Optex Pro Swing PREMIER T Specification Manual

Specification manual

DETECTION AREA

5924401 APR 2016

The actual detection area may become smaller depending on the ambient light, the color / material of the
object or the floor as well as the entry speed of the object.

NOTE

: 1st row area

: 2nd row area

: 3rd row area

Chart shows figures if all angles are set at 0degree.

WARNING

CAUTION

NOTE

Disregard of warning may cause improper operation causing death or serious injury of
a person.

Special attention is required to the section of this symbol.

Disregard of caution may cause improper operation causing injury of a person or damage to
objects.

NOTE

The following conditions may not be suitable for sensor installation.

- Fog or exhaust emission around the door.

- Moving objects or objects that emit light near the detection area.

- Highly reflecting floor or highly reflecting objects around the door.

- Wet floor.

NOTE

WARNING

Do not wash, disassemble, rebuild or repair the sensor, otherwise
it may cause electric shock or breakdown of the equipment.

Danger of electric shock

Read this manual carefully before use to ensure proper operation of this product.
Failure to read this manual may cause improper operation and may result in serious injury or death of a person.
The meanings of the symbols are as follows. Please study the following first and then read the contents of this manual.

1. PREMIER T version Sensor Heads (OA-613 T) & Controller (OC-913C T) are not compatible with
old PREMIER version Sensor Heads (OA-603, OA-613) and controller (OC-903C, OC-913C).
Do not intermix Old & New versions.

2. This sensor is a non-contact switch intended header mount or wall mount for use on automatic swing doors.
Do not use for any other application.

3. When setting the sensor's detection area, make sure that there is no traffic around the installation site.

4. Before turning the power ON, check the wiring to prevent damage or malfunction of equipment connected to
the sensor.

5. Only use the sensor as specified in the operation manual provided.

6. Be sure to install and adjust the sensor in accordance with the local laws and standards of the country in
which the sensor is installed.

7. Before leaving the installation site, make sure that the sensor is operating properly and instruct the building
owner/operator on proper operation of the door and the sensor.

8. The sensor settings can only be changed by an installer or service engineer. When changed, the
changed settings and the date shall be registered in the maintenance logbook accompanying the door.

MANUFACTURER'S STATEMENT

SPECIFICATION

Model (System name)
Power supply

Power consumption

Output *
Test input

Output hold time

Response time
Operating temperature

Operating humidity
Accessories

: PREMIER T
: 12 to 24VAC ±10% (50 / 60Hz)
12 to 30VDC
: < 2.2W (< 4VA at AC)
at 1 OA-613 T & 1 OC-913C T
: CMOS. Relay voltage / 5VDC
: Opto coupler
Voltage 5 to 30VDC
Current 6mA Max. (30VDC)
: 0.5sec. fixed (Activate output)

0.5sec. to 10sec.(Safety output)
: < 0.3sec.
: -4 to 131°F (-20 to +55°C)
without dew condensation
: < 80%
: 1 Spec manual
1 Installation manual
2 Mounting screws
1 Mounting templates for OA-613 T
1 Communication cable 3'3" (1m)
1 Wiring cable 2' (0.6m)
1 Velcro tape
2 Wiring shells

Model (Sensor head)
Cover color
Mounting height
Detection area
Detection method
Depth angle adjustment

IP rate
Weight

Model (Controller)
Weight

: OA-613 T
: Black
: 6'7" (2.0m) to 8'2" (2.5m)
: See DETECTION AREA
: Active infrared reflection **
: 1st row area ±5°
2nd & 3rd row area ±5°
: IP44
: 8.1oz (230g)

: OC-913C T
: 2.3oz (65g)

NOTE

Stand-by

Signal saturation

Sensor failure

1st row area detection

Status

SPECIFICATIONS

2nd or 3rd row area detection

Waiting for next learning

During opening or closing

During learning

Setting error

Communication error

Mixed version error

Solid Green

Slow Green blinking
Fast Green blinking

Blinking Red

Color

Solid Red

Solid Yellow

Solid Orange

Blinking Yellow

Slow Orange blinking

Twice Orange blinking

Red & Green blinking

Door fully closed

During learning

Status

Door fully opened

Door closing

Communication error

Mixed version error

Solid Green

Slow Green blinking

Solid Red

Solid Orange

Twice Orange blinking

Red & Green blinking

Door opening Blinking Red

Color

LED

indication Operation

Safety output

Activate output

Solid Green

OFF

Solid Orange

Activate input

Solid Orange

When not outputting

When outputting
When outputting

When receiving input

OFF

OFF

When not receiving input

When not outputting

Motor input

Solid Green When not receiving Motor positive

Solid Red When not receiving Motor negative

OFF When not receiving input

: Two type of outputs (Activate , Safety)
: All rows have the presence detection.

*
**

The specifications herein are subject to change without prior notice due to improvements.

Operation indicator : OA-613 T

Operation indicator : OC-913C T

Interface LED : OC-913C T

[ft,inch (mm)]

B

C

D

E

F

G

H

I

J

1'2"(364)

7"(182)

1'(23)

2'2"(664)

4'7"(1391)

2'3"(682)

4'4"(1318)

6'9"(2045)

9'5"(2864)

1'4"(400)

8"(200)

1'(25)

2'5"(730)

5'1"(1530)

2'6"(750)

4'9"(1450)

7'5"(2250)

10'4"(3150)

8'2"(2500)

1'6"(455)

9"(227)

1'(28)

2'9"(830)

5'9"(1739)

2'10"(852)

5'5"(1648)

8'5"(2557)

11'9"(3580)

A

6'7"(2000) 7'3"(2200)

OUTER DIMENSIONS AND PART NAMES

[inch (mm)]

2 1/4"(56.5)

9 3/4"(248)

(1)

(2)

(3) (4)

(5) (6) (7)(8)(9)

(10)

(10)

(1)

10 13/16"(275)

Sensor head: OA-613 T

Controller: OC-913C T

(1) : Safety output hold timer
(2) : Knowing Act timer
(3) : Lockout timer
(4) : Dipswitches
(5) : Operation indicator
(6) : Connector
(7) : Interface LED
(

Motor input, Activate input, Safety output,

Activate output)

1 1/8"(29.3)

[inch (mm)]

Activate input

Safety output

Activate output

Safety output
hold time
(0.5 to 10sec.)

Lockout timer
(0 to 24sec.)

MaxMinMaxMin

Directional plug

Operation
indicator

1 432

7

Made in Japan

MaxMin

Knowing Act timer(0 to 24sec.)

5

8

OC-913C T

Motor input

6

Power supply

Power consumption

: 12 to 24VAC ±10%
12 to 30VDC
: < 2.2W(< 4VA at AC)
at 1 OA-613 T & 1 OC-913C T

Safety relay
contact

N.O.

N.C.

1

Door
open signal

Act Saf

2

Auto Lockout

AutoManual

3

Knowing Act

OFF ON

4

Data input

OFF ON

5

PWM

OFF ON

6

Test input

EnableDisable

7

HighLow

Test input

8

(4)

(6)

(7)

(5)

3 1/4" (85)

(1)

(3)

(2)

2 9/16"(65)

: Connector
: Sensitivity potentiometer
: Mode setting switches
: Area width setting switch
: 1st row angle screw
: 1st row area angle gauge
: 2nd & 3rd area angle screw
: 2nd & 3rd area angle gauge
: Operation indicator
: Mounting holes

1 1/4"

(32)

(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)

(10)

1 2

3 4

5

6

789

2' (0.6)

1011

12

16

15

Wiring cable

[inch (mm)]

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16

: Power
: Power
: Motor voltage input positive (+)
: Motor voltage input negative (-)
: Activate input (+)
: Activate input (-)
: Safety(Stall) output
: Safety(Stall) output
: Activate output
: Activate output
: Test input (+)
: Test input (-)
: N/A
: N/A
: Data input (+)
: Data input (-)

: Orange
: Brown
: Red
: Black
: White /Purple line
: Purple
: Blue
: Blue
: Yellow
: Yellow
: Grey / Pink
: Red / Blue

: White / Red line
: White

CAUTION

When using Test input (dipswitch 7) is Enable, Signal lines of
Safety input should not be connected to the same port.

SHALLOWDEEP

AREA DEPTH

6 6

Min Max

1st row area

sensitivity

potentiometer

LOCKOUT TIMER(Sec.)

0 1 2 4

7 8 7 8 7 8 7 8
SNOWNORMAL
55

RAINNORMAL
44

120

1 2

1st row area
sensitivity potentiometer

2nd & 3rd row area
sensitivity potentiometer

1

Area depth angle adjustment

5

Mode setting switch
(Left bank)

4

Area width setting switch
(Right bank)

5-1. Setting the Presence timer

2

ADJUSTMENTS for OA-613 T

Adjusting the Sensitivity

1 2 1 2 1 2 1 2

15 Sec.

30 Sec.

60 Sec. 120 Sec.

33

Setting2Setting1

1st row area
angle screw

2nd &3rd row area
angle screw

Set the dipswitch as necessary.
Active
Inactive

1,2

3
4
5
6

7,8

: Presence timer
: Frequency
: Rain mode
: Snow mode
: Area depth
: Extend Lockout timer

1

Timer adjustment

ADJUSTMENTS for OC-913C T

3

Initial setup

NOTE

InactiveActive

5-2. Setting the Frequency

44

RainNormal

5-3. Setting the Rain mode

55

SnowNormal

5-4. Setting the Snow mode

66

SHALLOWDEEP

5-5. Setting the Area depth 5-6. Setting the Extend Lockout timer

NOTE

Safety output

hold time

(0.5 to 10sec.)

Lockout

timer

(0 to 24sec.)

MaxMinMaxMin

1. Always keep the detection window clean. If dirty, wipe the window with a damp cloth.(Do not use any cleaner / solvent.)

2. Do not wash the sensor with water.

3. Do not disassemble, rebuild or repair the sensor yourself, otherwise electric shock may occur.

4. When the operation indicator blinks Green, contact your installer or service engineer.

5. Always contact your installer or service engineer when changing the settings.

6. Do not paint the detection window.

WARNING

1. After applying power, wait 10 seconds then walk test detection area to ensure proper operation.

2. Do not place any objects that move or emit light in the detection area. (e.g. Plant, illumination, etc.)

NOTE

INFORM BUILDING OWNER / OPERATOR OF THE FOLLOWING ITEMS

NOTE

When set to "Rain", the actual
detection area may become
smaller.

NOTE

7 8 7 8 7 8 7 8

+0 Sec.

+1Sec.

+2 Sec. -1 Sec.

MaxMin

Knowing Act

timer

(0 to 24sec.)

Knowing Act Function

Set the Lockout time to the time for the
door to reach full closed position from
full open position. Lockout timer is
effective only when dipswitch 3 is set to
"Manual" and dipswitch 5 is set to "OFF".

Set the time required for door to close from fully open position to
within 10 degrees when uses for Knowing Act application(dipswitch 4:ON).

See ADJUSTMENTS for OC-913C T

NOTE

Set the Safety output duration time.

OA-613 T

OPERATION INDICATOR

Min Max

Min Max

1st row area

sensitivity

potentiometer

2nd & 3rd row
area sensitivity

potentiometer

Start with 2nd & 3rd row area depth angle
at +5 degrees(deep).
If after walk test the pattern is too deep,
adjust towards shallow as necessary.

For standard
application.

For bi-fold or
smaller door.

: Enable area
: Disable area

Use this function when Primary Activation is Knowing Act (i.e. Push Plate, Card reader, etc.) and
a secondary activation sensor(door mount or header mount) is desired.
See WIRING in the installation manual when Knowing Act Function is required.

Secondary activation sensor status in Knowing Act Function:

- Full Closed position
Secondary activation sensor is inactive until the Knowing Act device is initiated.
Door can be used manually without activation or reactivation from sensor.

- Door opening & Full open
When door is activated by Knowing Act, the secondary activation sensor is active
and the door will remain open when the sensor is in detection.

- Door closing
Secondary activation sensor is active and will reactivate the door upon detection
until the Knowing Act timer expires. Set the Knowing Act timer on OC-913C T control
to stay active to within 10 degrees from full closed.

When using the Knowing Act Function, Push/Pull activation MUST be disabled at the door controller.

Start with 1st row area depth angle
at -5 degrees(shallow).
If after walk test the pattern is too shallow,
adjust towards deep as necessary.

2

Setting the dipswitches

Set the dipswitches as shown below.

Safety relay contact

Door open signal switch

Auto Lockout

Knowing Act

ON

Manual

OFF

Auto

1

2

3

4

5

6

7

8

Dipswitch setting ONOFF

Data input

Test input

Test input High

OFF

Low

ON

Act

NO NC

Saf

PWM

OFF ON

See PREMIER T installation manual step 6
(PREMIER Learn process).

Enable Disable

OPTEX Co.,LTD.

Manufacturer

5-8-12 Ogoto Otsu 520-0101, Japan
TEL.: [phone]
FAX.: [phone]
WEBSITE:
www.optex.co.jp/as/eng/index.html

East coast office

8510 McAlpines Park Drive, Suite 108
Charlotte, NC 28211 U.S.A.
TEL.: [phone]
FAX.: [phone]
WEBSITE: www.optextechnologies.com

OPTEX INCORPORATED

North and South America Subsidiary

18730 S. Wilmington Avenue, Suite 100
Rancho Dominguez CA 90220 U.S.A
TEL.: [phone]
FAX.: [phone]
WEBSITE: www.optextechnologies.com

1. Safety relay contact
: Choose the Relay contact.

2. Door open signal switch
: Determines safety output when door is open.

3. Auto Lockout
: Set the Lockout method
ON : Manual (by volume setting on OC-913C T)
OFF : Auto (by motor voltage)

4. Knowing Act
: If uses Knowing Act Function, set to "ON".

5. Data input
: If using data output from door control for Lockout, set to "ON".
When Data input is "ON", setting of Auto Lockout(dipswitch 3) is ignored.

6. PWM
: If using PWM from door control for Lockout, set to "ON”.
When using PWM, dipswtich 5 also needs to be set to "ON" and setting of Auto Lockout(dipswitch 3) is ignored.

7. Test input
: If not using Test input from door control for Lockout, set to "ON". When not using Test input, dipswitch 7 also needs
to be set to "ON", and setting of Test input(dipswitch 8) is ignored.

8. Test input
: If using Test input of "Active Low" for Lockout, set to "ON".

Whenever a dipswitch is moved a PREMIER Learn process is enabled, ensure proper completion of process
(See step 3).

This sensor has the function to fit floor condition
changes automatically.
Therefore, even if objects are put in the detection
area, sensor will learn the changes gradually and
set back to normal operations automatically after
presence timer has expired.
To enable a Learn process only, flip any dipswitch
on OA-613 T sensor head and wait 1 second,
then flip it back to the original position.

Check the wiring cable.

Check the connector.

Replace as necessary.

Check the dipswitch settings.

Verify proper settings.
See installation manual step 5.

Possible countermeasures

Set to the stated voltage.

Wrong wiring cable (Brown &Orangewires)
of OC-913C T.

Connection failure from OA-613 T to
OC-913C T.

Twice
Orange
blinking

Defective communication cable.

Blinking

Yellow

Blinking

Green

OC-913C T dipswitches set wrong.

Solid

Green

or

Solid

Red

or

Blinking

Red

Proper

Set dipswitch 6 on left bank dipswitch of
OA-613 T on/up (shallow).

Remove the objects.

Verify proper settings.
See installation manual step 5.

Adjust the sensitivity lower.

Set the snow mode to "Snow".

Set the rain mode to "Rain".

Use the rain-cover
(Separately available). Or install in a
place keeping the water drops off.

Check the installation condition referring
to MANUFACTURER'S STATEMENT.

Remove the objects.

Stalling caused by traffic just outside of
swing path.

Moving objects near guide rails.

Area width dipswitches set wrong.
(Right bank dipswitches on OA-613 T)

Sensitivity is too high.

Snow drifting.

Other than above.

Water drops on the detection window.

Wet floor.
The exhaust emission or fog penetrate
into the detection area.

Reflecting objects in the detection area.

Objects that move or emit light
(Ex.Plant, illumination, etc.)

Red or

Blinking

Red

Verify proper settings.
See installation manual step 5.

Area width dipswitches set wrong.
(Right bank dipswitches on OA-613 T)

Slow
Orange
blinking

When all the area are inactive.
(Right bank dipswitches on OA-613 T)

Twice
Orange
blinking

or

None

Proper

Symptom

OA-613 T

None

Operation indicator

OC-913C T

Adjust the sensitivity higher.Sensitivity is too low.

Solid

Green

Proper

Possible cause

Power supply voltage.None

Slow

Green
blinking

Proper

Signal saturation.

Sensor failure.

Fast

Green
blinking

Proper

Remove highly reflecting objects from
the detection area. Or lower the
sensitivity.

Set 1st row area angle at -5 degrees
(shallow) or 2nd & 3rd row area angle
at +5 degrees (deep).

Improper 1st row or 2nd & 3rd row area
angle adjustment.

Wipe the detection window with a damp
cloth.

(Do not use any cleaner or solvent.)

Dirty detection window.

Contact your installer or service
engineer.

TROUBLESHOOTING

OC-913C T dipswitches set wrong. Check the dipswitch settings.

See installation manual step 2.

Initial setup
can not start.

Incomplete
initial setup

Sensor detects
when no one
is in the
detection area.
(Ghosting)

Set 1st row area angle at -5 degrees
(shallow) or 2nd & 3rd row area angle
at +5 degrees (deep).

Improper 1st row or 2nd & 3rd row area
angle adjustment.

Door does not
operate properly
when a person
enters the
detection area.
(Sensor does
not detect.)

OA-613 T
detects but door
operate.

Solid

Green

Proper

Improper wiring of door equipment on /
off / hold switch.

Verify proper wiring of on / off /
hold switch.

Door remains
open.

When using more than one sensor close to each
other, set the different frequency for each sensor by
dipswitch 3.

To comply with ANSI standard, set to "30sec." or
longer.

Set dipswitch 4 to "Rain" if the sensor is used in a
region with a lot of rain.

Set dipswitch 5 to "Snow" if the sensor is used in
a region with snow or a lot of insects.

Fine-tune the Lockout time after setting the Lockout
timer on OC-913C T by volume (0-24 sec.)
Only effective when dipswitch 3 is set to "Manual"
and dipswitch 5 is set to "OFF" on OC-913C T.