Optex FTN-AM, FTN-ST Installation

N219

CONTENTS

1 INTRODUCTION

1-1 BEFORE INSTALLATION ................2

1-2 PARTS IDENTIFICATION ................3

1-3 DETECTION AREA..........................3

2 INSTALLATION

2-1 INSTALLATION ................................4

3 WALK TEST

3-1 WALK TEST .....................................7

4 DIP SWITCH SETTING

4-1 LED ..................................................8

4-2 ALARM OUTPUT .............................8

4-3 PIR SENSITIVITY ............................8

4-4 ANTI-MASKING ...............................8

5 OTHERS

5-1 WALL TAMPER (OPTION)

CONNECTION.................................9

5-2 EXAMPLE OF EOL WIRING .........10

5-3 LED LIGHT PATTERN ...................11

6 SPECIFICATIONS

6-1 SPECIFICATIONS .........................11

6-2 DIMENSIONS ................................12

FTN-ST Standard model with 2 PIRs
FTN-AM FTN-ST with anti-masking

Compact design

190° adjustable bracket

Intelligent AND logic

Digital anti-masking (AM model)

Wall tamper (option)

•

•

•

•

•

NO.59-1645-0 091201

INSTALLATION INSTRUCTIONS

Compact outdoor
detector

Compact outdoor
detector

fit series

fit series

- 1 -

1

INTRODUCTION

1-1

BEFORE INSTALLATION

Warning

Failure to follow the instructions provided with this indication and improper
handling may cause death or serious injury.

Caution

Failure to follow the instructions provided with this indication and improper
handling may cause injury and/or property damage.

The check mark indicates recommendation.

The nix sign indicates prohibition.

Warning

Caution

Do not remove the PCB. Do not touch the PCB except for the DIP switch.

ON

2 3 4

1

Mounting height. Keep the detector parallel to the

ground.

Consider the direction a person is
approaching from, as well as the
detection area.

Install the detector in a place where it is free from false alarm factors. For example:

Sunlight and reflection

•

Heat source

•

Objects moving in the wind

•

0.8 – 1.2 m
(2'7" – 3'11")

Parallel

Tilt

- 2 -

0

10

0'0'5'

5'

5'

10'

10'

10'

15'

15'

15'

2 3 4 5

1

1

1

2

3

4

5

(m)

(ft.)

(ft.)

(m)

2

4

5

3

1-2

PARTS IDENTIFICATION

-Optional accessories

Wall tamper (WRS-02)

Bracket

Sponge

Fixture

Main unit

Main unit cover

Lens

Screw kit

Screw (3 × 20 mm)

0' 5' 10' 15'

0.8

0

(m)

1.0

1.2

2'7"

0'

(ft.)

3'3"
3'11"

10 2 3 4 5

(m)

(ft.)

0' 5' 10' 15'

0.8

0

(m)

1.0

1.2
10 2 3 4 5

(m)

2'7"

0'

(ft.)

3'3"
3'11"

(ft.)

1-3

DETECTION AREA

Top view Side view

2 m detection length

5 m detection length

Adjustable range: 95° (by 5° pitch)

Adjustable range: 95° (by 5° pitch)

Sponge

- 3 -

2

INSTALLATION

2-1

INSTALLATION

1

Open the main unit cover.

2

Remove the fixture.

FixtureFixture

3

Hold the top of the bracket lifted and

remove the main unit.

Bracket

Main unit

2

1

Bracket

Main unit

2

1

4

Put the wire extending from the wall

through the wiring hole in the bottom of
the bracket, and mount the bracket on
the wall.

Note>>

For wall tamper wiring (option), refer to
page 9.

•

Screw (3 × 20 mm)

Screw (3 × 20 mm)

Mounting height:

0.8 – 1.2 m
(2'7" – 3'11")

Sponge

Screw (3 × 20 mm)

Screw (3 × 20 mm)

Mounting height:

0.8 – 1.2 m
(2'7" – 3'11")

Sponge

5

Pull the wire through the main unit. Lift the top of the bracket slightly and mount

the main unit to the bracket.

1

3

2

83.5 mm
(3.29")

- 4 -

6

Wire terminal connections.

Notes>>

Anti-masking output is recognized as TROUBLE.
For EOL, refer to page 10.

-Power cable length

The power cable should be limited to the following length.

Unit: m (ft.)

Cable diameter

FTN-ST FTN-AM

12 V 14 V 12 V 14 V

AWG22 (0.33 mm2)

340

(1,120')

730

(2,400')

290

(950')

620

(2,030')

AWG20 (0.52 mm2)

530

(1,740')

1,160

(3,810')

450

(1,480')

980

(3,220')

AWG18 (0.83 mm2)

850

(2,790')

1,850

(6,070')

720

(2,360')

1,570

(5,150')

•

•

Power input (+)

Power input (-)

Alarm output

COM

Spare

Tamper

Power input (+)

Power input (-)

Alarm output

COM

Trouble output

Tamper

FTN-ST FTN-AM

Power input (+)

Power input (-)

Alarm output

COM

Spare

Tamper

Power input (+)

Power input (-)

Alarm output

COM

Trouble output

Tamper

FTN-ST FTN-AM

7

Determine the horizontal detection angle and attach the fixture.

Note>>

To make adjustments, remove the fixture.

•

Note>>

Check that the fixture and bracket
engage correctly.

•

Note>>

Check that the fixture and bracket
engage correctly.

•

Angle pitch: 5°

95°

95°

Angle pitch: 5°

95°

95°

+ -

AL C SP TP TP

+ -

AL C TR TP TP

- 5 -

8

Determine the detection length. (2 m or 5 m)

If 2 m is required, rotate the lower lens
180 degrees.

Note>>

Do not remove the upper lens.•

If 2 m is required, rotate the lower lens
180 degrees.

Note>>

Do not remove the upper lens.•

5 m detection length
(Factory default)

2 m detection length

Side view

0' 5' 10' 15'

0.8

0

(m)

1.0

1.2

2'7"

0'

(ft.)

3'3"
3'11"

10 2 3 4 5

(m)

(ft.)

0' 5' 10' 15'

2'7"

0'

(ft.)

3'3"
3'11"

0.8

0

(m)

1.0

1.2

(ft.)

10 2 3 4 5

(m)

Side view

5 m detection length
(Factory default)

2 m detection length

Side view

0' 5' 10' 15'

0.8

0

(m)

1.0

1.2

2'7"

0'

(ft.)

3'3"
3'11"

10 2 3 4 5

(m)

(ft.)

0' 5' 10' 15'

2'7"

0'

(ft.)

3'3"
3'11"

0.8

0

(m)

1.0

1.2

(ft.)

10 2 3 4 5

(m)

Side view

9

Attach the main unit cover.

Note>>

To prepare for walk test, check that DIP
switch 1 (LED) is set to “ON” before
attaching the main unit cover.

•

10

Perform walk test.

For details, refer to page 7.

- 6 -

3

If the LED does not need to be turned

on at all times, set the DIP switch 1
(LED) to “OFF”.

ON

1 2 3 4

ON

1 2 3 4

DIP switch

ON

1 2 3 4

ON

1 2 3 4

DIP switch

2

Check that LED lights for 2 seconds

when the intended object is detected.

1

Set DIP switch 1 (LED) to “ON”.

Note>>

The switch is set to “ON” by factory
default.

•

ON

1 2 3 4

ON

1 2 3 4

DIP switch

ON

1 2 3 4

ON

1 2 3 4

DIP switch

3

WALK TEST

3-1

WALK TEST

Detected

Not detected

- 7 -

4-1

LED

DIP switch 1

FTN-ST

FTN-AM

ON

1 2 3 4

ON

OFF

Position Function

ON

(Factory default)

LED ON

OFF LED OFF

4-2

ALARM OUTPUT

DIP switch 2

FTN-ST

FTN-AM

ON

1 2 3 4

N.O.

N.C.

Position Function

N.O. N.O. output

N.C.

(Factory default)

N.C. output

4-3

PIR SENSITIVITY

DIP switch 3

FTN-ST

FTN-AM

ON

1 2 3 4

STD

LOW

Position Function

STD

(Factory default)

Normal sensitivity

LOW Low sensitivity

4-4

ANTI-MASKING

DIP switch 4

FTN-ST

FTN-AM

ON

1 2 3 4

Position Function

ON

(Factory default)

ANTI-MASKING ON

OFF ANTI-MASKING OFF

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

ON

1 2 3 4

●: Factory default

DIP switch

1 LED

2 ALARM OUTPUT

3 PIR SENSITIVITY

4 ANTI-MASKING

4

DIP SWITCH SETTING

ON

2 3 4

1

Do not touch the PCB
except for the DIP switch
and the terminal.

ON

OFF

- 8 -

5-1

WALL TAMPER (OPTION) CONNECTION

Connect the tamper lead as shown below when connecting a wall tamper (option).

CAL+SP TP TP

Wall tamper (option)
WRS-02

Twist and swage the wires.

Control panel

-ANTI-MASKING function

When masking condition continues more than 3 minutes, TROUBLE will be generated.
TROUBLE is generated after 20 seconds under the anti-masking test mode.

Note>>

If a trouble is output (mal-detection of anti-masking) immediately after the operation has
started, set the DIP switch 4 (ANTI-MASKING) to “OFF” and then to “ON”, and close the
cover.

•

Teaching mode starts when the main unit cover are attached.
Please be careful not to leave any object within 1 m from the unit.

ANTI-MASKING test mode

The trouble is output after 20 seconds.

Normal mode

The trouble is output after 3 minutes.

10 minutes

Teaching

1 minute

-Mounting position

Note>>

Pull the wire through the bracket
before installing the wall tamper
(option).

•

5

OTHERS

Bracket

Sponge

- 9 -

1 2 3 4 5 6 7

Alarm relay Trouble relay Tamper

Tamper-EOL-ResistanceAlarm-EOL-Resistance

Control panel Control panel

Positive (+)

terminal

Negative (-)

terminal

Alarm

(N.C./N.O.)

COM Trouble (N.C.) Tamper (N.C.) Tamper (N.C.)

5-2

EXAMPLE OF EOL WIRING

Since the alarm and trouble outputs share the COM terminal, the wire connection should be
made for the fit series detector according to the following diagram.

-Double EOL

-Triple EOL

1 2 3 4 5 6 7

Alarm relay Trouble relay Tamper

Tamper-EOL-ResistanceAlarm-EOL-Resistance

Control panel Control panel

Positive (+)

terminal

Negative (-)

terminal

Alarm

(N.C./N.O.)

COM Trouble (N.C.) Tamper (N.C.) Tamper (N.C.)

1 2 3 4 5 6 7

Alarm relay Trouble relay Tamper

Tamper-EOL­Resistance

Alarm-EOL­Resistance

Control panel Control panel

Positive (+)

terminal

Negative (-)

terminal

Alarm

(N.C./N.O.)

COM Trouble (N.C.) Tamper (N.C.) Tamper (N.C.)

Trouble-EOL­Resistance

- 10 -

5-3

LED LIGHT PATTERN

The following explains the LED light pattern.

Detector condition LED indicator

Warm-up

Note>>

The LED blinks even if the DIP
switch 4 (LED) is set to “OFF”.

•
Blinks for approx. 60 seconds.

Alarm

Lights for 2 seconds.

Masking detection
(FTN-RAM only)

Note>>

The LED blinks even if the DIP
switch 4 (LED) is set to “OFF”.

•

Blinks 3 times and then repeats.

LED

Blink Light OFF

6

SPECIFICATIONS

6-1

SPECIFICATIONS

Model FTN-ST FTN-AM
Detection method Passive infrared
PIR coverage 5 × 1 m (16'5" × 3'3")
Detection length limit 2 m, 5 m (6'7", 16'5")
Detectable speed 0.3 – 1.5 m/s (1' – 4'11"/s)
Sensitivity 2.0°C (at 0.6 m/s) (3.6°F (at 2'/s))
Operating voltage 9.5 – 18 V DC
Current draw 17 mA (max.) (at 12 V DC)

20 mA (max.) (at 12 V DC)
Alarm period 2.0 ±1.0 sec.
Warm-up period Approx. 60 sec. (LED blinks)
Alarm output N.C./N.O. Selectable 28 V DC 0.1 A (max.)
Trouble output N.C. 28 V DC 0.1 A (max.), open when the cover is removed.
LED indicator Light/Blink: Warm-up, alarm, masking detection (FTN-AM only)
Operation temperature -20 – +60°C (-4 – +140°F)
Environment humidity 95% max.
Weatherproof IP55
Mounting Wall (Outdoor, Indoor)
Mounting height 0.8 – 1.2 m (2'7" – 3'11")
Weight 100 g (3.5 oz.)
Accessories Screw (3 × 20 mm) × 2

*Specifications and design are subject to change without prior notice.

- 11 -

6-2

DIMENSIONS

Unit: mm (inch)

35 (1.38") 42.5 (1.67")

155 (6.10")

Unit: mm (inch)

35 (1.38") 42.5 (1.67")

155 (6.10")

OPTEX INCORPORATED (USA)

TEL:[phone]
Tech:[phone]
URL:http://www.optexamerica.com/

OPTEX KOREA CO., LTD. (KOREA)

TEL:[phone]
URL:http://www.optexkorea.com/

OPTEX SECURITY Sp. z o. o. (POLAND)

TEL:[phone]
URL:http://www.optex.com.pl/

OPTEX (DONGGUAN) CO., LTD.
SHENZHEN OFFICE (CHINA)

TEL:[phone]
URL:http://www.optexchina.com/

OPTEX CO., LTD. (JAPAN)

(ISO 9001 Certified)
(ISO 14001 Certified)

5-8-12 Ogoto Otsu
Shiga 520-0101
JAPAN
TEL:[phone]
FAX:[phone]
URL:http://www.optex.co.jp/e/

OPTEX (EUROPE) LTD. (UK)

TEL:[phone]
URL:http://www.optexeurope.com/

OPTEX SECURITY SAS (FRANCE)

TEL:[phone]
URL:http://www.optex-security.com/

Note>>

These units are designed to detect an intruder and activate an alarm control panel. Being
only a part of a complete system, we cannot accept responsibility for any damages or other
consequences resulting from an intrusion. These products confirm to the EMC Directive
2004/108/EC.

•

- 12 -