Page 1
INS-CUBE
INS-CUBE
VISUAL VERIFICATION PIR CAMERA
series
INSTALLATION INSTRUCTIONS
Quick Guide
Full information is available at
https://www.optexamerica.com
This “Quick Guide” is the part of the entire installation instructions
•
that guides the installation procedures for installers.
Get the full information of the installation instructions from the web site.
•
If you need a guide to the operation of the whole system, please
•
consult the installer of the entire system.
<< Contents >>
Before installation
- Manufacturer's statement
- Parts identification
- Accessories
- CHeKT account
Step
1
Installation
1-1. Install the mounting bracket
1-2. Remove the main unit from the base unit
1-3. Install/Remove an SD Memory Card
(optional)
1-4. Wiring
1-5. Mounting body
1-6. Secure the main unit to the base unit
DHCP
2
IP address settings
Enable
Disable
For more information about Camera
setting, see our website.
www.optexamerica.com
Page
1
2
3
Before installation
- Manufacturer's statement
Warning
Caution
Warning
Destroy
/Modify
Failure to follow the instructions provided with this indication and improper
handling may cause death or serious injury.
Failure to follow the instructions provided with this indication and improper
handling may cause injury and/or property damage.
Prohibition
Recommendation
Special attention is required to the
NOTE
section of this symbol.
Wetting with waterOutdoor installation
https://support.chekt.com
3
Registration InSight to CHeKT portal site
4
Testing
4-1. Walk test and camera angle checking
4-2. System test
CHeKT support
Others
- Specifications
- LED indications
- Dimensions
- Detection area
- Compliance
Detection through glass
Caution
4
Mounting height
2.0 to 3.0 m (6'7" to 9'8")
3.0 m (9'8") recommended
Partial/complete obscuration
of the detection area.
Tilt
Follow to the Regulations
1
Page 2
- Parts identification
Main unit
Mic
Lens
LED
PIR Sensor
Speaker
- Accessories
- CHeKT account
Base unit
Main unit (Rear side)
If you do not have a CHeKT account, request a dealer
account by visiting the "CHeKT dealer", before Step 3.
SD Card Slot
Lan Port
12V DC Port
Alarm
Terminal Port
Reset / WPS
Illumination Sensor
Refer to the “CHeKT support" for more details.
CHeKT dealer
www.chekt.com/registration
CHeKT support
https://support.chekt.com
Cable Hole.
Mounting Bracktet DC Plug Jack Screw 1pc
Mounting Template
Step
1
Installation
1-1. Install the mounting bracket
Wall mount
Mounting screw x 2
Mounting bracket
Mounting template
Mounting screw x 4
Mounting Screw &
Plastic Anchor-4pcs
Corner mount
1-2. Remove the main unit from the base unit
Press the buttons on the
both sides to release the
main unit.
2
2
Remove the accessory screw, if already installed.
1
1-3. Install/Remove an SD Memory
Card (optional)
Install
Remove
1-4. Wiring
To 12 V DC Port
5
To LAN Port
To Alarm Terminal Port
Main unit (Rear side)
Reset / WPS
NOTE
Factory reset
Press the rest button for 5 seconds
Warning
If you press the Reset button, you will lose all the setting data.
If needed, make a note for further installation.
to return the setup to the factory default.
1
Powe connection
Power source Consumption
12 V DC 6.4 W
IEEE 802.3af Class 3 6.8 W
Caution
Check the voltage and current capacity
of the power source before connecting.
2 Network connection
Connect the crossover cable into the RJ-45.
Alarm connection
3
+12V: 12 V DC power
GND: Ground
T1: Tamper switch
T2: Tamper switch
2
T1 T2 +12VGND
2
1
3
N.O.: Normally open
COM: Common
N.C.: Normally close
N.C
N.O
COM
Page 3
1-5. Mounting body
1-6. Secure the main unit
Press the buttons on both sides to install
1
the main unit.
Base unit
2
Fasten the base unit to the mounting bracket fixed on the wall.
1
Tighten the screw to prevent the base unit movement.
2
The default network type of InSight is dynamic.
If you have a DHCP server, it will automatically set the InSight.
Mounting Bracket
1
Jump to Step 3
Step
2
IP address settings
If you do not have a DHCP server, it will set as follows after one minute.
Initial address: Refer to the label on the InSight
User name: root
Default password: OPTEX
Change your password as appropriate.
1
Fasten the accessory screw to secure the main unit.
2
Step
3
Device registration to CHeKT portal
Setup your CHeKT Dealer Portal:
1. Go to http://dealer.chekt.com/ to log in.
2. Select the Customer on the left side of the dashboard.
3. Select the Site Devices tab.
4. Select the bridge device to be associated with the sensor camera.
5. Access the bridge settings using the gear icon to its right.
6. Select the appropriate tab to register the PIR camera.
Download IP installer;
IP installer is available as a dedicated software for searching
IP addresses of CUBE.
See our website. www.optexamerica.com
Step
4
Testing
4-1. Walk test and camera angle checking
Walk in the detection area to check the detecting performance via LED indication.
Refer to the site for more details.
CHeKT suppor
https://support.chekt.com
4-2. System test
Check the image at the time of detection
on the monitoring portal.
3
Page 4
Others
- Specifications
Model
PIR Detection
Detection method
PIR coverage
Camera
Image sensor
Lens
Min. illumination
IR range
Angle of view
Day/Night
Shutter times
Image and compression
Max. image resolution
Frame rate
Digital noise reduction
Wide dynamic range
Image setting
Video compression
Video bit rate
Audio compression
- LED indicator
Warm-up
[1] ALARM
Blue
INS-CUBE
Passive infrared
Up to 10m, 120° angle of view
1/2.8" Progressive Scan CMOS
2.8mm, F1.6
0.035 lux, AGC on/0 lux with IR (F1.6)
Up to 10m
110°
IR cut filter with auto switch
1/15 s to 1/32,000 s
1,920 x 1,080
60 Hz, 30 fps
3D DNR
Ture WDR
Rotate mode, Saturation, Brightness,
Contrast, Sharpness, AGC, ROI
H.264, H.265, MJPEG
100 kbps to 10 Mbps
G.711
PIR
Red
Stand-by
Green
detection
Wi-Fi
Wireless standard
Frequency range
Channel bandwidth
Protocols
Security
Wireless range
Electrical and interface
Power supply
Power consumption
Communications
Audio input
Audio output
Alarm output (N.O./N.C.)
Tamper alarm (switch)
• Specifications and designs are subject to change without prior notice.
• These un its are designed to detect an int ruder and activate an alarm contr ol panel. Being only a par t of a complet e system,
we cannot accept responsi bility for a ny
IEEE 802.11.b, 802.11g, 802.11n
2.4 GHz to 2.4835 GHz
20 MHz support
802.11b: CCK, QPSK, BPSK
802.11g/n: OFDM
64/128 bit WEP, WPA/WPA2,
WPA-PSK/WPA2-PSk, WPS
25 m (Dependent upou environment)
12 V DC ±10%, PoE (802.3af)
12 V DC 6.4 W, PoE (802.3af) 6.8 W
1 RJ45 10 M/100 M Ethernet port
Built-in microphone
Built-in speaker
1 channel signal
1 channel signal
damage s or other co nsequences res ulting fro m an intru sion.
Environmental and mechanical
Operarion temperature
Environmental humidity
Dimensions
Weight
Functions
Alarm triggers
Local storage
Security
Protocols
-20°C - 50°C (-4°F - 122°F)
90% max
87.6 mm x 114 mm x 72.1 mm
297 g
PIR detection, Network disconnect
IP address conflict, Storage exception
Temperature critical, Audio detection
Built-in Micro SD, SDHC, SDXC
card slot, up to 128 GB
One-key reset, Flash-prevention,
Dual stream, Password protection,
Privacy mask, IP address filtering,
Anonymous access
TCP/IP, ICMP, HTTP, HTTPS, DHCP,
DNS, DDNS, RTP, RTSP, RTCP, NTP,
UPnP, SNMP, IGMP, 802.1X, QoS,
IPv6, Bonjour
- Dimensions
87.6 (3.45)
72.1 (2.84)
[2] STATUS
[3] LINK
Wired LAN
Wi-Fi
- Detection area
Top view
Side view
Blue
Yellow
Yellow
120°
Yellow
1 s interval
Yellow
0.5 s intrval
0 5 10 15 20 25 30 ft.
10 m
8
6
4
2
0
2
4
6
8
10
0 2 4 6 8 10 m
0 5 10 15 20 25 30 ft.
2 m
1
0 2 4 6 8 10 m
Yellow
Yellow
30 ft
25
Camera
20
15
10
5
0
5
10
15
20
25
30
8 ft.
6.6
4
PIR
114 (4.49)
Unit: mm (inch)
60 (2.36)
96.8 (3.81)
- Compliance
Personal Information
This product is equipped with the function to produce moving and/or still image of the designated area and its surrounding
and can store the recorded imagewhich includes the information such as face of an individual that could identify the
individual. Prior to the installation of this product, the compliance to local laws and regulations needs to be confirmed by the
user of this product for the lawful installation and use of this product, and signage and notification when using this product.
User of this product is deemed to be responsible for the compliance of any laws and regulations relating to personal
information, privacy protection and rights of portrait upon use of this product. Image taken by this product is required to be
treated appropriately under the responsibility of the user of this product. OPTEX Co., Ltd. and its subsidiaries (hereinafter
collectively called “OPTEX") shall not wilfully obtain or utilise the image taken by this product. However, only when dealing
with troubles of this product upon request of user, OPTEX may obtain and utilize the necessary image recorded by this
product. When doing so, OPTEX shall not treat such image for the purpose of identifying an individual. OPTEX shall treat
such image according to its Privacy Policy. When requesting OPTEX to support a trouble of this product, the user may be
required to perform applicable legal notification. Ensure to follow the appropriate procedure prior to sharing of personal
information and data to OPTEX. Installation of this product, producing image, monitoring, recording with camera and
handling of personal information or data shall all be performed under discretion and responsibility of user of this product,
and OPTEX shall not be held liable for any dispute between a user and a third party.
FCC notification
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed andused in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
About distribution of source code for open source software
This product includes open source software（” OSS”） distributed under OSS License. In compliance with the OSS Licenses
such as GPL (GNU GENERAL PUBLIC LICENSE), LGPL (GNU LESSERGENERAL PUBLIC LICENSE), and/or others
included, we are making the source code of the OSS available, at the actual cost, to our customer upon his/her request.
The source code corresponding to OSS included in this product will be provided in a prescribed manner for at least than
three(3) years after the date of purchase. Please note that the OSS is provided without warranty of any kind.
Distributed by
OPTEX INC./AMERICAS HQ (U.S.)
www.optexamerica.com
4
Loading...