Optex MX-50T, MX-40PI, MX-50QZ, MX-40PT Installation Instructions Manual

EASY INSTALLATION

-Easy Wiring Knockout

-Wiring Guide

-Spare Terminal [MX-40QZ/50QZ/50T/40PT Only]

-Tamper Terminal [MX-40QZ/50QZ/50T/40PT Only]

-D.L. Terminal [MX-40QZ(BE)/50QZ(BE) Only]

-Wide Wiring Space

FEATURES

-40ft.×40ft.(12m×12m)Wide Angle [MX-40 Series]

-50ft.×50ft.(15m×15m)Wide Angle [MX-50 Series]

-QUAD Zone Logic

-Patented Multi-focus Lens

-Improved Sealed Optics

-Temperature Compensation Logic

-Pet Immunity [MX-40•PI/PT Only]

(See Section 5 for Pet Immunity)

-Model MX-40PI/50T are UL Listed models.

FUNCTION

-Selectable Pulse Count(2 or 4)

-LED ON/OFF

-Tamper Switch [MX-40QZ/50QZ/50T/40PT Only]

-Microwave Range Selector(LONG or SHORT)

OPTION

-FA-3 Wall & Ceiling Mount Bracket

(Horizontally ±45°&Vertically 0°to-15°)

2.DESCRIPTION,OPERATION and DIMENSIONS

TAMPERSPDLALARM

Corner mount

knockout

Wiring knockout

P.C.B. unit

Tamper switch

Terminals

2.44(62)

Cover

LED Indicator

Lens

Base

Wiring guide

Mounting knockout

(Pitch=3.29"/83.5mm)

(Pitch=3.58"/91.0mm)

Fastening screw

inch(mm)

3. DETECTION AREA

WIDE ANGLE

TOP VIEW

SIDE VIEW

1. INSTALLATION HINTS

Use the pin switch

for Pulse Count

Selection ( 2 or 4 ).

Use the pin switch

for LED ON/OFF .

LED ON/OFF

PULSE COUNT

With PET IMMUNITY&TAMPER

MX-40PT

With PET IMMUNITY

MX-40PIMX-40QZ MX-50QZ MX-50T

PASSIVE INFRARED and MICROWAVE

COMBINATION DETECTOR

P.C.B. hook

: MX-40 AREA

: MX-50 AREA

303525

50 ft

35

30

0

10

9 12

8 ft

15m

50 ft

25

9

4

6

2

0

2

51020

15

20

6

2.2m

0

1510

5

0

3

3

4

6

15m

40

45

12

40

45

5

15

20

6

5

10

15

20

25 ft

8m

25 ft

8m

1.5m

3.0m

2.4m

5 ft

7.5 ft

10 ft

No.59-0967-2 0403-31

N219

4

2

OFF

ON

D.L. TERMINAL

(MX-40QZ(BE),MX-50QZ(BE) Only)

LED can be enabled or disabled remotely from control panel by D.L. terminal.

Place jumper pin switch in OFF position.

MICROWAVE RANGE

LONG

SHORT

EASY WIRING KNOCKOUTS

Press firmly with a screwdriver to

open.Enlarge the hole according

to size of wire.

LED Enabled Connect D.L. terminal to common ground(with detector).

LED Disabled No ground to D.L. terminal (open circuit).

Avoid
Curtain,Screen,etc.
blocking detection area.

Avoid vapor or high
humidity that can cause
condensation.

Avoid direct sunlight.

Do not install outdoors.

Do not aim towards outside areas where there is
frequent movement.

Do not mount in unstable location
where vibration or shock may
affect the detector.

Do not install unit near
fluorescent lights.

Avoid mounting detector where
movement of Fans or Air
Conditioning can be detected.

Do not aim detection area
towards equipment which
continually moves in the
detection area (i.e.curtain,
blinds).

P.I.R. Sensor

Do not touch!

Do not touch!

Microwave Sensor

Select RANGE SELECTOR
according to the room size.
(SHORT or LONG)

MX-40 Series
Select RANGE SELECTOR

"SHORT" when it's used with 24ft

(7m)square and Smaller room.

MX-50 Series

Select RANGE SELECTOR

"SHORT" when it's used with 34ft

(10m)square and Smaller room.

18mA (max.) at 12VDC 20mA (max.) at 12VDC

1. Pet Immunity is most effective on the following sized

animals:Rodents = 0 to 4 inches high

Cats and small to medium sized dogs = 0 to 16 inches

high at normal room temperature.

2. Installation Instructions

a.Mount between 7 and 8 ft. (For better immunity,

especially for medium sized dogs, mount as close

to8ft. as possible.)

b.Do not angle detector towards the ground or use the

angle bracket. Mount flat on the wall or in the corner.

c.For best pet immunity, limit the detectors field of

view to30 ft. maximum in any direction.

d.For rodents

If any shelves within 15 ft.of the detector have a

height that comes wihtin 2.5 ft.below the mounting

height of the detector and rodents can access these

areas, pet immunity will be reduced. Please select

mounting location of detectors carefully to avoid this

situation.

e.For cats and dogs (16 inches in height or less at

normalroom temperature) When a dog jumps up on

desks, the detector may detect it. Adjust detection

area to avoid such places.

f.For cats

If there are cats, any shelves in the detection area will

reduce pet immunity.

g.Pulse Count 4 is not required for Pet Immunity

applications.Use 4 pulse only in harsh environment.

Power wires should not exceed

the following lengths.

When using two or more units on one wire, the

maximum length is obtained by dividing the maximum

wire length listed above by the number of units used.

PROBLEM

REMEDYPROBABLE CAUSE

Correct the voltage supply to 9.5•-16VDC .

LED does not light.

See Section 3.
Turn on the Switch. (See Section 2 )

Incorrect power supply voltage.(disconnection, low voltage)
Incorrect detection area.

LED switch is OFF.

Moving object within area. (curtain,wall hanging, etc.)

LED lights even though no
person is within area.

Remove the source from area, or change location of detector.

Remove object from detection area, or change location of detector.

Rapid temperature changes within area.(heater,air-conditioner, etc.)

7. TROUBLE SHOOTING AND MAINTENANCE

8. SPECIFICATIONS

Faulty wiring.

Wire correctly.

Check load of output.

The unit needs repair or replacement.

LED lights but signal is not sent.

Relay contact is stuck or damaged due to overloading.

6. WIRING

*UL requires MX-40PI, 50T to be connected to a UL

listed power supply capable of providing a nominal

input of 12VDC , 20mA(max.) (at 12VDC )and

battery standby time of 4 hours.

*The equipment shall be installed in accordance with

the National Electrical Code, NFPA 70.

*The Pet Immunity Function has not been evaluated by UL since there are

not established UL requirements for pet immunity.

5. PET IMMUNITY (MX-40PI/40PT Only)

*Specifications and design are subject to change without prior notice.

2140' (650m)

3400' (1020m)

5300' (1600m)

WIRE GAUGE 12VDC

1070' (320m)

1700' (510m)

2700' (820m)

14VDC

AWG 22( 0.33mm )

2

2

AWG 20( 0.52mm )

2

AWG 18( 0.83mm )

4.INSTALLATION

a.Loosen fastening screw and remove cover.

b.Release hook at bottom of P.C.B.unit. Remove

P.C.B. unit from base.

c.Route wires through knockouts along the wiring

guide on the rear side of base. Mount base with

supplied screws. When small animal immunity is

required, refer to Section 5.When using a

bracket,check matching knockout positionbefore

opening mounting hole.

d.Wire according to Section 6.

e.Fix P.C.B.unit into base. Supply power. Allow 1

min. to warm up.

f.Conduct walktest and make adjustments.

(Section 2) Fit cover using fastening screw.

FCC Notice : MX-40PI and MX-50T have been tested and found to comply with the
limits for a field disturbance sensor, pursuant to Part 15 of the FCC Rules. The
user is cautioned that changes or modifications not expressly approved by OPTEX
could void the user's authority to operate this equipment.

TAMPERSPDLALARM

DL TERMINAL

[MX-40QZ(BE)/

50QZ(BE) Only]

TAMPER( N.C. )

[MX-40QZ/50QZ/

50T/40PT Only]

SPARE

[MX-40QZ/50QZ/

50T/40PT Only]

ALARM OUTPUT
( N.C. )

POWER INPUT

(9.5-16VDC )

Pulse Count
Warm up period
Power input
Current draw
Weight
Operating temperature
Environmental humidity
Microwave Frequency
RF interference
D.L. Terminal

Approx. 20 sec 2 or 4

Approx. 1 min

9.5-16VDC

3.9 oz (110g)

-14°F - +131°F (-10°C - +55°C)
95% max.

2.45GHz

No Alarm 20V/m

See Section 2

MODEL
Detection method
Coverage
Detection zones
Mounting Height
Sensitivity
Detection speed
LED Alarm Indicater
Alarm period
Alarm output
Tamper switch

Passive Infrared and Microwave

40 × 40ft. (12 x 12m) 85° wide 50 × 50ft. (15 × 15m) 85° wide

78 zones(PIR)

5-8ft (1.5-2.4m) 7.5-10ft (2.2-3.0m)

3.6°F ( 2°C) at 2ft/sec (0.6m/sec)
1 - 5ft/sec (0.3 - 1.5m/sec)

Switch-able ON/OFF

Approx. 2.5 sec

N.C. , 28VDC 0.2A max.

N.C. , Open when cover is removed. (N.C. , 28VDC 0.1A max.)

MX-50QZ/50TMX-40QZ/PI/PT

This unit is designed to detect movement of an intruder and activate an alarm

control panel. Being only a part of a conplete system,we cannot accept

responsibility for any damages or other consequences resulting from an

intrusion.The following statement will be provided with the equipment as

required by Article 6.3 of the R&TTE Directive, 1999/5/EC.

The Optex MX Series (except MX-40PI and MX-50T) are in conformity with all

essential requirements of the R&TTE Directive (1999/5/EC). This equipment

has been assessed to the following

standards:

I-ETS 300 440: December 1995

ETS 300 683: June 1997

EN 60950: 1992, Incl Amdt 1-4, 11

This product is marked with

which signifies conformity with Class II

product requirements specified in the

R&TTE Directive.

The following table indicates the areas

of intended use of the equipment and

any known restrictions. For countries

not included in this list, please consult

the responsible Spectrum Management

Agency.

NOTE

Country of intended use Restrictions
Austria
Belgium
Denmark
Finland
France
Germany
Greece
Ireland
Italy
Luxembourg
The Netherlands
Spain
Sweden
United Kingdom
Other non EU:Iceland
Norway
Switzerland

2.450GHz