OpenEye OE-C1012D2 Quick Start Guide

CONNECTIONS

1

2

1

2

3

3

4

1

2

4

3

4

2

1

DC12V IN

11 RJ-45RJ-45 For network and PoE connectionsFor network and PoE connections

22 Power (12vDC)*Power (12vDC)* Power connectionPower connection

GreyGrey Audio OutAudio Out

33 Audio I/OAudio I/O

44 Alarm I/OAlarm I/O

*12vDC power input port should be plugged when not in use.

11 Reset ButtonReset Button

22 MicroSD Card SlotMicroSD Card Slot

PurplePurple Ground Ground

Green Green Audio InAudio In

BrownBrown GroundGround

YellowYellow Alarm Out +Alarm Out +

WhiteWhite Alarm Out -Alarm Out -

OrangeOrange Alarm InputAlarm Input

BlueBlue GroundGround

To restore the camera to factoryTo restore the camera to factory
defaults:defaults:

1. 1. Disconnect power for 30 Disconnect power for 30
seconds.seconds.

2. 2. Reconnect power and wait Reconnect power and wait
30 seconds.30 seconds.

3. 3. Press and hold the reset Press and hold the reset
button for 20 seconds.button for 20 seconds.

Supports up to 512GB microSD Supports up to 512GB microSD
card for Edge storage.card for Edge storage.

Do not add or remove the Do not add or remove the
microSD card when the camera microSD card when the camera
is powered on.is powered on.

This quick start guide provides only basic information on the camera’s
settings and operation for initial installation. Please read the user manual for

optimal camera congurations.

Waterproof Cable

5

Liberty Lake, WA, USA
509-232-5261

openeye.net

4

3

11 Thread lock capThread lock cap 44 Rubber “O” ringRubber “O” ring
22 Rubber plugRubber plug 55 Camera cableCamera cable
33 RJ45 enclosureRJ45 enclosure

Copyright ©2021 OpenEye.
All Rights Reserved. Information contained in this document is
subject to change without prior notice. OpenEye does its best to
provide accurate information but cannot be held responsible for
typos or mistakes.

1

2

QUICK START GUIDE

OE-C1012D2

2MP | Outdoor | Mini Dome

37483AC openeye.net

CONTENTS INSTALLATION

1. Apply template sticker to desired

camera location.

2. Drill anchor holes using included

mounting template.

OE-C1012D2

Dome Camera

Waterproof Cable

Connector

3. Remove mounting template.

4. Insert anchors.

5. Mount camera.

6. Connect network cable with

included waterproof cable

Security Torx

Tool

connector.

7. Adjust camera view.

8. Secure Lid / dome

Self-Tapping

Screws &

Plastic Anchors

DEFAULT USERNAME
AND PASSWORD

Mounting Template

NOTE: OpenEye IP cameras ship

without a default password.

Quick Start

Guide

Optional Free Paintable Dome Cover

This camera has an available paintable dome
cover allowing it to be quickly converted to a
black housing or the allow custom painting to
match its installation environment. To reduce
waste it is not included in every package but
may be requested free of charge at time of
purchase.

POWER

This camera is compatible with 12vDC
and Power over Ethernet (PoE). If you
are connecting 12vDC power, verify the
polarity of the power connection.

NOTE: If the camera will be exposed

to inclement weather, OpenEye
recommends sealing around the
camera base, or connection to
mounting surface with outdoor
waterproof caulking.

The admin user password can be set
using the following methods:

1. OpenEye recorders running Apex

2.1 or newer will automatically set
a new unique password if:

• Connected to an M-Series
recorder with a built in PoE
switch.

• Connected to a network
switch through the
camera network port
and selected then added in
setup, if a new password has
not already been set.

2. Connect to the camera directly

through a Web Browser and follow
the onscreen prompts.

3. Use the Network Camera Manager

(NCM) Utility.

Username: admin

NOTE: The NCM software manual can be

found at https://www.openeye.net/

ncm-manual

NOTE: Refer to your Apex recorder manualor

quick start guide for instruction on
adding cameras. Passwords must be
9-32 characters including at least two
elements of the following three: digits,
letters, and special characters.

ASSIGNING AN
IP ADDRESS

OpenEye IP cameras are set to DHCP
by default. If a DHCP server is not
detected after 4 minutes, the camera
will default to IP address 192.168.51.2.
If you are not using a DHCP server,

NCM will allow you to batch confi gure a

static IP address.
The IP address for the camera network
on your Apex recorder is 192.168.51.1.

NOTE: To change this IP address please refer to

your Apex recorder manual.

Selecting multiple cameras and enter­ing IP address 192.168.51.2 will set
an IP address on all selected cameras,
starting at 192.168.51.2 and increase
per camera.

1. Open Network Camera Manager.

2. Select applicable camera(s).

3. Input starting IP address, Subnet

Mask, Gateway, DNS.

4. Apply changes.

5. Wait 60 seconds before refreshing

NCM.

CONNECTING TO THE
IP CAMERA

To access the camera setup menu,
you need to open Network Camera
Manager (NCM) utility. NCM is pre­installed on all OpenEye Recorders,
and is also available for download on
the OpenEye website for installation on
your personal computer or laptop.

1. Open Network Camera Manager.

2. Locate your camera on the

Network Camera Manager list.

3. To open the web browser, select

the camera and click LOAD.

PRODUCT FEATURES

Camera

Maximum Resolution 1920x1080

Frame Rate at
Maximum Resolution

Total Streams Dual Streaming

ONVIF Profi le S / G / T Compliant

Day/Night True Day / Night

Wide Dynamic Range True WDR

Environmental and Power

Power
Consumption

Input Voltage 12vDC / PoE

Pan / Tilt / Rotate

IP Rating IP67

Impact Rating IK10

30FPS @ 2MP H.264/H.265

5.5W Max

Pan: 3° ~ 360°

Tilt: 0° ~ 68°

Rotate: 3° ~ 360°