OPTEK OPI120TXV, OPI120TX Datasheet
Fea tures
• High current transfer ratio
• 15 kV electrical isolation
• Base lead provided for conventional
transistor biasing
• Components processed to Optek’s
screening program patterned after
MIL-PRF-19500 for TX and TXV
devices
De scrip tion
The OPI120TX and OPI120TXV are
optically coupled isolators, each
consisting of a gallium aluminum
arsenide infrared light emitting diode
(OP235TX or OP235TXV) and an NPN
silicon phototransistor (OP804TX or
OP804TXV) sealed in a high dielectric
plastic housing. This series is designed
for applications requiring high voltage
isolation between input and output.
High reliability processing is performed at
the component level in accordance with
MIL-PRF-19500 for both the infrared light
emitting diode and the NPN silicon
phototransistor.Typical screening and lot
acceptance tests are provided on page
13-4.
Ab so lute Maxi mum Rat ings (TA = 25o C un less oth er wise noted)
Input- to- Output Iso la tion Volt age . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 15 kVDC
(1)
Op er at ing Tem pera ture Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65o C to +125o C
Stor age Tem pera ture Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65o C to +150o C
Sol der ing Tem pera ture [1/16 inch (1.6 mm) from case for 5 sec. with sol der ing
iron] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240o C
In put Di ode
For ward DC Cur rent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA
Re verse Volt age. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0 V
Power Dis si pa tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mW
(2)
Out put Pho to sen sor
Con tinu ous Col lec tor Cur rent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
Collector- Base Volt age . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 V
Collector- Emitter Volt age. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 V
Emitter- Base Volt age . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 V
Power Dis si pa tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 mW
(3)
Notes:
(1) Measured with input leads shorted together and output leads shorted together in air with a
maximum relative humidity of 50%. If suitably encapsulated or oil immersed, the isolation
voltage is increased to at least 25 kV.
(2) Derate linearly 2.0 mW/o C above 25o C.
(3) Derate linearly 2.5 mW/o C above 25o C.
(4) Methanol or isopropanol are recommended as cleaning agents.
Prod uct Bul le tin OPI120TX/TXV
Sep tem ber 1996
Hi- Rel Op ti cally Cou pled Iso la tor
Types OPI120TX, OPI120TXV
Op tek Tech nol ogy, Inc. 1215 W. Crosby Road Car roll ton, Texas 75006 (972) 323- 2200 Fax (214) 323- 2396
13-46
Types OPI120TX, OPI120TXV
Elec tri cal Char ac ter is tics (TA = 25o C un less oth er wise noted)
SYM BOL PA RAME TER MIN TYP MAX UNITS TEST CON DI TIONS
In put Di ode
V
F
Forward Voltage
(5)
1.00 1.40 1.70 V IF = 30 mA
1.20 1.60 1.90 V IF = 30 mA, TA = -55o C
0.90 1.15 1.50 V IF = 30 mA, TA = 100o C
I
R
Reverse Current 0.1 10
µA
VR = 2 V
Out put Pho to tran sis tor
V
(BR)CBO
Collector-Base Breakdown Voltage 30 40 V
IC = 100 µA, IE = 0, IF = 0
V
(BR)CEO
Collector-Emitter Breakdown Voltage 30 40 V
IC = 100 µA, IB = 0, IF = 0
V
(BR)EBO
Emitter-Base Breakdown Voltage 5.0 V
IE = 100 µA, IC = 0, IF = 0
I
C(OFF)
Collector-Emitter Dark Current 0.2 100 nA VCE = 10 V, IB = 0, IF = 0,
10 100
µA
VCE = 10 V, IB = 0, IF = 0, TA = 100o C
I
CB(OFF)
Collector-Base Dark Current 0.1 10.0 nA VCB = 10 V, IE = 0, IF = 0
Cou pled
I
C(ON)
On-State Collector Current
(5)
2.0 mA VCE = 5 V, IB = 0, IF = 10 mA
1.2 mA VCE = 5 V, IB = 0, IF = 10 mA, TA = -55o C
1.2 mA VCE = 5 V, IB = 0, IF = 10 mA, TA = 100o C
V
CE(SAT)
Collector-Emitter Saturation Voltage 0.25 0.30 V IC = 2 mA, IB = 0, IF = 20 mA
V
ISO
Isolation Voltage (Input to Output) 15.0 30.0 kV See Note 1
t
r
Output Rise Time 8.0 15.0
µs VCC = 10 V, IC = 2 mA, RL = 100 Ω
t
f
Output Fall Time 8.0 15.0
µs VCC = 10 V, IC = 2 mA, RL = 100 Ω
(5) Measurement is taken during the last 500 µs of a single 1.0 ms test pulse. Heating due to increased pulse rate or pulse width can cause change
in measurement results.
Optek reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Op tek Tech nol ogy, Inc. 1215 W. Crosby Road Car roll ton, Texas 75006 (972) 323- 2200 Fax (214) 323- 2396
13-47
Loading...