OPTEK OPL583 Datasheet
Prod uct Bul le tin OPL583
August 1996
Dual Chan nel Pho tologic® En coder De tec tor
Type OPL583
Fea tures
• Two matched de tec tors with pho to -
litho graphic con trol of rela tive po si tion
• Dual Pho tologic
pack age pro vides re duced com po nent
count
®
cir cuitry in sin gle
• Open col lec tor inverter out put for flexi -
bil ity of cir cuit in ter face
• Low cost plas tic hous ing
De scrip tion
The OPL583 contains a monolithic
integrated circuit which incorporates two
independent photodiodes, linear
amplifiers, Schmitt trigger circuits, and
output transistors served by a common
voltage regulator. The outputs are
TTL/LSTTL compatible and can drive 8
TTL loads over a voltage range from 4.5
to 16 V. Applications include linear and
rotary encoders with resolutions
determined by external apertures. The
fixed relative position of the two
photodiodes and the matched
characteristics of the two channels allow
considerable design flexibility.
Ab so lute Maxi mum Rat ings (TA = 25o C un less oth er wise noted)
Sup ply Volt age. . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V
Stor age Tem pera ture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40o C to +100o C
Op er ate Tem pera ture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40o C to +85o C
Lead Sol der Tem pera ture [1/16 inch (1.6 mm) from case for 5 sec. with sol der ing iron]
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260o C
Power Dis si pa tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mW
Du ra tion of Out put Short to VCC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.00 sec.
Volt age At Out put . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V
Low Level Out put Cur rent (sink ing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 mA
Notes:
(1) Derate linearly 2.67 mW/o C above 25o C.
(2) RMA flux is recommended. Duration can be extended to 10 sec. max when flow soldering.
Max 20 grams force may be applied to leads when flow soldering.
(3) A 0.01 µF capacitor should be used across the VCC and GND leads to stabilize the power
supply line.
(4) Irradiance measurements are made with λ = 940 nm.
(5) Derate linearly 0.37 V/o C above 58o C.
(5)
(2)
(1)
Sche matic
V
4
CC
V
REG
3
AMP
OUT B
2
AMP
OUT A
1 GND
Op tek Tech nol ogy, Inc. 1215 W. Crosby Road Car roll ton, Texas 75006 (972) 323- 2200 Fax (972) 323- 2396
4-16
Type OPL583
Elec tri cal Char ac ter is tics (TA = 25o C, VCC = 4.5 V - 16 V un less oth er wise noted)
SYM BOL PA RAME TER MIN TYP MAX UNITS TEST CON DI TIONS
(3)
(4)
4.5 16 V
0.05 0.10 0.25 mW/cm
0.67 1.00 1.50
8.5 12.0 mA
3.5 6.0 mA
6 mA
1.0 30.0
2
10
20
15
µA
µs
µs
ns
ns
2
Ee = 0.5 mW/cm2, No Load on Output
Ee = 0 mW/cm2, No Load on Output
Ee = 0 mW/cm2 and 0.5 mW/cm
Ee = 0 mW/cm2, VOH = 16 V
Vcc = 5 V, RL = 360 Ω
Ee = 0 or 0.5 mW/cm2, f = 10 kHz,
D.C. = 50%
E
V
CC
eT(+)
Operating Supply Voltage
Positive Going Threshold Irradiance
EeT(+)/EeT(-) Hysteresis Ratio 1.1 1.5 2.0
MATCH
Channel Match
EeT(+,A)/EeT(+,B)
Supply Current
I
CCL
Both Outputs Low
(Both Photodiodes Irradiated)
Supply Current
I
CCH
Both Outputs High
(Both Photodiodes Shaded)
I
CCM
I
OH
V
OL
Supply Current
Mixed Output States (One High, One Low)
High Level Output Current
Low Level Output Voltage 0.21 0.40 V Ee = 0.5 mW/cm2, IOL = 12.8 mA
Propagation Delay
T
T
PHL
PLH
t
r
t
f
Output High to Low
Output Low to High
Output Rise Time
Output Fall Time
2
Typi cal Per form ance Curves
Angular Displacement from
Package Mechanical Axis
Based on IL vs.
Angular Displacement
readings from 5
photodiode-bonded
samples
Angular Response (Typ) - 0
Normalized Threshold Irradiance
vs. Ambient Temperature
V
= 5 V
CC
λ = 940 nm
EeT(-)
EeT(+)
o
TA - Ambient Temperature - oC
Supply Current vs. Ambient
Temperature
V
= 16 V
CC
No Load On Output
λ = 940 nm
Ee = 0.5 mW/cm2 for I
Ee = 0.0 mW/cm2 for I
I
CCL
I
CCH
TA - Ambient Temperature - oC
CCL
CCH
Op tek re serves the right to make changes at any time in or der to im prove de sign and to sup ply the best prod uct pos si ble.
Op tek Tech nol ogy, Inc. 1215 W. Crosby Road Car roll ton, Texas 75006 (972)323- 2200 Fax (972)323- 2396
4-17
Loading...