OpenEye OE-C3012T4 Quick Start Guide
CONNECTIONS
11RJ-45
For network and PoE connections
2
Power
(12vDC)*
Power connection
11Thread lock cap
44Rubber “O” ring
22Rubber plug
55Camera cable
33RJ45 enclosure
11Reset Button
To restore the camera to factory
defaults:
1.
Disconnect power for 30
seconds.
2.
Reconnect power and wait
30 seconds.
3.
Press and hold the reset
button for 20 seconds.
22MicroSD Card Slot
Supports up to 512GB microSD
card for Edge storage.
Do not add or remove the
microSD card when the camera
is powered on.
1
1
2
1
2
RJ-45
Power
(12vDC)*
For network and PoE connections
Power connection
*12vDC power input port should be plugged when not in use.
To restore the camera to factory
defaults:
1.
Disconnect power for 30
Reset Button
MicroSD Card Slot
2
seconds.
2.
Reconnect power and wait
30 seconds.
3.
Press and hold the reset
button for 20 seconds.
Supports up to 512GB microSD
card for Edge storage.
Do not add or remove the
microSD card when the camera
is powered on.
This quick start guide provides only basic information on the camera’s settings and
operation for initial installation. Please read the user manual for optimal camera
confi gurations.
Waterproof Cable
Liberty Lake, WA, USA
509.232.5261
openeye.net
5
Thread lock cap
Rubber plug
RJ45 enclosure
4
3
1
2
QUICK START GUIDE
Rubber “O” ring
Camera cable
Copyright ©2021 OpenEye.
All Rights Reserved. Information contained in this document is
subject to change without prior notice. OpenEye does its best to
provide accurate information but cannot be held responsible for
typos or mistakes.
37465AD
OE-C3012T4
4MP | Autofocus | Turret
openeye.net
CONTENTS
OE-C3012T4
Turret Camera
Self-Tapping
Screws &
Plastic Anchors
Mounting Template
Waterproof Cable
Connector
Quick Start
Guide
INSTALLATION
Connect a network cable to the camera
using the RJ45 input and connect the
other end of the cable to your network
switch or recorder.
1. Apply template sticker to desired
camera location.
2. Drill anchor holes using included
mounting template.
3. Remove mounting template.
4. Insert anchors.
5. Mount camera.
6. Connect network cable with
included waterproof cable
connector.
7. Adjust camera view.
POWER
This camera is compatible with 12vDC
and Power over Ethernet (PoE). If you
are connecting 12vDC power, verify the
polarity of the power connection.
ETHERNET CABLE
CONNECTIONS
Connect a network cable to the camera
using the RJ45 input and connect the
other end of the cable to your network
switch or recorder.
DEFAULT USERNAME
AND PASSWORD
NOTE: OpenEye IP cameras ship
without a default password.
The admin user password can be set
using the following methods:
1. OpenEye recorders running Apex
2.1 or newer will automatically set
a new unique password if:
Connected to an M-Series
recorder with a built in PoE
switch.
Connected to a network
switch through the
camera network port
and selected then added in
setup, if a new password has
not already been set.
2. Connect to the camera directly
through a Web Browser and follow
the onscreen prompts.
3. Use the Network Camera Manager
(NCM) Utility.
Username: admin
NOTE: The NCM software manual can be found
at https://www.openeye.net/ncm-manual
NOTE: Refer to your Apex recorder manualor
quick start guide for instruction on
adding cameras. Passwords must be
9-32 characters including at least two
elements of the following three: digits,
letters, and special characters.
ASSIGNING AN
IP ADDRESS
OpenEye IP cameras are set to DHCP
by default. If a DHCP server is not
detected after 4 minutes, the camera
will default to IP address 192.168.51.2.
If you are not using a DHCP server,
NCM will allow you to batch confi gure a
static IP address.
The IP address for the camera network
on your Apex recorder is 192.168.51.1.
NOTE: To change this IP address please refer to
your Apex recorder manual.
Selecting multiple cameras and entering IP address 192.168.51.2 will set
an IP address on all selected cameras,
starting at 192.168.51.2 and increase
per camera.
1. Open the Network Camera
Manager application.
2. Select applicable camera(s).
3. Input starting IP address, Subnet
Mask, Gateway, DNS.
4. Apply changes.
5. Wait 60 seconds before refreshing
NCM.
CONNECTING TO THE
IP CAMERA
To access the camera setup menu,
you need to open Network Camera
Manager (NCM) utility. NCM is preinstalled on all OpenEye Recorders,
and is also available for download on
the OpenEye website for installation on
your personal computer or laptop.
1. Open Network Camera Manager.
2. Locate your camera on the
Network Camera Manager list.
3. To open the web browser, select
the camera and click LOAD.
PRODUCT FEATURES
Camera
Maximum Resolution 2688x1520
Frame Rate at
Maximum Resolution
Total Streams Dual Streaming
ONVIF Profi le S / G / T Compliant
Day/Night True Day / Night
Wide Dynamic Range True WDR
Environmental and Power
Power
Consumption
Input Voltage 12vDC / PoE
Pan / Tilt / Rotate
IP Rating IP67
30FPS @ 4MP H.264/H.265
8.16W maximum
Pan: 0° ~ 360°
Tilt: 0° ~ 90°
Rotate: 0° ~ 360°
Loading...