Optex AX-100, 200TFR, AX-100TFR, AX-200TFR, AX-200TFRTI Basic Configuration Manual

AXTFR Basic configuration guide
AX100/200TFRTI Configuration guide
AX100/200TFR (30M/60M Battery powered active beams)
AX100/200TFR set a new benchmark for reliable, flexible, low maintenance
external detection systems. CCTV, Intruder, hazard alerts and numerous other
applications can be serviced by this flexible battery powered technology
Compatible
with most
Wireless
transmitters
Minimal site
survey
investment
cable or
power
surge
No
=
Cost
Reduction
system
design
time
Minimal
damage or
site
disruption
Flexible Tower
or single beam
configuration
options
3-5 YEAR BATTERY LIFE
AX100/200TFR (30M/60M Battery powered active beams)
Undulating ground can cause missed alarms when using long range beams on perimeters
Undulating ground can be easily managed with Battery powered AXTFR option and prevent missed alarms
In CCTV applications a single long range beam makes it difficult to direct the camera to where the intruder is?
Multiple short range beam can direct PTZ to target position
AX TFR can provide target recognition in areas
where activity is expected
but needs to be ignored
A ONLY Activated = CLOSED CIRCUIT = No Alarm (Not interesting) B ONLY Activated = OPEN CIRCUIT = ALARM (Possible threat)
A+B Both Activated = CLOSED CIRCUIT = Truck (Not interesting)
A = NO
B = NC
These configurations could be reversed to detect larger targets and ignore others No need for any power infrastructure means that installation is completed in hours rather than days. This is critical for some public transport and public service sectors
AX100/200TFR (30M/60M Battery powered active beams)
AX100/200 TFR can signal an alarm via wireless, GSM, pager or hardwired connection if available. A typical example of cable use is where existing cables are limited or have been damaged.
Battery power means that site security can be expanded easily, moved or used as temporary security installations.
Interchangeable signalling mediums means you are never restricted to one protocol. AXTFR can move with the times and your customer needs
4 Channel frequency makes Tower configuration easy
Simple battery replacement
1st Step
Loosen
4th Step
2nd Step
Remove
3rd Step
Put back
Battery replacement does not involve interference with alignment system
AX100/200TFR (30M/60M Battery powered active beams)
(1)Front Cover (2)Back Box (3)Wall
Triple tamper
AX TFR can provide security
where zone block causes a major
problem
Conventional solution has higher risk of detection blocking and false alarms
AXTFR can overcome and eliminate these problems
Secure windows and balcony access Early warning for low bridge
Driveways and gates for vehicle
Monitor access to roof or fire escape
and pedestrian detection
No mains po wer supply
needed
Simply mount and align the
beams
AX100/200TFR (30M/60M Battery powered active beams)
AX100/200 TFR are supplied as standard with no batteries and no wireless transmitters. This is because the AXTFR can utilize numerous wireless technologies including : Honeywell, Visonic, Scantronics, Inovonics etc
Each set of AX100/200TFR require 4 LHS20 batteries to power the devices. Two for the TX and two for the RX. Based on these batteries the beams can be powered for 5 years (AX100TRF) and 3 years (AX200TFR).
If you wish to signal the output from the device via your choice of wireless technology then you can ac­commodate the wireless device within the AXTFR housing.
Note there are numerous configurations available. The installer needs to consider the application and signalling requirements. The following pages are examples of how various configurations are possible using Inovonics wireless products
Common option for CCTV or Intruder
Using AX100/200TFRTI Version. (These can also be used with 16 channel 1216M Receiver)
Here we have 2 sets of beams signalling Alarm, tamper, low battery and supervisory. The EE1210 is fitted at the AXTFR Transmitter and Receiver
Note
Tamper output is common.
Typical option for CCTV
Here we have 4 sets of beams signalling Alarm, tamper, low battery and supervisory. The EE1212 is an option to the EE1210.
Dome Pre-set
Dome Pre-set
Note
AX100/200TFRTI are supplied fitted with x2 EE1210 and require x4 LHS20
Basic option for CCTV or Intruder
Here we have 4 sets of beams signalling limited Alarm, tamper, low battery and supervisory. The EE1210 is fitted only at the AXTFR Receiver
Note
No tamper Signal sent From AXTFR Transmitter
AX-100/200TRF Supplied as standard with no batteries and no wireless transmitters.
AX-100/200TRFTI Supplied as standard with no batteries and two EE1210 wireless transmitters.
LHS20 Batteries Not supplied as standard with any product. Four required for each set of beams
Note for Inovonics recievers 4 Channel receiver has 4 Alarm outputs 16 channel receiver has 9 outputs
Specifications may change without notice. Please contact our office for any site survey assistance or advice you may require on 01628631000
Loading...