Optex Prosafe OA-1V, Prosafe OA-2VF, Prosafe OA-205V-1, Prosafe OA-2V, Prosafe OA-205V-2 Operation Manual

Download

Page 1

12345678

245 ( 9 5/8" )

125 ( 4 15/16" )

36 ( 1 7/16" )

68 ( 2 11/16" )

37 ( 1 7/16" )

43 ( 1 11/16" )

01.0m 1.0m 2.0m

3.0m

2.8m

2.6m

2.4m

2.2m

2.0m

1.0m

3.0m

2.8m

2.6m

2.4m

2.2m

2.0m

1.0m

01.0m2.0m 1.0m

3.0m

2.8m

2.6m

2.4m

2.2m

2.0m

1.0m

01.0m 1.0m

MANUFACTURER’S STATEMENT

Read this Operation Manual carefully before use, to ensure proper operation of this Optex sensor. Failure to read this Operation Manual may cause improper sensor operation and may result in serious injury or death. This product is a non-contact activating switch intended for mounting on the header of an automatic door. Do not use it for any other applications; otherwise proper operation and safety cannot be guaranteed. Cautions:

Follow the instructions (especially Note ) in this Operation Manual when installing and

adjusting the sensor.

2. When setting the sensor's area pattern, make sure there is no traffic around the installation site.

3. Before turning the power on, check the wiring to prevent damage or malfunction of equipment that is connected to the sensor.

4. Do not wash, disassemble, rebuild or repair the sensor by yourself; otherwise it may cause electric shock or breakdown of the sensor.

5. Only use the sensor as specified in the supplied instructions.

6. Be sure to install the sensor in accordance with the local laws and standards of your country.

7. Before leaving the jobsite, be sure that this sensor is operating properly and instruct the building owner/operator on proper operation of the door and this sensor.

1 : Mounting Screws 2 : Connector 3 : Sensitivity Switch 4 : Mounting holes 5 : Dipswitches 6 : Area Adjustment Screw 7 : Width Adjustment Shutters 8 : Base Angle Scale 9 : Area Adjustment Tool 10: Operation Indicator 11: Detection Window

mm (inch)

*The specifications herein are subject to change without prior notice due to improvements.

Model Cover color type Mounting Height Detection Area Detection Method Detection Angle Adjustments

Detection Width Adjustments Power Supply Current Draw Power Consumption Operation Indicator

Output Relay Hold Time Response Time Operating Temperature Weight Accessories

OA-1V / OA-2V / OA-2VF / OA-205V-1 / OA-205V-2 : Silver / Black : 2.0m (6’6”) to 3.0m (9’10”) : See “ADJUSTMENT - 1. Detection Area” : Active Infrared Reflection Method : Base Angle: -2° to 10° for OA-1V/OA-205V-1 0° to 10° for OA-2V/2VF/OA-205V-2 Adjustment Screw Angle: ±4° adjustable by 1°

every one click (Deep / Shallow)

: Adjustment Screw Angle: ±7° adjustable by 3.5°

every one click (Right / Left) : 12 to 110V AC / DC (50/60Hz) : 160mA Max. (at 12V AC) : 4.0VA Max. (at 100V AC) : Green / Stand-by Red / 1st Row Detection Active Orange / 2nd Row Detection Active (OA-1V/OA-205V-1 has no 2nd Row.) : “Form A” relay 50V 0.1A Max. (Resistance Load) : 0.5 sec. : < 0.3 sec. : -20°C to +55°C (-4°F to +131°F) : 230g (8.2oz) : 1 Cable 3m (9’10”), 2 Mounting Screws 1 Operation Manual, 1 Mounting Template 1 Area Adjustment Tool, 1 Protection sheet

INSTALLATION

1. Affix the Mounting Template to the mounting surface.

2. Drill two mounting holes (ø 3.4mm or 1/8”).

3. To carry through the wire to the header, drill a wiring hole (ø 8mm or 5/16”).

4. After drilling the holes, remove the Mounting Template.

Note Be sure that the mounting height is within the value

of those in "SPECIFICATIONS."

Remove the cover and attach the sensor with screws.

Plug the Connector for the sensor to that for the cable.

Supply power to the sensor. Adjust the detection area and set the various Switches. (See “ADJUSTMENT.”) Note Make sure that you connect the cable correctly to the

Control Unit of the door before turning the power on.

1.Stick a protection sheet on the sensor.

2. Put back the cover on the sensor.

3. If wiring is to be exposed, break the Knockout.

Yellow Output : “Form A” relay Yellow 50V 0.1A Max. (Resistance Load) Grey Power Supply Grey 12 to 110V AC / DC (50/60Hz)

Note Connect the cable when main power is turned off. Note When passing through the cable to the hole, make sure

not to tear shield: otherwise it may cause electric shock or breakdown of sensor.

Note Do not use the sensor without the cover. Install the sensor indoors , or use the rain-cover (Optional), when using the Knockout, otherwise it may cause electric shock or breakdown of sensor.

The cable is arranged to connect to the door controller properly as shown below.

Adjusting the Pattern Width

Pattern when changed 7 to Left

Pattern when Standard

ADJUSTMENT

: Erasable Area

Setting the Width adjustment shutters

Adjusting the Width Angle Left or Right : between 0 to 7 (3.5 per click)

1278

to Right

A 2.00 2.20 2.50 2.70 3.00

*The values of the chart blow is of the Emitting Spots, but not of

the Detection Area. The actual Detection Area may become smaller depending on the ambiance light and the colour / material of object and the floor as well as the entry speed of object.

[m]

After adjustment, turn the power off and on again, be sure to walktest all of detection areas.

Detection Area

1st Row

2nd Row

OA-1V/OA-205V-1

OA-2V/OA-2VF/OA-205V-2

SPECIFICATIONS OUTER DIMENSIONS

5911961 2005.07

1st Row

to Left

[m]

: Detection Area

: Emitting Spots

: Detection Area

: Emitting Spots

Pattern when changed 7 to Right

Note Setting the pattern for exact door opening may give a slow response to side approaching traffic.

Presence Detection Motion Detection

Provided Detection Row type 1st 2nd

: Erasable Area

Knockout

Mounting Template

2m to 3m

( 6’6" to 9’10")

F 0.27 0.29 0.33 0.36 0.40

B 2.10 2.30 2.60 2.80 3.10 C 0.73 0.80 0.91 0.98 1.09 D 0.85 0.93 1.06 1.14 1.27 E 0.16 0.18 0.20 0.22 0.25

G 1.34 1.47 1.68 1.81 2.01

Eliminate Eliminate Eliminate

Opens All Areas

to Left

to Right

OA-2VF does not have 1st Row Spots during stand-by. Refer to "4-Setting of Dipswitches" in detail.

Area arrangement changes with models. Please adjust after taking into consideration.

OA-1V OA-205V-1 OA-2V OA-205V-2 OA-2VF

Base Angle: 0°, Adjustment Screw Angle: 0°

Base Angle: 10°, Adjustment Screw Angle: 0°

A 2.00 2.20 2.50 2.70 3.00

C 1.25 1.38 1.56 1.69 1.88 D 1.41 1.55 1.76 1.90 2.12 E 0.51 0.56 0.64 0.69 0.77 F 0.65 0.72 0.81 0.88 0.98 G 2.05 2.26 2.56 2.77 3.08

B 2.40 2.64 3.00 3.24 3.60

Page 2

03.0m 2.0m 1.0m

3.0m

2.8m

2.6m

2.4m

2.2m

2.0m

1.0m

03.0m 2.0m 1.0m

3.0m

2.8m

2.6m

2.4m

2.2m

2.0m

1.0m

03.0m 2.0m 1.0m

3.0m

2.8m

2.6m

2.4m

2.2m

2.0m

1.0m

03.0m 2.0m 1.0m

3.0m

2.8m

2.6m

2.4m

2.2m

2.0m

1.0m

03.0m 2.0m 1.0m

3.0m

2.8m

2.6m

2.4m

2.2m

2.0m

1.0m

03.0m 2.0m 1.0m

3.0m

2.8m

2.6m

2.4m

2.2m

2.0m

1.0m

3. Setting the Row with the Dipswitch 8 (for only OA-2V/OA-205V-2).

Pattern when Base Angle 10

Adjusting the Pattern Depth

Setting the Sensitivity

Normally set to “M.” “H” increases the sensitivity and “L” lowers the sensitivity.

Setting the Presence timer

1st Row from door provide the presence detection. (1) Select the presence timer. (2) Turn the power off and on again. Otherwise it may leave

door open for the duration of the presence time set.

(3) After making sure that the door closes, wait for 10

seconds before entering the detection area to set the Presence timer.

Setting the Frequency Function (Interference Prevention)

Four different frequencies can be set by adjusting the Dipswitch 3 and 4.

Note When two or more sensors are installed close to each other, it is possible that they interfere. When that happens, change the Frequency.

Setting the immunity mode

Set the Dipswitch5 if the sensor is used in a region with snow or a lot of insects.

2. Setting the Depth Angle between -4

to 4 (1 per click)

by Adjustment Screw.

Shallow

Depth

Setting the 1st Row detectable timer (For only OA-2VF)

Select the 1st Row detection time by adjusting the Dipswitch 7 and 8.

Note The door may close when this sensor broke down.

Entry motion

Power OFF

Outside the Detection area

OA-1V

OA-205V-1

(image)

Sensor status

Power OFF Stand-by

Motion Detection Active

Entry into 2nd Row Entry into 1st Row

Outside the Detection area

Motion or Presence Detection Active

Stand-by

Orange Red Green

Output

Operation indicator

GreenOFF

Yellow Yellow

CHECKING

Check the operation according to the chart below.

TROUBLESHOOTING

Inform the following items to the building owner/operator

1. When turning the power on, always walk-test the sensor pattern to ensure proper operation.

2. Always keep the detection window clean. If dirty, wipe the window with a damp cloth. (Do not use any cleaner or solvent.)

3. Do not wash the sensor with water.

4. Do not disassemble, rebuild or repair the sensor yourself; otherwise electric shock may occur.

5. Contact your installer or the sales engineer if you want to change the settings.

6. Do not place an object that moves or emits light in the detection area. (Ex. Plant, illumination, etc.)

7. Do not paint the Detection Window.

Contact your installer or the sales engineer if:

- you need to change the settings or replace the sensor.

- the trouble still persists after checking and remedying as described above.

Does not operate

Dose not operate consistently

Operates by itself (Ghosting)

Power supply is not adequate. Connection Failure.

Dirty detection window.

Sensitivity is Low.

There is an object that moves or emits light in the detection area. (Ex. Plant, illumination, etc.) Vibration of the header.

Sensitivity is high.

Waterdrops on detection window.

Detection area has interfered the area of another sensor. The detection 1st row spots are overlapping with the door / header.

Door stay open or closed

There is an reflected object in the detection area. Solar light reflects.

Presence timer is Infinity. There was an abrupt condition change in the detection area.

Adjust to stated voltage. Check the wiring and the connector.

Wipe the detection window with a damp cloth. (Do not use any cleaner or solvent.) Set the Sensitivity Switch “H.”

Set the Sensitivity Switch “L.”

Remove the object.

Secure the header. Or set the Sensitivity Switch “L.”

Install in a place keeping the waterdrops off. OR

use a rain-cover (Optional).

Set the different frequency position each other.

Adjust the detection area to deep (outside).

Turn the power off and on again.

Trouble Possible Cause Solution

There was a puddle left by rain or snow. The floor has gotten wet.

The exhaust of the car and the fog penetrate into the detection area.

This sensor is equipped with the anti-malfunction. However, pay attention when installing as malfunction may occur under the left conditions.

OPTEX CO., LTD.

(ISO 9001 Certified by LRQA) 5-8-12 Ogoto Otsu 520-0101, Japan TEL.: +81 (0)77-579-8700 FAX: +81 (0)77-579-7030 WEBSITE: www.optex.co.jp

Setting of Sensitivity Switch and Dipswitches

Sensitivity Switch Dipswitches

1 2 3 4 5 6 7 8

L M H

Depth angle can be set up by two kinds, a base and an adjustment screw.

1. Setting the Base Angle. OA-1V/OA-205V-1: between -2

to 10 .

OA-2V/2VF/OA-205V-2: between 0 to 10 .

Pattern when Base Angle 5

Pattern when Base Angle -2

-5

:Adjustable Area by Adjustment Screw ±4°

-2 0

2ROW

1ROW

:Adjustable Area by Adjustment Screw ±4°

-7

-5

OA-2V

OA-205V-2

(image)

OA-2VF

(image)

During 1st Row detectable time ,after leaving the Detection area

Green

1st Row detectable Stand-by

Pattern when Base Angle 10

Pattern when Base Angle 5 Pattern when Base Angle 0

OA-1V/OA-205V-1

OA-2V/OA-2VF/OA-205V-2

Yellow Yellow

Normal Immunity

2sec. 15sec. 180sec.

5sec. 10sec. 15sec. 20sec.

Position Position Position Position 1 2 3 4

Note Be aware of non-detection area by the door-rail when moving the emitting spots forward too much for deeper approach.

OA-2VF does not have 1st Row spots during stand-by. Immediately after 2nd Row spots detects, 1st Row spots appear till the 1st Row detection time set up. When entry into 1st Row spots or 2nd Row spots within 1st Row detection time, even if setting time passes, 1st Row spots continue existing. After leaving area, and passing 1st Row detection time, 1st ROW spots are lost again.