Optex Pro-Swing Premier Mk2 Specification Manual

85(3 1/4")

65(2 9/16")

(1)

(3)

(4)

(6)

(7)

(5)

248(9 3/4")

(1)

(2)

(3) (4)

(5) (6) (7)(8)(9)

(10)

(10)

(1)

29.3(1 1/8")

[mm (inch)]

PREMIER Mk2

Specification manual

DETECTION AREA

5918770 OCT 2011

WARNING

CAUTION

NOTE

Disregard of warning may cause improper operation causing death or serious injury of
a person.

Special attention is required to the section of this symbol.

Disregard of caution may cause improper operation causing injury of a person or damage to
objects.

NOTE

The following conditions may not be suitable for sensor installation.

-Fog or exhaust emission around the door.

-Wet floor.

-Moving objects or objects that emit light near the detection area.

-Highly reflecting floor or highly reflecting objects around the door.

NOTE

WARNING

Do not wash, disassemble, rebuild or repair the sensor, otherwise
it may cause electric shock or breakdown of the equipment.

Danger of electric shock

Read this manual carefully before use to ensure proper operation of this product.
Failure to read this manual may cause improper operation and may result in serious injury or death of a
person. The meanings of the symbols are as follows. Please study the following first and then read the contents of
this manual.

1. Premier MK2 version Sensor Heads (OA-613) & Controller (OC-913C) are not compatible with
old Premier version Sensor Heads (OA-603) and controller (OC-903C).
Do not intermix Old & New versions.

2. This sensor is a non-contact switch intended

header mount or wall mount for use on automatic swing doors.

Do not use for any other application.

3. When setting the sensor's detection area, make sure that there is no traffic around the installation site.

4. Before turning the power ON, check the wiring to prevent damage or malfunction of equipment connected to
the sensor.

5. Only use the sensor as specified in the operation manual provided.

6. Be sure to install and adjust the sensor in accordance with the local laws and standards of the country in which
the sensor is installed.

7. Before leaving the installation site, make sure that the sensor is operating properly and instruct the building
owner/operator on proper operation of the door and the sensor.

8. The sensor settings can only be changed by an installer or service engineer. When changed, the
changed settings and the date shall be registered in the maintenance logbook accompanying the door.

MANUFACTURER'S STATEMENT

MANUFACTURER'S STATEMENT

SPECIFICATION

Model (System name)
Power supply

Power consumption

Output *
Output hold time

Response time
Operating temperature

Operating humidity
Accessories

: PREMIER Mk2
: 12 to 24 VAC ±10% (50 / 60 Hz)
12 to 30 VDC
: < 2.2W (< 4VA at AC)
at 1 OA-613 & 1 OC-913C
: CMOS. Relay Voltage / 5 VDC
: 0.5 sec. fixed (Activate output)

0.5 sec. to 10sec.(Safety output)
: < 0.3 sec.
: -20 to +55°C (-4 to 131°F)
without dew condensation
: < 80%
: 1 Spec manual
1 Installation manual
2 Mounting screws
1 Mounting templates for OA-613
1 Communication cable 1m (3'3")
1 Wiring cable 0.6m (2')
1 Velcro tape
2 Wiring shells
1 Connection Matrix

Model (Sensor head)
Cover color
Mounting height
Detection area
Detection method
Depth angle adjustment

IP rate
Weight

Model (Controller)
Weight

: OA-613
: Black
: 2.0 (6'7") to 2.5m (8'2")
: See DETECTION AREA
: Active infrared reflection **
: 1st row area ±5°
2nd & 3rd row area ±5°
: IP44
: 230g (8.1oz )

: OC-913C
: 65g (2.3oz )

The specifications herein are subject to change without prior notice due to improvements.

NOTE

: Three type of outputs (Activate , Inhibit , Safety)
: All rows have the presence detection.

Operation indicator : OA-613

Stand-by

Signal saturation

Sensor failure

1st row area detection

Status

SPECIFICATIONS

*
**

2nd or 3rd row area detection

Waiting for next learning

During opening or closing

During learning

Setting error

Communication error

Mixed version error

Solid Green

Slow Green blinking
Fast Green blinking

Blinking Red

Color

Solid Red

Solid Yellow

Solid Orange

Blinking Yellow

Slow Orange blinking

Twice Orange blinking

Red & Green blinking

Operation indicator : OC-913C

Door fully closed

During Learning

Status

Door fully opened

Door closing

Communication error

Mixed version error

Solid Green

Slow Green blinking

Solid Red

Solid Orange

Twice Orange blinking

Red & Green blinking

Door Opening Blinking Red

Color

Interface LED : OC-913C

Inhibit output

LED

indication

Safety output

Activate output

Solid Green

OFF

Solid Green

OFF

Solid Orange

Operation

Activate input / Beam input

Solid Orange

When outputting
When not outputting
When not outputting

When outputting

When outputting

When receiving input

OUTER DIMENSIONS AND PART NAMES

[mm (inch)]

56.5(2 1/4")

32(1 1/4")

275(10 13/16")

Sensor head: OA-613

Controller: OC-913C

: Connector
: Sensitivity potentiometer
: Mode setting switches
: Area width setting switch
: 1st row angle screw
: 1st row area angle gauge
: 2nd & 3rd area angle screw
: 2nd & 3rd area angle gauge
: Operation indicator
: Mounting holes

1
2
3
4
5
6
7
8
9

10

1 : Safety output hold timer
2 : Knowing Act timer
3 : Lockout timer
4 : Dipswitches
5 : Operation indicator
6 : Connector
7 : Interface LED
(

Inhibit output, Safety output, Activate output,

Activate/Beam input)

The actual detection area may become smaller depending on the ambient light, the color / material of
the object or the floor as well as the entry speed of the object.

NOTE

[mm (ft,inch)]

: 1st row area

: 2nd row area

: 3rd row area

Chart shows figures if all angles are set at 0degree.

5733580

Green

Red Blink

Red

Yellow Blink

: Stand-by

:

1st Row Area

Det.

: 2

nd󲷅5tf Row Area

Det.

: Learning

OPERATION INDICATOR

SHALLOWDEEP

AREA DEPTH

6 6

CONNECTOR

1st row area depth Adjustment

DEEP

SHALLOW

SHALLOW

DEEP

SHALLOW
PATTERN

DEEP

PATTERN

OPERATION INDICATOR

Min Max

Min Max

Active Inactive

AREA WIDTH SWITCH

2nd 󲷅5tf row area depth Adjustment

DEEP

SHALLOW

DEEP
PATTERN

SHALLOW
PATTERN

DEEP

SHALLOW

CONNECTOR

Each number of Area

can be eliminated

by using each dip-SW.

1st row area

sensitivity

potentiometer

2nd󲷅5tf row
area sensitivity
potentiometer

EXTEND
LOCKOUT TIMER(Sec.)

+0 +2 -1

78 78 78 78

SNOW MODE

UPQYPQTOCN

55

RAIN MODE

TCKPPQTOCN

44

FREQUENCY
SWITCH

"UGVVKPI3

3

UGVVKPI4

3

PRESENCE
TIMER(Sec.)

37

1252128212

342

12

+1

OA-613

(2)

OFF

OFF

When not receiving input

When not outputting

Activate

/Beam input

Safety

output

Activate

output

Inhibit

output

Safety output

hold time

(0.5 to 10sec.)

Lockout timer

(0 to 24sec.)

MaxMinMaxMin

Safety

Relay Contact

N.O.

N.C.

1

Door

Open Signal

Act Saf

2

Auto Lock Out

AutoManual

3

Knowing Act

OFF ON

4

Data Input

Directional Plug

Operation
Indicator

1

432

7

6

Ocfg"kp"Lcrcp

NQV0zzzz{¦¦¦¦

MaxMin

Knowing Act timer(0 to 24sec.)

5

OFF ON

6 7

Future

Development

Stand Alone

8

OFF ON

5 8

Power supply : 12 to 24 VAC ±10%

12 to 30 VDC
Power consumption : <2.2W(<4VA at AC)
at 1 OA-613 & 1 OC-913C

OC-913C

SHALLOWDEEP

AREA DEPTH

6 6

Min Max

1st row area

sensitivity

potentiometer

LOCKOUT TIMER(Sec.)

0 1 2 4

7 8 7 8 7 8 78

612:1250$/

5

5$,11250$/

4



1 2

1st row area
sensitivity potentiometer

2nd & 3rd row area
sensitivity potentiometer

Check the wiring cable.

Check the connector.

Replace as necessary.

Check the

dipswitch settings

.

Set 1st row area angle at -5 degrees
(shallow) or 2nd & 3rd row area angle
at +5 degrees (deep).

Set dipswitch 6 on left bank dipswitch of
OA-613 on/up (shallow).

Remove the objects.

Verify proper settings.
See installation manual section 4.

Adjust the sensitivity lower.

Adjust the sensitivity higher.

Set the snow mode to “Snow”.

Set the rain mode to “Rain”.

Use the rain-cover (Separately available).
Or install in a place keeping the
water drops off.

Check the installation condition referring
to MANUFACTURER'S STATEMENT.

Remove the objects.

Verify proper settings.
See installation manual section 4.

Verify proper settings.
See installation manual section 4.

Possible countermeasures

Set to the stated voltage.

Wrong wiring cable (Brown &Orange wires)
of OC-913C.

Connection failure from OA-613 to
OC-913C.

Twice
Orange
blinking

Defective communication cable.

Blinking

Yellow

Blinking

Green

OC-913C dipswitches set wrong.

Solid

Green

or

Solid

Red

or

Blinking

Red

Proper

Improper 1st row or 2nd & 3rd row area
angle adjustment.

Stalling caused by traffic just outside of
swing path.

Moving objects near guide rails.

Area width dipswitches set wrong.
(Right bank dipswitches on OA-613)

Sensitivity is too high.

Sensitivity is too low.

Snow drifting.

Other than above.

Water drops on the detection window.

Wet floor.
The exhaust emission or fog penetrate
into the detection area.

Reflecting objects in the detection area.

Objects that move or emit light
(Ex.Plant, illumination, etc.)

Red or

Blinking

Red

Area width dipswitches set wrong.
(Right bank dipswitches on OA-613)

Slow

Green

blinking

Proper

Signal saturation

.

Sensor failure.

Fast

Green

blinking

Proper

Slow
Orange
blinking

When all the area are inactive.
(Right bank dipswitches on OA-613)

Solid
Green

Proper

Twice
Orange
blinking

or

None

Proper

Solid

Green

Proper

Symptom

OA-613

None

Operation indicator

OC-913C

Initial setup
can not start.

Incomplete
initial setup

Door operates
when no one
is in the
detection area.
(Ghosting)

OA-613 detects
but door operate.

Door remains
open.

Door does not
operate properly
when a person
enters the
detection area.
(Sensor does
not detect.)

Possible cause

Power supply voltage.None

OC-913C dipswitches set wrong.

Check the

dipswitch settings

.

See installation manual section 2.

Remove highly reflecting objects from the
detection area. Or lower the sensitivity.

Set 1st row area angle at -5 degrees
(shallow) or 2nd & 3rd row area angle
at +5 degrees (deep).

Improper 1st row or 2nd & 3rd row area
angle adjustment.

Wipe the detection window with a damp
cloth. (Do not use any cleaner or solvent.)

Dirty detection window.

Contact your installer or service engineer.

Improper wiring of door equipment on / off /
hold switch.

Verify proper wiring of on / off /
hold switch.

2

Setting the dipswitches

1

Area depth angle adjustment

5

Mode setting switch
(left bank)

4

Area width setting switch
(right bank)

5-1.Setting the presence timer

2

ADJUSTMENTS for OA-613

Adjusting the sensitivity

1. Always keep the detection window clean. If dirty, wipe the window with a damp cloth.(Do not use any cleaner / solvent.)

2. Do not wash the sensor with water.

3. Do not disassemble, rebuild or repair the sensor yourself, otherwise electric shock may occur.

4. When the operation indicator blinks Green, contact your installer or service engineer.

5. Always contact your installer or service engineer when changing the settings.

6. Do not paint the detection window.

WARNING

1. After applying power, wait 10 seconds then walk test detection area to ensure proper operation.

2. Do not place any objects that move or emit light in the detection area. (e.g. Plant, illumination, etc.)

NOTE

INFORM BUILDING OWNER / OPERATOR OF THE FOLLOWING ITEMS

1 2 1 2 1 2 1 2

15 Sec.

30 Sec.

60 Sec. 120 Sec.

33

Setting2Setting1

To comply with ANSI standard, set to "30sec." or longer.

1st row area
angle screw

2nd &3rd row area
angle screw

Set the dipswitch as necessary.
Active
Inactive

1,2

3
4
5
6

7,8

: Presence timer
: Frequency
: Rain mode
: Snow mode
: Area depth
: Extend Lockout timer

1

Timer adjustment

ADJUSTMENTS for OC-913C

3

Initial setup

This sensor has the function to fit floor condition changes
automatically.
Therefore, even if objects are put in the detection area,
sensor will learn the changes gradually and set back to
normal operations automatically after presence timer has
expired.
To enable a Learn process only, flip any dipswitch
on OA-613 sensor head and wait 1 second, then flip it
back to the original position.

NOTE

See PREMIER Mk2 installation manual section 6
(Premier Learn process).

InactiveActive

5-2.Setting the frequency

When using more than two sensors close to each other,
set the different frequency for each sensor by dipswitch 3.

44

RainNormal

5-3.Setting the rain mode

Set dipswitch 4 to "Rain" if the sensor is used in a
region with a lot of rain.

55

SnowNormal

5-4.Setting the snow mode

Set dipswitch 5 to "Snow" if the sensor is used in a
region with snow or a lot of insects.

66

SHALLOWDEEP

5-5.Setting the area depth 5-6.Setting the Extend Lockout timer

NOTE

Safety output

hold time

(0.5 to 10sec.)

Lockout

timer

(0 to 24sec.)

MaxMinMaxMin

Set the dipswitches as shown below.

OPTEX Co.,LTD.

Manufacturer

5-8-12 Ogoto Otsu 520-0101, Japan
TEL.: [phone]
FAX.: [phone]
WEBSITE: www.optex.co.jp

East Coast Office

8510 McAlpines Park Drive, Suite 108
Charlotte, NC 28211 U.S.A.
TOLL-FREE: 800 877 6656
FAX.: [phone]
WEBSITE: www.optextechnologies.com

OPTEX Technologies Inc.

Corporate Headquarters

North and South American Subsidiary

3882 Del Amo Blvd., Suite 604
Torrance, CA 90503 U.S.A.
TOLL-FREE: 800 877 6656
FAX.: [phone]
WEBSITE: www.optextechnologies.com

TROUBLESHOOTING

NOTE

When set to "Rain", the actual
detection area may become
smaller.

NOTE

Whenever a Dipswitch is moved a Premier Learn process is enabled, ensure proper completion of
process (See step 3).

7 8 7 8 7 8 7 8

+0 Sec.

+1Sec.

+2 Sec. -1 Sec.

Fine-tune the lockout time after setting the lockout timer
on OC-913C by volume (0-24 sec.)
Only effective when Dipswitch 3 is set to “Manual” and
Dipswitch 5 is set to “OFF” on OC-913C.

MaxMin

Knowing act

timer

(0 to 24sec.)

Knowing Act Function

1. Safety Relay Contact

2. Door Open Signal Switch

3. Auto Lock out

4. Knowing Act

5. Data Input

6,7. Future Development (not used)

8. Stand Alone

Set the lockout time to the time for the door
to reach full closed position
from full open position. Lockout timer is
effective only when dipswitch 3 is set
to “Manual” and dipswitch 5 is set to “OFF”.

Set the time required for door to close from fully open position to
within 10 degrees when uses for Knowing Act application(dipswitch 4:ON).

See ADJUSTMENTS for OC-913C

NOTE

Set the safety output duration time.

5733580

OA-613

Green

Red Blink

Red

Yellow Blink

: Stand-by

:

1st Row Area

Det.

: 2

nd㸤UG Row Area

Det.

: Learning

OPERATION INDICATOR

SHALLOWDEEP

AREA DEPTH

6 6

CONNECTOR

1st row area depth Adjustment

DEEP

SHALLOW

SHALLOW

DEEP

SHALLOW
PATTERN

DEEP

PATTERN

OPERATION INDICATOR

Min Max

Min Max

Active

Inactive

AREA WIDTH SWITCH

2nd 㸤UG row area depth Adjustment

DEEP

SHALLOW

DEEP
PATTERN

SHALLOW
PATTERN

DEEP

SHALLOW

CONNECTOR

Each number of Area

can be eliminated

by using each dip-SW.

1st row area
sensitivity
potentiometer

2nd㸤UG row
area sensitivity

potentiometer

EXTEND
LOCKOUT TIMER(Sec.)

+0 +1 +2 -1

78 78 78 78

SNOW MODE

612:1250$/

55

RAIN MODE

5$,11250$/

44

FREQUENCY
SWITCH

6(77,1*

3

6(77,1*

3

PRESENCE
TIMER(Sec.)



121212



12

OA-613

OPERATION INDICATOR

Min Max

Min Max

1st row area

sensitivity

potentiometer

2nd 㸤UG row
area sensitivity

potentiometer

Start with 2nd & 3rd row area depth angle
at +5 degrees(deep).
If after walk test the pattern is too deep,
adjust towards shallow as necessary.

For standard
application.

For bi-fold or
smaller door.

OC-913C Dip-SW 8 is ON,
but OA-613 is also connected to OC-913C.

: Enable area
: Disable area

Use this function when Primary Activation is knowing act (i.e. Push Plate, Card reader, etc.) and
a secondary activation sensor(door mount or header mount) is desired.
See WIRING in the installation manual when Knowing Act Function is required.

Secondary activation sensor status in Knowing Act Function:

- Full Closed position
Secondary activation sensor is inactive until the knowing act device is initiated.
Door can be used manually without activation or reactivation from sensor.

- Door Opening & Full Open
When door is activated by Knowing Act, the secondary activation sensor is active
and the door will remain open when the sensor is in detection.

- Door closing
Secondary activation sensor is active and will reactivate the door upon detection
until the Knowing Act timer expires. Set the Knowing Act timer on OC-913C control
to stay active to within 10 degrees from full closed.

When using the Knowing Act Function, Push/Pull activation MUST be disabled at the door control.

Safety Relay Contact

Door Open Signal Switch

Auto Lock Out

Knowing Act

ON

Manual

OFF

Auto

1

2

3

4

5

6

7

8

Dipswitch setting ONOFF

Data Input

Future Development

Stand Alone

OFF

OFF

ON

ON

Act

NO NC

Saf

: Choose the Relay Contact.

: Determines safety output when door is open.

: Set the lockout method
ON : Manual (by volume setting on OC-913C)
OFF : Auto (by motor voltage)

: If uses KnowingAct Function, set to “ON”.

: If using data output from door control for Lockout, set to “ON”.
When Data Input is “ON”, setting of Auto Lock Out(dipswitch 3) is ignored.

: Set to “ON” when door mount sensor and OC-913C are used
for Knowing Act application without OA-613.

If use OA-613, set OC-913C Dip-SW 8
to “OFF”.
If do not use OA-613, disconnect it.

When using OA-613, dipswitch 8 must be set to “OFF”.

Start with 1st row area depth angle
at -5 degrees(shallow).
If after walk test the pattern is too shallow,
adjust towards deep as necessary.

CAUTION