk.
TPM Password
Note that you should set a supervisor password in the BIOS to protect the TPM information from being tampered with by unauthorized us­ers.
Page 86
BIOS Utilities
5 - 12 TPM State
5
TPM State
TPM Function (TPM State)
This menu allows you to set the level of TPM functionality. You can enable/disable the TPM function altogether, or clear all existing TPM information.
Note: If you clear all TPM information it will be erased altogether and the informa­tion will need to be reconfigured.
Main Advanced Security Boot Exit
F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
Changes TPM State
TPM State
Current TPM State: Enabled and Deactivated
TPM Function [No Change ]
No Change
Enable & Activate Deactivate & Disable Clear
Phoenix TrustedCore(tm) Setup Utility
TPM State Menu
To access this menu you must first enable TPM support from the security menu (see page 5 - 11).
Password Protection
Note that you should set a supervisor password in the BIOS to protect the TPM information from being tampered with by unauthorized us­ers.
Figure 5 - 5
TPM State
Page 87
BIOS Utilities
TPM State 5 - 13
5
If you have made any changes to the TPM State you will be asked to execute or reject the changes made after you have saved and exited the BIOS. Highlight the required option (it will be white), and then press Enter to save it.
F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
Physical Presence operations
TPM configuration change was requested to State: Clear
WARNING!!! Clearing erases information stored on the TPM. You will lose all created keys and access to data encrypted by these keys. to
Reject
Execute
Phoenix TrustedCore(tm) Setup Utility
Execute Physical Presence operations and exit
Figure 5 - 6
Physical Presence
Operations
Page 88
BIOS Utilities
5 - 14 Boot Menu
5
Boot Menu
When you turn the computer on it will look for an operating system (e.g. Windows Vista) from the devices listed in this menu, and in this priority order. If it cannot
find the operating system on that device, it will try to load it from the next device in the order specified in the Boot priority order. Item specific help on the right is available to help you move devices up and down the order.
Figure 5 - 7
Boot Menu
Phoenix TrustedCore(tm) Setup Utility
F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
Keys used to view or configure devices: Up and Down arrows select a device. <+> and <-> moves the device up or down. <x> exclude or include the device to boot.
Boot priority order:
1: USB FDC:
2: IDE CD: Optiarc CD-RW CRX880A-(SM) 3: IDE HDD: FUJITSU MHV2100BH PL-(S1) 4: USB HDD: 5: PCI BEV: Realtek Boot Agent 6: 7: 8:
Excluded from boot order:
: USB KEY: : USB CDROM: : USB ZIP: : 1394 CDROM:
Main Advanced Security
Boot
Exit
Page 89
BIOS Utilities
Exit Menu 5 - 15
5
Exit Menu
Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Set- up defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
Figure 5 - 8
Exit Menu
F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
Exit System Setup and save your changes to CMOS.
Exit Saving Changes
Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes
Main Advanced Security Boot
Exit
Phoenix TrustedCore(tm) Setup Utility
Page 90
BIOS Utilities
5-16
5
Page 91
Upgrading The Computer
Overview 6 - 1
6
Chapter 6: Upgrading The Computer
Overview
This chapter contains information on upgrading the computer. Follow the steps out­lined to make the desired upgrades. If you have any trouble or problems you can con­tact your service representative for further help. Before you begin you will need:
A small crosshead or Phillips screwdriver
A small regular slotted (flathead) screwdriver
An antistatic wrist strap Before working with the internal components you will need to wear an antistatic
wrist strap to ground yourself because static electricity may damage the compo­nents.
The chapter includes:
Removing the Battery
Upgrading the Hard Disk Drive
Upgrading the Optical (CD/DVD) Device
Upgrading the System Memory (RAM)
Please make sure that you review each procedure before you perform it.
Warranty Warning
Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.
Page 92
Upgrading The Computer
6 - 2 Overview
6
When Not to Upgrade
These procedures involve opening the system’s case, adding and sometimes replac­ing parts.
You should not perform any of these upgrades if:
Your system is still under warranty or a service contract
You don’t have all the necessary equipment
You’re not in the correct environment
You doubt your abilities
Under any of these conditions, contact your service representative to purchase or re­place the component(s).
Power Safety
Warning
Before you undertake any upgrade proce­dures, make sure that you have turned off the power, and disconnect­ed all peripherals and cables (including tele­phone lines). It is advis­able to also remove your battery in order to pre­vent accidentally turning the machine on.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before turning the computer on.
Page 93
Upgrading The Computer
Removing the Battery 6 - 3
6
Removing the Battery
If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery.
1. Turn the computer off, and turn it over.
2. Slide the latch in the direction of the arrow, and hold it in place.
3. Slide the battery in the direction of the arrow .
Warranty Warning
Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.
Figure 6 - 1
Battery Latch
1
2
2
1
1
Page 94
Upgrading The Computer
6 - 4 Removing the Battery
6
4. Lift the battery up and out in the direction of the arrow .
5. Insert the battery by pushing it straight down into the battery bay (it will only fit one way, don’t force it).
6. Make sure the battery is sitting flat in the slot, and then slide the battery in the direction of the arrow until the lock clicks into place.
Figure 6 - 2
Battery Removal
Figure 6 - 3
Battery Insertion
3
3
4
4
Page 95
Upgrading The Computer
Upgrading the Hard Disk Drive 6 - 5
6
Upgrading the Hard Disk Drive
The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5mm (h) (see “Storage” on page C - 2). Follow your operating system’s installation instructions, and install all necessary drivers and util­ities (as outlined in “Driver Installation” on page 4 - 2), when setting up a new hard disk.
1. Turn off the computer, and turn it over and remove the battery.
2. Locate the hard disk bay cover and remove screws & .
3. Remove the hard disk cover .
HDD System
Warning
New HDD’s are blank. Be­fore you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to in­stall your operating system and programs. If you have access to the in­ternet, download the latest application and hardware driver updates for the oper­ating system you plan to in­stall. Copy these to a removable medium.
Figure 6 - 4
Hard Disk Bay
Cover Removal
1
2
2
1
3
3
Page 96
Upgrading The Computer
6 - 6 Upgrading the Hard Disk Drive
6
4. Pull the tab to slide the hard disk and case assembly in the direction of arrow .
5. Lift the hard disk and case assembly out of the bay in the direction of arrow .
6. Remove screws - to release the hard disk from the case , and reverse the process to install any new hard disk.
4
5
6 7 8 9
Figure 6 - 5
Hard Disk Bay
Cover Removal
4
5
6
7
8
9
Page 97
Upgrading The Computer
Upgrading the Optical (CD/DVD) Device 6 - 7
6
Upgrading the Optical (CD/DVD) Device
1. Turn off the computer, and turn it over and remove the battery.
2. Locate the module bay cover and remove screws
- .
3. Remove the bay cover
.
4. Use a screwdriver to carefully push out the op tical device at point .
5. Reverse the process to install the new device.
Figure 6 - 6
Removing the CD/
DVD Device
1 5
6
7
1
2
3
4
5
7
7
6
Page 98
Upgrading The Computer
6 - 8 Upgrading the System Memory (RAM)
6
Upgrading the System Memory (RAM)
The computer has two memory sockets for 200 pin Small Outline Dual In-line (SO­DIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 1 for details of supported module types).
The total memory size is automatically detected by the POST routine once you turn on your computer.
1. Turn off the computer, and turn it over and remove the batt er y.
2. Locate the module bay cover and remove screws
- .
3. Remove the bay cover .
1 5
6
1
2
3
4
5
6
Figure 6 - 7
Module Bay Cover
Removal
Page 99
Upgrading The Computer
Upgrading the System Memory (RAM) 6 - 9
6
4. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( &
) in Figure 6 - 8.
5. The RAM module will pop-up, and you can remove it.
6. Pull the latches to release the second module if necessary.
7. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot.
8. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure.
9. Press the module in and down towards th e mainboard until the slot levers click into place to secure the module.
10. Replace the module bay cover and screws.
11. Restart the computer to allow the BIOS to register the new memory configuration as it starts up.
7 8
7
8
9
Contact Warning
Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance.
Figure 6 - 8
RAM Module
Removal
9
Page 100
Upgrading The Computer
6 - 10 Upgrading the Processor
6
Upgrading the Processor
If you want to upgrade your computer by replacing the existing processor with a fast­er/new one you will need to contact your customer service representative. We rec­ommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
Warranty
The CPU is not a user serviceable part. Open­ing this compartment, or accessing the CPU in any way, may violate your warranty.
Unauthorized tampering with the HDD may also violate your warranty.
Loading...