Prod uct Bul le tin OPB916
November 2000
Photologic Slotted Op ti cal Switches
Type OPB916 Series
[30.73]
1.21
[24.38]
.96
[2.54]
.10
[12.19]
.48
[3.18]
2X R .125
[14.99 0.38]
±
.590 ± .015
[5.08]
.20
[16.51]
.650 REF
[609.6]
24.0 MIN
[1.4 ± 0.51]
.055 ± .02
Fea tures
Choice of output configuration
•
24” min 26 AWG wires
•
• Low power consumption
[1.02]
4X R .125
[3.18]
2X .125
NOTE 6
OPTICAL C
[4.95]
.195
[3.81]
.15
L
WIRE COLOR
WHITE
BLUE
GREEN
RED
BLACK
[6.48]
.255
[19.30]
.760
WIRE: 26 AWG, 7 STRAND
PVC INSUL., UL RATED
IDENTITY
COLLECTOR
OUTPUT
EMITTER
ANODE
CATHODE
[3.18]
.125
De scrip tion
The OPB916 consists of an infrared
emitting diode and a Photologic photo
integrated circuit mounted in an opaque
housing with clear windows for dust
protection. The deep slot allows for a
longer reach of the optical path from the
mounting plane, .650” (16.51 mm).
Internal apertures are .010” x 0.06” for
the Photologic’s “S side” and .050” x
0.06” for the LED, “E side”. Two logic
states and two electrical output types are
available.
Custom electrical, wire or cabling are
available. Contact your local
representative or Optek for more
information.
Visit our website at www.optekinc.com
or email us at sensors@optekinc.com
[ 8.89 ± 0.51]
.35 ± .02
[ 8.13 ± 0.51]
.32 ± .02
[ 7.62 ]
.30 REF
DIMENSIONS ARE IN INCHES [MILLIMETERS]
TOLERANCE ± .010 [0.25]
Ab so lute Maxi mum Rat ings (TA = 25o C un less oth er wise noted)
Sup ply Volt age VCC (Not to ex ceed 3 sec.) .............................. 18 V
Stor age and Op er ating Tem per a ture Range.................... -40° C to +80° C
In put Di ode Power Dis si pa tion ................................... 100 mW
Out put Photologic Power Dis si pa tion .............................. 90 mW
Volt age at Out put Lead (Open Col lec tor Out put) .......................... 35 V
Di ode For ward D.C. Cur rent ........................................ 50 mA
Di ode Re verse D.C. Volt age .......................................... 2 V
NOTES:
(1) De rate lin early 1.67 mW/° C above 25° C.
(2) De rate lin early 2.67 mW/° C above 70° C.
(3) Clear dust protection.
(4) Normal application would be with light source blocked, simulated by IF = 0 mA.
(5) All parameters tested using pulse technique.
PRECAUTIONS: Exposure of the plastic body to chlorinated hydrocarbons and ketones such
as thread lock and instant adhesive products will degrade the plastic body. Cleaning agents
methanol and isopropanol are recommended. Spray or wipe do not submerge.
(1)
(2)
Op tek Tech nol ogy, Inc. 1215 W. Crosby Road Car roll ton, Texas 75006 (972) 323- 2200 Fax (972) 323- 2396
33
Type OPB916 Series
PART NUMBER GUIDE
Optek
Assembly
O P B 9 1 6 X X X
Photologic
Photo Integrated
Circuit
Optical Center
Line .90”
Schematics
OPB916B
Anode
(Red)
BUFFER WITH 10K PULL-UP RESISTOR
Electrical Specification Variations
B - Buffered with 10K Ω pull-up
BOC - Buffered Open-Collector Output
I - Inverted with 10K Ω pull-up
IOC - Inverted Open-Collector Output
OPB916I
VREG
AMP
V
CC
(White)
OUTPUT
(Blue)
Anode
(Red)
INVERTER WITH 10K PULL-UP RESISTOR
VREG
AMP
CC
V
(White)
OUTPUT
(Blue)
Cathode
(Black)
Anode
(Red)
Cathode
(Black)
LIGHT ON - OUTPUT HIGH
BUFFER OPEN COLLECTOR
VREG
AMP
LIGHT ON - OUTPUT HIGH
GROUND
(Green)
CC
V
(White)
OUTPUT
(Blue)
GROUND
(Green)
Cathode
(Black)
Anode
(Red)
Cathode
(Black)
LIGHT ON - OUTPUT LOW
OPB916OCIOPB916BOC
INVERTER OPEN COLLECTOR
VREG
AMP
LIGHT ON - OUTPUT LOW
GROUND
(Green)
V
CC
(White)
OUTPUT
(Blue)
GROUND
(Green)
Optek Tech nol ogy, Inc. 1215 W. Crosby Road Carrollton, Texas 75006 (972)323-2200 Fax (972)323-2396
35
Loading...